Observation of piezoelectric response on tungsten doped barium zirconium titanate ceramics

This study describes observation of piezoelectric response of Ba(Zr 0.10Ti 0.90.O3 ceramics modified with tungsten (BZT:2W) by the mixed oxide method. According to X ray diffraction analysis, the ceramics are free of secondary phases. Transmission electron microscopy (TEM) analyses reveals the absence of segregates in the grain boundaries indicates the high solubility of WO3 in the BZT matrix. The dielectric permittivity measured at a frequency of 10 KHz was equal to 6500 with dieletric loss of 0.15. A typical hysteresis loop was observed at room temperature. Electron Paramagnetic Resonance (EPR) analyses reveals that substitution of W6+ by Ti4+ causes distortion in the crystal structure changing lattice parameter. Polarization reversal was investigated by applying dc voltage through a conductive tip during the area scanning. Piezoelectric force microscopy images reveals that in-plane response may not change its sign upon polarization switching, while the out-of-plane response does. Copyright © 2010 American Scientific Publishers.

Hybridization effects on the out-of-plane electron tunneling properties of monolayers: is h-BN more conductive than graphene?

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of microwave energy on structural and piezoelectric response of Bi 4Ti 3O 12 ceramics

Bismuth titanate ceramics (Bi 4Ti 3O 12) with 10 wt% in excess of bismuth (BIT10) were prepared by the polymeric precursor method and sinterized in microwave (MW) and conventional furnaces (CF). The effect of microwave energy on structural and electrical behavior of BIT10 ceramics was investigated by means of X-ray diffraction (XRD), Scanning electron microscopy (SEM) and electrical measurements. The results of the BIT10 ceramics processed in the microwave furnace (MW) showed a high structural organization compared to conventional treatment (CF). Size of grains and dieletrical properties are influenced by annealing conditions while coercitive field is not dependent on it. The maximum dielectric permittivity (12000) was obtained for the sample sintered in the microwave furnace. Piezoelectric force microscopy images reveals that in-plane response may not change its sign upon polarization switching, while the out-of-plane response does with the influence of microwave energy. Copyright © 2010 American Scientific Publishers All rights reserved.

Dynamic stationary response of reinforced plates by the boundary element method

A direct version of the boundary element method (BEM) is developed to model the stationary dynamic response of reinforced plate structures, such as reinforced panels in buildings, automobiles, and airplanes. The dynamic stationary fundamental solutions of thin plates and plane stress state are used to transform the governing partial differential equations into boundary integral equations (BIEs). Two sets of uncoupled BIEs are formulated, respectively, for the in-plane state ( membrane) and for the out-of-plane state ( bending). These uncoupled systems are joined to formamacro-element, in which membrane and bending effects are present. The association of these macro-elements is able to simulate thin-walled structures, including reinforced plate structures. In the present formulation, the BIE is discretized by continuous and/or discontinuous linear elements. Four displacement integral equations are written for every boundary node. Modal data, that is, natural frequencies and the corresponding mode shapes of reinforced plates, are obtained from information contained in the frequency response functions (FRFs). A specific example is presented to illustrate the versatility of the proposed methodology. Different configurations of the reinforcements are used to simulate simply supported and clamped boundary conditions for the plate structures. The procedure is validated by comparison with results determined by the finite element method (FEM).

Application of rotor response analysis to fault detection in hydro powerplants.

In this article some considerations obtained during the utilization of rotor response analysis techniques in hydraulic powerplants are discussed. An applied research work was carried out in two hydraulic turbines analysing the rotor response both theoretically and experimentally. A developed mathematical model was used to simulate the rotordynamic behaviour of Francis and Kaplan turbines. The main dynamical effects that appear during the operation of the machines are discussed too. A series of measurements were carried out in the turbines using impact hammers to determine the modal behaviour of the units. The tests were carried out with the machine still and in operation. Some results and the comparison with the theory is presented in this article. The improved theoretical model was used for a sensitivity analysis of the different bearings to the main excitations that fake place during the machine operation. From this analysis, the best measuring points for condition monitoring were determined.

Effect of intensification on grow out of the Amazon River prawn, Macrobrachium amazonicum

The effects of intensification on growth, survival, productivity, population structure, and distribution of harvested biomass in individual size classes of Macrobrachium amazonicum in semi-intensive culture were evaluated. Postlarvae (0.01 g) were stocked in 12 ponds at densities of 10, 20, 40, and 80/m(2) (three replicates per treatment) and raised for 5.5 mo. Average individual weight significantly decreased and productivity significantly increased as stocking density increased (P < 0.001), while survival was not affected (P > 0.05). Prawn mean weight at harvest ranged from 3.6 (80/m(2)) to 7.0 g (10/m(2)). Average survival ranged from 65.5% (40/m(2)) to 72.8% (20/m(2)), while productivity ranged from 508 (10/m(2)) to 2051 kg/ha (80/m(2)). Harvested biomass showed a clear bimodal distribution in individual size classes indicating the occurrence of heterogeneous growth, which may affect management and market strategies. Harvested biomass of prawns weighing more than 7 g (the best market size) increases for stocking densities up to 40/m(2) and stabilizes between 40 and 80/m(2). Growth reduction was associated with a decreasing frequency and average weight of green claw 1 and green claw 2 male morphotypes and adult females as density increased. Thus, the distribution of male morphotypes and sexually mature females are affected by density-dependent factors. Results suggest that prawn density plays an important role on M. amazonicum grow-out phase, as has been demonstrated for other species of the genus Macrobrachium. M. amazonicum tolerates grow-out intensification and may be raised in both semi-intensive and intensive systems stocked at very high densities yielding high productivity.

Adenosine deaminase activity as a biochemical marker of inflammatory response in goats infected by caprine arthritis-encephalitis virus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of stitched fabric composite processed by RTM in quasi-static test

Stitched fabrics have been widely studied for potential application in aircraft structures since stitch yarns offer improvements in the out-of-plane mechanical properties and also can save time in the lay up process. The down side of stitch yarns came up in the manufacturing process of fabric in which defects introduced by the needle movement creating fiber-free-zones, fiber breakage and misalignment of fibers. The dry stitched carbon fabric preform has mainly been used in the Resin Transfer Molding (RTM) process which high fiber content is aimed, those defects influence negatively the injection behavior reducing the mechanical properties of final material. The purpose of this research work focused on testing in quasi-static mechanical mode (in-plane tension) of a monocomponent resin CYCOM (R) 890 RTM/carbon fiber anti-symmetric quadriaxial fabric stitched by PE 80Dtex yarn processed by RTM. The evaluation consisted in comparing the scatter of the quasi-static test with the attenuation of ultrasonic maps, which show the path of the resin and possible dry spots considering that interference of yarn in resin flow is detectable in ultrasonic measurement. Microscopic analysis was also considered for further evaluation in case of premature failure. (C) 2011 Published by Elsevier Ltd. Selection and peer-review under responsibility of ICM11

Design of concrete platforms offshore using the three-layer shell theory

The concrete offshore platforms, which are subjected a several loading combinations and, thus, requires an analysis more generic possible, can be designed using the concepts adopted to shell elements, but the resistance must be verify in particular cross-sections to shear forces. This work about design of shell elements will be make using the three-layer shell theory. The elements are subject to combined loading of membrane and plate, totalizing eight components of internal forces, which are three membrane forces, three moments (two out-of-plane bending moments and one in-plane, or torsion, moment) and two shear forces. The design method adopted, utilizing the iterative process proposed by Lourenco & Figueiras (1993) obtained from equations of equilibrium developed by Gupta (1896) , will be compared to results of experimentally tested shell elements found in the literature using the program DIANA.

Features of dielectric response in PMN-PT ferroelectric ceramics

In this paper, electrical and structural properties were reported for pyrochlore free (1-x)[Pb(Mg1/3Nb2/3)O-3] - xPbTiO(3) (PMN-PT) (with 35 mol% PbTiO3) ceramics obtained from fine powders. Dielectric studies were focused on the investigation of the complex dielectric permittivity (epsilon '-i epsilon '') as a function of frequency and temperature. The effects of the dc applied electric field on dielectric response were also investigated. Results revealed a field dependence dielectric anomaly in the dielectric permittivity curves (epsilon(T)) in the low dc electric field region, which in turn prevails in the whole analysed frequency interval. To the best of our knowledge, these properties for the PMN-PT ceramic system have not been reported before as in this work. The results were analysed within the framework of the current models found in the literature.

Peritonitis in recent years: clinical findings and predictors of treatment response of 170 episodes at a single Brazilian center

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of tissue response to periodontal dressings: Histological study in tooth sockets of rats

Although the use of periodontal dressings is currently limited, there are some indications for their use. Selection of any material that will have direct contact with live tissues, such as periodontal dressings, should be careful in order to allow surgical wound healing. The aim of this study was to evaluate the intensity of inflammatory response and bone formation in tooth sockets of rats after implantation of three periodontal dressings. After removal of the right maxillary incisors of 84 male rats, each tooth socket received implantation of a polyethylene tube, 63 of which were filled with non-eugenol periodontal dressing and the remaining 21 tubes remained empty (control group). Histological evaluation assessed the intensity of inflammatory response and presence and location of bone tissue formation at postoperative periods of 7, 14 and 28 days. Statistical analysis was performed by the Kruskal-Wallis test at 5% significance level. Regarding the inflammatory infiltrate, at 28 days, there was statistically significant difference between one of periodontal dressings and control group (p < 0.05). Analysis of postoperative periods, showed that the control group presented statistically significant reduction in the inflammatory infiltrate comparing the 14- and 28-day periods (p < 0.05). Regarding bone tissue formation, there was difference in control group between the 7- and 28-day periods (p < 0.05). Within the experimental conditions, it may be concluded that no differences were found in the inflammatory response among the groups at 7 and 14 days and that Voco pac (TM) dressing induced a more intensive inflammatory reaction at 28 days.

Nanoscale electromechanical properties of CaCu3Ti4O12 ceramics

Piezoresponse Force Microscopy (PFM) is used to characterize the nanoscale electromechanical properties of centrosymmetric CaCu3Ti4O12 ceramics with giant dielectric constant. Clear PFM contrast both in vertical (out-of-plane) and lateral (in-plane) modes is observed on the ceramic surface with varying magnitude and polarization direction depending on the grain crystalline orientation. Lateral signal changes its sign upon 180 degrees rotation of the sample thus ruling out spurious electrostatic contribution and confirming piezoelectric nature of the effect. Piezoresponse could be locally reversed by suitable electrical bias (local poling) and induced polarization was quite stable showing long-time relaxation (similar to 3 hrs). The electromechanical contrast in unpoled ceramics is attributed to the surface flexoelectric effect (strain gradient induced polarization) while piezoresponse hysteresis and ferroelectric-like behavior are discussed in terms of structural instabilities due to Ti off-center displacements and structural defects in this material. (C) 2011 American Institute of Physics. [doi:10.1063/1.3623767]

Soft chemical deposition of BiFeO3 multiferroic thin films

BiFeO3 thin films free of secondary phases were obtained by the soft chemical solution on Pt(111)/Ti/SiO2/Si substrates after annealing at 500 degrees C for 2 h. The film grown in the (100) direction presented a remanent polarization P-r of 31 mu C/cm(2) at room temperature. Electrical measurements using both quasistatic hysteresis and pulsed polarization confirm the existence of ferroelectricity with a switched polarization of 60-70 mu C/cm(2), Delta P=(P-*-P). Low leakage conduction and an out-of-plane piezoelectric (d(3)) coefficient of 40 pm/V were obtained by the improvement of preparation technology.