Portable smart films for ultrasensitive detection and chemical analysis using SERS and SERRS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Portable MP3 player as low-cost data logger

Non-audio signals have been recorded in the flash ROM memory of a portable MP3 player, in WAV format file, to examine the possibility of using these cheap and small instruments as general-purpose portable data loggers. A 1200-Hz FM carrier modulated by the non-audio signal has replaced the microphone signal, while using the REC operating mode of the MP3 player, which triggers the voice recording function. The signal recovery was carried out by a PLL-based FM demodulator whose input is the FM signal captured in the coil leads of the MP3 player's earphone. Sinusoidal and electrocardiogram signals have been used in the system evaluation. Although the quality of low frequency signals needs improvement, overall the results indicate the viability of the proposal. Suggestions are made for improvements and extensions of the work.

Evaluation of a portable clinical analyzer for the determination of blood gas partial pressures, electrolyte concentrations, and hematocrit in venous blood samples collected from cattle, horses, and sheep

Objective To compare results reported for blood gas partial pressures, electrolyte concentrations, and Hct in venous blood samples collected from cattle, horses, and sheep and analyzed by use of a portable clinical analyzer (PCA) and reference analyzer (RA).Animals-Clinically normal animals (24 cattle, 22 horses, and 22 sheep).Procedures-pH; Pco(2); Po(2); total carbon dioxide concentration; oxygen saturation; base excess; concentrations of HCO(3)(-), Na(+), K(+), and ionized calcium; Hct; and hemoglobin concentration were determined with a PCA. Results were compared with those obtained for the same blood sample with an RA. Bias (mean difference) and variability (95% confidence interval) were determined for all data reported. Data were also subjected to analyses by Deming regression and Pearson correlation.Results-Analysis of Bland-Altman plots revealed good agreement between results obtained with the PCA and those obtained with the RA for pH and total carbon dioxide concentration in cattle, K(+) concentration in horses and sheep, and base excess in horses. Except for Na(+) concentration and Hct in horses and sheep, correlation was good or excellent for most variables reported.Conclusions and Clinical Relevance-Data from blood gas and electrolyte analyses obtained by use of the PCA can be used to evaluate the health status of cattle, horses, and sheep. Furthermore, the handheld PCA device may have a great advantage over the RA device as a result of the ability to analyze blood samples on farms that may be located far from urban centers. (Am J Vet Res 2010;71:515-521)

Rugged, Portable Tungsten Coil Atomic Emission Spectrometer

Tungsten coil atomic emission spectrometry is an ideal technique for field applications because of its simplicity, low cost, low power requirement, and independence from cooling systems. A new, portable, compact design is reported here. The tungsten coil is extracted from an inexpensive 24 V, 250 W commercial light bulb. The coil is housed in a small, aluminum cell. The emission signal exits from a small aperture in the cell, while the bulk of the blackbody emission from the tungsten coil is blocked. The resulting spectra exhibit extremely low background signals. The atomization cell, a single lens, and a hand-held charge coupled device (CCD) spectrometer are fixed on a 1 x 6 x 30 cm ceramic base. The resulting system is robust and easily transported. A programmable, miniature 400 W solid-state constant current power supply controls the temperature of the coil. Fifteen elements are determined with the system (Ba, Cs, Li, Rb, Cr, Sr, Eu, Yb, Mn, Fe, Cu, Mg, V, Al, and Ga). The precision ranges from 4.3% to 8.4% relative standard deviation for repetitive measurements of the same solution. Detection limits are in the 0.04 to 1500 mu g/L range. Accuracy is tested using standard reference materials for polluted water, peach leaves, and tomato leaves. For those elements present above the detection limit, recoveries range from 72% to 147%.

Multivariate quality control studies applied to Ca(II) and Mg(II) determination by a portable method

A portable or field test method for simultaneous spectrophotometric determination of calcium and magnesium in water using multivariate partial least squares (PLS) calibration methods is proposed. The method is based on the reaction between the analytes and methylthymol blue at pH 11. The spectral information was used as the X-block, and the Ca(II) and Mg(II) concentrations obtained by a reference technique (ICP-AES) were used as the Y-block. Two series of analyses were performed, with a month's difference between them. The first series was used as the calibration set and the second one as the validation set. Multivariate statistical process control (MSPC) techniques, based on statistics from principal component models, were used to study the features and evolution with time of the spectral signals. Signal standardization was used to correct the deviations between series. Method validation was performed by comparing the predictions of the PLS model with the reference Ca(II) and Mg(II) concentrations determined by ICP-AES using the joint interval test for the slope and intercept of the regression line with errors in both axes. (C) 1998 John Wiley & Sons, Ltd.

Portable Hardness tester for timber classification

Hardness is a property largely used in material specifications, mechanical and metallurgical research and quality control of several materials. Specifically for timber, Janka hardness is a simple, quick and easy test, with good correlations with the compression parallel to grain strength, a strong reference in structural classification for this material. More recently, international studies have reported the use of Brinell hardness for timber assessment which resumes the advantages previously mentioned for Janka hardness and make it easier to be performed in the field, especially because of the lower magnitude of the involved loads. A first generation of an equipment for field evaluation of hardness in wood - Portable Hardness tester for wood - based on Brinell hardness has already been developed by the Research Group on Forest Products from FCA/UNESP, Brazil, with very good correlations between the evaluated hardness and several other mechanical properties of the material when performing tests with different species of native and reforested wood (traditionally used as ties - sleepers - in railways). This paper presents results obtained in the experimental program with the first generation of this equipment and preliminary tests with its second generation, which uses accelerometers to substitute the indentation measurements in wood. For the first generation of the equipment functional and calibration tests were carried out using 16 native and reforestation timber lots, among there E. citriodora, E. tereticornis, E. saligna, E. urophylla, E. grandis, Goupia glabra and Bagassa guianenses, with different origins and ages. The results obtained confirm its potential in the classification of specimens, with inclusion errors varying from 4.5% to 16.6%.

Capillary blood glucose and venous blood glucose measured with portable digital glucometer in diabetic dogs

This study aimed to compare the glycemic values obtained with a glucometer with those determined by a colorimetric enzymatic assay in venous blood as well as to evaluate the possibility of using capillary blood samples of dogs with diabetes mellitus. A group with 30 diabetic dogs was formed and from each dog three blood samples were obtained for glycemic evaluations by different methods and blood collection sites. The mean glycemic values showed no significant difference between the different sites of blood collection and methods (P=0.90). Venous, pinna and carpal pad blood glucose showed excellent correlation with the colorimetric enzymatic assay (r=0.98; r=0.95 and r=0.96 respectively) and the obtained values fit properly the clinically acceptable intervals in the error grid analysis. The present study revealed that carpal pad, venous and pinna glucose measurements are clinically acceptable and this method is feasible for use in hospitalized diabetic dogs. The sample attainment of carpal pad proved to be effective and a viable alternative. Further work is necessary to assess the utility of this technique in a home environment.

Estimating hardness of eucalyptus wood with a portable hardness tester

More than 80% of the 29600 km of the Brazilian railroad mesh employs wooden sleepers. The problem of hard availability of native wood for this purpose leads to the alternative use of reforestation species to produce sleepers. Considering the great difficulty to, in field condition, evaluate characteristics that are of major importance to define its suitability to sleeper production the Research Group on Forest Products from FCA/UNESP - Brazil had developed equipment for field evaluation of hardness in wood - Portable Hardness Tester. This paper reports the functional validation tests, performed with different species of Eucalyptus. Results revealed the equipment great functionality, easy-to-use characteristics and applicability to Eucalyptus wood. Moderate to strong relationships between laboratory and validated values of hardness were found. The best validation model was obtained using the data provided by the experimental dispositive 3 (R2=0.74 and SSE= 7.71 kJ/m2) while the experimental dispositive 1 gave the worse validation (R2=0.55 and SSE= 13.46 kJ/m2).

A novel LTCC electrochemical cell construction and characterization: A detection compartment for portable devices

In this work we described for the first time the construction of a 25 μL electrochemical cell from low temperature co-fired ceramic (LTCC) material and carbon screen-printed electrode applicable in portable devices. Firstly, a carbon screen-printed electrode was prepared and characterized by cyclic voltammetry and scanning electron microscopy. Afterwards carbon polymeric film and metal pastes were dropped into the LTCC cell cavities in order to determine the device electrodes, and this arrangement was also electrochemically characterized. The great advantage of this promising device is the simple construction method and its widespread applicability in reusable portable devices. © 2013 The Royal Society of Chemistry.

Portable meters for nutritional assessment in plants of gerbera fertigated with electrical conductivity levels

Rapid tests to assess the nutritional status of plants gerbera can make easier the decision of any adjustments in the fertilization of the substrate. The study was conducted to evaluate nutritionally fertigated gerbera plants with increasing levels of electrical conductivity (EC), using portable meters nitrate and potassium, and chlorophyll. For this, two experiments were conducted. A randomized block design with five levels of EC (0.5, 2.0, 3.5, 5.0 and 6.5 dS m-1) and four replications was used. Cherry cultivar was used in the first experiment. In the second experiment, two cultivars (Cherry and Salmon Rose) were used. In the first experiment, the sap of the leaves was subjected to rapid testing of N-NO3- (equipment Cardy Horiba C -141). N-NO3- and K+ (C-131) were determined in the substrate solution. The intensity of the green leaf, in the second experiment was evaluated with portable Chlorophyll Meter. The N content in the indicator leaf in the first and N and K contents in the plant in the second experiment were determined. Rapid tests are presented as good indicators of the level of N-NO3- and K+ in plant tissue, with the advantages of convenience and speed of determination, facilitating monitoring of fertilization of the substrate by producers and technicians.

A simple and portable instrument for determination of captopril in pharmaceutical formulations

Objective: This article describes the application and the performance of a cheap, simple and portable device that can be used for colorimetric quantitative determination of captopril (CPT) in pharmaceutical preparations. Methods: The sensor is a light detector resistor (LDR) placed into a black PTFE cell and coupled to a low cost multimeter (Ohmmeter). The instrument has been tested and is easy and fast to use. The quantitative study is based mainly on reduction of ammonium molybdate by captopril, in the presence of sulphuric acid, producing a green-yellow compound (max 407 nm). The calibration curves were obtained by plotting the electric resistance of the LDR against the CPT concentration on the range of 4.60 x 10-4 to 1.84 x 10-3 mol l-1 with a good coefficient of determination (R2 = 0.9962). Results: Statistical analysis of the obtained results showed no significant difference between the proposed methodology and the official reported method as evident from the t-test and variance ratio at 95% confidence level. Conclusion: The results of this study demonstrate that the instrument can be used for simple, accurate, precise, fast, in situ and low-cost colorimetric analysis of captopril in pharmaceuticals products.

Efeitos da aplicação de herbicidas sobre a eficiência fotoquímica em plantas de soja convencional e geneticamente modificada

Objetivou-se, neste trabalho, avaliar o efeito da aplicação de herbicidas em pós-emergência sobre a eficiência fotoquímica de duas cultivares de soja (M-SOY 7908 RR e M-SOY 8001). O delineamento experimental utilizado foi em blocos ao acaso, com quatro repetições. Os tratamentos constaram da aplicação de herbicidas isolados e em misturas: lactofen, glyphosate, lactofen + chlorimuron-ethyl, chlorimuron-ethyl + imazethapyr, chlorimuron-ethyl + bentazon, glyphosate + imazethapyr, lactofen + chlorimuron-ethyl + imazethapyr e lactofen + chlorimuron-ethyl + imazethapyr/haloxyfop-methyl. Além disso, foram mantidas duas testemunhas sem aplicação de herbicida. As avaliações foram realizadas aos 4; 11; 18; 25 e 32 dias após aplicação dos herbicidas (DAA) no primeiro ano, e aos 6, 14, 21, 28 e 35 DAA, no segundo. A cultivar M-SOY 8001 foi suscetível à aplicação dos herbicidas, principalmente às misturas contendo lactofen + chlorimuron-ethyl e lactofen + chlorimuron-ethyl + imazethapyr + haloxifop-methyl, os quais provocaram redução no rendimento quântico máximo do PSII (Fv/Fm). As duas cultivares apresentaram suscetibilidade aos herbicidas quando tratados com lactofen aplicado isolado e nas misturas lactofen + chlorimuron-ethyl, chlorimuron-ethyl + imazethapyr, lactofen + chlorimuron-ethyl + imazethapyr e lactofen + chlorimuron-ethyl + imazethapyr + haloxifop-methyl com redução nos teores de clorofila, estimados pelo Medidor Portátil de Clorofilas. Os danos foram reversíveis, desaparecendo gradativamente com a idade das plantas.

Eficiência fotossintética de cultivares de cana-de-açúcar e de diferentes espécies de plantas daninhas após a aplicação do diuron

O objetivo deste trabalho foi avaliar a eficiência fotossintética, através da taxa de transporte de elétrons, de seis espécies de plantas daninhas e três cultivares de cana-de-açúcar após aplicação do herbicida diuron em pós-emergência inicial. Os cultivares utilizados (PO8862, SP80-3280 e RB83-5486) foram cortados em gemas e plantados em vasos com capacidade de 12 litros. A semeadura das seis espécies de plantas daninhas - Brachiaria decumbens, Digitaria horizontalis, Panicum maximum, Ipomoea grandifolia, Ipomoea hederifolia e Merremia cissoides - foi realizada para obter 25 plantas por vaso. A aplicação do herbicida diuron em pós-emergência inicial das plantas daninhas e dos cultivares de cana-de-açúcar foi realizada na dose de 3,0 kg ha-1, com adição de 0,2% de surfatante. As avaliações da taxa de transporte de elétrons no fotossistema (ETR) das plantas após a aplicação foram realizadas com auxílio de um fluorômetro portátil. Para as espécies de plantas daninhas, a ETR foi avaliada após intervalos de 2, 4, 24, 48, 72, 96 e 144 horas após a aplicação. Quanto aos cultivares de cana-de-açúcar, os intervalos avaliados foram de 2, 24, 48, 72, 120, 168 e 240 horas após a aplicação. de maneira geral, as reduções dos valores da ETR indicaram o nível de sensibilidade dos diferentes cultivares de cana-de-açúcar e das diferentes plantas daninhas ao diuron, e a intoxicação foi detectada antes ou mesmo sem a presença dos sintomas. A classificação da sensibilidade dos cultivares de cana-de-açúcar foi em ordem decrescente: PO-8862, SP80-3280 e RB83-5486; para as plantas daninhas, as espécies mais sensíveis foram M. cissoides, I. grandifolia e I. hederifolia, seguidas das gramíneas D. horizontalis, P. maximum e B. decumbens.

Avaliação da intoxicação de cultivares de cana-de-açúcar e I. grandifolia ao amicarbazone

O objetivo deste trabalho foi avaliar a intoxicação de planta daninha e cultivares de cana-de-açúcar ao amicarbazone. Para isso, utilizou-se Ipomoea grandifolia como planta daninha representante e os cultivares de cana-de-açúcar PO8862, SP80 3280 e RB83 5486, caracterizados como sensível, intermediário e tolerante aos herbicidas, respectivamente. Foi verificado o consumo de água e quantificada a concentração do amicarbazone em seiva de xilema dos três cultivares de cana-de-açúcar e de I. grandifolia por meio da bomba de Schollander e da cromatografia e espectrometria de massas (LC-MS). A intoxicação das plantas foi verificada através de leituras da fluorescência, com auxílio do fluorômetro portátil, que permitiu a correlação da taxa de transporte de elétrons (ETR) com a concentração de amicarbazone absorvido pelos cultivares de cana-de-açúcar e por I. grandifolia. Verificou-se, através do experimento, que a redução dos valores da ETR pode ser utilizada para indicar o nível de intoxicação de I. grandifolia e de plantas de cana-de-açúcar ao amicarbazone. I. grandifolia destacou-se em relação à cana-de-açúcar pela maior sensibilidade ao amicarbazone. A suscetibilidade diferencial dos cultivares de cana-de-açúcar PO8862, SP80 3280 e RB83 5486 pode ser justificada, possivelmente, pela absorção diferencial do amicarbazone entre os cultivares.