Optimization of a novel nitric oxide sensor using a latex rubber matrix

This study present a novel NO sensor made of a spin trap (iron(II)-diethyldithiocarbamate complex, FeDETC) incorporated in a latex rubber matrix and works as a trap for NO, which is detectable by Electron Paramagnetic Resonance (EPR). We explored the optimization of our sensors changing systematically two fabrication parameters: the latex rubber matrix temperature of polymerization and FeDETC concentration inside the matrix. The sensor was prepared in four different temperatures: 4, 10, 20 and 40°C. The FeDETC concentration was also varied from 0.975 to 14.8 mM. We observed a variation of the EPR signals from the sensors prepared at different conditions. We found a high stability of the EPR response from our sensor, 40 days at RT. The best sensor was made with a latex rubber matrix polymerized at 10°C and with a FeDETC concentration of 14.8 mM. In vivo tests show good biocompatibility of our sensor. © 2007 Asian Network for Scientific Information.

Nitric oxide release using natural rubber latex as matrix

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Metronidazole release using natural rubber latex as matrix

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preparation and structural characterization of vulcanized natural rubber nanocomposites containing nickel-zinc ferrite nanopowders

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Age-age correlation for early selection of rubber tree genotypes in São Paulo State, Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Obtenção e caracterização de compósitos de borracha natural e polianilina com ferrita de bário

Pós-graduação em Ciência dos Materiais - FEIS

Morphological characterization by SEM, TEM and AFM of nanoparticles and functional nanocomposites based on natural rubber filled with oxide nanopowders

Nanocomposites were prepared from mixture of different concentrations of ferroelectric nanoparticles in an elastomeric matrix based on the vulcanized natural rubber. The morphological characterization of nanocomposites was carried out using Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and Atomic force microscopy (AFM). The nanocrystalline ferroelectric oxide is potassium strontium niobate (KSN) with stoichiometry KSr2Nb5O15, and was synthesized by the chemical route using a modified polyol method, obtaining particle size and microstrain equal to 20 nm and 0.32, respectively. These ferroelectric nanoparticles were added into the natural rubber in concentrations equal to 1, 3, 5, 10, 20 and 50 phr (parts per hundred of rubber) forming ferroelectric nanocomposites (NR/KSN). Using morphological characterization, we identified the maximum value of surface roughness at low concentrations, in particular, sample with 3 phr of nanoparticles and factors such as encapsulation and uniformity in the distribution of nanoparticles into the natural rubber matrix are investigated and discussed.

Estudo comparativo do desempenho de diferentes membranas oclusivas de Látex Natural no reparo ósseo

Introduction: In dentistry, alveolar bone resorption is a limiting factor in the well being of individuals directly interfering in the stomatognathic system, causing problems in the context of overall health. Aiming to promote biological methods that can stimulate bone regeneration, several biomimetic strategies have been developed by the use of diverse materials possible to the bone matrix, culminating in the development of techniques that promote such repair. Objective: This work is a comparative study of the performance of films made with latex as occlusive membrane for Guided Bone Regeneration (GBR) procedure in three preparations: Latex preserved in ammonia, produced by Latex rubber clones IAN873 and PR255 polymerized immediately after collection and without use ammonia as a preservative. Methods: Sixty Wistar rats were randomly divided into 4 groups of 15 animals in which bone defects of critical size (8mm diameter) were made surgically in the skull. Group A was treated by GBR through the membrane latex preserved with ammonia, Group B received the membrane made of latex from IAN873, Group C, the membrane clone PR255 and group D was not treated by GBR. After a period of 7, 15 and 50 days, 5 animals from each group were euthanized, and specimens containing bone defect collected for microscopic examination (descriptive histology and histomorphometry). Results: The results showed that after 50 days there was bone formation in higher proportions in group D (p <0.05, ANOVA followed by Tukey), suggesting that further experiments should be conducted to conclude about the presence of ammonia and the influence of kind of rubber. Conclusion: GOR is a procedure proven effective in the treatment of bone defects. Therefore, further experiments should be conducted to reach a conclusion regarding the presence of ammonia in the latex composition for the manufacture of membranes, as well as the difference induced by the species of rubber.

Estudo da influência de tratamentos químicos da fibra de sisal nas propriedades de compósitos com borracha nitrílica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sistemas de liberação controlada de óxido nítrico baseados em ditiocarbamatos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação das propriedades físicas e químicas da madeira de Hevea brasiliensis em relação ao painel de extração de látex

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da qualidade das lâminas no desempenho físico-mecânico de painéis compensados de Hevea brasiliensis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação das propriedades físico-mecânicas da madeira de árvores de Hevea Brasiliensis em três condições de sanidade no Estado de São Paulo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudos sistemáticos de biocompatibilidade e potencial osteogênico de membranas bioativas em coelhos machos

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Evaluation of thermal behavior of latex membranes from genetically improved rubber tree (Hevea brasiliensis)

Thermal stability, thermal decomposition process, residual mass, temperature of glass transition (T-g) and temperature dependence of storage modulus (E'), were determined for latex membranes prepared from six clones of Hevea brasiliensis: IAC 331, IAC 332, IAC 333 and IAC 334 grown at experimental plantations of Instituto Agronomico de Campinas (IAC) in Votuporanga, São Paulo State, Brazil. Latex membranes from GT1 and RRIM 600 Asian matrix clones were used as references. The thermal behavior of latex membranes from genetically improved rubber trees was characterized using thermogravimetry/derivative thermogravimetry (TG/DTG), differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The thermal behavior of latex from clones studied in the present work showed similar features of the clones previously reported (IAC 40, IAC 300, IAC 301, IAC 328, IAC 329 and IAC 330), with mass loss in four consecutive steps, except IAC 333, which showed an additional mass loss step. (c) 2006 Elsevier B.V. All rights reserved.