Comparison of affinity chromatography supports for separation of protein

Chromatography is the most widely used technique for high-resolution separation and analysis of proteins. This technique is very useful for the purification of delicate compounds, e.g. pharmaceuticals, because it is usually performed at milder conditions than separation processes typically used by chemical industry. This thesis focuses on affinity chromatography. Chromatographic processes are traditionally performed using columns packed with porous resin. However, these supports have several limitations, including the dependence on intra-particle diffusion, a slow mass transfer mechanism, for the transport of solute molecules to the binding sites within the pores and high pressure drop through the packed bed. These limitations can be overcome by using chromatographic supports like membranes or monoliths. Dye-ligands are considered important alternatives to natural ligands. Several reactive dyes, particularly Cibacron Blue F3GA, are used as affinity ligand for protein purification. Cibacron Blue F3GA is a triazine dye that interacts specifically and reversibly with albumin. The aim of this study is to prepare dye-affinity membranes and monoliths for efficient removal of albumin and to compare the three different affinity supports: membranes and monoliths and a commercial column HiTrapTM Blue HP, produced by GE Healthcare. A comparison among the three supports was performed in terms of binding capacity at saturation (DBC100%) and dynamic binding capacity at 10% breakthrough (DBC10%) using solutions of pure BSA. The results obtained show that the CB-RC membranes and CB-Epoxy monoliths can be compared to commercial support, column HiTrapTM Blue HP, for the separation of albumin. These results encourage a further characterization of the new supports examined.

Climate change and the tourism sector: the clean development mechanism, a market instrument under the Kyoto Protocol to achieve multiple objectives

The main objective of this research is to demonstrate that the Clean Development Mechanism (CDM), an instrument created under a global international treaty, can achieve multiple objectives beyond those for which it has been established. As such, while being already a powerful tool to contribute to the global fight against climate change, the CDM can also be successful if applied to different sectors not contemplated before. In particular, this research aimed at demonstrating that a wider utilization of the CDM in the tourism sector can represent an innovative way to foster sustainable tourism and generate additional benefits. The CDM was created by Article 12 of the Kyoto Protocol of the United Nations Framework Convention on Climate Change (UNFCCC) and represents an innovative tool to reduce greenhouse gases emissions through the implementation of mitigation activities in developing countries which generate certified emission reductions (CERs), each of them equivalent to one ton of CO2 not emitted in the atmosphere. These credits can be used for compliance reasons by industrialized countries in achieving their reduction targets. The logic path of this research begins with an analysis of the scientific evidences of climate change and its impacts on different economic sectors including tourism and it continues with a focus on the linkages between climate and the tourism sector. Then, it analyses the international responses to the issue of climate change and the peculiar activities in the international arena addressing climate change and the tourism sector. The concluding part of the work presents the objectives and achievements of the CDM and its links to the tourism sector by considering case studies of existing projects which demonstrate that the underlying question can be positively answered. New opportunities for the tourism sector are available.

The assessment of change in rural landscape and the analysis of the driving forces. Proposal of a spatial model for the rural built environment

The presented study carried out an analysis on rural landscape changes. In particular the study focuses on the understanding of driving forces acting on the rural built environment using a statistical spatial model implemented through GIS techniques. It is well known that the study of landscape changes is essential for a conscious decision making in land planning. From a bibliography review results a general lack of studies dealing with the modeling of rural built environment and hence a theoretical modelling approach for such purpose is needed. The advancement in technology and modernity in building construction and agriculture have gradually changed the rural built environment. In addition, the phenomenon of urbanization of a determined the construction of new volumes that occurred beside abandoned or derelict rural buildings. Consequently there are two types of transformation dynamics affecting mainly the rural built environment that can be observed: the conversion of rural buildings and the increasing of building numbers. It is the specific aim of the presented study to propose a methodology for the development of a spatial model that allows the identification of driving forces that acted on the behaviours of the building allocation. In fact one of the most concerning dynamic nowadays is related to an irrational expansion of buildings sprawl across landscape. The proposed methodology is composed by some conceptual steps that cover different aspects related to the development of a spatial model: the selection of a response variable that better describe the phenomenon under study, the identification of possible driving forces, the sampling methodology concerning the collection of data, the most suitable algorithm to be adopted in relation to statistical theory and method used, the calibration process and evaluation of the model. A different combination of factors in various parts of the territory generated favourable or less favourable conditions for the building allocation and the existence of buildings represents the evidence of such optimum. Conversely the absence of buildings expresses a combination of agents which is not suitable for building allocation. Presence or absence of buildings can be adopted as indicators of such driving conditions, since they represent the expression of the action of driving forces in the land suitability sorting process. The existence of correlation between site selection and hypothetical driving forces, evaluated by means of modeling techniques, provides an evidence of which driving forces are involved in the allocation dynamic and an insight on their level of influence into the process. GIS software by means of spatial analysis tools allows to associate the concept of presence and absence with point futures generating a point process. Presence or absence of buildings at some site locations represent the expression of these driving factors interaction. In case of presences, points represent locations of real existing buildings, conversely absences represent locations were buildings are not existent and so they are generated by a stochastic mechanism. Possible driving forces are selected and the existence of a causal relationship with building allocations is assessed through a spatial model. The adoption of empirical statistical models provides a mechanism for the explanatory variable analysis and for the identification of key driving variables behind the site selection process for new building allocation. The model developed by following the methodology is applied to a case study to test the validity of the methodology. In particular the study area for the testing of the methodology is represented by the New District of Imola characterized by a prevailing agricultural production vocation and were transformation dynamic intensively occurred. The development of the model involved the identification of predictive variables (related to geomorphologic, socio-economic, structural and infrastructural systems of landscape) capable of representing the driving forces responsible for landscape changes.. The calibration of the model is carried out referring to spatial data regarding the periurban and rural area of the study area within the 1975-2005 time period by means of Generalised linear model. The resulting output from the model fit is continuous grid surface where cells assume values ranged from 0 to 1 of probability of building occurrences along the rural and periurban area of the study area. Hence the response variable assesses the changes in the rural built environment occurred in such time interval and is correlated to the selected explanatory variables by means of a generalized linear model using logistic regression. Comparing the probability map obtained from the model to the actual rural building distribution in 2005, the interpretation capability of the model can be evaluated. The proposed model can be also applied to the interpretation of trends which occurred in other study areas, and also referring to different time intervals, depending on the availability of data. The use of suitable data in terms of time, information, and spatial resolution and the costs related to data acquisition, pre-processing, and survey are among the most critical aspects of model implementation. Future in-depth studies can focus on using the proposed model to predict short/medium-range future scenarios for the rural built environment distribution in the study area. In order to predict future scenarios it is necessary to assume that the driving forces do not change and that their levels of influence within the model are not far from those assessed for the time interval used for the calibration.

Diagnostic techniques for EHD and MHD interaction

The impact of plasma technologies is growing both in the academic and in the industrial fields. Nowadays, a great interest is focused in plasma applications in aeronautics and astronautics domains. Plasma actuators based on the Magneto-Hydro-Dynamic (MHD) and Electro- Hydro-Dynamic (EHD) interactions are potentially able to suitably modify the fluid-dynamics characteristics around a flying body without utilizing moving parts. This could lead to the control of an aircraft with negligible response time, more reliability and improvements of the performance. In order to study the aforementioned interactions, a series of experiments and a wide number of diagnostic techniques have been utilized. The EHD interaction, realized by means of a Dielectric Barrier Discharge (DBD) actuator, and its impact on the boundary layer have been evaluated by means of two different experiments. In the first one a three phase multi-electrode flat panel actuator is used. Different external flow velocities (from 1 to 20m/s) and different values of the supplied voltage and frequency have been considered. Moreover a change of the phase sequence has been done to verify the influence of the electric field existing between successive phases. Measurements of the induced speed had shown the effect of the supply voltage and the frequency, and the phase order in the momentum transfer phenomenon. Gains in velocity, inside the boundary layer, of about 5m/s have been obtained. Spectroscopic measurements allowed to determine the rotational and the vibrational temperature of the plasma which lie in the range of 320 ÷ 440°K and of 3000 ÷ 3900°K respectively. A deviation from thermodynamic equilibrium had been found. The second EHD experiment is realized on a single electrode pair DBD actuator driven by nano-pulses superimposed to a DC or an AC bias. This new supply system separates the plasma formation mechanism from the acceleration action on the fluid, leading to an higher degree of the control of the process. Both the voltage and the frequency of the nano-pulses and the amplitude and the waveform of the bias have been varied during the experiment. Plasma jets and vortex behavior had been observed by means of fast Schlieren imaging. This allowed a deeper understanding of the EHD interaction process. A velocity increase in the boundary layer of about 2m/s had been measured. Thrust measurements have been performed by means of a scales and compared with experimental data reported in the literature. For similar voltage amplitudes thrust larger than those of the literature, had been observed. Surface charge measurements led to realize a modified DBD actuator able to obtain similar performances when compared with that of other experiments. However in this case a DC bias replacing the AC bias had been used. MHD interaction experiments had been carried out in a hypersonic wind tunnel in argon with a flow of Mach 6. Before the MHD experiments a thermal, fluid-dynamic and plasma characterization of the hypersonic argon plasma flow have been done. The electron temperature and the electron number density had been determined by means of emission spectroscopy and microwave absorption measurements. A deviation from thermodynamic equilibrium had been observed. The electron number density showed to be frozen at the stagnation region condition in the expansion through the nozzle. MHD experiments have been performed using two axial symmetric test bodies. Similar magnetic configurations were used. Permanent magnets inserted into the test body allowed to generate inside the plasma azimuthal currents around the conical shape of the body. These Faraday currents are responsible of the MHD body force which acts against the flow. The MHD interaction process has been observed by means of fast imaging, pressure and electrical measurements. Images showed bright rings due to the Faraday currents heating and exciting the plasma particles. Pressure measurements showed increases of the pressure in the regions where the MHD interaction is large. The pressure is 10 to 15% larger than when the MHD interaction process is silent. Finally by means of electrostatic probes mounted flush on the test body lateral surface Hall fields of about 500V/m had been measured. These results have been used for the validation of a numerical MHD code.

Modificazioni soggettive del rapporto obbligatorio e garanzie reali

Lo studio del lato soggettivo del rapporto è centrale nella teoria dell’obbligazione. Ci si chiede se la modificazione di una o anche di entrambe le parti del rapporto determini sempre la sua estinzione o se, invece, si conservi la sua unitarietà oggettiva. La risposta a questo interrogativo è stata diversa a seconda delle diverse epoche storiche. Nel diritto romano si riteneva che la variazione di qualunque soggetto determinasse l’estinzione del rapporto e la costituzione di una nuova obbligazione (novazione soggettiva). Tale soluzione è stata osteggiata dai codificatori moderni per i quali, in caso di modifica delle personae non si ha estinzione del rapporto, ma solo il mutamento di uno dei suoi elementi. Quanto ai diritti di garanzia, in particolare l’ipoteca, i principi generali essenzali sono la specialità e l’accessorietà. Quest’ultima caratteristica è dirimente in caso di modificazione soggettiva del rapporto e ciò emerge in sede di trattazione delle singole fattispecie del Codice Civile che la determinano, sia quanto al creditore sia quanto al debitore. Per velocizzare il subentro nel credito, nel 2007 è stato approvato il decreto Bersani (sulla portabilità del mutuo) che ha consentito di rimuovere vincoli a tale circolazione, nell’ambito dei rapporti bancari. Le caratteristiche della modificazione del rapporto obbligatorio, tuttavia, possono minare l’efficacia della riforma Bersani. Questo è il motivo per il quale taluni studiosi ritengono necessario procedere a un’ampia rivisitazione dell’intero diritto ipotecario, eliminando, sulla scia di quanto accaduto in altri ordinamenti europei, il requisito dell’accessorietà del vincolo. Nonostante ciò, a causa dei rischi connessi a questa riforma, si ritiene preferibile affinare il meccanismo di perfezionamento della portabilità, eliminandone le criticità, senza però pregiudicare le sicurezze dell’attuale sistema giuridico, di cui l’accessorietà dell’ipoteca rispetto al credito costituisce un importante caposaldo.

From Folke Medicine to Medicine Chemistry: Study, Using in Vitro and Cellular Assays, of Receptors Mechanism Involved in the Activities of Natural Compounds

My Doctorate Research has been focused on the evaluation of the pharmacological activity of a natural extract of chestnut wood (ENC) towards the cardiovascular and gastrointestinal system and on the identification of the active compounds. The ENC has been shown to contain more than 10% (w/w) of phenolic compounds, of which tannins as Vescalgin and Castalgin are the more representative. ENC cardiovascular effects have been investigated in guinea pig cardiac preparations; furthermore its activity has been evalueted in guinea pig aorta strips. ENC induced transient negative chronotropic effect in isolated spontaneously beating right atria and simultaneously positive inotropic effect in left atria driven at 1 Hz. Cardiac cholinergic receptors are not involved in the negative chronotropic effect and positive inotropic effects are not related to adrenergic receptors. In vascular smooth muscle, natural extract of chestnut did not significantly change the contraction induced by potassium (80 mM) or that induced by noradrenaline (1μM). In guinea pig ileum, ENC reduced the maximum response to carbachol in a concentrationdependent manner and behaved as a reversible non competitive antagonist. In guinea pig ileum, the antispasmodic activity of ENC showed a significant antispasmodic activity against a variety of different spasmogenic agents including histamine, KCl, BaCl2. In guinea pig proximal colon, stomach and jejunum, ENC reduced the maximum response to carbachol in a concentrationdependent manner and behaved as a reversible non competitive antagonist. ENC contracted gallbladder guinea pig in a reversible and concentration-dependent manner. This effect does not involve cholinergic and cholecystokinin receptors and it is reduced by nifedipine. ENC relaxed Oddi sphincter smooth muscle. The cholecystokinetic and Oddi sphincter relaxing activities occurred also in guinea pigs fed a lithogenic diet. The cholecystokinetic occurred also in human gallbladder. The Fractionation of the extract led to the identification of the active fraction.

The Effectiveness of the Clean Development Mechanism – A law and economics analysis

Climate change has been acknowledged as a threat to humanity. Most scholars agree that to avert dangerous climate change and to transform economies into low-carbon societies, deep global emission reductions are required by the year 2050. Under the framework of the Kyoto Protocol, the Clean Development Mechanism (CDM) is the only market-based instrument that encourages industrialised countries to pursue emission reductions in developing countries. The CDM aims to pay the incremental finance necessary to operationalize emission reduction projects which are otherwise not financially viable. According to the objectives of the Kyoto Protocol, the CDM should finance projects that are additional to those which would have happened anyway, contribute to sustainable development in the countries hosting the projects, and be cost-effective. To enable the identification of such projects, an institutional framework has been established by the Kyoto Protocol which lays out responsibilities for public and private actors. This thesis examines whether the CDM has achieved these objectives in practice and can thus be considered an effective tool to reduce emissions. To complete this investigation, the book applies economic theory and analyses the CDM from two perspectives. The first perspective is the supply-dimension which answers the question of how, in practice, the CDM system identified additional, cost-effective, sustainable projects and, generated emission reductions. The main contribution of this book is the second perspective, the compliance-dimension, which answers the question of whether industrialised countries effectively used the CDM for compliance with their Kyoto targets. The application of the CDM in the European Union Emissions Trading Scheme (EU ETS) is used as a case-study. Where the analysis identifies inefficiencies within the supply or the compliance dimension, potential improvements of the legal framework are proposed and discussed.

Effects of temperature and acidity on Mediterranean benthic calcifiers, in the face of globale climate change

The Mediterranean Sea is expected to react faster to global change compared to the ocean and is already showing more pronounced warming and acidification rates. A study performed along the Italian western coast showed that porosity of the skeleton increases with temperature in the zooxanthellate (i.e. symbiotic with unicellular algae named zooxanthellae) solitary scleractinian Balanophyllia europaea while it does not vary with temperature in the solitary non-zooxanthellate Leptopsammia pruvoti. These results were confirmed by another study that indicated that the increase in porosity was accompanied by an increase of the fraction of the largest pores in the pore-space, perhaps due to an inhibition of the photosynthetic process at elevated temperatures, causing an attenuation of calcification. B. europaea, L. pruvoti and the colonial non-zooxanthellate Astroides calycularis, transplanted along a natural pH gradient, showed that high temperature exacerbated the negative effect of lowered pH on their mortality rates. The growth of the zooxanthellate species did not react to reduced pH, while the growth of the two non-zooxanthellate species was negatively affected. Reduced abundance of naturally occurring B. europaea, a mollusk, a calcifying and a non-calcifying macroalgae were observed along the gradient while no variation was seen in the abundance of a calcifying green alga. With decreasing pH, the mineralogy of the coral and mollusk did not change, while the two calcifying algae decreased the content of aragonite in favor of the less soluble calcium sulphates and whewellite (calcium oxalate), possibly as a mechanism of phenotypic plasticity. Increased values of porosity and macroporosity with CO2 were observed in B. europaea specimens, indicating reduces the resistance of its skeletons to mechanical stresses with increasing acidity. These findings, added to the negative effect of temperature on various biological parameters, generate concern on the sensitivity of this zooxanthellate species to the envisaged global climate change scenarios.