Creazione e sviluppo di un sistema di controllo in tempo reale per un sistema fuel cell

The control of a proton exchange membrane fuel cell system (PEM FC) for domestic heat and power supply requires extensive control measures to handle the complicated process. Highly dynamic and non linear behavior, increase drastically the difficulties to find the optimal design and control strategies. The objective is to design, implement and commission a controller for the entire fuel cell system. The fuel cell process and the control system are engineered simultaneously; therefore there is no access to the process hardware during the control system development. Therefore the method of choice was a model based design approach, following the rapid control prototyping (RCP) methodology. The fuel cell system is simulated using a fuel cell library which allowed thermodynamic calculations. In the course of the development the process model is continuously adapted to the real system. The controller application is designed and developed in parallel and thereby tested and verified against the process model. Furthermore, after the commissioning of the real system, the process model can be also better identified and parameterized utilizing measurement data to perform optimization procedures. The process model and the controller application are implemented in Simulink using Mathworks` Real Time Workshop (RTW) and the xPC development suite for MiL (model-in-theloop) and HiL (hardware-in-the-loop) testing. It is possible to completely develop, verify and validate the controller application without depending on the real fuel cell system, which is not available for testing during the development process. The fuel cell system can be immediately taken into operation after connecting the controller to the process.

Tecniche per il controllo dinamico del consumo di potenza per piattaforme system-on-chip

Providing support for multimedia applications on low-power mobile devices remains a significant research challenge. This is primarily due to two reasons: • Portable mobile devices have modest sizes and weights, and therefore inadequate resources, low CPU processing power, reduced display capabilities, limited memory and battery lifetimes as compared to desktop and laptop systems. • On the other hand, multimedia applications tend to have distinctive QoS and processing requirementswhichmake themextremely resource-demanding. This innate conflict introduces key research challenges in the design of multimedia applications and device-level power optimization. Energy efficiency in this kind of platforms can be achieved only via a synergistic hardware and software approach. In fact, while System-on-Chips are more and more programmable thus providing functional flexibility, hardwareonly power reduction techniques cannot maintain consumption under acceptable bounds. It is well understood both in research and industry that system configuration andmanagement cannot be controlled efficiently only relying on low-level firmware and hardware drivers. In fact, at this level there is lack of information about user application activity and consequently about the impact of power management decision on QoS. Even though operating system support and integration is a requirement for effective performance and energy management, more effective and QoSsensitive power management is possible if power awareness and hardware configuration control strategies are tightly integratedwith domain-specificmiddleware services. The main objective of this PhD research has been the exploration and the integration of amiddleware-centric energymanagement with applications and operating-system. We choose to focus on the CPU-memory and the video subsystems, since they are the most power-hungry components of an embedded system. A second main objective has been the definition and implementation of software facilities (like toolkits, API, and run-time engines) in order to improve programmability and performance efficiency of such platforms. Enhancing energy efficiency and programmability ofmodernMulti-Processor System-on-Chips (MPSoCs) Consumer applications are characterized by tight time-to-market constraints and extreme cost sensitivity. The software that runs on modern embedded systems must be high performance, real time, and even more important low power. Although much progress has been made on these problems, much remains to be done. Multi-processor System-on-Chip (MPSoC) are increasingly popular platforms for high performance embedded applications. This leads to interesting challenges in software development since efficient software development is a major issue for MPSoc designers. An important step in deploying applications on multiprocessors is to allocate and schedule concurrent tasks to the processing and communication resources of the platform. The problem of allocating and scheduling precedenceconstrained tasks on processors in a distributed real-time system is NP-hard. There is a clear need for deployment technology that addresses thesemulti processing issues. This problem can be tackled by means of specific middleware which takes care of allocating and scheduling tasks on the different processing elements and which tries also to optimize the power consumption of the entire multiprocessor platform. This dissertation is an attempt to develop insight into efficient, flexible and optimalmethods for allocating and scheduling concurrent applications tomultiprocessor architectures. It is a well-known problem in literature: this kind of optimization problems are very complex even in much simplified variants, therefore most authors propose simplified models and heuristic approaches to solve it in reasonable time. Model simplification is often achieved by abstracting away platform implementation ”details”. As a result, optimization problems become more tractable, even reaching polynomial time complexity. Unfortunately, this approach creates an abstraction gap between the optimization model and the real HW-SW platform. The main issue with heuristic or, more in general, with incomplete search is that they introduce an optimality gap of unknown size. They provide very limited or no information on the distance between the best computed solution and the optimal one. The goal of this work is to address both abstraction and optimality gaps, formulating accurate models which accounts for a number of ”non-idealities” in real-life hardware platforms, developing novel mapping algorithms that deterministically find optimal solutions, and implementing software infrastructures required by developers to deploy applications for the targetMPSoC platforms. Energy Efficient LCDBacklightAutoregulation on Real-LifeMultimediaAp- plication Processor Despite the ever increasing advances in Liquid Crystal Display’s (LCD) technology, their power consumption is still one of the major limitations to the battery life of mobile appliances such as smart phones, portable media players, gaming and navigation devices. There is a clear trend towards the increase of LCD size to exploit the multimedia capabilities of portable devices that can receive and render high definition video and pictures. Multimedia applications running on these devices require LCD screen sizes of 2.2 to 3.5 inches andmore to display video sequences and pictures with the required quality. LCD power consumption is dependent on the backlight and pixel matrix driving circuits and is typically proportional to the panel area. As a result, the contribution is also likely to be considerable in future mobile appliances. To address this issue, companies are proposing low power technologies suitable for mobile applications supporting low power states and image control techniques. On the research side, several power saving schemes and algorithms can be found in literature. Some of them exploit software-only techniques to change the image content to reduce the power associated with the crystal polarization, some others are aimed at decreasing the backlight level while compensating the luminance reduction by compensating the user perceived quality degradation using pixel-by-pixel image processing algorithms. The major limitation of these techniques is that they rely on the CPU to perform pixel-based manipulations and their impact on CPU utilization and power consumption has not been assessed. This PhDdissertation shows an alternative approach that exploits in a smart and efficient way the hardware image processing unit almost integrated in every current multimedia application processors to implement a hardware assisted image compensation that allows dynamic scaling of the backlight with a negligible impact on QoS. The proposed approach overcomes CPU-intensive techniques by saving system power without requiring either a dedicated display technology or hardware modification. Thesis Overview The remainder of the thesis is organized as follows. The first part is focused on enhancing energy efficiency and programmability of modern Multi-Processor System-on-Chips (MPSoCs). Chapter 2 gives an overview about architectural trends in embedded systems, illustrating the principal features of new technologies and the key challenges still open. Chapter 3 presents a QoS-driven methodology for optimal allocation and frequency selection for MPSoCs. The methodology is based on functional simulation and full system power estimation. Chapter 4 targets allocation and scheduling of pipelined stream-oriented applications on top of distributed memory architectures with messaging support. We tackled the complexity of the problem by means of decomposition and no-good generation, and prove the increased computational efficiency of this approach with respect to traditional ones. Chapter 5 presents a cooperative framework to solve the allocation, scheduling and voltage/frequency selection problem to optimality for energyefficient MPSoCs, while in Chapter 6 applications with conditional task graph are taken into account. Finally Chapter 7 proposes a complete framework, called Cellflow, to help programmers in efficient software implementation on a real architecture, the Cell Broadband Engine processor. The second part is focused on energy efficient software techniques for LCD displays. Chapter 8 gives an overview about portable device display technologies, illustrating the principal features of LCD video systems and the key challenges still open. Chapter 9 shows several energy efficient software techniques present in literature, while Chapter 10 illustrates in details our method for saving significant power in an LCD panel. Finally, conclusions are drawn, reporting the main research contributions that have been discussed throughout this dissertation.

Controllo dell'atto di prensione: coinvolgimento dell'area V6A nell'orientamento del polso

Prehension in an act of coordinated reaching and grasping. The reaching component is concerned with bringing the hand to object to be grasped (transport phase); the grasping component refers to the shaping of the hand according to the object features (grasping phase) (Jeannerod, 1981). Reaching and grasping involve different muscles, proximal and distal muscles respectively, and are controlled by different parietofrontal circuit (Jeannerod et al., 1995): a medial circuit, involving area of superior parietal lobule and dorsal premotor area 6 (PMd) (dorsomedial visual stream), is mainly concerned with reaching; a lateral circuit, involving the inferior parietal lobule and ventral premotor area 6 (PMv) (dorsolateral visual stream), with grasping. Area V6A is located in the caudalmost part of the superior parietal lobule, so it belongs to the dorsomedial visual stream; it contains neurons sensitive to visual stimuli (Galletti et al. 1993, 1996, 1999) as well as cells sensitive to the direction of gaze (Galletti et al. 1995) and cells showing saccade-related activity (Nakamura et al. 1999; Kutz et al. 2003). Area V6A contains also arm-reaching neurons likely involved in the control of the direction of the arm during movements towards objects in the peripersonal space (Galletti et al. 1997; Fattori et al. 2001). The present results confirm this finding and demonstrate that during the reach-to-grasp the V6A neurons are also modulated by the orientation of the wrist. Experiments were approved by the Bioethical Committee of the University of Bologna and were performed in accordance with National laws on care and use of laboratory animals and with the European Communities Council Directive of 24th November 1986 (86/609/EEC), recently revised by the Council of Europe guidelines (Appendix A of Convention ETS 123). Experiments were performed in two awake Macaca fascicularis. Each monkey was trained to sit in a primate chair with the head restrained to perform reaching and grasping arm movements in complete darkness while gazing a small fixation point. The object to be grasped was a handle that could have different orientation. We recorded neural activity from 163 neurons of the anterior parietal sulcus; 116/163 (71%) neurons were modulated by the reach-to-grasp task during the execution of the forward movements toward the target (epoch MOV), 111/163 (68%) during the pulling of the handle (epoch HOLD) and 102/163 during the execution of backward movements (epoch M2) (t_test, p ≤ 0.05). About the 45% of the tested cells turned out to be sensitive to the orientation of the handle (one way ANOVA, p ≤ 0.05). To study how the distal components of the movement, such as the hand preshaping during the reaching of the handle, could influence the neuronal discharge, we compared the neuronal activity during the reaching movements towards the same spatial location in reach-to-point and reach-to-grasp tasks. Both tasks required proximal arm movements; only the reach-to-grasp task required distal movements to orient the wrist and to shape the hand to grasp the handle. The 56% of V6A cells showed significant differences in the neural discharge (one way ANOVA, p ≤ 0.05) between the reach-to-point and the reach-to-grasp tasks during MOV, 54% during HOLD and 52% during M2. These data show that reaching and grasping are processed by the same population of neurons, providing evidence that the coordination of reaching and grasping takes place much earlier than previously thought, i.e., in the parieto-occipital cortex. The data here reported are in agreement with results of lesions to the medial posterior parietal cortex in both monkeys and humans, and with recent imaging data in humans, all of them indicating a functional coupling in the control of reaching and grasping by the medial parietofrontal circuit.

Dimensionamento di invasi per il controllo dei deflussi nei bacini urbanizzati

Urbanization is a continuing phenomenon in all the world. Grasslands, forests, etc. are being continually changed to residential, commercial and industrial complexes, roads and streets, and so on. One of the side effects of urbanization with which engineers and planners must deal with, is the increase of peak flows and volumes of runoff from rainfall events. As a result, the urban drainage and flood control systems must be designed to accommodate the peak flows from a variety of storms that may occur. Usually the peak flow, after development, is required not to exceed what would have occurred from the same storm under conditions existing prior to development. In order to do this it is necessary to design detention storage to hold back runoff and to release it downstream at controlled rates. In the first part of the work have been developed various simplified formulations that can be adopted for the design of stormwater detention facilities. In order to obtain a simplified hydrograph were adopted two approaches: the kinematic routing technique and the linear reservoir schematization. For the two approaches have been also obtained other two formulations depending if the IDF (intensity-duration-frequency) curve is described with two or three parameters. Other formulations have been developed taking into account if the outlet have a constant discharge or it depends on the water level in the pond. All these formulations can be easily applied when are known the characteristics of the drainage system and maximum discharge that these is in the outlet and has been defined a Return Period which characterize the IDF curve. In this way the volume of the detention pond can be calculated. In the second part of the work have been analyzed the design of detention ponds adopting continuous simulation models. The drainage systems adopted for the simulations, performed with SWMM5, are fictitious systems characterized by different sizes, and different shapes of the catchments and with a rainfall historical time series of 16 years recorded in Bologna. This approach suffers from the fact that continuous record of rainfall is often not available and when it is, the cost of such modelling can be very expensive, and that the majority of design practitioners are not prepared to use continuous long term modelling in the design of stormwater detention facilities. In the third part of the work have been analyzed statistical and stochastic methodologies in order to define the volume of the detention pond. In particular have been adopted the results of the long term simulation, performed with SWMM, to obtain the data to apply statistic and stochastic formulation. All these methodologies have been compared and correction coefficient have been proposed on the basis of the statistic and stochastic form. In this way engineers which have to design a detention pond can apply a simplified procedure appropriately corrected with the proposed coefficient.

Ruolo dell'Enantiomero (R)-9-HSA nel controllo della proliferazione in una linea di Adenocarcinoma del Colon umano

9-hydroxystearic acid (9-HSA) is an endogenous lipoperoxidation product and its administration to HT29, a colon adenocarcinoma cell line, induced a proliferative arrest in G0/G1 phase mediated by a direct activation of the p21WAF1 gene, bypassing p53. We have previously shown that 9-HSA controls cell growth and differentiation by inhibiting histone deacetylase 1 (HDAC1) activity, showing interesting features as a new anticancer drug. The interaction of 9-HSA with the catalytic site of the 3D model has been tested with a docking procedure: noticeably, when interacting with the site, the (R)-9-enantiomer is more stable than the (S) one. Thus, in this study, (R)- and (S)-9-HSA were synthesized and their biological activity tested in HT29 cells. At the concentration of 50 M (R)-9-HSA showed a stronger antiproliferative effect than the (S) isomer, as indicated by the growth arrest in G0/G1. The inhibitory effect of (S)-9-HSA on HDAC1, HDAC2 and HDAC3 activity was less effective than that of the (R)-9-HSA in vitro, and the inhibitory activity of both the (R)- and the (S)-9-HSA isomer, was higher on HDAC1 compared to HDAC2 and HDAC3, thus demonstrating the stereospecific and selective interaction of 9-HSA with HDAC1. In addition, histone hyperacetylation caused by 9-HSA treatment was examined by an innovative HPLC/ESI/MS method. Analysis on histones isolated from control and treated HT29 confirmed the higher potency of (R)-9-HSA compared to (S)-9-HSA, severely affecting H2A-2 and H4 acetylation. On the other side, it seemed of interest to determine whether the G0/G1 arrest of HT29 cell proliferation could be bypassed by the stimulation with the growth factor EGF. Our results showed that 9-HSA-treated cells were not only prevented from proliferating, but also showed a decreased [3H]thymidine incorporation after EGF stimulation. In this condition, HT29 cells expressed very low levels of cyclin D1, that didn’t colocalize with HDAC1. These results suggested that the cyclin D1/HDAC1 complex is required for proliferation. Furthermore, in the effort of understanding the possible mechanisms of this effect, we have analyzed the degree of internalization of the EGF/EGFR complex and its interactions with HDAC1. EGF/EGFR/HDAC1 complex quantitatively increases in 9-HSA-treated cells but not in serum starved cells after EGF stimulation. Our data suggested that 9-HSA interaction with the catalytic site of the HDAC1 disrupts the HDAC1/cyclin D1 complex and favors EGF/EGFR recruitment by HDAC1, thus enhancing 9-HSA antiproliferative effects. In conclusion 9-HSA is a promising HDAC inhibitor with high selectivity and specificity, capable of inducing cell cycle arrest and histone hyperacetylation, but also able to modulate HDAC1 protein interaction. All these aspects may contribute to the potency of this new antitumor agent.

Gli assetti proprietari e di controllo nell'agroalimentare italiano

The recent default of important Italian agri-business companies provides a challenging issue to be investigated through an appropriate scientific approach. The events involving CIRIO, FERRUZZI or PARMALAT rise an important research question: what are the determinants of performance for Italian companies in the Italian agri – food sector? My aim is not to investigate all the factors that are relevant in explaining performance. Performance depends on a wide set of political, social, economic variables that are strongly interconnected and that are often very difficult to express by formal or mathematical tools. Rather, in my thesis I mainly focus on those aspects that are strictly related to the governance and ownership structure of agri – food companies representing a strand of research that has been quite neglected by previous scholars. The conceptual framework from which I move to justify the existence of a relationship between the ownership structure of a company, governance and performance is the model set up by Airoldi and Zattoni (2005). In particular the authors investigate the existence of complex relationships arising within the company and between the company and the environment that can bring different strategies and performances. They do not try to find the “best” ownership structure, rather they outline what variables are connected and how they could vary endogenously within the whole economic system. In spite of the fact that the Airoldi and Zattoni’s model highlights the existence of a relationship between ownership and structure that is crucial for the set up of the thesis the authors fail to apply quantitative analyses in order to verify the magnitude, sign and the causal direction of the impact. In order to fill this gap we start from the literature trying to investigate the determinants of performance. Even in this strand of research studies analysing the relationship between different forms of ownership and performance are still lacking. In this thesis, after a brief description of the Italian agri – food sector and after an introduction including a short explanation of the definitions of performance and ownership structure, I implement a model in which the performance level (interpreted here as Return on Investments and Return on Sales) is related to variables that have been previously identified by the literature as important such as the financial variables (cash and leverage indices), the firm location (North Italy, Centre Italy, South Italy), the power concentration (lower than 25%, between 25% and 50% and between 50% and 100% of ownership control) and the specific agri – food sector (agriculture, food and beverage). Moreover we add a categorical variable representing different forms of ownership structure (public limited company, limited liability company, cooperative) that is the core of our study. All those variables are fully analysed by a preliminary descriptive analysis. As in many previous contributions we apply a panel least squares analysis for 199 Italian firms in the period 1998 – 2007 with data taken from the Bureau Van Dijck Dataset. We apply two different models in which the dependant variables are respectively the Return on Investments (ROI) and the Return on Sales (ROS) indicators. Not surprisingly we find that companies located in the North Italy representing the richest area in Italy perform better than the ones located in the Centre and South of Italy. In contrast with the Modigliani - Miller theorem financial variables could be significant and the specific sector within the agri – food market could play a relevant role. As the power concentration, we find that a strong property control (higher than 50%) or a fragmented concentration (lower than 25%) perform better. This result apparently could suggest that “hybrid” forms of concentrations could create bad functioning in the decision process. As our key variables representing the ownership structure we find that public limited companies and limited liability companies perform better than cooperatives. This is easily explainable by the fact that law establishes that cooperatives are less profit – oriented. Beyond cooperatives public limited companies perform better than limited liability companies and show a more stable path over time. Results are quite consistent when we consider both ROI and ROS as dependant variables. These results should not lead us to claim that public limited company is the “best” among all possible governance structures. First, every governance solution should be considered according to specific situations. Second more robustness analyses are needed to confirm our results. At this stage we deem these findings, the model set up and our approach represent original contributions that could stimulate fruitful future studies aimed at investigating the intriguing issue concerning the effect of ownership structure on the performance levels.

Controllo molecolare del differenziamento osteoblestico per applicazioni nel campo della rigenerazione del tessuto osseo

The aim of the study was to identify expression signatures unique for specific stages of osteoblast differentiation in order to improve our knowledge of the molecular mechanisms underlying bone repair and regeneration. We performed a microarray analysis on the whole transcriptome of human mesenchymal stem cells (hMSCs) obtained from the femoral canal of patients undergoing hip replacement. By defining different time-points within the differentiation and mineralization phases of hMSCs, temporal gene expression changes were visualised. Importantly, the gene expression of adherent bone marrow mononuclear cells, being the undifferentiated progenitors of bone cells, was used as reference. In addition, only the cultures able to form mineral nodules at the final time-point were considered for the gene expression analyses. To obtain the genes of our interest, we only focused on genes: i) whose expression was significantly upregulated; ii) which are involved in pathways or biological processes relevant to proliferation, differentiation and functions of bone cells; iii) which changed considerably during the different steps of differentiation and/or mineralization. Among the 213 genes identified as differentially expressed by microarray analysis, we selected 65 molecular markers related to specific steps of osteogenic differentiation. These markers are grouped into various gene clusters according to their involvement in processes which play a key role in bone cell biology such as angiogenesis, ossification, cell communication, development and in pathways like TGF beta and Wnt signaling pathways. Taken together, these results allow us to monitor hMSC cultures and to distinguish between different stages of differentiation and mineralization. The signatures represent a useful tool to analyse a broad spectrum of functions of hMSCs cultured on scaffolds, especially when the constructs are conceived for releasing growth factors or other signals to promote bone regeneration. Morover, this work will enhance our understanding of bone development and will enable us to recognize molecular defects that compromise normal bone function as occurs in pathological conditions.

Messa a punto di sistemi per il controllo e la terapia delle malattie virali

A livello globale una delle problematiche più urgenti della sanità pubblica umana e veterinaria è rappresentata dal controllo delle infezioni virali. L’emergenza di nuove malattie, la veloce diffusione di patologie finora confinate ad alcune aree geografiche, lo sviluppo di resistenza dei patogeni alle terapie utilizzate e la mancanza di nuove molecole attive, sono gli aspetti che influiscono più negativamente livello socio-economico in tutto il mondo. Misure per limitare la diffusione delle infezioni virali prevedono strategie per prevenire e controllare le infezioni in soggetti a rischio . Lo scopo di questa tesi è stato quello di indagare il possibile utilizzo di prototipi virali utilizzati come modello di virus umani per valutare l’efficacia di due diversi metodi di controllo delle malattie virali: la rimozione mediante filtrazione di substrati liquidi e gli antivirali di sintesi e di origine naturale. Per quanto riguarda la rimozione di agenti virali da substrati liquidi, questa è considerata come requisito essenziale per garantire la sicurezza microbiologica non solo di acqua ad uso alimentare , ma anche dei prodotti utilizzati a scopo farmaceutico e medico. Le Autorità competenti quali WHO ed EMEA hanno redatto delle linee guida molto restrittive su qualità e sicurezza microbiologica dei prodotti biologici per garantire la rimozione di agenti virali che possono essere trasmessi con prodotti utilizzati a scopo terapeutico. Nell'industria biomedicale e farmaceutica c'è l'esigenza di una tecnologia che permetta la rimozione dei virus velocemente, in grande quantità, a costi contenuti, senza alterare le caratteristiche del prodotto finale . La collaborazione con l’azienda GVS (Zola Predosa, Italia) ha avuto come obiettivo lo studio di una tecnologia di filtrazione che permette la rimozione dei virus tramite membrane innovative e/o tessuti-non-tessuti funzionalizzati che sfruttano l’attrazione elettrostatica per ritenere ed asportare i virus contenuti in matrici liquide. Anche gli antivirali possono essere considerati validi mezzi per il controllo delle malattie infettive degli animali e nell’uomo quando la vaccinazione non è realizzabile come ad esempio in caso di scoppio improvviso di un focolaio o di un attacco bioterroristico. La scoperta degli antivirali è relativamente recente ed il loro utilizzo è attualmente limitato alla patologia umana, ma è in costante aumento l’interesse per questo gruppo di farmaci. Negli ultimi decenni si è evidenziata una crescente necessità di mettere a punto farmaci ad azione antivirale in grado di curare malattie ad alta letalità con elevato impatto socio-economico, per le quali non esiste ancora un’efficace profilassi vaccinale. Un interesse sempre maggiore viene rivolto agli animali e alle loro patologie spontanee, come modello di studio di analoghe malattie dell’uomo. L’utilizzo di farmaci ad azione antivirale in medicina veterinaria potrebbe contribuire a ridurre l’impatto economico delle malattie limitando, nel contempo, la disseminazione dei patogeni nell’ambiente e, di conseguenza, il rischio sanitario per altri animali e per l’uomo in caso di zoonosi. Le piante sono sempre state utilizzate dall’industria farmaceutica per l’isolamento dei composti attivi e circa il 40% dei farmaci moderni contengono principi d’origine naturale. Alla luce delle recenti emergenze sanitarie, i fitofarmaci sono stati considerati come una valida per migliorare la salute degli animali e la qualità dei prodotti da essi derivati. L’obiettivo del nostro studio è stato indagare l’attività antivirale in vitro di estratti naturali e di molecole di sintesi nei confronti di virus a RNA usando come prototipo il Canine Distemper Virus, modello di studio per virus a RNA a polarità negativa, filogeneticamente correlato al virus del morbillo umano. La scelta di questo virus è dipesa dal fatto che rispetto ai virus a DNA e ai retrovirus attualmente l’offerta di farmaci capaci di contrastare le infezioni da virus a RNA è molto limitata e legata a molecole datate con alti livelli di tossicità. Tra le infezioni emergenti causate da virus a RNA sono sicuramente da menzionare quelle provocate da arbovirus. Le encefaliti virali da arbovirus rappresentano una emergenza a livello globale ed attualmente non esiste una terapia specifica. Una delle molecole più promettenti in vitro per la terapia delle infezioni da arbovirus è la ribavirina (RBV) che, con il suo meccanismo d’azione pleiotropico, si presta ad essere ulteriormente studiata in vivo per la sua attività antivirale nei confronti delle infezioni da arbovirus. Uno dei fattori limitanti l’utilizzo in vivo di questa molecola è l’incapacità della molecola di oltrepassare la barriera emato-encefalica. Nel nostro studio abbiamo messo a punto una formulazione per la somministrazione endonasale di RBV e ne abbiamo indagato la diffusione dalla cavità nasale all’encefalo attraverso l’identificazione e quantificazione della molecola antivirale nei diversi comparti cerebrali . Infine è stato condotto un esperimento in vivo per valutare l’efficacia di un composto a base di semi di Neem, di cui sono già note le proprietà antimicrobiche, nei confronti dell’infezione da orf virus, una zoonosi a diffusione mondiale, che ha un elevato impatto economico in aree ad alta densità ovi-caprina e può provocare lesioni invalidanti anche nell’uomo.

Sviluppo di modelli motore e veicolo per l'analisi di strategie di controllo in applicazioni Software e Hardware In the Loop

This work describes the development of a simulation tool which allows the simulation of the Internal Combustion Engine (ICE), the transmission and the vehicle dynamics. It is a control oriented simulation tool, designed in order to perform both off-line (Software In the Loop) and on-line (Hardware In the Loop) simulation. In the first case the simulation tool can be used in order to optimize Engine Control Unit strategies (as far as regard, for example, the fuel consumption or the performance of the engine), while in the second case it can be used in order to test the control system. In recent years the use of HIL simulations has proved to be very useful in developing and testing of control systems. Hardware In the Loop simulation is a technology where the actual vehicles, engines or other components are replaced by a real time simulation, based on a mathematical model and running in a real time processor. The processor reads ECU (Engine Control Unit) output signals which would normally feed the actuators and, by using mathematical models, provides the signals which would be produced by the actual sensors. The simulation tool, fully designed within Simulink, includes the possibility to simulate the only engine, the transmission and vehicle dynamics and the engine along with the vehicle and transmission dynamics, allowing in this case to evaluate the performance and the operating conditions of the Internal Combustion Engine, once it is installed on a given vehicle. Furthermore the simulation tool includes different level of complexity, since it is possible to use, for example, either a zero-dimensional or a one-dimensional model of the intake system (in this case only for off-line application, because of the higher computational effort). Given these preliminary remarks, an important goal of this work is the development of a simulation environment that can be easily adapted to different engine types (single- or multi-cylinder, four-stroke or two-stroke, diesel or gasoline) and transmission architecture without reprogramming. Also, the same simulation tool can be rapidly configured both for off-line and real-time application. The Matlab-Simulink environment has been adopted to achieve such objectives, since its graphical programming interface allows building flexible and reconfigurable models, and real-time simulation is possible with standard, off-the-shelf software and hardware platforms (such as dSPACE systems).

Struttura di popolazione in gamberi aristeidi (Decapoda, Aristeidae) nel Mediterraneo occidentale mediante l'utilizzo di loci microsatelliti

Il lavoro svolto durante il dottorato di ricerca ha permesso lo sviluppo e la verifica della attendibilità di marcatori molecolari neutrali (loci microsatelliti) specifici per Aristeus antennatus. Tali marcatori sono stati poi utilizzati per studiare la struttura genetica di popolazione della specie del Mediterraneo occidentale e i risultati ottenuti sono stati confrontati con quelli di un progetto di ricerca parallelo su Aristeaomorpha foliacea, analizzando differenze ed analogie fra le due specie. I risultati delle analisi su Aristeus antennatus hanno evidenziato una completa assenza di struttura di popolazione e come i due sessi contribuiscano in modo diverso al flusso genico. La specie infatti presenta un sex-ratio a favore dei maschi oltre gli 800m, mentre tale rappoorto è a favore delle femmine in strati più superficiali, dove sono probabilmente soggette a condizioni oceanografiche più dispersive. Tramite test genetici appropriati è stato possibile valutare indirettamente il grado di dospersione dei sessi dimostrando che nell'area analizzati i maschi erano rappresentati maggiormente da individui stanziali, mentre gli individui di sesso femminile erano migranti. Le femmine appaiono pertanto giocare un ruolo preminente rispetto ai maschi nel determinare l'entità del flusso genico. Il confronto dei risultati ottenuti in Aristeus antennatus con quelli di Aristaeomorpha foliacea ha evidenziato la relazione fra alta capacità dispersiva, sia allo stato larvale che adulto, e completo rimescolamento genetico nei gamberi aristeidi nel Mediterraneo occidentale anche se in quest'ultima specie non ci sono evidenze di dispersione genetica mediata dal sesso. E' pertanto di forte interesse (dato anche il valore economico di questi organismi) come una struttura di popolazione qualitativamente e quantitavamente comporabile venga raggiunta con dinamiche di popolazione molto diverse.