Parameterized fast decoupled power flow methods for obtaining the maximum loading point of power systems. Part I. Mathematical modeling

The conventional Newton and fast decoupled power flow (FDPF) methods have been considered inadequate to obtain the maximum loading point of power systems due to ill-conditioning problems at and near this critical point. It is well known that the PV and Q-theta decoupling assumptions of the fast decoupled power flow formulation no longer hold in the vicinity of the critical point. Moreover, the Jacobian matrix of the Newton method becomes singular at this point. However, the maximum loading point can be efficiently computed through parameterization techniques of continuation methods. In this paper it is shown that by using either theta or V as a parameter, the new fast decoupled power flow versions (XB and BX) become adequate for the computation of the maximum loading point only with a few small modifications. The possible use of reactive power injection in a selected PV bus (Q(PV)) as continuation parameter (mu) for the computation of the maximum loading point is also shown. A trivial secant predictor, the modified zero-order polynomial which uses the current solution and a fixed increment in the parameter (V, theta, or mu) as an estimate for the next solution, is used in predictor step. These new versions are compared to each other with the purpose of pointing out their features, as well as the influence of reactive power and transformer tap limits. The results obtained with the new approach for the IEEE test systems (14, 30, 57 and 118 buses) are presented and discussed in the companion paper. The results show that the characteristics of the conventional method are enhanced and the region of convergence around the singular solution is enlarged. In addition, it is shown that parameters can be switched during the tracing process in order to efficiently determine all the PV curve points with few iterations. (C) 2003 Elsevier B.V. All rights reserved.

Parameterized fast decoupled power flow methods for obtaining the maximum loading point of power systems. Part II. Performance evaluation

The parameterized fast decoupled power flow (PFDPF), versions XB and BX, using either theta or V as a parameter have been proposed by the authors in Part I of this paper. The use of reactive power injection of a selected PVbus (Q(PV)) as the continuation parameter for the computation of the maximum loading point (MLP) was also investigated. In this paper, the proposed versions obtained only with small modifications of the conventional one are used for the computation of the MLP of IEEE test systems (14, 30, 57 and 118 buses). These new versions are compared to each other with the purpose of pointing out their features, as well as the influence of reactive power and transformer tap limits. The results obtained with the new approaches are presented and discussed. The results show that the characteristics of the conventional FDPF method are enhanced and the region of convergence around the singular solution is enlarged. In addition, it is shown that these versions can be switched during the tracing process in order to efficiently determine all the PV curve points with few iterations. A trivial secant predictor, the modified zero-order polynomial, which uses the current solution and a fixed increment in the parameter (V, theta, or mu) as an estimate for the next solution, is used for the predictor step. (C) 2003 Elsevier B.V. All rights reserved.

Influence of Fluid Concentration on the Elevation of Boiling Point of Blackberry Juice

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Strangeness data with light projectiles from a hydrodynamical point of view

The usual particle emission scenario used in hydrodynamics presupposes that particles instantaneously stop interacting (freeze-out) once they reach some three-dimensional surface. Another formalism has recently been developed where particle emission occurs continuously during the whole expansion of thermalized matter. Here we compare both mechanisms in a simplified hydrodynamical framework and show that they lead to a drastically different interpretation of data.

Strangeness data with heavy projectiles from a hydrodynamical point of view

We compare the results obtained by using the continuous emission model with data from Ph-Ph collisions. We determine the initial conditions necessary to reproduce the strange particle ratios (experiment WA97) and with the obtained results, we study the dependence on particle mass of the inverse slope parameter T. Some particle spectra are also shown.

Initial Development of Bovine Placentation (Bos indicus) from the Point of View of the Allantois and Amnion

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Solid mass falling into the reservoirs shallow water equations validity from the engineering point of view

Water waves generated by a solid mass is a complex phenomenon discussed in this paper by numerical and experimental approaches. A model based on shallow water equations with shocks (Saint Venant) has developed. It can reproduce the amplitude and the energy of the wave quite well, but because it consistently generates a hydraulic jump, it is able to reproduce the profile, in the case of high relative thickness of slide, but in the case of small relative thickness it is unable to reproduce the amplitude of the wave. As the momentum conservation is not verified during the phase of wave creation, a second technique based on discharge transfer coefficient α, is introduced at the zone of impact. Numerical tests have been performed and validated this technique from the experimental results of the wave's height obtained in a flume.

Elevation of boiling point of coffee extract

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermal evaporation: Representation of rise in boiling point of grapefruit juice

The rise in boiling point of grapefruit juice was experimentally measured at soluble solids concentrations in the range of 9.3-60.6 °Brix and pressures between °6.0 × 103 and 9.0 × 104 Pa. Different approaches to represent experimental data, including the Dhring's rule, the Antoine equation and empirical models proposed in the literature were tested. In the range of 9.3-29.0 °Brix, the rise in boiling point was nearly independent of pressure, varying only with juice concentration. Considerable deviations of this behavior began to occur at concentrations higher than 29.0 °Brix. Experimental data could be best predicted by adjusting an empirical model, which consisted of a single equation that takes into account the dependence of rise in boiling point on pressure and concentration. © SAGE Publications 2007.

Peirce's mathematical-logical approach to discrete collections and the premonition of continuity

According to Peirce one of the most important philosophical problems is continuity. Consequently, he set forth an innovative and peculiar approach in order to elucidate at once its mathematical and metaphysical challenges through proper non-classical logical reasoning. I will restrain my argument to the definition of the different types of discrete collections according to Peirce, with a special regard to the phenomenon called premonition of continuity (Peirce, 1976, Vol. 3, p. 87, c. 1897). © 2012 Copyright Taylor and Francis Group, LLC.

A note about splittings of groups and commensurability under a cohomological point of view

Let G be a group, let S be a subgroup with infinite index in G and let FSG be a certain Z2G-module. In this paper, using the cohomological invariant E(G, S, FSG) or simply E˜(G, S) (defined in [2]), we analyze some results about splittings of group G over a commensurable with S subgroup which are related with the algebraic obstruction “singG(S)" defined by Kropholler and Roller ([8]. We conclude that E˜(G, S) can substitute the obstruction “singG(S)" in more general way. We also analyze splittings of groups in the case, when G and S satisfy certain duality conditions.

Is the internal connection more efficient than external connection in mechanical, biological, and esthetical point of views? A systematic review

This systematic review aimed to evaluate if the internal connection is more efficient than the external connection and its associated influencing factors. A specific question was formulated according to the Population, Intervention, Control, and Outcome (PICO): Is internal connection more efficient than external connection in mechanical, biological, and esthetical point of views? An electronic search of the MEDLINE and the Web of Knowledge databases was performed for relevant studies published in English up to November 2013 by two independent reviewers. The keywords used in the search included a combination of dental implant and internal connection or Morse connection or external connection. Selected studies were randomized clinical trials, prospective or retrospective studies, and in vitro studies with a clear aim of investigating the internal and/or external implant connection use. From an initial screening yield of 674 articles, 64 potentially relevant articles were selected after an evaluation of their titles and abstracts. Full texts of these articles were obtained with 29 articles fulfilling the inclusion criteria. Morse taper connection has the best sealing ability. Concerning crestal bone loss, internal connections presented better results than external connections. The limitation of the present study was the absence of randomized clinical trials that investigated if the internal connection was more efficient than the external connection. The external and internal connections have different mechanical, biological, and esthetical characteristics. Besides all systems that show proper success rates and effectiveness, crestal bone level maintenance is more important around internal connections than external connections. The Morse taper connection seems to be more efficient concerning biological aspects, allowing lower bacterial leakage and bone loss in single implants, including aesthetic regions. Additionally, this connection type can be successfully indicated for fixed partial prostheses and overdenture planning, since it exhibits high mechanical stability.

Vacuum energy and the fixed point of QED

The vacuum energy of QED, as a function of the coupling constant α, is shown to have an absolute minimum at the critical coupling αc=π/3. The effect of chiral symmetry breaking diminishes as the coupling is increased. We argue that these aspects of the vacuum energy shall remain unaltered beyond the ladder approximation.

Women from the point of view of the Bukowskian narrator: the representation of the feminine universe in Erections, Ejaculations, Exhibitions and General Tales of Ordinary Madness

Pós-graduação em Letras - IBILCE