Análise tridimensional de esforços em elementos rompedores de semeadoras de plantio direto

As informações da avaliação de mecanismos de abertura de sulco de semeadoras de plantio direto auxiliam as empresas no dimensionamento de ferramentas rompedoras do solo, que buscam menor requerimento energético. Este trabalho foi realizado num solo classificado como Latossolo Vermelho com o objetivo de avaliar tridimensionalmente os esforços dos mecanismos de abertura de sulco de semeadoras adubadoras de plantio direto. O delineamento experimental utilizado foi o de blocos ao acaso com cinco tratamentos, sendo cinco mecanismos de abertura de sulco (disco liso - DL, disco corrugado - DC, disco ondulado - DO, disco duplo - DD e haste sulcadora - H). Para mensurar os esforços dos mecanismos de abertura de sulco, foi utilizado um dinamômetro com sensibilidade nas direções horizontal, transversal e vertical e no momento fletor e torsor. A avaliação mostrou que a interação entre mecanismos de abertura de sulco e carga vertical não foi significativa, entretanto os fatores foram significativos quando analisados individualmente. O resultado individual dos mecanismos de abertura de sulco mostrou que o disco ondulado proporcionou maior área de mobilização do solo, a haste sulcadora apresentou o menor valor de força vertical e o disco duplo e a haste sulcadora obtiveram o menor esforço horizontal.

Experimental study of the conventional equation to determine a plate's moment of inertia

In this work, we describe an experimental setup in which an electric current is used to determine the angular velocity attained by a plate rotating around a shaft in response to a torque applied for a given period. Based on this information, we show how the moment of inertia of a plate can be determined using a procedure that differs considerably from the ones most commonly used, which generally involve time measurements. Some experimental results are also presented which allow one to determine parameters such as the exponents and constant of the conventional equation of a plate's moment of inertia.

Experimental study of the moment of inertia of a cone - angular variation and inertia ellipsoid

In this paper, an experimental set-up which differs from the traditional ones is established in order to determine the moment of inertia of a right circular cone. Its angular variation and inertia ellipsoid are determined by means of an experimental study. In addition, a system that allows for the evaluation of the angular acceleration and torque through electric current or frequency measurement is utilized.

Electric charge quantization and the muon anomalous magnetic moment

We investigate some proposals to solve the electric charge quantization puzzle that simultaneously explain the recent measured deviation on the muon anomalous magnetic moment. For this we assess extensions of the electro-weak standard model spanning modifications on the scalar sector only. It is interesting to verify that one can have modest extensions which easily account for the solution for both problems.

Effect of the composite surface sealant application moment on marginal sealing of compactable composite resin restoration

An analysis was carried out to observe whether the application or not of a composite surface sealant (CSS), as well the moment for CSS application were able to reduce marginal microleakage in compactable composite resin restoration. All the preparations were restored with a compactable composite resin. The restored teeth were randomly assessed. G1 (control group): finished and polished; G2: finished, polished, etched and cover with CSS; G3: immediately after the restoration done the CSS was applied, then finished and polished; G4: CSS applied immediately after the restoration was done, the finished and polished, etched, and covered with CSS. The specimens were isolated with nail polish, thermocycled, immersed in aqueous solution of silver nitrate, and followed in a photo developing solution. The microleakage scores obtained from the occlusal and cervical walls were analyzed with the Kruskall-Wallis nonparametric test. No microleakage was found at the enamel margins. Comparing the microleakage scores at dentin/cementum margins (p < 0.05) it was found that G3 (p = 0.0162) and G4 (p = 0.0187) were able to reduce microleakage when compared with group G2. However the results were not statistically different from the control group. The application of CSS was not able to completely eliminate marginal microleakage at the dentin/cementum margins.

Compositeness effects in the anomalous weak-magnetic moment of leptons

We investigate the effects induced by excited leptons, at the one-loop level, in the anomalous magnetic and weak-magnetic form factors of the leptons. In particular, we compute their contributions to the weak-magnetic moment of the tau lepton, which can be measured on the Z peak, and we compare it with the contributions to g(mu) - 2, measured at low energies.

Szego polynomials and the truncated trigonometric moment problem

We show how Szego polynomials can be used in the theory of truncated trigonometric moment problem.

On a moment problem associated with Chebyshev polynomials

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Group A T-loop for differential moment mechanics: An implant study

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Optimal moment to change pressure regulator and sprayer kit on center pivot irrigation machines: a theoretical proposal

A theoretical model was developed in order to determine the optimal moment for substituting the sprayer and pressure regulator kit on a center pivot irrigation machine. The model is based on the hypothesis that pressure regulator and sprayer deterioration decrease irrigation uniformity. To compensate the deficit that happens at under irrigated areas, an increase on irrigation depth is required. The model considers: additional water consumption and energy costs, maintenance and labor costs, as well as yield losses associated with under or over irrigated areas. The sum of all these components is compared to buying and installing a new spray kit cost, allowing the farmer to decide the best moment to renovate the sprayer and pressure regulator kits on a center pivot irrigation machine based on economic criteria.

Optimal moment to change pressure regulator and sprayer kit on center pivot irrigation machines: application to a study case

A theoretical model developed by the authors for determining the optimal moment to substitute sprayer and pressure regulator kit on a center pivot irrigating potatoes and beans has been applied. The methodology compares the sum of the costs due to additional consumption of water and energy, maintenance and labor, as well as yield losses associated to areas with deficit or over irrigation to the costs due to buy and install a new sprinkling set on the pivot. The results showed that for a reduction of 3.07% of the Hermann and Hein’s Uniformity Coefficient (UCh), the substitution of the sprinkling module on the pivot is justified when potatoes and beans are cultivated.

Nonlinear dynamical analysis of an aeroelastic system with multi-segmented moment in the pitch degree-of-freedom

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)