Fuzzy control embedded in microcontroller and applied to an experimental apparatus using magnetorheological fluid damper

This work focuses on applying fuzzy control embedded in microcontrollers in an experimental apparatus using magnetorheological fluid damper. The non-linear behavior of the magnetorheological dampers associated with the parametric variations on vehicle suspension models corroborate the use of the fuzzy controllers. The fundamental formulation of this controller is discussed and its performance is shown through numeric simulations. An experimental apparatus representing a two degree of freedom system containing a magnetorheological damper is used to identify the main parameters and to evaluate the performance of the closed-loop system with the embedded low-cost microcontroller-based fuzzy controller. © 2013 Brazilian Society for Automatics - SBA.

Determination of minimum fluidization velocity for gas-solid beds by experimental data and numerical simulations

The purpose of this work is to predict the minimum fluidization velocity Umf in a gas-solid fluidized bed. The study was carried out with an experimental apparatus for sand particles with diameters between 310μm and 590μm, and density of 2,590kg/m3. The experimental results were compared with numerical simulations developed in MFIX (Multiphase Flow with Interphase eXchange) open source code [1], for three different sizes of particles: 310mum, 450μm and 590μm. A homogeneous mixture with the three kinds of particles was also studied. The influence of the particle diameter was presented and discussed. The Ergun equation was also used to describe the minimum fluidization velocity. The experimental data presented a good agreement with Ergun equation and numerical simulations. Copyright © 2011 by ASME.

Uma abordagem teórica e experimental do oscilador harmônico em duas dimensões utilizando as curvas de Lissajous

The study of oscillatory phenomena is an important topic in several areas of knowledge. The understanding and the solution of many problems that scientists and engineers confront nowadays can be formulated, at least as an analogy, in terms of an oscillatory movement. The description of the motion of this nature has remarkable contributions to the mathematical and conceptual formation of the students and for solving daily problems in several areas. In this paper we propose a theoretical and experimental approach involving the phenomenon of harmonic oscillations in two dimensions. Lissajous curves were used as experimental demonstration of the resulting trajectories. These curves were obtained from relatively simple experimental apparatus, which is affordable in most teaching laboratories of physics.

Numerical and experimental investigations of three-dimensional container filling with Newtonian viscous fluids

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Implementação de aparato experimental para medição de instabilidades tipo Roll Waves em fluidos não- newtonianos

Pós-graduação em Engenharia Mecânica - FEIS

Refrigerator COP with thermal storage

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Pressure drop correlation for oil-refrigerant R134a mixture flashing flow in a small diameter tube

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Coeficiente de operación de un sistema formado por un refrigerador doméstico acoplado a un acumulador de agua caliente para la recuperación de energía

An experimental apparatus containing a domestic refrigerator coupled to a vertical hot water storage tank was used for energy recovery. The original condenser of the refrigerator was maintained, but modified with a concentric tubes heat exchanger with countercurrent water and refrigerating gas flows. The coefficient of performance for the heat pump is calculated by the ratio of energy in the heat storage and the electric power consumed by the domestic refrigerator compressor. The results show that the increasing of hydrostatic pressure in the storage tank increases the water flow rate and the coefficient of performance. The proposed device also reduces the heat dissipation to the surroundings. This is more important in small confinements found in low-cost houses.

Quality control of Cotesia flavipes (Cameron) (Hymenoptera: Braconidae) from different Brazilian bio-factories

The goal of this study was to evaluate the quality of Cotesia flavipes from different bio-factories as biological control agents. We evaluated biological characteristics of the parasitoids throughout their lifespan, and measured the body length and width, abdomen width, thorax width and width and length of the right forewing of female and male parasitoids. Our results showed that the number of males and pupal viability were similar among the bio-factories; the number of emerged females was greater in bio-factories I and II; the egg-pupa period and the pupal period were shorter in bio-factory IV; and a greater longevity was found in bio-factories II and III. Sex ratio (at approximately 60% females) was satisfactory (in terms of suitability for release) across all bio-factories. For morphometric measurements, the body, abdomen and wing widths were similar in males; however, thorax width was greater in the males from bio-factory I; bio-factory III produced females with the highest body length; bio-factory I produced females with the greatest abdomen width; bio-factories III and IV produced females with the greatest wing length. Among the bio-factories studied, bio-factory IV produced the best quality C. flavipes, with respect to the greatest number of parasitoids per pupal mass (a mean of 57% more parasitoids) in a satisfactory sex ratio, and with the shortest developmental time, which facilitates faster rearing in the laboratory. Studies such as this, which assess the quality of a mass-produced C. flavipes, are crucial for the continued use of this parasitoid in controlling Diatraea saccharalis in the field. © 2013 Copyright Taylor and Francis Group, LLC.

Levantamento de coeficientes de desempenho de armazenador térmico associado a refrigerador doméstico modificado

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Construção de um dispositivo de simulação do escoamento pulsátil em artérias

Pós-graduação em Engenharia Mecânica - FEIS

Controle semi-ativo de vibrações usando lógica nebulosa e fluido magnetoreológico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Controle térmico de componentes eletrônicos com tubos de calor

Pós-graduação em Engenharia Mecânica - FEG

Levantamento de coeficientes de desempenho de refrigeradores domésticos associados a armazenador térmico

Pós-graduação em Engenharia Mecânica - FEB

Experimental investigation of smouldering in biomass

The smouldering process of wood logs was studied experimentally in a laboratory facility and in prescribed forest bums. The main goal was to check the parameters that initiate and control the stability of the smouldering process. To do so, sample temperatures at five different locations and concentrations of CO, CO2 and O-2 were measured and discussed. By varying the temperature and air supply of the flow tunnel apparatus, different rates of smoulder propagation were identified. In prescribed bums, the main characteristics of the self-sustained smouldering combustion front in logs of different sizes and species are reported. The average smouldering speed in the field is about one order of magnitude lower than that reported for different materials in laboratory experiments. (C) 2002 Elsevier B.V. Ltd. All rights reserved.