Asset management of wastewater networks

Asset Management (AM) is a set of procedures operable at the strategic-tacticaloperational level, for the management of the physical asset’s performance, associated risks and costs within its whole life-cycle. AM combines the engineering, managerial and informatics points of view. In addition to internal drivers, AM is driven by the demands of customers (social pull) and regulators (environmental mandates and economic considerations). AM can follow either a top-down or a bottom-up approach. Considering rehabilitation planning at the bottom-up level, the main issue would be to rehabilitate the right pipe at the right time with the right technique. Finding the right pipe may be possible and practicable, but determining the timeliness of the rehabilitation and the choice of the techniques adopted to rehabilitate is a bit abstruse. It is a truism that rehabilitating an asset too early is unwise, just as doing it late may have entailed extra expenses en route, in addition to the cost of the exercise of rehabilitation per se. One is confronted with a typical ‘Hamlet-isque dilemma’ – ‘to repair or not to repair’; or put in another way, ‘to replace or not to replace’. The decision in this case is governed by three factors, not necessarily interrelated – quality of customer service, costs and budget in the life cycle of the asset in question. The goal of replacement planning is to find the juncture in the asset’s life cycle where the cost of replacement is balanced by the rising maintenance costs and the declining level of service. System maintenance aims at improving performance and maintaining the asset in good working condition for as long as possible. Effective planning is used to target maintenance activities to meet these goals and minimize costly exigencies. The main objective of this dissertation is to develop a process-model for asset replacement planning. The aim of the model is to determine the optimal pipe replacement year by comparing, temporally, the annual operating and maintenance costs of the existing asset and the annuity of the investment in a new equivalent pipe, at the best market price. It is proposed that risk cost provide an appropriate framework to decide the balance between investment for replacing or operational expenditures for maintaining an asset. The model describes a practical approach to estimate when an asset should be replaced. A comprehensive list of criteria to be considered is outlined, the main criteria being a visà- vis between maintenance and replacement expenditures. The costs to maintain the assets should be described by a cost function related to the asset type, the risks to the safety of people and property owing to declining condition of asset, and the predicted frequency of failures. The cost functions reflect the condition of the existing asset at the time the decision to maintain or replace is taken: age, level of deterioration, risk of failure. The process model is applied in the wastewater network of Oslo, the capital city of Norway, and uses available real-world information to forecast life-cycle costs of maintenance and rehabilitation strategies and support infrastructure management decisions. The case study provides an insight into the various definitions of ‘asset lifetime’ – service life, economic life and physical life. The results recommend that one common value for lifetime should not be applied to the all the pipelines in the stock for investment planning in the long-term period; rather it would be wiser to define different values for different cohorts of pipelines to reduce the uncertainties associated with generalisations for simplification. It is envisaged that more criteria the municipality is able to include, to estimate maintenance costs for the existing assets, the more precise will the estimation of the expected service life be. The ability to include social costs enables to compute the asset life, not only based on its physical characterisation, but also on the sensitivity of network areas to social impact of failures. The type of economic analysis is very sensitive to model parameters that are difficult to determine accurately. The main value of this approach is the effort to demonstrate that it is possible to include, in decision-making, factors as the cost of the risk associated with a decline in level of performance, the level of this deterioration and the asset’s depreciation rate, without looking at age as the sole criterion for making decisions regarding replacements.

On the Efficiency of the Benchmarks Used in the Asset Management

In this work we studied the efficiency of the benchmarks used in the asset management industry. In chapter 2 we analyzed the efficiency of the benchmark used for the government bond markets. We found that for the Emerging Market Bonds an equally weighted index for the country weights is probably the more suited because guarantees maximum diversification of country risk but for the Eurozone government bond market we found a GDP weighted index is better because the most important matter is to avoid a higher weight for highly indebted countries. In chapter 3 we analyzed the efficiency of a Derivatives Index to invest in the European corporate bond market instead of a Cash Index. We can state that the two indexes are similar in terms of returns, but that the Derivatives Index is less risky because it has a lower volatility, has values of skewness and kurtosis closer to those of a normal distribution and is a more liquid instrument, as the autocorrelation is not significant. In chapter 4 it is analyzed the impact of fallen angels on the corporate bond portfolios. Our analysis investigated the impact of the month-end rebalancing of the ML Emu Non Financial Corporate Index for the exit of downgraded bond (the event). We can conclude a flexible approach to the month-end rebalancing is better in order to avoid a loss of valued due to the benchmark construction rules. In chapter 5 we did a comparison between the equally weighted and capitalization weighted method for the European equity market. The benefit which results from reweighting the portfolio into equal weights can be attributed to the fact that EW portfolios implicitly follow a contrarian investment strategy, because they mechanically rebalance away from stocks that increase in price.

L'efficienza degli indici azionari: un'analisi empirica

La studio dell’efficienza di un indice azionario ha accresciuto la propria importanza nell’industria dell’asset management a seguito della diffusione dell’utilizzo di benchmark e investimenti indicizzati. Il presente lavoro valuta il livello di efficienza dei principali indici del mercato azionario statunitense, dell’Area Euro e italiano. Lo studio empirico ricorre a quattro misure di efficienza: il GRS, un test small-sample multivariato fondato sul CAPM; il test large sample di Wald, implementato tramite una simulazione bootstrap; il test GMM, che è stato applicato in una cornice non-gaussiana attraverso una simulazione block bootstrap; la misura di efficienza relativa di Kandel e Stambaugh. I risultati empirici forniscono una prova evidente della superiore efficienza degli indici equiponderati. Questa conclusione è interpretata sulla base della letteratura scientifica esistente, analizzando le diverse cause di ordine teorico ed empirico che sono state proposte.

Tecniche per il controllo dinamico del consumo di potenza per piattaforme system-on-chip

Providing support for multimedia applications on low-power mobile devices remains a significant research challenge. This is primarily due to two reasons: • Portable mobile devices have modest sizes and weights, and therefore inadequate resources, low CPU processing power, reduced display capabilities, limited memory and battery lifetimes as compared to desktop and laptop systems. • On the other hand, multimedia applications tend to have distinctive QoS and processing requirementswhichmake themextremely resource-demanding. This innate conflict introduces key research challenges in the design of multimedia applications and device-level power optimization. Energy efficiency in this kind of platforms can be achieved only via a synergistic hardware and software approach. In fact, while System-on-Chips are more and more programmable thus providing functional flexibility, hardwareonly power reduction techniques cannot maintain consumption under acceptable bounds. It is well understood both in research and industry that system configuration andmanagement cannot be controlled efficiently only relying on low-level firmware and hardware drivers. In fact, at this level there is lack of information about user application activity and consequently about the impact of power management decision on QoS. Even though operating system support and integration is a requirement for effective performance and energy management, more effective and QoSsensitive power management is possible if power awareness and hardware configuration control strategies are tightly integratedwith domain-specificmiddleware services. The main objective of this PhD research has been the exploration and the integration of amiddleware-centric energymanagement with applications and operating-system. We choose to focus on the CPU-memory and the video subsystems, since they are the most power-hungry components of an embedded system. A second main objective has been the definition and implementation of software facilities (like toolkits, API, and run-time engines) in order to improve programmability and performance efficiency of such platforms. Enhancing energy efficiency and programmability ofmodernMulti-Processor System-on-Chips (MPSoCs) Consumer applications are characterized by tight time-to-market constraints and extreme cost sensitivity. The software that runs on modern embedded systems must be high performance, real time, and even more important low power. Although much progress has been made on these problems, much remains to be done. Multi-processor System-on-Chip (MPSoC) are increasingly popular platforms for high performance embedded applications. This leads to interesting challenges in software development since efficient software development is a major issue for MPSoc designers. An important step in deploying applications on multiprocessors is to allocate and schedule concurrent tasks to the processing and communication resources of the platform. The problem of allocating and scheduling precedenceconstrained tasks on processors in a distributed real-time system is NP-hard. There is a clear need for deployment technology that addresses thesemulti processing issues. This problem can be tackled by means of specific middleware which takes care of allocating and scheduling tasks on the different processing elements and which tries also to optimize the power consumption of the entire multiprocessor platform. This dissertation is an attempt to develop insight into efficient, flexible and optimalmethods for allocating and scheduling concurrent applications tomultiprocessor architectures. It is a well-known problem in literature: this kind of optimization problems are very complex even in much simplified variants, therefore most authors propose simplified models and heuristic approaches to solve it in reasonable time. Model simplification is often achieved by abstracting away platform implementation ”details”. As a result, optimization problems become more tractable, even reaching polynomial time complexity. Unfortunately, this approach creates an abstraction gap between the optimization model and the real HW-SW platform. The main issue with heuristic or, more in general, with incomplete search is that they introduce an optimality gap of unknown size. They provide very limited or no information on the distance between the best computed solution and the optimal one. The goal of this work is to address both abstraction and optimality gaps, formulating accurate models which accounts for a number of ”non-idealities” in real-life hardware platforms, developing novel mapping algorithms that deterministically find optimal solutions, and implementing software infrastructures required by developers to deploy applications for the targetMPSoC platforms. Energy Efficient LCDBacklightAutoregulation on Real-LifeMultimediaAp- plication Processor Despite the ever increasing advances in Liquid Crystal Display’s (LCD) technology, their power consumption is still one of the major limitations to the battery life of mobile appliances such as smart phones, portable media players, gaming and navigation devices. There is a clear trend towards the increase of LCD size to exploit the multimedia capabilities of portable devices that can receive and render high definition video and pictures. Multimedia applications running on these devices require LCD screen sizes of 2.2 to 3.5 inches andmore to display video sequences and pictures with the required quality. LCD power consumption is dependent on the backlight and pixel matrix driving circuits and is typically proportional to the panel area. As a result, the contribution is also likely to be considerable in future mobile appliances. To address this issue, companies are proposing low power technologies suitable for mobile applications supporting low power states and image control techniques. On the research side, several power saving schemes and algorithms can be found in literature. Some of them exploit software-only techniques to change the image content to reduce the power associated with the crystal polarization, some others are aimed at decreasing the backlight level while compensating the luminance reduction by compensating the user perceived quality degradation using pixel-by-pixel image processing algorithms. The major limitation of these techniques is that they rely on the CPU to perform pixel-based manipulations and their impact on CPU utilization and power consumption has not been assessed. This PhDdissertation shows an alternative approach that exploits in a smart and efficient way the hardware image processing unit almost integrated in every current multimedia application processors to implement a hardware assisted image compensation that allows dynamic scaling of the backlight with a negligible impact on QoS. The proposed approach overcomes CPU-intensive techniques by saving system power without requiring either a dedicated display technology or hardware modification. Thesis Overview The remainder of the thesis is organized as follows. The first part is focused on enhancing energy efficiency and programmability of modern Multi-Processor System-on-Chips (MPSoCs). Chapter 2 gives an overview about architectural trends in embedded systems, illustrating the principal features of new technologies and the key challenges still open. Chapter 3 presents a QoS-driven methodology for optimal allocation and frequency selection for MPSoCs. The methodology is based on functional simulation and full system power estimation. Chapter 4 targets allocation and scheduling of pipelined stream-oriented applications on top of distributed memory architectures with messaging support. We tackled the complexity of the problem by means of decomposition and no-good generation, and prove the increased computational efficiency of this approach with respect to traditional ones. Chapter 5 presents a cooperative framework to solve the allocation, scheduling and voltage/frequency selection problem to optimality for energyefficient MPSoCs, while in Chapter 6 applications with conditional task graph are taken into account. Finally Chapter 7 proposes a complete framework, called Cellflow, to help programmers in efficient software implementation on a real architecture, the Cell Broadband Engine processor. The second part is focused on energy efficient software techniques for LCD displays. Chapter 8 gives an overview about portable device display technologies, illustrating the principal features of LCD video systems and the key challenges still open. Chapter 9 shows several energy efficient software techniques present in literature, while Chapter 10 illustrates in details our method for saving significant power in an LCD panel. Finally, conclusions are drawn, reporting the main research contributions that have been discussed throughout this dissertation.

Max Bill in Italia . Lo spazio logico dell'architettura

I Max Bill is an intense giornata of a big fresco. An analysis of the main social, artistic and cultural events throughout the twentieth century is needed in order to trace his career through his masterpieces and architectures. Some of the faces of this hypothetical mural painting are, among others, Le Corbusier, Walter Gropius, Ernesto Nathan Rogers, Kandinskij, Klee, Mondrian, Vatongerloo, Ignazio Silone, while the backcloth is given by artistic avant-gardes, Bauhaus, International Exhibitions, CIAM, war events, reconstruction, Milan Triennali, Venice Biennali, the School of Ulm. Architect, even though more known as painter, sculptor, designer and graphic artist, Max Bill attends the Bauhaus as a student in the years 1927-1929, and from this experience derives the main features of a rational, objective, constructive and non figurative art. His research is devoted to give his art a scientific methodology: each work proceeds from the analysis of a problem to the logical and always verifiable solution of the same problem. By means of composition elements (such as rhythm, seriality, theme and its variation, harmony and dissonance), he faces, with consistent results, themes apparently very distant from each other as the project for the H.f.G. or the design for a font. Mathematics are a constant reference frame as field of certainties, order, objectivity: ‘for Bill mathematics are never confined to a simple function: they represent a climate of spiritual certainties, and also the theme of non attempted in its purest state, objectivity of the sign and of the geometrical place, and at the same time restlessness of the infinity: Limited and Unlimited ’. In almost sixty years of activity, experiencing all artistic fields, Max Bill works, projects, designs, holds conferences and exhibitions in Europe, Asia and Americas, confronting himself with the most influencing personalities of the twentieth century. In such a vast scenery, the need to limit the investigation field combined with the necessity to address and analyse the unpublished and original aspect of Bill’s relations with Italy. The original contribution of the present research regards this particular ‘geographic delimitation’; in particular, beyond the deep cultural exchanges between Bill and a series of Milanese architects, most of all with Rogers, two main projects have been addressed: the realtà nuova at Milan Triennale in 1947, and the Contemporary Art Museum in Florence in 1980. It is important to note that these projects have not been previously investigated, and the former never appears in the sources either. These works, together with the most well-known ones, such as the projects for the VI and IX Triennale, and the Swiss pavilion for the Biennale, add important details to the reference frame of the relations which took place between Zurich and Milan. Most of the occasions for exchanges took part in between the Thirties and the Fifties, years during which Bill underwent a significant period of artistic growth. He meets the Swiss progressive architects and the Paris artists from the Abstraction-Création movement, enters the CIAM, collaborates with Le Corbusier to the third volume of his Complete Works, and in Milan he works and gets confronted with the events related to post-war reconstruction. In these years Bill defines his own working methodology, attaining an artistic maturity in his work. The present research investigates the mentioned time period, despite some necessary exceptions. II The official Max Bill bibliography is naturally wide, including spreading works along with ones more devoted to analytical investigation, mainly written in German and often translated into French and English (Max Bill himself published his works in three languages). Few works have been published in Italian and, excluding the catalogue of the Parma exhibition from 1977, they cannot be considered comprehensive. Many publications are exhibition catalogues, some of which include essays written by Max Bill himself, some others bring Bill’s comments in a educational-pedagogical approach, to accompany the observer towards a full understanding of the composition processes of his art works. Bill also left a great amount of theoretical speculations to encourage a critical reading of his works in the form of books edited or written by him, and essays published in ‘Werk’, magazine of the Swiss Werkbund, and other international reviews, among which Domus and Casabella. These three reviews have been important tools of analysis, since they include tracks of some of Max Bill’s architectural works. The architectural aspect is less investigated than the plastic and pictorial ones in all the main reference manuals on the subject: Benevolo, Tafuri and Dal Co, Frampton, Allenspach consider Max Bill as an artist proceeding in his work from Bauhaus in the Ulm experience . A first filing of his works was published in 2004 in the monographic issue of the Spanish magazine 2G, together with critical essays by Karin Gimmi, Stanislaus von Moos, Arthur Rüegg and Hans Frei, and in ‘Konkrete Architektur?’, again by Hans Frei. Moreover, the monographic essay on the Atelier Haus building by Arthur Rüegg from 1997, and the DPA 17 issue of the Catalonia Polytechnic with contributions of Carlos Martì, Bruno Reichlin and Ton Salvadò, the latter publication concentrating on a few Bill’s themes and architectures. An urge to studying and going in depth in Max Bill’s works was marked in 2008 by the centenary of his birth and by a recent rediscovery of Bill as initiator of the ‘minimalist’ tradition in Swiss architecture. Bill’s heirs are both very active in promoting exhibitions, researching and publishing. Jakob Bill, Max Bill’s son and painter himself, recently published a work on Bill’s experience in Bauhaus, and earlier on he had published an in-depth study on ‘Endless Ribbons’ sculptures. Angela Thomas Schmid, Bill’s wife and art historian, published in end 2008 the first volume of a biography on Max Bill and, together with the film maker Eric Schmid, produced a documentary film which was also presented at the last Locarno Film Festival. Both biography and documentary concentrate on Max Bill’s political involvement, from antifascism and 1968 protest movements to Bill experiences as Zurich Municipality councilman and member of the Swiss Confederation Parliament. In the present research, the bibliography includes also direct sources, such as interviews and original materials in the form of letters correspondence and graphic works together with related essays, kept in the max+binia+jakob bill stiftung archive in Zurich. III The results of the present research are organized into four main chapters, each of them subdivided into four parts. The first chapter concentrates on the research field, reasons, tools and methodologies employed, whereas the second one consists of a short biographical note organized by topics, introducing the subject of the research. The third chapter, which includes unpublished events, traces the historical and cultural frame with particular reference to the relations between Max Bill and the Italian scene, especially Milan and the architects Rogers and Baldessari around the Fifties, searching the themes and the keys for interpretation of Bill’s architectures and investigating the critical debate on the reviews and the plastic survey through sculpture. The fourth and last chapter examines four main architectures chosen on a geographical basis, all devoted to exhibition spaces, investigating Max Bill’s composition process related to the pictorial field. Paintings has surely been easier and faster to investigate and verify than the building field. A doctoral thesis discussed in Lausanne in 1977 investigating Max Bill’s plastic and pictorial works, provided a series of devices which were corrected and adapted for the definition of the interpretation grid for the composition structures of Bill’s main architectures. Four different tools are employed in the investigation of each work: a context analysis related to chapter three results; a specific theoretical essay by Max Bill briefly explaining his main theses, even though not directly linked to the very same work of art considered; the interpretation grid for the composition themes derived from a related pictorial work; the architecture drawing and digital three-dimensional model. The double analysis of the architectural and pictorial fields is functional to underlining the relation among the different elements of the composition process; the two fields, however, cannot be compared and they stay, in Max Bill’s works as in the present research, interdependent though self-sufficient. IV An important aspect of Max Bill production is self-referentiality: talking of Max Bill, also through Max Bill, as a need for coherence instead of a method limitation. Ernesto Nathan Rogers describes Bill as the last humanist, and his horizon is the known world but, as the ‘Concrete Art’ of which he is one of the main representatives, his production justifies itself: Max Bill not only found a method, but he autonomously re-wrote the ‘rules of the game’, derived timeless theoretical principles and verified them through a rich and interdisciplinary artistic production. The most recurrent words in the present research work are synthesis, unity, space and logic. These terms are part of Max Bill’s vocabulary and can be referred to his works. Similarly, graphic settings or analytical schemes in this research text referring to or commenting Bill’s architectural projects were drawn up keeping in mind the concise precision of his architectural design. As for Mies van der Rohe, it has been written that Max Bill took art to ‘zero degree’ reaching in this way a high complexity. His works are a synthesis of art: they conceptually encompass all previous and –considered their developments- most of contemporary pictures. Contents and message are generally explicitly declared in the title or in Bill’s essays on his artistic works and architectural projects: the beneficiary is invited to go through and re-build the process of synthesis generating the shape. In the course of the interview with the Milan artist Getulio Alviani, he tells how he would not write more than a page for an essay on Josef Albers: everything was already evident ‘on the surface’ and any additional sentence would be redundant. Two years after that interview, these pages attempt to decompose and single out the elements and processes connected with some of Max Bill’s works which, for their own origin, already contain all possible explanations and interpretations. The formal reduction in favour of contents maximization is, perhaps, Max Bill’s main lesson.

Uniquitous internet middleware: architecture design and prototype evaluation

Technology advances in recent years have dramatically changed the way users exploit contents and services available on the Internet, by enforcing pervasive and mobile computing scenarios and enabling access to networked resources almost from everywhere, at anytime, and independently of the device in use. In addition, people increasingly require to customize their experience, by exploiting specific device capabilities and limitations, inherent features of the communication channel in use, and interaction paradigms that significantly differ from the traditional request/response one. So-called Ubiquitous Internet scenario calls for solutions that address many different challenges, such as device mobility, session management, content adaptation, context-awareness and the provisioning of multimodal interfaces. Moreover, new service opportunities demand simple and effective ways to integrate existing resources into new and value added applications, that can also undergo run-time modifications, according to ever-changing execution conditions. Despite service-oriented architectural models are gaining momentum to tame the increasing complexity of composing and orchestrating distributed and heterogeneous functionalities, existing solutions generally lack a unified approach and only provide support for specific Ubiquitous Internet aspects. Moreover, they usually target rather static scenarios and scarcely support the dynamic nature of pervasive access to Internet resources, that can make existing compositions soon become obsolete or inadequate, hence in need of reconfiguration. This thesis proposes a novel middleware approach to comprehensively deal with Ubiquitous Internet facets and assist in establishing innovative application scenarios. We claim that a truly viable ubiquity support infrastructure must neatly decouple distributed resources to integrate and push any kind of content-related logic outside its core layers, by keeping only management and coordination responsibilities. Furthermore, we promote an innovative, open, and dynamic resource composition model that allows to easily describe and enforce complex scenario requirements, and to suitably react to changes in the execution conditions.