Sintering of zirconia composites obtained by slip casting

Composites containing a matrix of nanometric Ce-stabilized zirconia with an addition of micrometric monoclinic zirconia were processed by slip casting and sintered at a relatively low temperature. The ratio between nanometric and micrometric particles was determined according to the viscosity of the suspensions and the final density of the pellets. An optimum amount of micrometric particles was necessary to achieve improved suspension dispersion and higher pellet density. The amount of deflocculant in the suspensions containing the mixture of micrometric and nanometric particles was optimized by viscosity measurements. The pellets were characterized by dilatometry, Hg porosimetry, density measurement (the Archimedes method) and scanning electron microscopy. Despite the low green density obtained (35-38% of the theoretical density), densities as high as 97.5% were achieved after sintering. (C) 2001 Elsevier B.V. Ltd and Techna S.r.l. All rights reserved.

Preparation of 9.5/65/35 PLZT powders by organic precursor method

In this study the preparation of 9.5/65/35 PLZT ceramic powders were investigated. The powders with the formula Pb0.905La0.095(Zr0.65 Ti0.35)0.976O3 + 3.5 w% PbO were prepared using Pechini process and partial oxalate method. The powder phase formation, powder morphology, and green density of PLZT were shown.

α-SiAION: Development and machining test on gray cast iron

The α-SiAlON ceramic cutting tool insert is developed. Silicon nitride and additives powders are pressed and sintered in the form of cutting tool inserts at temperature of 1900 °C. The physics and mechanical properties of the inserts like green density, weight loss, relative density, hardness and fracture toughness are evaluated. Machining studies are conducted on grey cast iron workpiece to evaluate the performance of α-SiAlON ceramic cutting tool. In the paper the cutting tool used in higher speed showed an improvement in the tribological interaction between the cutting tools and the grey cast iron workpiece resulted in a significant reduction of flank wear and roughness, because of better accommodation and the presence of the graphite in gray cast iron. The above results are discussed in terms of their affect at machining parameters on gray cast iron.

Use of high energy ball milling on the sintering optimization of alumina ceramics

In this work, the effect of the milling time on the densification of the alumina ceramics with or without 5wt.%Y 2O 3, is evaluated, using high-energy ball milling. The milling was performed with different times of 0, 2, 5 or 10 hours. All powders, milled at different times, were characterized by X-Ray Diffraction presenting a reduction of the crystalline degree and crystallite size as function of the milling time increasing. The powders were compacted by cold uniaxial pressing and sintered at 1550°C-60min. Green density of the compacts presented an increasing as function of the milling time and sintered samples presented evolution on the densification as function of the reduction of the crystallite size of the milled powders. © (2010) Trans Tech Publications.

Influência dos dopantes potássio e lítio na cerâmica relaxora niobato de chumbo e magnésio (PMN)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

GREEN MACHINING ORIENTED TO DIMINISH DENSITY GRADIENT FOR MINIMIZATION of DISTORTION IN ADVANCED CERAMICS

After sintering advanced ceramics, there are invariably distortions, caused in large part by the heterogeneous distribution of density gradients along the compacted piece. To correct distortions, machining is generally used to manufacture pieces within dimensional and geometric tolerances. Hence, narrow material removal limit conditions are applied, which minimize the generation of damage. Another alternative is machining the compacted piece before sintering, called the green ceramic stage, which allows machining without damage to mechanical strength. Since the greatest concentration of density gradients is located in the outer-most layers of the compacted piece, this study investigated the removal of different allowance values by means of green machining. The output variables are distortion after sintering, tool wear, cutting force, and the surface roughness of the green ceramics and the sintered ones. The following results have been noted: less distortion is verified in the sintered piece after 1mm allowance removal; and the higher the tool wear the worse the surface roughness of both green and sintered pieces.

Soil CO2 emission and its relation to soil properties in sugarcane areas under Slash-and-burn and Green harvest

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Different origins of green-light photoluminescence emission in structurally ordered and disordered powders of calcium molybdate

A strong greenish-light photoluminescence (PL) emission was measured at room temperature for disordered and ordered powders of CaMoO4 prepared by the polymeric precursor method. The structural evolution from disordered to ordered powders was accompanied by XRD. Raman spectroscopy, and TEM imagery. High-level quantum mechanical calculations in the density functional framework were used to interpret the formation of the structural defects of disorder powders in terms of band diagram and density of states. Complex cluster vacancies [MoO3 center dot V-O(z)] and [CaO7 center dot V-O(z)] (where V-O(z) = V-O(X), V-O(center dot), V-O(center dot center dot)) were suggested to be responsible to the appearance of new states shallow and deeply inserted in the band gap. These defects give rise to the PL in disordered powders. The natural PL emission of ordered CaMoO4 was attributed to an intrinsic slight distortion of the [MoO4] tetrahedral in the short range.

Recovery of soil physical properties by green manure, liming, gypsum and pasture and spontaneous native species

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

BRACHYURAN CRABS (DECAPODA, BRACHYURA) ASSOCIATED WITH THE GREEN SPONGE AMPHIMEDON VIRIDIS (DEMOSPONGIAE) FROM ITAGUA BEACH, SOUTH-EASTERN COAST of BRAZIL

This study provides information on the community structure of brachyuran crabs associated with the green sponge, Amphimedon viridis Duchassaing & Michelotti, 1864, from a beach on the south-eastern coast of Brazil. Monthly collections from May 2002 through August 2003 were carried out on the rocky bottoms off Itagua Beach (23 degrees 27'07 '' S 45 degrees 02'49 '' W). Crabs on the green sponge banks were hand-caught during snorkelling sessions, and 638 crabs belonging to 31 species, 19 genera, and 10 families were obtained. Biological parameters, including sponge volume, number of individuals, density, richness, diversity, evenness, and dominance changed considerably over time. Species recruitment and foraging habit are some of the factors that drive the richness, dominance, and diversity patterns of this community. The green sponge banks are important sites for recruitment, refuge, and feeding of many species of brachyurans. Therefore, they are also important for the conservation of this group on the south-eastern coast of Brazil.

Comparison of the photodynamic fungicidal efficacy of methylene blue, toluidine blue, malachite green and low-power laser irradiation alone against Candida albicans

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Measurement of the Pseudorapidity and Centrality Dependence of the Transverse Energy Density in Pb-Pb Collisions at root s(NN)=2.76 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A simple and green analytical method for determination of glyphosate in commercial formulations and water by diffuse reflectance spectroscopy

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dry matter production of shoots and root density of two cultivars of Lablab purpureus (L.) Sweet

This experiment was conducted in green house conditions to evaluate the DM accumulation in the shoots and in the roots of two cultivars of Lablab purpureus (L.) Sweet. A 2x3 factorial (two cultivars and three evaluation dates) was conducted according to a randomized complete block design with four replications, being the cultivars Highworth and Rongai evaluated at 42, 56, and 70 days after seedling emergence (DASE). The results indicated that the cvs. Highworth and Rongai have the same pattern of DM accumulation in the shoots. In the upper layer of the soil (0-0.20 in) it was found 38.83% and 43.64% of the DM accumulated in the roots down to 2.00 in depth, in the cvs. Highworth and Rongai, respectively. In the deepest layer (1.80-2.00 in) it was found 3.02% and 1.5% of the DM accumulated in the roots of the cvs. Highworth and Rongai, respectively. The root density showed a striking decrease upper layer from the soil (0-0.2 m) down to the depth of 0.60 0.80 in (from 10.83 to 1.75 cm.cm(-3) in the cv. Highworth and from 10.76 to 1.28 cm.cm(-3) in the cv. Rongai). At the bottom layer (1.80-2.00 in) the root density values were 0.98 cm.cm(-3) and 0.59 cm.cm(-3), respectively for the cvs. Highworth and Rongai. The root/shoot ratios were similar in both cvs. and decreased from 42 to 70 DASE showing that the cvs. evaluated had the same dynamics of DM accumulation.

Fabrication of novel light-emitting devices based on green-phosphor/conductive-polymer composites

We report on light-emitting devices based on a green-phosphor compound (Mn-doped zinc silicate, Zn2SiO4: Mn) dispersed in a conductive polymeric blend (poly-o-methoxyaniline/polyvinylene fluoride, POMA/PVDF-TrFE). The devices exhibited high luminance in the green, good stability and homogeneous brilliance over effective areas up to 5 cm(2). The electroluminescence (EL) spectrum presented essentially the same characteristics as the photoluminescence (PL) and cathodoluminescence spectra, indicating that the light emission originates from decay of the same excited species, regardless of the excitation source. Operating characteristics were analyzed with current density - voltage (J - V) and luminance voltage ( L - V) curves to investigate the nature of the electroluminescence of the active material, which is still not completely understood.