Microstructure evolution during warm deformation of low carbon steel with dispersed cementite

The microstructure evolution and mechanical behavior during large strain of a 0.16%C-Mn steel has been investigated by warm torsion tests. These experiments were carried out at 685°C at equivalent strain rate of 0.1 s . The initial microstructure composed of a martensite matrix with uniformly dispersed fine cementite particles was attained by quenching and tempering. The microstructure evolution during tempering and straining was performed through interrupted tests. As the material was reheated to testing temperature, well-defined cell structure was created and subgrains within lath martensite were observed by TEM; strong recovery took place, decreasing the dislocation density. After 1 hour at the test temperature and without straining, EBSD technique showed the formation of new grains. The flow stress curves measured had a peculiar shape: rapid work hardening to a hump, followed by an extensive flow-softening region. 65% of the boundaries observed in the sample strained to ε = 1.0 were high angle grain boundaries. After straining to ε = 5.0, average ferrite grain size close to 1.5 μm was found, suggesting that dynamic recrystallization took place. Also, two sets of cementite particles were observed: large particles aligned with straining direction and smaller particles more uniformly dispersed. The fragmentation or grain subdivision that occurred during reheating and tempering time was essential for the formation of ultrafine grained microstructure.

Kinetics of martensite decomposition in the Cu-9Al-6Ag alloy

The non-occurrence of the beta' -> (alpha+ gamma(1)) decomposition reaction in the Cu-9 wt.% Al-6 wt.% Ag alloy, on ageing between 200 and 450 degrees C, is discussed considering the influence of Ag on point defects redistribution and energy difference between martensite and the ordered parent phase. (c) 2005 Elsevier B.V All rights reserved.

Martensite aging kinetics in the Cu-10 wt.%Al and Cu-10 wt.%Al-10 wt.%Ag alloys

The martensite aging kinetics in the Cu-10 wt.%Al and Cu-10 wt.%Al-10 wt.%Ag alloys was studied using microhardness measurements, classical differential thermal analysis (DTA), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and in-situ high-temperature X-ray diffractometry (XRD). The results for the Cu-10%Al alloy indicated a process dominated by the martensite ordering assisted by migration of quenched-in vacancies and followed by the consumption of the α phase. For the Cu-10%Al-10%Ag alloy the dominant process is the consumption of the α phase associated with a decrease in the ordering degree of the martensitic phase. © 2007 Springer Science+Business Media, LLC.

On the electrochemical behavior of Cu-16%Zn-6.5%Al alloy containing the β'-phase (martensite) in borate buffer

In this work, the electrochemical behavior of Cu-16(wt.%)Zn-6.5(wt.%)Al alloy containing the β'-phase (martensite) was studied in borate buffer solution (pH 8.4) by means of open-circuit potential (EOC), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The alloy EOC was -0.29 V vs. Hg/HgO/OH-, similar to that of pure copper in this medium, indicating that the processes which occur on the alloy surface are mainly governed by copper. EIS response was related to the dielectric and transmission properties of the complex oxide layer. The CVs showed peaks concerning the redox reactions for copper and zinc. These peaks were assigned to the formation and reduction of copper and zinc species. Furthermore, they showed that the copper oxidation was suppressed by the presence of zinc and aluminum in the alloy composition. The copper and zinc oxidation to form complex oxide layers and the reduction of the different metallic oxides generated in the anodic potential scan suggest that a solid state reaction could determine the metallic oxide formation. © 2013 Elsevier Ltd. All rights reserved.

Martensite decomposition in Cu-Al-Mn-Ag alloys

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of wounds applied to the bases of herbaceous cuttings on the rooting of four Japanese apricot clones (Prunus mume Sieb. et Zucc.) in an intermittent mist system

The Japanese apricot (Prunus mume Sieb. et Zucc.) is a fruit tree of the Rosaceae family which produces very acid and bitter fruits, highly appreciated by Orientals. In Brazil, this species has been studied as a rootstock for peach and nectarine trees, its main advantage being the reduction in plant vigour, which can favour the production of compact trees and orchard cultural treatments. This study was conducted in the Vegetable Production Department of FCAV/UNESP, Jaboticabal Campus, São Paulo State, Brazil, and the objective was to examine the effect of wounding the herbaceous cutting bases on the rooting of four Japanese apricot clones. The clones were obtained from plants under cultivation in the Instituto Agronomico de Campinas, Brazil, and were identified as Clones 02, 05, 10 and 15. The stock plants, obtained through herbaceous cuttings, were maintained under lath house conditions (50% of natural light). Cuttings 12 cm long with 3 to 5 leaves were collected from these clones and prepared. The experiment was carried out in a completely randomised design with 4 repetitions of 20 cuttings per replication, in a factorial 4 x 2 design, the clone factor having 4 levels (Clones 02, 05, 10 and 15) and the wounding factor at 2 levels of incisions into the cutting base (with and without). All the cuttings were treated with 2000 mg.L-1 of IBA for five seconds. Differences between the clones were observed concerning the rooting percentage, dead cuttings, number and length of roots. The incision (wound) at the base of the herbaceous cuttings of the Japanese apricot increased the number of roots and improved the distribution of these in the damaged tissue but the results were not considered sufficiently beneficial to make the treatment worthwhile.

Influência da fonte material e do tempo de cura na propagação vegetativa da pitaya vermelha (Hylocereus undatus Haw)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comportamento plástico do aço inoxidável austenítico em baixa temperatura

Ensaios de tração uniaxiais foram empregados para deformar aços inoxidáveis austeníticos do tipo 304, em diferentes temperaturas abaixo da ambiente (de 77 K a 300 K). A relação entre a estabilidade da austenita e o encruamento, em função da temperatura de teste, é discutida quanto à transformação martensítica induzida por deformação e ao deslizamento de discordâncias na austenita. em curvas tensão-deformação que assumem a equação de Ludwik sigma = sigmao + képsilonn, na qual sigma é a tensão verdadeira e e a elongação plástica verdadeira, um modo conveniente para analisar o encruamento é por meio do diagrama log dsigma / dépsilon versus log épsilon. O aspecto significativo é a variação da taxa de encruamento dsigma / dépsilon com a elongação plástica verdadeira nas diferentes temperaturas. As mudanças no comportamento do encruamento motivando até três estágios de deformação são associadas a diferentes processos microestruturais. A transformação martensítica pode ser considerada como um processo de deformação que compete com o processo usual de deslizamento. A investigação desses estágios, na região plástica, produz uma referência qualitativa de como diferentes fatores, tais como o grau de deformação, temperatura e composição química da austenita, afetam a transformação austenita-martensita.

Substratos e regulador vegetal no enraizamento de estacas de pitaya

A pitaya é uma cactácea originária das florestas tropicais americanas que produz frutos exóticos bem apreciados e comercializados, principalmente no continente asiático. Contudo, ainda é uma espécie vegetal que demanda informações técnicas de cultivo nas áreas agrícolas brasileiras, motivando pesquisas em várias áreas do conhecimento. Objetivou-se avaliar diferentes substratos no enraizamento de cladódios imersos e não imersos no regulador de crescimento, ácido naftalenacético (ANA), na formação e desenvolvimento inicial de raízes em estacas de Hylocereus undatus, resultando em mudas mais vigorosas e de melhor qualidade. O experimento foi conduzido sob ripado no Departamento de Produção Vegetal - setor de Horticultura da Faculdade de Ciências Agronômicas no campus de Botucatu - UNESP. O delineamento experimental foi o inteiramente aleatorizado em esquema fatorial 4 x 2 (substratos x condições) com quatro repetições. Após 60 dias da instalação do experimento foram avaliados: massa fresca e seca da parte aérea, massa fresca e seca das raízes e o comprimento da maior raiz. O crescimento e desenvolvimento radicular inicial de mudas não são influenciados pelo regulador vegetal ANA. Os substratos com a presença de areia são os mais adequados para a formação de mudas vigorosas e de boa qualidade. A mistura areia + esterco bovino proporciona maior acúmulo de fitomassa no sistema radicular de pitaya (H. undatus).

CMS physics technical design report, volume II: Physics performance

CMS is a general purpose experiment, designed to study the physics of pp collisions at 14 TeV at the Large Hadron Collider ( LHC). It currently involves more than 2000 physicists from more than 150 institutes and 37 countries. The LHC will provide extraordinary opportunities for particle physics based on its unprecedented collision energy and luminosity when it begins operation in 2007. The principal aim of this report is to present the strategy of CMS to explore the rich physics programme offered by the LHC. This volume demonstrates the physics capability of the CMS experiment. The prime goals of CMS are to explore physics at the TeV scale and to study the mechanism of electroweak symmetry breaking - through the discovery of the Higgs particle or otherwise. To carry out this task, CMS must be prepared to search for new particles, such as the Higgs boson or supersymmetric partners of the Standard Model particles, from the start- up of the LHC since new physics at the TeV scale may manifest itself with modest data samples of the order of a few fb(-1) or less. The analysis tools that have been developed are applied to study in great detail and with all the methodology of performing an analysis on CMS data specific benchmark processes upon which to gauge the performance of CMS. These processes cover several Higgs boson decay channels, the production and decay of new particles such as Z' and supersymmetric particles, B-s production and processes in heavy ion collisions. The simulation of these benchmark processes includes subtle effects such as possible detector miscalibration and misalignment. Besides these benchmark processes, the physics reach of CMS is studied for a large number of signatures arising in the Standard Model and also in theories beyond the Standard Model for integrated luminosities ranging from 1 fb(-1) to 30 fb(-1). The Standard Model processes include QCD, B-physics, diffraction, detailed studies of the top quark properties, and electroweak physics topics such as the W and Z(0) boson properties. The production and decay of the Higgs particle is studied for many observable decays, and the precision with which the Higgs boson properties can be derived is determined. About ten different supersymmetry benchmark points are analysed using full simulation. The CMS discovery reach is evaluated in the SUSY parameter space covering a large variety of decay signatures. Furthermore, the discovery reach for a plethora of alternative models for new physics is explored, notably extra dimensions, new vector boson high mass states, little Higgs models, technicolour and others. Methods to discriminate between models have been investigated. This report is organized as follows. Chapter 1, the Introduction, describes the context of this document. Chapters 2-6 describe examples of full analyses, with photons, electrons, muons, jets, missing E-T, B-mesons and tau's, and for quarkonia in heavy ion collisions. Chapters 7-15 describe the physics reach for Standard Model processes, Higgs discovery and searches for new physics beyond the Standard Model.

Search for narrow resonances in dilepton mass spectra in pp collisions at root s=7 TeV CMS Collaboration

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Search for the standard model Higgs boson decaying to bottom quarks in pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

First measurement of hadronic event shapes in pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Search for charge-asymmetric production of W ' bosons in t(t)over-bar + jet events from pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Search for physics beyond the standard model using multilepton signatures in pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)