MCAO for Extremely Large Telescopes: the cases of LBT and E-ELT

Several MCAO systems are under study to improve the angular resolution of the current and of the future generation large ground-based telescopes (diameters in the 8-40 m range). The subject of this PhD Thesis is embedded in this context. Two MCAO systems, in dierent realization phases, are addressed in this Thesis: NIRVANA, the 'double' MCAO system designed for one of the interferometric instruments of LBT, is in the integration and testing phase; MAORY, the future E-ELT MCAO module, is under preliminary study. These two systems takle the sky coverage problem in two dierent ways. The layer oriented approach of NIRVANA, coupled with multi-pyramids wavefront sensors, takes advantage of the optical co-addition of the signal coming from up to 12 NGS in a annular 2' to 6' technical FoV and up to 8 in the central 2' FoV. Summing the light coming from many natural sources permits to increase the limiting magnitude of the single NGS and to improve considerably the sky coverage. One of the two Wavefront Sensors for the mid- high altitude atmosphere analysis has been integrated and tested as a stand- alone unit in the laboratory at INAF-Osservatorio Astronomico di Bologna and afterwards delivered to the MPIA laboratories in Heidelberg, where was integrated and aligned to the post-focal optical relay of one LINC-NIRVANA arm. A number of tests were performed in order to characterize and optimize the system functionalities and performance. A report about this work is presented in Chapter 2. In the MAORY case, to ensure correction uniformity and sky coverage, the LGS-based approach is the current baseline. However, since the Sodium layer is approximately 10 km thick, the articial reference source looks elongated, especially when observed from the edge of a large aperture. On a 30-40 m class telescope, for instance, the maximum elongation varies between few arcsec and 10 arcsec, depending on the actual telescope diameter, on the Sodium layer properties and on the laser launcher position. The centroiding error in a Shack-Hartmann WFS increases proportionally to the elongation (in a photon noise dominated regime), strongly limiting the performance. To compensate for this effect a straightforward solution is to increase the laser power, i.e. to increase the number of detected photons per subaperture. The scope of Chapter 3 is twofold: an analysis of the performance of three dierent algorithms (Weighted Center of Gravity, Correlation and Quad-cell) for the instantaneous LGS image position measurement in presence of elongated spots and the determination of the required number of photons to achieve a certain average wavefront error over the telescope aperture. An alternative optical solution to the spot elongation problem is proposed in Section 3.4. Starting from the considerations presented in Chapter 3, a first order analysis of the LGS WFS for MAORY (number of subapertures, number of detected photons per subaperture, RON, focal plane sampling, subaperture FoV) is the subject of Chapter 4. An LGS WFS laboratory prototype was designed to reproduce the relevant aspects of an LGS SH WFS for the E-ELT and to evaluate the performance of different centroid algorithms in presence of elongated spots as investigated numerically and analytically in Chapter 3. This prototype permits to simulate realistic Sodium proles. A full testing plan for the prototype is set in Chapter 4.

Hybrid constraint programming and metaheuristic methods for large scale optimization problems

This work presents hybrid Constraint Programming (CP) and metaheuristic methods for the solution of Large Scale Optimization Problems; it aims at integrating concepts and mechanisms from the metaheuristic methods to a CP-based tree search environment in order to exploit the advantages of both approaches. The modeling and solution of large scale combinatorial optimization problem is a topic which has arisen the interest of many researcherers in the Operations Research field; combinatorial optimization problems are widely spread in everyday life and the need of solving difficult problems is more and more urgent. Metaheuristic techniques have been developed in the last decades to effectively handle the approximate solution of combinatorial optimization problems; we will examine metaheuristics in detail, focusing on the common aspects of different techniques. Each metaheuristic approach possesses its own peculiarities in designing and guiding the solution process; our work aims at recognizing components which can be extracted from metaheuristic methods and re-used in different contexts. In particular we focus on the possibility of porting metaheuristic elements to constraint programming based environments, as constraint programming is able to deal with feasibility issues of optimization problems in a very effective manner. Moreover, CP offers a general paradigm which allows to easily model any type of problem and solve it with a problem-independent framework, differently from local search and metaheuristic methods which are highly problem specific. In this work we describe the implementation of the Local Branching framework, originally developed for Mixed Integer Programming, in a CP-based environment. Constraint programming specific features are used to ease the search process, still mantaining an absolute generality of the approach. We also propose a search strategy called Sliced Neighborhood Search, SNS, that iteratively explores slices of large neighborhoods of an incumbent solution by performing CP-based tree search and encloses concepts from metaheuristic techniques. SNS can be used as a stand alone search strategy, but it can alternatively be embedded in existing strategies as intensification and diversification mechanism. In particular we show its integration within the CP-based local branching. We provide an extensive experimental evaluation of the proposed approaches on instances of the Asymmetric Traveling Salesman Problem and of the Asymmetric Traveling Salesman Problem with Time Windows. The proposed approaches achieve good results on practical size problem, thus demonstrating the benefit of integrating metaheuristic concepts in CP-based frameworks.

Componentistica avanzata per Impianti di Combustione a Biomassa

In un quadro internazionale di forte interesse verso uno sviluppo sostenibile e sfide energetiche per il futuro, il DIEM, in collaborazione con altri istituti di ricerca ed imprese private, sta progettando l’integrazione di componentistica avanzata su di una caldaia alimentata a biomasse. Lo scopo finale è quello di realizzare una caldaia a biomasse che produca energia in maniera più efficiente e con un impatto ambientale ridotto. L’applicazione è indirizzata inizialmente verso caldaie di piccola-media taglia (fino a 350 kW termici) vista la larga diffusione di questa tipologia di impianto. La componentistica in oggetto è: - filtro sperimentale ad alta efficienza per la rimozione del particolato; - celle a effetto Seebeck per la produzione di energia elettrica direttamente da energia termica senza parti meccaniche in movimento; - pompa Ogden per la produzione di energia meccanica direttamente da energia termica; La finalità dell’attività di ricerca è la progettazione dell’integrazione dei suddetti dispositivi con una caldaia a biomassa da 290 kW termici per la realizzazione di un prototipo di caldaia stand-alone ad impatto ambientale ridotto: in particolare, la caldaia è in grado, una volta raggiunte le condizioni di regime, di autoalimentare le proprie utenze elettriche, garantendo il funzionamento in sicurezza in caso di black-out o consentendo l’installazione della caldaia medesima in zone remote e prive di allaccio alla rete elettrica. Inoltre, la caldaia può fornire, tramite l'utilizzo di una pompa a vapore o pompa Ogden, energia meccanica per il pompaggio di fluidi: tale opportunità si ritiene particolarmente interessante per l'integrazione della caldaia nel caso di installazione in ambito agricolo. Infine, l'abbinamento di un filtro ad alta efficienza e basso costo consente l'abbattimento delle emissioni inquinanti, favorendo una maggiore diffusione della tecnologia senza ulteriori impatti sull'ambiente.

Advanced CMOS Interfaces for Bio-Nanosensors

The improvement of devices provided by Nanotechnology has put forward new classes of sensors, called bio-nanosensors, which are very promising for the detection of biochemical molecules in a large variety of applications. Their use in lab-on-a-chip could gives rise to new opportunities in many fields, from health-care and bio-warfare to environmental and high-throughput screening for pharmaceutical industry. Bio-nanosensors have great advantages in terms of cost, performance, and parallelization. Indeed, they require very low quantities of reagents and improve the overall signal-to-noise-ratio due to increase of binding signal variations vs. area and reduction of stray capacitances. Additionally, they give rise to new challenges, such as the need to design high-performance low-noise integrated electronic interfaces. This thesis is related to the design of high-performance advanced CMOS interfaces for electrochemical bio-nanosensors. The main focus of the thesis is: 1) critical analysis of noise in sensing interfaces, 2) devising new techniques for noise reduction in discrete-time approaches, 3) developing new architectures for low-noise, low-power sensing interfaces. The manuscript reports a multi-project activity focusing on low-noise design and presents two developed integrated circuits (ICs) as examples of advanced CMOS interfaces for bio-nanosensors. The first project concerns low-noise current-sensing interface for DC and transient measurements of electrophysiological signals. The focus of this research activity is on the noise optimization of the electronic interface. A new noise reduction technique has been developed so as to realize an integrated CMOS interfaces with performance comparable with state-of-the-art instrumentations. The second project intends to realize a stand-alone, high-accuracy electrochemical impedance spectroscopy interface. The system is tailored for conductivity-temperature-depth sensors in environmental applications, as well as for bio-nanosensors. It is based on a band-pass delta-sigma technique and combines low-noise performance with low-power requirements.

Oswald Mathias Ungers: Belvederestraße 60. Zu einer neuen Archtektur.

La presente Tesi di Dottorato intende affrontare una lettura critica della Casa in Belvederestraße 60, realizzata dall’architetto Oswald Mathias Ungers (Kaisersesch, 12 luglio 1926 – Köln, 30 settembre 2007), nel 1958-’59 a Köln-Müngersdorf, come studio per sé ed abitazione per la propria famiglia. Questo primo oggetto della ricerca viene considerato evidente espressione delle convinzioni formali e compositive dell’architetto, negli anni Cinquanta e Sessanta. A differenza di altri progetti residenziali coevi ed antecedenti, frutto di un’elaborazione autonoma, la prima casa che costruisce per sé riflette una maggiore libertà di pensiero, dettata dalla coincidenza delle figure di progettista e committente; a ciò si aggiunge anche una precisa volontà dichiarativa ed ideologica. Proprio quest’ultimo aspetto permette di introdurre il secondo oggetto della Tesi: il manifesto “ideologico”, Zu einer neuen Architektur, scritto dallo stesso Oswald Mathias Ungers e da Reinhard Gieselmann, alla fine del 1960; un breve testo che espone, con toni perentori ed inappellabili, il punto di vista dei due architetti nei confronti di un panorama architettonico e critico, caratterizzato da una sterilità di pensiero dilagante, a causa dell’egemonia costruttiva funzionalista. La ricerca indaga quindi le forti reciprocità delle due opere: casa e testo, viste in chiave di “manifesto scritto e manifesto costruito”. Il primo legame tra i due soggetti è senza dubbio la concomitanza temporale, (tra il 1958 ed il 1960) associata ad un rapporto causa-effetto, tale per cui il manifesto viene redatto a difesa delle aspre critiche scaturite dalla pubblicazione della casa sulla rivista Bauwelt. Il secondo nesso è la possibilità di comprendere le accezioni effettive dei termini impiegati nella redazione del testo, attraverso le forme di una delle opere maggiormente personali dell’architetto, estraendone il senso e conferendogli un’immagine architettonica. Si vuole creare così un rapporto biunivoco di traducibilità, dell’architettura nello scritto e della semantica ungersiana in azioni compositive.

Management Perspectives on Industrial Heritage: an Exploratory Research

The current research project focuses on the analysis of the critical issues of industrial heritage management in Italy and the preservation of organizational history within the reuse projects of former industrial sites. The organizational and managerial perspective is crucial on two levels. Firstly, it is important in the analysis of the original significance of the site, and in particular its organizational history, and its conservation within the new regeneration strategy. Secondly, it is crucial at the phase of management of reuse projects and its feasibility and sustainability analysis. Based on the analysis of the literature, a unique classification of the reuse strategies that can be implemented in order to regenerate former industrial sites has been formulated. The exploratory research thus adapts a multiple case study design. Eight Italian case studies have been chosen, one for each type of regeneration strategy. Each case study is explored as a stand-alone entity through the analysis of the local differences and idiosyncrasies of the specific context, the factors that stood behind the choice of the reuse strategy and the way the reuse project evolved through the years. Then, the current management of each reuse project is analysed. The narration and musealization of the organizational history is investigated through the spatial dimension, the level of content and the level of expression. Secondly, the case studies are compared through a cross-case analysis from three different perspectives: issues on the phase of preparation and implementation of the reuse projects, critical issues behind the current management of new projects and issues on the ways of preservation and narration of organizational history within the new project. The research shows that all regeneration strategies are affected by the conflict between preservation and change, by the issue of materiality and selectivity.

Lo studio del microclima indoor per la conservazione preventiva del Patrimonio storico artistico e culturale

La conservazione preventiva degli edifici storici e dei beni custoditi al loro interno rappresenta una sfida ad oggi condivisa a livello internazionale. Tale conservazione dipende da numerose variabili, tra le quali il microclima indoor gioca un ruolo decisivo. Il fine di questa tesi è verificare come lo studio del microclima indoor, supportato dalla simulazione virtuale e dalla conoscenza storica delle evoluzioni dell’edificio stesso (legate a modifiche impiantistiche; architettoniche; d’uso; ecc., nel corso degli anni), costituiscano una base conoscitiva fondamentale, da cui architetti e restauratori possono partire per definire strategie specifiche, volte alla conservazione preventiva del Patrimonio. Per fare questo, l’autore presenta le indagini svolte per tre casi-studio: la Sala 33 della Reggia di Venaria Reale, in provincia di Torino, Italia; la Biblioteca Generale Storica dell’Università di Salamanca, in Spagna; il Portico della Gloria, nartece della Cattedrale di Santiago de Compostela, in Spagna. La metodologia definita e adottata per l’analisi e l’interpretazione dei dati di ciascun caso-studio ha previsto la comprensione e la messa in relazione tra: scelte costruttive; vicende evolutive delle singole architetture; fattori che ne determinano il microclima, letti (o ipotizzati) nelle relative modifiche diacroniche; degrado delle architetture e dei beni che sono custoditi in esse. Infine, uno degli esiti più innovativi della ricerca è stata la definizione di due indici di rischio: sono stati infatti definiti due nuovi indici (Heritage Microclimate Risk -HMR- e Predicted Risk of Damage -PRD-) legati al microclima degli edifici che ospitano beni e manufatti che costituiscono il patrimonio storico artistico e culturale. Tali indici sono stati definiti tenendo conto di tutte le variabili da cui il microclima dipende e dei fattori che ne determinano l’evolversi nel tempo e nello spazio.

Percutaneous Cement Discoplasty: Biomechanical and clinical assessment of a minimally invasive treatment of lumbar intervertebral disc disease

With population ageing, spine diseases have an increasing prevalence and induce high economic and social costs. The development of minimally invasive surgeries allows reducing the surgery-associated risks in elderly and polymorbid patients, and save costs by treating more patients in shorter time and reducing the complications. Percutaneous Cement Discoplasty (PCD) is a minimally invasive technique developed to treat highly degenerated intervertebral discs exhibiting a vacuum phenomenon. Filling the disc with bone cement creates a stand-alone spacer which partially restores the disc height and re-opens the foraminal space. PCD has recently been introduced to clinical use. However, the spine biomechanics following this treatment remained unravelled. The aim of this PhD thesis is to bridge the clinical experience with in vitro methodologies, to provide a multilateral evaluation of PCD outcome and a better understanding of its impact on the spine biomechanics, and of its possible contraindications. Firstly, a suitable in vitro porcine model to test the biomechanics of discoplasty by comparing specimens in the preoperative and postoperative conditions was developed. The methodology was then applied to investigate the biomechanics of discoplasty in cadaveric human segments. The in vitro specimens were mechanically investigated in flexion and extension, while a DIC system quantified the range of motion, disc height, and strains on the disc surface. Then, a versatile tool to measure the impact of discoplasty on the foramen space was developed and applied both to clinical and experimental work. The vertebrae reconstructed from CT scans were registered to match the loading configuration, using ex vivo DIC measurements under loading. The foramen volumetric changes caused by PCD was measured using a 3D geometrical method clinically developed by the research group. In conclusion, this project significantly extended the understanding of PCD biomechanics, highlighting its benefits in the treatment of advanced cases of intervertebral disc degeneration.

Deep space orbit determination and guidance of the LICIACube microsatellite mission

Recently, the JPL's MarCO mission demonstrated that these probes are also mature enough to be employed in the deep space, even though with the limitations related to the employed commercial components. Currently, other deep space CubeSats are planned either as stand-alone missions or as companions of a traditional large probe. Therefore, developing a dedicated navigation suite is crucial to reaching the mission's goals, considering the limitations of the onboard components compared to typical deep space missions. In this framework, the LICIACube mission represents an ideal candidate test-bench, as it performs a flyby of the Didymos asteroid system subject to a strong position, epochs, and pointing requirements. This mission will also allow us to infer the capabilities of such microsatellites and highlight their limitations compared with the benefits of a lighter design and tailoring efforts. In this work, the OD and guidance methods and tools adopted for classical deep space missions have been tailored for the CubeSat applications and validated through extensive analyses. In addition, navigation procedures and interfaces have been designed in view of the operations foreseen in late 2022. The pre-launch covariance analysis has been performed to assess the mission's feasibility for the nominal trajectory and its associated uncertainties, based on conservative assumptions on the main parameters. Extensive sensitivity analyses have been carried out to understand the main mission parameters affecting the performance and to demonstrate the robustness of the designed trajectory and operation schedule in fulfilling the mission requirements. The developed system was also stressed by tuning the models to access different reconstruction methods for the maneuvers. The analysis demonstrated the feasibility of the LICIACube mission navigation in compliance with the mission requirements, compatible with the limited resources available, both in space and on the ground.