Monte Carlo Simulations of Novel Scintillator Detectors and Dosimetry Calculations

Monte Carlo (MC) simulation techniques are becoming very common in the Medical Physicists community. MC can be used for modeling Single Photon Emission Computed Tomography (SPECT) and for dosimetry calculations. 188Re, is a promising candidate for radiotherapeutic production and understanding the mechanisms of the radioresponse of tumor cells "in vitro" is of crucial importance as a first step before "in vivo" studies. The dosimetry of 188Re, used to target different lines of cancer cells, has been evaluated by the MC code GEANT4. The simulations estimate the average energy deposition/per event in the biological samples. The development of prototypes for medical imaging, based on LaBr3:Ce scintillation crystals coupled with a position sensitive photomultiplier, have been studied using GEANT4 simulations. Having tested, in the simulation, surface treatments different from the one applied to the crystal used in our experimental measurements, we found out that the Energy Resolution (ER) and the Spatial Resolution (SR) could be improved, in principle, by machining in a different way the lateral surfaces of the crystal. We have then studied a system able to acquire both echographic and scintigraphic images to let the medical operator obtain the complete anatomic and functional information for tumor diagnosis. The scintigraphic part of the detector is simulated by GEANT4 and first attempts to reconstruct tomographic images have been made using as method of reconstruction a back-projection standard algorithm. The proposed camera is based on slant collimators and LaBr3:Ce crystals. Within the Field of View (FOV) of the camera, it possible to distinguish point sources located in air at a distance of about 2 cm from each other. In particular conditions of uptake, tumor depth and dimension, the preliminary results show that the Signal to Noise Ratio (SNR) values obtained are higher than the standard detection limit.

Cesare Garboli traduttore di Measure for Measure di Shaskespeare per le compagnie di Luca Ronconi e di Carlo Cecchi

La tesi si occupa della traduzione di Measure for Measure di Shakespeare scritta da Cesare Garboli e pubblicata nel 1992 con Einaudi nella collana «Scrittori tradotti da scrittori». La traduzione fu concepita per il Teatro Stabile di Torino diretto da Luca Ronconi, che debuttò al teatro Carignano nel 1992 e venne successivamente ripresa, con alcune varianti, dalla compagnia di Carlo Cecchi nel 1998, per una nuova messinscena al teatro Garibaldi di Palermo. A partire dagli esiti più recenti dei Translation Studies, il lavoro sviluppa uno studio comparato, dal punto di vista linguistico e sotto il profilo ermeneutico, fra la traduzione di Garboli, il testo originale nelle due edizioni Arden e Cambridge e le traduzioni italiane di Measure for Measure pubblicate nel Novecento. La parte finale della tesi è dedicata alle messinscene a Torino e a Palermo: un confronto per evidenziare gli elementi che in entrambe appartengono alla strutturazione del testo tradotto e i caratteri specifici degli universi di finzione raffigurati dai due registi.

Local Earthquake Tomography by trans-dimensional Monte Carlo Sampling

In this study a new, fully non-linear, approach to Local Earthquake Tomography is presented. Local Earthquakes Tomography (LET) is a non-linear inversion problem that allows the joint determination of earthquakes parameters and velocity structure from arrival times of waves generated by local sources. Since the early developments of seismic tomography several inversion methods have been developed to solve this problem in a linearized way. In the framework of Monte Carlo sampling, we developed a new code based on the Reversible Jump Markov Chain Monte Carlo sampling method (Rj-McMc). It is a trans-dimensional approach in which the number of unknowns, and thus the model parameterization, is treated as one of the unknowns. I show that our new code allows overcoming major limitations of linearized tomography, opening a new perspective in seismic imaging. Synthetic tests demonstrate that our algorithm is able to produce a robust and reliable tomography without the need to make subjective a-priori assumptions about starting models and parameterization. Moreover it provides a more accurate estimate of uncertainties about the model parameters. Therefore, it is very suitable for investigating the velocity structure in regions that lack of accurate a-priori information. Synthetic tests also reveal that the lack of any regularization constraints allows extracting more information from the observed data and that the velocity structure can be detected also in regions where the density of rays is low and standard linearized codes fails. I also present high-resolution Vp and Vp/Vs models in two widespread investigated regions: the Parkfield segment of the San Andreas Fault (California, USA) and the area around the Alto Tiberina fault (Umbria-Marche, Italy). In both the cases, the models obtained with our code show a substantial improvement in the data fit, if compared with the models obtained from the same data set with the linearized inversion codes.

The XENON1T experiment: Monte Carlo background estimation and sensitivity curves study

Despite the scientific achievement of the last decades in the astrophysical and cosmological fields, the majority of the Universe energy content is still unknown. A potential solution to the “missing mass problem” is the existence of dark matter in the form of WIMPs. Due to the very small cross section for WIMP-nuleon interactions, the number of expected events is very limited (about 1 ev/tonne/year), thus requiring detectors with large target mass and low background level. The aim of the XENON1T experiment, the first tonne-scale LXe based detector, is to be sensitive to WIMP-nucleon cross section as low as 10^-47 cm^2. To investigate the possibility of such a detector to reach its goal, Monte Carlo simulations are mandatory to estimate the background. To this aim, the GEANT4 toolkit has been used to implement the detector geometry and to simulate the decays from the various background sources: electromagnetic and nuclear. From the analysis of the simulations, the level of background has been found totally acceptable for the experiment purposes: about 1 background event in a 2 tonne-years exposure. Indeed, using the Maximum Gap method, the XENON1T sensitivity has been evaluated and the minimum for the WIMP-nucleon cross sections has been found at 1.87 x 10^-47 cm^2, at 90% CL, for a WIMP mass of 45 GeV/c^2. The results have been independently cross checked by using the Likelihood Ratio method that confirmed such results with an agreement within less than a factor two. Such a result is completely acceptable considering the intrinsic differences between the two statistical methods. Thus, in the PhD thesis it has been proven that the XENON1T detector will be able to reach the designed sensitivity, thus lowering the limits on the WIMP-nucleon cross section by about 2 orders of magnitude with respect to the current experiments.

Città e architettura a Faenza nel Rinascimento. Progetti e strategie di rinnovamento urbano nell'età di Carlo II Manfredi (1468-77)

La tesi ha come oggetto il rinnovamento urbano che fu realizzato a Faenza per opera del suo signore Carlo II Manfredi tra il 1468 e il 1477, d’accordo con il fratello, il vescovo Federico. La prima opera realizzata da Carlo fu il portico a due livelli che dotò di una nuova facciata il suo palazzo di residenza, di origini medievali. Questa architettura sarebbe stata il preludio di un riordino generale della piazza principale della città, probabilmente allo scopo di ricreare un foro all’antica, come prescritto dai trattati di Vitruvio e di Alberti. L’aspetto originale del loggiato rinascimentale, desumibile da documentazione archivistica e iconografica, permette di attribuirlo con una certa probabilità a Giuliano da Maiano. Oltre alla piazza, Carlo riformò profondamente il tessuto urbano, demolendo molti portici lignei di origine medievale, rettificando le principali strade, completando la cerchia muraria. Federico Manfredi nel 1474 diede inizio alla fabbrica della Cattedrale, ricostruita dalle fondamenta su progetto dello stesso Giuliano da Maiano. L’architettura della chiesa ha uno stile largamente debitore all’architettura sacra di Brunelleschi, ma con significative differenze (come la navata definita da un’alternanza tra pilastri e colonne, o la copertura composta da volte a vela). L’abside della cattedrale, estranea al progetto maianesco, fu realizzata nel 1491-92 e mostra alcuni dettagli riconducibili alla coeva architettura di Bramante. A Faenza si realizza in un periodo di tempo brevissimo una profonda trasformazione del volto della città: loggiato, riforma della piazza, riordino delle strade, una nuova cattedrale, tutto contribuisce a dare lustro ai Manfredi e a fare di Faenza una città moderna e in cui si mettono in pratica, forse per la prima volta nell’Italia settentrionale, i dettami di Vitruvio e di Alberti.