Sintesi e caratterizzazione di nanopolveri composite allumina-zirconia

Il presente lavoro di tesi riguarda la sintesi di nanopolveri allumina-zirconia, seguendo tre differenti metodologie (sintesi per coprecipitazione, sintesi con il metodo dei citrati, sintesi idrotermale assistita da microonde) e il trattamento termico (calcinazione) delle polveri ottenute, mediante tecniche di riscaldamento convenzionali ed alternative (microonde). Lo scopo del lavoro è consistito nell’individuare, tra le tecniche esaminate, quella più idonea e conveniente, per la preparazione di nanopolveri cristalline 95 mol% Al2O3 – 5 mol% ZrO2 e nell’esaminare gli effetti che la calcinazione condotta con le microonde, ha sulle caratteristiche finali delle polveri, rispetto ai trattamenti termici convenzionali. I risultati ottenuti al termine del lavoro hanno evidenziato che, tra le tecniche di sintesi esaminate, la sintesi idrotermale assistita da microonde, risulta il metodo più indicato e che, il trattamento termico eseguito con le microonde, risulta di gran lunga vantaggioso rispetto a quello convenzionale. La sintesi idrotermale assistita da microonde consente di ottenere polveri nano cristalline poco agglomerate, che possono essere facilmente disaggregate e con caratteristiche microstrutturali del tutto peculiari. L’utilizzo di tale tecnica permette, già dopo la sintesi a 200°C/2ore, di avere ossido di zirconio, mentre per ottenere gli ossidi di alluminio, è sufficiente un ulteriore trattamento termico a basse temperature e di breve durata (400°C/ 5 min). Si è osservato, inoltre, che il trattamento termico condotto con le microonde comporta la formazione delle fasi cristalline desiderate (ossidi di alluminio e zirconio), impiegando (come per la sintesi) tempi e temperature significativamente ridotti. L’esposizione delle polveri per tempi ridotti e a temperature più basse consente di evitare la formazione di aggregati duri nelle nanopolveri finali e di contrastare il manifestarsi di fenomeni di accrescimento di grani, preservando così la “nanostruttura” delle polveri e le sue caratteristiche proprietà.

Zirconia in dentistry

The above factors emphasize the scope of this thesis for further investigations on zirconia, the improvement of all-ceramic zirconia restorations, and especially the interaction of zirconia and veneering and its influence on the performance of the whole restoration. The introduction, chapter 1, gave a literature overview on zirconia ceramics. In chapter 2, the objective of the study was to evaluate the effect of abrading before and after sintering using alumina-based abrasives on the surface of yttria-tetragonal zirconia polycrystals. Particular attention was paid to the amount of surface stress–assisted phase transformation (tetragonal→monoclinic) and the presence of microcracks. Chapter 3 is based on the idea that the conventional sintering techniques for zirconia based materials, which are commonly used in dental reconstruction, may not provide a uniform heating, with consequent generation of microstructural flaws in the final component. As a consequence of the sintering system, using microwave heating, may represent a viable alternative. The purpose of the study was to compare the dimensional variations and physical and microstructural characteristics of commercial zirconia (Y-TZP), used as a dental restoration material, sintered in conventional and microwave furnaces. Chapter 4 described the effect of sandblasting before and after sintering on the surface roughness of zirconia and the microtensile bond strength of a pressable veneering ceramic to zirconia.

Sviluppi di catalizzatori per l'abbattimento di NOx in presenza di ossigeno

Il traffico veicolare è la principale fonte antropogenica di NOx, idrocarburi (HC) e CO e, dato che la sostituzione dei motori a combustione interna con sistemi alternativi appare ancora lontana nel tempo, lo sviluppo di sistemi in grado di limitare al massimo le emissioni di questi mezzi di trasporto riveste un’importanza fondamentale. Sfortunatamente non esiste un rapporto ottimale aria/combustibile che permetta di avere basse emissioni, mentre la massima potenza ottenibile dal motore corrisponde alle condizioni di elevata formazione di CO e HC. Gli attuali sistemi di abbattimento permettono il controllo delle emissioni da sorgenti mobili tramite una centralina che collega il sistema di iniezione del motore e la concentrazione di ossigeno del sistema catalitico (posto nella marmitta) in modo da controllare il rapporto aria/combustibile (Fig. 1). Le marmitte catalitiche per motori a benzina utilizzano catalizzatori “three way” a base di Pt/Rh supportati su ossidi (allumina, zirconia e ceria), che, dovendo operare con un rapporto quasi stechiometrico combustibile/comburente, comportano una minore efficienza del motore e consumi maggiori del 20-30% rispetto alla combustione in eccesso di ossigeno. Inoltre, questa tecnologia non può essere utilizzata nei motori diesel, che lavorano in eccesso di ossigeno ed utilizzano carburanti con un tenore di zolfo relativamente elevato. In questi ultimi anni è cresciuto l’interesse per il controllo delle emissioni di NOx da fonti veicolari, con particolare attenzione alla riduzione catalitica in presenza di un eccesso di ossigeno, cioè in condizioni di combustione magra. Uno sviluppo recente è rappresentato dai catalizzatori tipo “Toyota” che sono basati sul concetto di accumulo e riduzione (storage/reduction), nei quali l’NO viene ossidato ed accumulato sul catalizzatore come nitrato in condizioni di eccesso di ossigeno. Modificando poi per brevi periodi di tempo le condizioni di alimentazione da ossidanti (aria/combustibile > 14,7 p/p) a riducenti (aria/combustibile < 14,7 p/p) il nitrato immagazzinato viene ridotto a N2 e H2O. Questi catalizzatori sono però molto sensibili alla presenza di zolfo e non possono essere utilizzati con i carburanti diesel attualmente in commercio. Obiettivo di questo lavoro di tesi è stato quello di ottimizzare e migliorare la comprensione del meccanismo di reazione dei catalizzatori “storage-reduction” per l’abbattimento degli NOx nelle emissioni di autoveicoli in presenza di un eccesso di ossigeno. In particolare lo studio è stato focalizzato dapprima sulle proprietà del Pt, fase attiva nei processi di storage-reduction, in funzione del tipo di precursore e sulle proprietà e composizione della fase di accumulo (Ba, Mg ed una loro miscela equimolare) e del supporto (γ-Al2O3 o Mg(Al)O). Lo studio è stato inizialmente focalizzato sulle proprietà dei precursori del Pt, fase attiva nei processi di storage-reduction, sulla composizione della fase di accumulo (Ba, Mg ed una loro miscela equimolare) e del supporto (γ-Al2O3 o Mg(Al)O). E’ stata effettuata una dettagliata caratterizzazione chimico-fisica dei materiali preparati tramite analisi a raggi X (XRD), area superficiale, porosimetria, analisi di dispersione metallica, analisi in riduzione e/o ossidazione in programmata di temperatura (TPR-O), che ha permesso una migliore comprensione delle proprietà dei catalizzatori. Vista la complessità delle miscele gassose reali, sono state utilizzate, nelle prove catalitiche di laboratorio, alcune miscele più semplici, che tuttavia potessero rappresentare in maniera significativa le condizioni reali di esercizio. Il comportamento dei catalizzatori è stato studiato utilizzando differenti miscele sintetiche, con composizioni che permettessero di comprendere meglio il meccanismo. L’intervallo di temperatura in cui si è operato è compreso tra 200-450°C. Al fine di migliorare i catalizzatori, per aumentarne la resistenza alla disattivazione da zolfo, sono state effettuate prove alimentando in continuo SO2 per verificare la resistenza alla disattivazione in funzione della composizione del catalizzatore. I principali risultati conseguiti possono essere così riassunti: A. Caratteristiche Fisiche. Dall’analisi XRD si osserva che l’impregnazione con Pt(NH3)2(NO2)2 o con la sospensione nanoparticellare in DEG, non modifica le proprietà chimico-fisiche del supporto, con l’eccezione del campione con sospensione nanoparticellare impregnata su ossido misto per il quale si è osservata sia la segregazione del Pt, sia la presenza di composti carboniosi sulla superficie. Viceversa l’impregnazione con Ba porta ad una significativa diminuzione dell’area superficiale e della porosità. B. Caratteristiche Chimiche. L’analisi di dispersione metallica, tramite il chemiassorbimento di H2, mostra per i catalizzatori impregnati con Pt nanoparticellare, una bassa dispersione metallica e di conseguenza elevate dimensioni delle particelle di Pt. I campioni impregnati con Pt(NH3)2(NO2)2 presentano una migliore dispersione. Infine dalle analisi TPR-O si è osservato che: Maggiore è la dispersione del metallo nobile maggiore è la sua interazione con il supporto, L’aumento della temperatura di riduzione del PtOx è proporzionale alla quantità dei metalli alcalino terrosi, C. Precursore Metallo Nobile. Nelle prove di attività catalitica, con cicli ossidanti e riducenti continui in presenza ed in assenza di CO2, i catalizzatori con Pt nanoparticellare mostrano una minore attività catalitica, specie in presenza di un competitore come la CO2. Al contrario i catalizzatori ottenuti per impregnazione con la soluzione acquosa di Pt(NH3)2(NO2)2 presentano un’ottima attività catalitica, stabile nel tempo, e sono meno influenzabili dalla presenza di CO2. D. Resistenza all’avvelenamento da SO2. Il catalizzatore di riferimento, 17Ba1Pt/γAl2O3, mostra un effetto di avvelenamento con formazione di solfati più stabili che sul sistema Ba-Mg; difatti il campione non recupera i valori iniziali di attività se non dopo molti cicli di rigenerazione e temperature superiori ai 300°C. Per questi catalizzatori l’avvelenamento da SO2 sembra essere di tipo reversibile, anche se a temperature e condizioni più favorevoli per il 1.5Mg8.5Ba-1Pt/γAl2O3. E. Capacità di Accumulo e Rigenerabilità. Tramite questo tipo di prova è stato possibile ipotizzare e verificare il meccanismo della riduzione. I catalizzatori ottenuti per impregnazione con la soluzione acquosa di Pt(NH3)2(NO2)2 hanno mostrato un’elevata capacità di accumulo. Questa è maggiore per il campione bimetallico (Ba-Mg) a T < 300°C, mentre per il riferimento è maggiore per T > 300°C. Per ambedue i catalizzatori è evidente la formazione di ammoniaca, che potrebbe essere utilizzata come un indice che la riduzione dei nitrati accumulati è arrivata al termine e che il tempo ottimale per la riduzione è stato raggiunto o superato. Per evitare la formazione di NH3, sul catalizzatore di riferimento, è stata variata la concentrazione del riducente e la temperatura in modo da permettere alle specie adsorbite sulla superficie e nel bulk di poter raggiungere il Pt prima che l’ambiente diventi troppo riducente e quindi meno selettivo. La presenza di CO2 riduce fortemente la formazione di NH3; probabilmente perché la CO2, occupando i siti degli elementi alcalino-terrosi lontani dal Pt, impedisce ai nitriti/nitrati o all’H2 attivato di percorrere “elevate” distanze prima di reagire, aumentando così le possibilità di una riduzione più breve e più selettiva. F. Tempo di Riduzione. Si è migliorata la comprensione del ruolo svolto dalla concentrazione dell’agente riducente e dell’effetto della durata della fase riducente. Una durata troppo breve porta, nel lungo periodo, alla saturazione dei siti attivi, un eccesso alla formazione di NH3 Attraverso queste ultime prove è stato possibile formulare un meccanismo di reazione, in particolare della fase riducente. G. Meccanismo di Riduzione. La mobilità dei reagenti, nitriti/nitrati o H2 attivato è un elemento fondamentale nel meccanismo della riduzione. La vicinanza tra i siti di accumulo e quelli redox è determinante per il tipo di prodotti che si possono ottenere. La diminuzione della concentrazione del riducente o l’aumento della temperatura concede maggiore tempo o energia alle specie adsorbite sulla superficie o nel bulk per migrare e reagire prima che l’ambiente diventi troppo riducente e quindi meno selettivo.

Studio del comportamento meccanico di smalti porcellanati per substrati metallici

Composite porcelain enamels are inorganic coatings for metallic components based on a special ceramic-vitreous matrix in which specific additives are randomly dispersed. The ceramic-vitreous matrix is made by a mixture of various raw materials and elements and in particular it is based on boron-silicate glass added with metal oxides(1) of titanium, zinc, tin, zirconia, alumina, ecc. These additions are often used to improve and enhance some important performances such as corrosion(2) and wear resistance, mechanical strength, fracture toughness and also aesthetic functions. The coating process, called enamelling, depends on the nature of the surface, but also on the kind of the used porcelain enamel. For metal sheets coatings two industrial processes are actually used: one based on a wet porcelain enamel and another based on a dry-silicone porcelain enamel. During the firing process, that is performed at about 870°C in the case of a steel substrate, the enamel raw material melts and interacts with the metal substrate so enabling the formation of a continuous varying structure. The interface domain between the substrate and the external layer is made of a complex material system where the ceramic vitreous and the metal constituents are mixed. In particular four main regions can be identified, (i) the pure metal region, (ii) the region where the metal constituents are dominant compared with the ceramic vitreous components, (iii) the region where the ceramic vitreous constituents are dominant compared with the metal ones, and the fourth region (iv) composed by the pure ceramic vitreous material. It has also to be noticed the presence of metallic dendrites that hinder the substrate and the external layer passing through the interphase region. Each region of the final composite structure plays a specific role: the metal substrate has mainly the structural function, the interphase region and the embedded dendrites guarantee the adhesion of the external vitreous layer to the substrate and the external vitreous layer is characterized by an high tribological, corrosion and thermal shock resistance. Such material, due to its internal composition, functionalization and architecture can be considered as a functionally graded composite material. The knowledge of the mechanical, tribological and chemical behavior of such composites is not well established and the research is still in progress. In particular the mechanical performances data about the composite coating are not jet established. In the present work the Residual Stresses, the Young modulus and the First Crack Failure of the composite porcelain enamel coating are studied. Due to the differences of the porcelain composite enamel and steel thermal properties the enamelled steel sheets have residual stresses: compressive residual stress acts on the coating and tensile residual stress acts on the steel sheet. The residual stresses estimation has been performed by measuring the curvature of rectangular one-side coated specimens. The Young modulus and the First Crack Failure (FCF) of the coating have been estimated by four point bending tests (3-7) monitored by means of the Acoustic Emission (AE) technique(5,6). In particular the AE information has been used to identify, during the bending tests, the displacement domain over which no coating failure occurs (Free Failure Zone, FFZ). In the FFZ domain, the Young modulus has been estimated according to ASTM D6272-02. The FCF has been calculated as the ratio between the displacement at the first crack of the coating and the coating thickness on the cracked side. The mechanical performances of the tested coated specimens have also been related and discussed to respective microstructure and surface characteristics by double entry charts.

Structural changes and dynamic behaviour of vanadium oxide-based catalysts for gas-phase selective oxidations

Selective oxidation is one of the simplest functionalization methods and essentially all monomers used in manufacturing artificial fibers and plastics are obtained by catalytic oxidation processes. Formally, oxidation is considered as an increase in the oxidation number of the carbon atoms, then reactions such as dehydrogenation, ammoxidation, cyclization or chlorination are all oxidation reactions. In this field, most of processes for the synthesis of important chemicals used vanadium oxide-based catalysts. These catalytic systems are used either in the form of multicomponent mixed oxides and oxysalts, e.g., in the oxidation of n-butane (V/P/O) and of benzene (supported V/Mo/O) to maleic anhydride, or in the form of supported metal oxide, e.g., in the manufacture of phthalic anhydride by o-xylene oxidation, of sulphuric acid by oxidation of SO2, in the reduction of NOx with ammonia and in the ammoxidation of alkyl aromatics. In addition, supported vanadia catalysts have also been investigated for the oxidative dehydrogenation of alkanes to olefins , oxidation of pentane to maleic anhydride and the selective oxidation of methanol to formaldehyde or methyl formate [1]. During my PhD I focused my work on two gas phase selective oxidation reactions. The work was done at the Department of Industrial Chemistry and Materials (University of Bologna) in collaboration with Polynt SpA. Polynt is a leader company in the development, production and marketing of catalysts for gas-phase oxidation. In particular, I studied the catalytic system for n-butane oxidation to maleic anhydride (fluid bed technology) and for o-xylene oxidation to phthalic anhydride. Both reactions are catalyzed by systems based on vanadium, but catalysts are completely different. Part A is dedicated to the study of V/P/O catalyst for n-butane selective oxidation, while in the Part B the results of an investigation on TiO2-supported V2O5, catalyst for o-xylene oxidation are showed. In Part A, a general introduction about the importance of maleic anhydride, its uses, the industrial processes and the catalytic system are reported. The reaction is the only industrial direct oxidation of paraffins to a chemical intermediate. It is produced by n-butane oxidation either using fixed bed and fluid bed technology; in both cases the catalyst is the vanadyl pyrophosphate (VPP). Notwithstanding the good performances, the yield value didn’t exceed 60% and the system is continuously studied to improve activity and selectivity. The main open problem is the understanding of the real active phase working under reaction conditions. Several articles deal with the role of different crystalline and/or amorphous vanadium/phosphorous (VPO) compounds. In all cases, bulk VPP is assumed to constitute the core of the active phase, while two different hypotheses have been formulated concerning the catalytic surface. In one case the development of surface amorphous layers that play a direct role in the reaction is described, in the second case specific planes of crystalline VPP are assumed to contribute to the reaction pattern, and the redox process occurs reversibly between VPP and VOPO4. Both hypotheses are supported also by in-situ characterization techniques, but the experiments were performed with different catalysts and probably under slightly different working conditions. Due to complexity of the system, these differences could be the cause of the contradictions present in literature. Supposing that a key role could be played by P/V ratio, I prepared, characterized and tested two samples with different P/V ratio. Transformation occurring on catalytic surfaces under different conditions of temperature and gas-phase composition were studied by means of in-situ Raman spectroscopy, trying to investigate the changes that VPP undergoes during reaction. The goal is to understand which kind of compound constituting the catalyst surface is the most active and selective for butane oxidation reaction, and also which features the catalyst should possess to ensure the development of this surface (e.g. catalyst composition). On the basis of results from this study, it could be possible to project a new catalyst more active and selective with respect to the present ones. In fact, the second topic investigated is the possibility to reproduce the surface active layer of VPP onto a support. In general, supportation is a way to improve mechanical features of the catalysts and to overcome problems such as possible development of local hot spot temperatures, which could cause a decrease of selectivity at high conversion, and high costs of catalyst. In literature it is possible to find different works dealing with the development of supported catalysts, but in general intrinsic characteristics of VPP are worsened due to the chemical interaction between active phase and support. Moreover all these works deal with the supportation of VPP; on the contrary, my work is an attempt to build-up a V/P/O active layer on the surface of a zirconia support by thermal treatment of a precursor obtained by impregnation of a V5+ salt and of H3PO4. In-situ Raman analysis during the thermal treatment, as well as reactivity tests are used to investigate the parameters that may influence the generation of the active phase. Part B is devoted to the study of o-xylene oxidation of phthalic anhydride; industrially, the reaction is carried out in gas-phase using as catalysts a supported system formed by V2O5 on TiO2. The V/Ti/O system is quite complex; different vanadium species could be present on the titania surface, as a function of the vanadium content and of the titania surface area: (i) V species which is chemically bound to the support via oxo bridges (isolated V in octahedral or tetrahedral coordination, depending on the hydration degree), (ii) a polymeric species spread over titania, and (iii) bulk vanadium oxide, either amorphous or crystalline. The different species could have different catalytic properties therefore changing the relative amount of V species can be a way to optimize the catalytic performances of the system. For this reason, samples containing increasing amount of vanadium were prepared and tested in the oxidation of o-xylene, with the aim of find a correlations between V/Ti/O catalytic activity and the amount of the different vanadium species. The second part deals with the role of a gas-phase promoter. Catalytic surface can change under working conditions; the high temperatures and a different gas-phase composition could have an effect also on the formation of different V species. Furthermore, in the industrial practice, the vanadium oxide-based catalysts need the addition of gas-phase promoters in the feed stream, that although do not have a direct role in the reaction stoichiometry, when present leads to considerable improvement of catalytic performance. Starting point of my investigation is the possibility that steam, a component always present in oxidation reactions environment, could cause changes in the nature of catalytic surface under reaction conditions. For this reason, the dynamic phenomena occurring at the surface of a 7wt% V2O5 on TiO2 catalyst in the presence of steam is investigated by means of Raman spectroscopy. Moreover a correlation between the amount of the different vanadium species and catalytic performances have been searched. Finally, the role of dopants has been studied. The industrial V/Ti/O system contains several dopants; the nature and the relative amount of promoters may vary depending on catalyst supplier and on the technology employed for the process, either a single-bed or a multi-layer catalytic fixed-bed. Promoters have a quite remarkable effect on both activity and selectivity to phthalic anhydride. Their role is crucial, and the proper control of the relative amount of each component is fundamental for the process performance. Furthermore, it can not be excluded that the same promoter may play different role depending on reaction conditions (T, composition of gas phase..). The reaction network of phthalic anhydride formation is very complex and includes several parallel and consecutive reactions; for this reason a proper understanding of the role of each dopant cannot be separated from the analysis of the reaction scheme. One of the most important promoters at industrial level, which is always present in the catalytic formulations is Cs. It is known that Cs plays an important role on selectivity to phthalic anhydride, but the reasons of this phenomenon are not really clear. Therefore the effect of Cs on the reaction scheme has been investigated at two different temperature with the aim of evidencing in which step of the reaction network this promoter plays its role.

Catalytic liquid- and gas-phase oxidations for the synthesis of intermediates and specialty chemicals: some examples of industrial relevance

Nowadays, it is clear that the target of creating a sustainable future for the next generations requires to re-think the industrial application of chemistry. It is also evident that more sustainable chemical processes may be economically convenient, in comparison with the conventional ones, because fewer by-products means lower costs for raw materials, for separation and for disposal treatments; but also it implies an increase of productivity and, as a consequence, smaller reactors can be used. In addition, an indirect gain could derive from the better public image of the company, marketing sustainable products or processes. In this context, oxidation reactions play a major role, being the tool for the production of huge quantities of chemical intermediates and specialties. Potentially, the impact of these productions on the environment could have been much worse than it is, if a continuous efforts hadn’t been spent to improve the technologies employed. Substantial technological innovations have driven the development of new catalytic systems, the improvement of reactions and process technologies, contributing to move the chemical industry in the direction of a more sustainable and ecological approach. The roadmap for the application of these concepts includes new synthetic strategies, alternative reactants, catalysts heterogenisation and innovative reactor configurations and process design. Actually, in order to implement all these ideas into real projects, the development of more efficient reactions is one primary target. Yield, selectivity and space-time yield are the right metrics for evaluating the reaction efficiency. In the case of catalytic selective oxidation, the control of selectivity has always been the principal issue, because the formation of total oxidation products (carbon oxides) is thermodynamically more favoured than the formation of the desired, partially oxidized compound. As a matter of fact, only in few oxidation reactions a total, or close to total, conversion is achieved, and usually the selectivity is limited by the formation of by-products or co-products, that often implies unfavourable process economics; moreover, sometimes the cost of the oxidant further penalizes the process. During my PhD work, I have investigated four reactions that are emblematic of the new approaches used in the chemical industry. In the Part A of my thesis, a new process aimed at a more sustainable production of menadione (vitamin K3) is described. The “greener” approach includes the use of hydrogen peroxide in place of chromate (from a stoichiometric oxidation to a catalytic oxidation), also avoiding the production of dangerous waste. Moreover, I have studied the possibility of using an heterogeneous catalytic system, able to efficiently activate hydrogen peroxide. Indeed, the overall process would be carried out in two different steps: the first is the methylation of 1-naphthol with methanol to yield 2-methyl-1-naphthol, the second one is the oxidation of the latter compound to menadione. The catalyst for this latter step, the reaction object of my investigation, consists of Nb2O5-SiO2 prepared with the sol-gel technique. The catalytic tests were first carried out under conditions that simulate the in-situ generation of hydrogen peroxide, that means using a low concentration of the oxidant. Then, experiments were carried out using higher hydrogen peroxide concentration. The study of the reaction mechanism was fundamental to get indications about the best operative conditions, and improve the selectivity to menadione. In the Part B, I explored the direct oxidation of benzene to phenol with hydrogen peroxide. The industrial process for phenol is the oxidation of cumene with oxygen, that also co-produces acetone. This can be considered a case of how economics could drive the sustainability issue; in fact, the new process allowing to obtain directly phenol, besides avoiding the co-production of acetone (a burden for phenol, because the market requirements for the two products are quite different), might be economically convenient with respect to the conventional process, if a high selectivity to phenol were obtained. Titanium silicalite-1 (TS-1) is the catalyst chosen for this reaction. Comparing the reactivity results obtained with some TS-1 samples having different chemical-physical properties, and analyzing in detail the effect of the more important reaction parameters, we could formulate some hypothesis concerning the reaction network and mechanism. Part C of my thesis deals with the hydroxylation of phenol to hydroquinone and catechol. This reaction is already industrially applied but, for economical reason, an improvement of the selectivity to the para di-hydroxilated compound and a decrease of the selectivity to the ortho isomer would be desirable. Also in this case, the catalyst used was the TS-1. The aim of my research was to find out a method to control the selectivity ratio between the two isomers, and finally to make the industrial process more flexible, in order to adapt the process performance in function of fluctuations of the market requirements. The reaction was carried out in both a batch stirred reactor and in a re-circulating fixed-bed reactor. In the first system, the effect of various reaction parameters on catalytic behaviour was investigated: type of solvent or co-solvent, and particle size. With the second reactor type, I investigated the possibility to use a continuous system, and the catalyst shaped in extrudates (instead of powder), in order to avoid the catalyst filtration step. Finally, part D deals with the study of a new process for the valorisation of glycerol, by means of transformation into valuable chemicals. This molecule is nowadays produced in big amount, being a co-product in biodiesel synthesis; therefore, it is considered a raw material from renewable resources (a bio-platform molecule). Initially, we tested the oxidation of glycerol in the liquid-phase, with hydrogen peroxide and TS-1. However, results achieved were not satisfactory. Then we investigated the gas-phase transformation of glycerol into acrylic acid, with the intermediate formation of acrolein; the latter can be obtained by dehydration of glycerol, and then can be oxidized into acrylic acid. Actually, the oxidation step from acrolein to acrylic acid is already optimized at an industrial level; therefore, we decided to investigate in depth the first step of the process. I studied the reactivity of heterogeneous acid catalysts based on sulphated zirconia. Tests were carried out both in aerobic and anaerobic conditions, in order to investigate the effect of oxygen on the catalyst deactivation rate (one main problem usually met in glycerol dehydration). Finally, I studied the reactivity of bifunctional systems, made of Keggin-type polyoxometalates, either alone or supported over sulphated zirconia, in this way combining the acid functionality (necessary for the dehydrative step) with the redox one (necessary for the oxidative step). In conclusion, during my PhD work I investigated reactions that apply the “green chemistry” rules and strategies; in particular, I studied new greener approaches for the synthesis of chemicals (Part A and Part B), the optimisation of reaction parameters to make the oxidation process more flexible (Part C), and the use of a bioplatform molecule for the synthesis of a chemical intermediate (Part D).