Numerical analysis of refrigerant flow along non-adiabatic capillary tubes using a two-fluid model

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

PHYLOGENETIC STUDIES OF SOME SPECIES OF THE GENUS COFFEA .1. NUMERICAL-ANALYSIS OF FLAVONOID COMPOUNDS

Flavonoid compounds were analyzed in ripe fruit pulp of ten species of Coffea, including two cultivars of C. arabica and two of C. canephora. Three coefficients of similarity: Simple-Matching, Jaccard and Ochiai and three different clustering methods, Single Linkage, Complete Linkage and Unweighted Pair Group, Using Arithmetic Averages (UPGMA), were used to analyze the data.Jaccard and Ochiai's coefficients of association showed a more coherent result, when compared with taxonomic and hybridization studies. Inclusion of Psilanthopsis kapakata in the genus Coffea, as C. kapakata, is justified by the similarity of this species with other studied species, and clusters clearly approximate the species C. arabica and C. eugenioides. The latter is one of the possible parents of the allotetraploid species C. arabica, C. congensis is the only species whose position remains ambiguous, probably due to the fact that the plants of this species that were introduced into the Campinas collections, were hybrids and not typical of C. congensis.

PHYLOGENETIC STUDIES OF SOME SPECIES OF THE GENUS COFFEA .2. NUMERICAL-ANALYSIS OF ISOENZYMATIC DATA

Thirteen species of Coffea were studied for five enzymes systems, including alpha and beta esterase, alkaline phosphatase, acid phosphatase, malate dehydrogenase and acid dehydrogenase. Three coefficients of similarity: Simple Matching, Jaccard and Ochiai and three different clustering methods: Single Linkage, Complete Linkage and Unweighted Pair Group, using Arithmetic Averages (UPGMA) were used to analyse the data.The phylogenetic relationships among the twelve diploid species and between them and the tetraploid species C. arabica showed that similarity among species of the same subsection is not always greater than among species of different subsections. In addition, although there are several similarity groups in common, established by isoenzymatic polymorphism, morphological characteristics, chemical data, crossability and geographic distribution, there is no common trend among the phylogenetic relationships as indicated by all these different evaluating procedures.

Numerical analysis of a modified evacuated tubes solar collector

The need for renewable energy sources, facing the consequences of Climate Change, results in growing investment for solar collectors’ use. Research in this field has accompanied this expansion and evacuated tube solar collector stands as an important study focus. Thus, several works have been published for representing the stratification of the fluid inside the tubes and the reservoir, as well as analytical modeling for the heat flow problem. Based on recent publications, this paper proposes the study of solar water heating with evacuated tubes, their operation characteristics and operating parameters. To develop this work, a computational tool will be used - in this case, the application of computational fluid dynamics (CFD) software. In possession of the implemented model, a numerical simulation will be performed to evaluate the behavior of the fluid within this solar collector and possible improvements to be applied in the model.

NUMERICAL SIMULATION of THE BEHAVIOR of THE BEHAVIOR of REINFORCED CONCRETE BEAMS and COLUMNS BY FEM CAASTEM 2000 PROGRAM

The objective of this paper is the numerical study of the behavior of reinforced concrete beams and columns by non-linear numerical simulations. The numerical analysis is based on the finite element method implemented in CASTEM 2000. This program uses the constitutive elastoplastic perfect model for the steel, the Drucker-Prager model for the concrete and the Newton-Raphson for the solution of non-linear systems. This work concentrates on the determination of equilibrium curves to the beams and force-strain curves to the columns. The numeric responses are confronted with experimental results found in the literature in order to check there liability of the numerical analyses.

Numerical approximation of the Ginzburg-Landau equation with memory effects in the dynamics of phase transitions

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Numerical modeling of flow through an industrial burner orifice

This paper presents numerical modeling of a turbulent natural gas flow through a non-premixed industrial burner of a slab reheating furnace. The furnace is equipped with diffusion side swirl burners capable of utilizing natural gas or coke oven gas alternatively through the same nozzles. The study is focused on one of the burners of the preheating zone. Computational Fluid Dynamics simulation has been used to predict the burner orifice turbulent flow. Flow rate and pressure at burner upstream were validated by experimental measurements. The outcomes of the numerical modeling are analyzed for the different turbulence models in terms of pressure drop, velocity profiles, and orifice discharge coefficient. The standard, RNG, and Realizable k-epsilon models and Reynolds Stress Model (RSM) have been used. The main purpose of the numerical investigation is to determine the turbulence model that more consistently reproduces the experimental results of the flow through an industrial non-premixed burner orifice. The comparisons between simulations indicate that all the models tested satisfactorily and represent the experimental conditions. However, the Realizable k-epsilon model seems to be the most appropriate turbulence model, since it provides results that are quite similar to the RSM and RNG k-epsilon models, requiring only slightly more computational power than the standard k-epsilon model. (C) 2014 Elsevier Ltd. All rights reserved.

A Numerical Study of the FENE-CR Model Applied to a Jet Flow Problem

The FENE-CR model is investigated through a numerical algorithm to simulate the time-dependent moving free surface flow produced by a jet impinging on a flat surface. The objective is to demonstrate that by increasing the extensibility parameter L, the numerical solutions converge to the solutions obtained with the Oldroyd-B model. The governing equations are solved by an established free surface flow solver based on the finite difference and marker-and-cell methods. Numerical predictions of the extensional viscosity obtained with several values of the parameter L are presented. The results show that if the extensibility parameter L is sufficiently large then the extensional viscosities obtained with the FENE-CR model approximate the corresponding Oldroyd-B viscosity. Moreover, the flow from a jet impinging on a flat surface is simulated with various values of the extensibility parameter L and the fluid flow visualizations display convergence to the Oldroyd-B jet flow results.

Short Implant to Support Maxillary Restorations: Bone Stress Analysis Using Regular and Switching Platform

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Regular and Platform Switching: Bone Stress Analysis Varying Implant Type

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of high insertion torque on implant placement - an anisotropic bone stress analysis

The aim of this study was to evaluate the influence of the high values of insertion torques on the stress and strain distribution in cortical and cancellous bones. Based on tomography imaging, a representative mathematical model of a partial maxilla was built using Mimics 11.11 and Solid Works 2010 softwares. Six models were built and each of them received an implant with one of the following insertion torques: 30, 40, 50, 60, 70 or 80 Ncm on the external hexagon. The cortical and cancellous bones were considered anisotropic. The bone/implant interface was considered perfectly bonded. The numerical analysis was carried out using Ansys Workbench 10.0. The convergence of analysis (6%) drove the mesh refinement. Maximum principal stress (σ max) and maximum principal strain (ε max) were obtained for cortical and cancellous bones around to implant. Pearson's correlation test was used to determine the correlation between insertion torque and stress concentration in the periimplant bone tissue, considering the significance level at 5%. The increase in the insertion torque generated an increase in the σ max and ε max values for cortical and cancellous bone. The σmax was smaller for the cancellous bone, with greater stress variation among the insertion torques. The ε max was higher in the cancellous bone in comparison to the cortical bone. According to the methodology used and the limits of this study, it can be concluded that higher insertion torques increased tensile and compressive stress concentrations in the periimplant bone tissue.

Mecanismos de movimentação animal embasados na memória espacial

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of Platform and Abutment Angulation on Peri-Implant Bone. A Three-Dimensional Finite Element Stress Analysis

The aim of this study was to evaluate stress distribution on the pen-implant bone, simulating the influence of Nobel Select implants with straight or angulated abutments on regular and switching platform in the anterior maxilla, by means of 3-dimensional finite element analysis. Four mathematical models of a central incisor supported by external hexagon implant (13 mm x 5 mm) were created varying the platform (R, regular or S. switching) and the abutments (S, straight or A, angulated 15 degrees). The models were created by using Mimics 13 and Solid Works 2010 software programs. The numerical analysis was performed using ANSYS Workbench 10.0. Oblique forces (100 N) were applied to the palatine surface of the central incisor. The bone/implant interface was considered perfectly integrated. Maximum (sigma(max)) and minimum (sigma(min)) principal stress values were obtained. For the cortical bone the highest stress values (sigma(max)) were observed in the RA (regular platform and angulated abutment, 51 MPa), followed by SA (platform switching and angulated abutment, 44.8 MPa), RS (regular platform and straight abutment, 38.6 MPa) and SS (platform switching and straight abutment, 36.5 MPa). For the trabecular bone, the highest stress values (sigma(max)) were observed in the RA (6.55 MPa), followed by RS (5.88 MPa), SA (5.60 MPa), and SS (4.82 MPa). The regular platform generated higher stress in the cervical periimplant region on the cortical and trabecular bone than the platform switching, irrespective of the abutment used (straight or angulated).

Stress distribution on dentin-cement-post interface varying root canal and glass fiber post diameters. A three-dimensional finite element analysis based on micro-C data

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)