Mechanical behavior of flat and curved laminates interleaved by electrospun nanofibers

A major weakness of composite materials is that low-velocity impact, introduced accidentally during manufacture, operation or maintenance of the aircraft, may result in delaminations between the plies. Therefore, the first part of this study is focused on mechanics of curved laminates under impact. For this aim, the effect of preloading on impact response of curved composite laminates is considered. By applying the preload, the stress through the thickness and curvature of the laminates increased. The results showed that all impact parameters are varied significantly. For understanding the contribution rate of preloading and pre-stress on the obtained results another test is designed. The interesting phenomenon is that the preloading can decrease the damaged area when the curvature of the both specimens is the same. Finally the effect of curvature type, concave and convex, is investigated under impact loading. In the second part, a new composition of nanofibrous mats are developed to improve the efficiency of curved laminates under impact loading. Therefore, at first some fracture tests are conducted to consider the effect of Nylon 6,6, PCL, and their mixture on mode I and mode II fracture toughness. For this goal, nanofibers are electrospun and interleaved between mid-plane of laminate composite to conduct mode I and mode II tests. The results shows that efficiency of Nylon 6,6 is better than PCL in mode II, while the effect of PCL on fracture toughness of mode I is more. By mixing these nanofibers the shortage of the individual nanofibers is compensated and so the Nylon 6,6/PCL nanofibers could increased mode I and II fracture toughness. Then all these nanofibers are used between all layers of composite layers to investigate their effect on damaged area. The results showed that PCL could decrease the damaged area about 25% and Nylon 6,6 and mixed nanofibers about 50%.

Displacement Analysis of Under-Constrained Cable-Driven Parallel Robots

This dissertation studies the geometric static problem of under-constrained cable-driven parallel robots (CDPRs) supported by n cables, with n ≤ 6. The task consists of determining the overall robot configuration when a set of n variables is assigned. When variables relating to the platform posture are assigned, an inverse geometric static problem (IGP) must be solved; whereas, when cable lengths are given, a direct geometric static problem (DGP) must be considered. Both problems are challenging, as the robot continues to preserve some degrees of freedom even after n variables are assigned, with the final configuration determined by the applied forces. Hence, kinematics and statics are coupled and must be resolved simultaneously. In this dissertation, a general methodology is presented for modelling the aforementioned scenario with a set of algebraic equations. An elimination procedure is provided, aimed at solving the governing equations analytically and obtaining a least-degree univariate polynomial in the corresponding ideal for any value of n. Although an analytical procedure based on elimination is important from a mathematical point of view, providing an upper bound on the number of solutions in the complex field, it is not practical to compute these solutions as it would be very time-consuming. Thus, for the efficient computation of the solution set, a numerical procedure based on homotopy continuation is implemented. A continuation algorithm is also applied to find a set of robot parameters with the maximum number of real assembly modes for a given DGP. Finally, the end-effector pose depends on the applied load and may change due to external disturbances. An investigation into equilibrium stability is therefore performed.

Power Converters and Electric Drives for Smart Grid Applications

The present dissertation aims to explore, theoretically and experimentally, the problems and the potential advantages of different types of power converters for “Smart Grid” applications, with particular emphasis on multi-level architectures, which are attracting a rising interest even for industrial requests. The models of the main multilevel architectures (Diode-Clamped and Cascaded) are shown. The best suited modulation strategies to function as a network interface are identified. In particular, the close correlation between PWM (Pulse Width Modulation) approach and SVM (Space Vector Modulation) approach is highlighted. An innovative multilevel topology called MMC (Modular Multilevel Converter) is investigated, and the single-phase, three-phase and "back to back" configurations are analyzed. Specific control techniques that can manage, in an appropriate way, the charge level of the numerous capacitors and handle the power flow in a flexible way are defined and experimentally validated. Another converter that is attracting interest in “Power Conditioning Systems” field is the “Matrix Converter”. Even in this architecture, the output voltage is multilevel. It offers an high quality input current, a bidirectional power flow and has the possibility to control the input power factor (i.e. possibility to participate to active and reactive power regulations). The implemented control system, that allows fast data acquisition for diagnostic purposes, is described and experimentally verified.

Sistemi tecnologici innovativi di involucro per il recupero del patrimonio edilizio recente. L'edilizia scolastica nel Comune di Bologna

La ricerca è volta a presentare un nuovo approccio integrato, a supporto di operatori e progettisti, per la gestione dell’intero processo progettuale di interventi di riqualificazione energetica e architettonica del patrimonio edilizio recente, mediante l’impiego di soluzioni tecnologiche innovative di involucro edilizio. Lo studio richiede necessariamente l’acquisizione di un repertorio selezionato di sistemi costruttivi di involucro, come base di partenza per l’elaborazione di soluzioni progettuali di recupero delle scuole appartenenti al secondo dopoguerra, in conglomerato cementizio armato, prevalentemente prefabbricate. Il progetto individua procedimenti costruttivi ecocompatibili per la progettazione di componenti prefabbricati di involucro “attivo”, adattabile ed efficiente, da assemblare a secco, nel rispetto dei requisiti prestazionali richiesti dalle attuali normative. La ricerca è finalizzata alla gestione dell’intero processo, supportato da sistemi di rilevazione geometrica, collegati a software di programmazione parametrica per la modellazione di superfici adattabili alla morfologia dei fabbricati oggetto di intervento. Tali strumenti informatizzati CAD-CAM sono connessi a macchine a controllo numerico CNC per la produzione industrializzata degli elementi costruttivi “su misura”. A titolo esemplificativo dell’approccio innovativo proposto, si formulano due possibili soluzioni di involucro in linea con i paradigmi della ricerca, nel rispetto dei principi di sostenibilità, intesa come modularità, rapidità di posa, reversibilità, recupero e riciclo di materiali. In particolare, le soluzioni innovative sono accomunate dall’applicazione di una tecnica basata sull’assemblaggio di elementi prefabbricati, dall’adozione di una trama esagonale per la tassellazione della nuova superficie di facciata, e dall’utilizzo del medesimo materiale termico isolante, plastico e inorganico, riciclato ed ecosostenibile, a basso impatto ambientale (AAM - Alkali Activated Materials). Le soluzioni progettuali proposte, sviluppate presso le due sedi coinvolte nella cotutela (Università di Bologna, Université Paris-Est) sono affrontate secondo un protocollo scientifico che prevede: progettazione del sistema costruttivo, analisi meccanica e termica, sperimentazione costruttiva, verifica delle tecniche di messa in opera e dei requisiti prestazionali.

Simulazione dinamica di un veicolo dotato di powertrain ibrido endotermico-elettrico

Nel panorama motoristico ed automobilistico moderno lo sviluppo di motori a combustione interna e veicoli è fortemente influenzato da diverse esigenze che spesso sono in contrasto le une con le altre. Infatti gli obiettivi di economicità e riduzione dei costi riguardanti la produzione e la commercializzazione dei prodotti sono in contrasto con gli sforzi che devono essere operati dalle case produttrici per soddisfare le sempre più stringenti normative riguardanti le emissioni inquinanti ed i consumi di carburante dei veicoli. Fra le numerose soluzioni presenti i veicoli ibridi rappresentano una alternativa che allo stato attuale è già presente sul mercato in varie forme, a seconda della tipologie di energie accoppiate. In letteratura è possibile trovare numerosi studi che trattano l’ottimizzazione dei componenti o delle strategie di controllo di queste tipologie di veicoli: in moltissimi casi l’obiettivo è quello di minimizzare consumi ed emissioni inquinanti. Normalmente non viene posta particolare attenzione agli effetti che l’aggiunta delle macchine elettriche e dei componenti necessari per il funzionamento delle stesse hanno sulla dinamica del veicolo. Il presente lavoro di tesi è incentrato su questi aspetti: si è considerata la tipologia di veicoli ibridi termici-elettrici di tipo parallelo andando ad analizzare come cambiasse il comportamento dinamico del veicolo in funzione del tipo di installazione considerato per la parte elettrica del powertrain. In primo luogo è stato quindi necessario costruire ed implementare un modello dinamico di veicolo che permettesse di applicare coppie alle quattro ruote in maniera indipendente per considerare diverse tipologie di powertrain. In seguito si sono analizzate le differenze di comportamento dinamico fra il veicolo considerato e l’equivalente versione ibrida e i possibili utilizzi delle macchine elettriche per correggere eventuali deterioramenti o cambiamenti indesiderati nelle prestazioni del veicolo.

Development of a microgrid with renewable energy sources and electrochemical storage system integration

Beside the traditional paradigm of "centralized" power generation, a new concept of "distributed" generation is emerging, in which the same user becomes pro-sumer. During this transition, the Energy Storage Systems (ESS) can provide multiple services and features, which are necessary for a higher quality of the electrical system and for the optimization of non-programmable Renewable Energy Source (RES) power plants. A ESS prototype was designed, developed and integrated into a renewable energy production system in order to create a smart microgrid and consequently manage in an efficient and intelligent way the energy flow as a function of the power demand. The produced energy can be introduced into the grid, supplied to the load directly or stored in batteries. The microgrid is composed by a 7 kW wind turbine (WT) and a 17 kW photovoltaic (PV) plant are part of. The load is given by electrical utilities of a cheese factory. The ESS is composed by the following two subsystems, a Battery Energy Storage System (BESS) and a Power Control System (PCS). With the aim of sizing the ESS, a Remote Grid Analyzer (RGA) was designed, realized and connected to the wind turbine, photovoltaic plant and the switchboard. Afterwards, different electrochemical storage technologies were studied, and taking into account the load requirements present in the cheese factory, the most suitable solution was identified in the high temperatures salt Na-NiCl2 battery technology. The data acquisition from all electrical utilities provided a detailed load analysis, indicating the optimal storage size equal to a 30 kW battery system. Moreover a container was designed and realized to locate the BESS and PCS, meeting all the requirements and safety conditions. Furthermore, a smart control system was implemented in order to handle the different applications of the ESS, such as peak shaving or load levelling.

A New Test Rig for In-Vitro Evaluation of the Knee Joint Behaviour

The evaluation of the knee joint behavior is fundamental in many applications, such as joint modeling, prosthesis and orthosis design. In-vitro tests are important in order to analyse knee behavior when simulating various loading conditions and studying physiology of the joint. A new test rig for in-vitro evaluation of the knee joint behavior is presented in this paper. It represents the evolution of a previously proposed rig, designed to overcome its principal limitations and to improve its performances. The design procedure and the adopted solution in order to satisfy the specifications are presented here. Thanks to its 6-6 Gough-Stewart parallel manipulator loading system, the rig replicates general loading conditions, like daily actions or clinical tests, on the specimen in a wide range of flexion angles. The restraining actions of knee muscles can be simulated when active actions are simulated. The joint motion in response to the applied loads, guided by passive articular structures and muscles, is permitted by the characteristics of the loading system which is force controlled. The new test rig guarantees visibility so that motion can be measured by an optoelectronic system. Furthermore, the control system of the new test rig allows the estimation of the contribution of the principal leg muscles in guaranteeing the equilibrium of the joint by the system for muscle simulation. Accuracy in positioning is guaranteed by the designed tibia and femur fixation systems,which allow unmounting and remounting the specimen in the same pose. The test rig presented in this paper permits the analysis of the behavior of the knee joint and comparative analysis on the same specimen before and after surgery, in a way to assess the goodness of prostheses or surgical treatments.

Analysis and design of high performance multiphase electric drives for vehicle and aircraft applications

The first part of this thesis has focused on the construction of a twelve-phase asynchronous machine for More Electric Aircraft (MEA) applications. In fact, the aerospace world has found in electrification the way to improve the efficiency, reliability and maintainability of an aircraft. This idea leads to the aircraft a new management and distribution of electrical services. In this way is possible to remove or to reduce the hydraulic, mechanical and pneumatic systems inside the aircraft. The second part of this dissertation is dedicated on the enhancement of the control range of matrix converters (MCs) operating with non-unity input power factor and, at the same time, on the reduction of the switching power losses. The analysis leads to the determination in closed form of a modulation strategy that features a control range, in terms of output voltage and input power factor, that is greater than that of the traditional strategies under the same operating conditions, and a reduction in the switching power losses.

Kinematics and statics of cable-driven parallel robots by interval-analysis-based methods

In the past two decades the work of a growing portion of researchers in robotics focused on a particular group of machines, belonging to the family of parallel manipulators: the cable robots. Although these robots share several theoretical elements with the better known parallel robots, they still present completely (or partly) unsolved issues. In particular, the study of their kinematic, already a difficult subject for conventional parallel manipulators, is further complicated by the non-linear nature of cables, which can exert only efforts of pure traction. The work presented in this thesis therefore focuses on the study of the kinematics of these robots and on the development of numerical techniques able to address some of the problems related to it. Most of the work is focused on the development of an interval-analysis based procedure for the solution of the direct geometric problem of a generic cable manipulator. This technique, as well as allowing for a rapid solution of the problem, also guarantees the results obtained against rounding and elimination errors and can take into account any uncertainties in the model of the problem. The developed code has been tested with the help of a small manipulator whose realization is described in this dissertation together with the auxiliary work done during its design and simulation phases.

Meccanizzazione dei vigneti allevati a doppia cortina e a cordone libero

La ricerca svolta ha voluto approfondire le possibilità offerte dai sistemi di allevamento dei vigneti a Doppia Cortina (GDC) e a Cordone Libero nei riguardi della meccanizzazione. La ricerca ha considerato gli interventi di potatura invernale, di gestione della chioma (spollonatura, cimatura, defogliazione e pettinatura della doppia cortina) e di vendemmia. Un’operazione particolarmente seguita è stata la potatura invernale realizzando differenti livelli di meccanizzazione. Tutti gli interventi sono stati eseguiti sia manualmente che meccanicamente, confrontando i tempi d’impiego, la qualità del lavoro svolto e gli impegni di manodopera. I risultati sono stati sintetizzati in una valutazione economica, ipotizzando differenti livelli di costo della manodopera impiegata, per ottenere giudizi di convenienza per i singoli interventi e per costruire una valutazione completa e più organica della linea di lavoro proposta. Nelle due forme d’allevamento la meccanizzazione della potatura invernale e della gestione della chioma hanno rispettato pienamente gli obbiettivi tecnici prefissati, dimostrando di essere un valido mezzo per ridurre tempi e costi di gestione. Per questi interventi l’acquisto delle macchine risulta conveniente anche per vigneti di piccola dimensione. Ancor più evidenti in queste due forme d’allevamento sono i vantaggi economici offerti dalla vendemmia meccanica, realizzata con pochi maltrattamenti e perdite di prodotto. La tendenza a meccanizzare integralmente gli interventi di gestione del ciclo colturale della vite, può essere nei prossimi anni un motivo di interesse e di scelta nella realizzazione di nuovi impianti con queste due forme di allevamento, che hanno dimostrato di essere un’espressione completa di sinergia tra macchina e pianta.

Design of a new harrow type wool transport mechanism to reduce fibre entanglement

The wool is entangled at several stages of its processing. In the conventional scouring machines, the prongs or the rakes agitate the wool and lead the fiber entanglement. Several scouring systems have been commercialized in order to reduce the fiber entanglement. In spite of the existing technologies, the conventional scouring machines are widely used in wool processing. In this thesis, a new approach for the harrow type wool transport mechanism has been introduced. The proposed mechanism has been designed based on the motion of the conventional harrow type wool transport mechanism by exploiting new synthesis concepts. The developed structure has been synthesized based on the Hrones and Nelson's "Atlas of four bar linkages". The four bar linkage has been applied for the desired trajectory of the developed wool transport mechanism. The prongs of the developed mechanism immerse the wool into the scouring liquor and gently propel forward toward the end of the machine with approximately straight line motion in a certain length instead of circular or elliptical motion typical of the conventional machines.