Briquetting of charcoal from sugar-cane bagasse fly ash (scbfa) as an alternative fuel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Comparison of Deep Drawing and Ironing of Metal Alloy Strip Produced conventionally and Non-conventionally via Semi Solid Material Processing

A semi solid thin strip continuous casting process was used to obtain 50%wt Pb/50%wtSn strip by single and twin roll processing at speed of 15 m/min. A 50%wt Pb/50%wtSn plate ingot was also cast for rolling conventionally into strips of 1.4 mm thickness and 45 mm width for comparison with those achieved non-conventionally. This hypoeutectic alloy has a solidification interval and fusion temperature of approximately 31 degrees C and 215 degrees C respectively. The casting alloy temperature was around 280 degrees C as measured by a type K immersion thermocouple prior to pouring into a tundish designed to maintain a constant melt flow on the cooling slope during semi solid material production. A nozzle with a weir ensures that the semi solid material is dragged smoothly by the lower roll, producing strip with minimum contamination of slag/oxide. The temperatures of the cooling slope and the lower roll were also monitored using K type thermocouples. The coiled semi solid strip, which has a thickness of 1.5 mm and 45 mm width, was rolled conventionally in order to obtain 1.2 mm thick strip. The coiled thixorolled strip had a thickness of 1.2 mm and achieved practically the same width as the conventional strips. Blanks of 40 mm diameter were cut from the strips in a mechanical press, ready for deep drawing and ironing for mechanical characterization. All the strips achieved from non-conventional processing had the same mechanical performance as those achieved conventionally. The limiting drawing ratio (LDR) achieved was approximately 2.0 for all strips. Microscopy examination was made in order to observe phase segregation during processing.

Polycyclic aromatic hydrocarbons from wood pyrolyis in charcoal production furnaces

Polycyclic aromatic hydrocarbons (PAH) were measured in smoke samples from wood carbonization during charcoal production, in both particulate matter (PM) and gaseous phases. Samples were acquired using a medium-volume air sampler at 1.5 m distance from the furnace. Particle-bound PAH were collected on Fluoropore polytetrafluoroethylene filters and gas-phase PAH were collected into sorbent tubes with XAD-2 resin. PAH were extracted with dichloromethane-methanol and analyzed using gas chromatography-mass spectrometry. The results showed total emission from the furnace of 26 mu g/m(3) for the 16 PAH and 2.8 mu g/m(3) for the 10 genotoxic PAH (from fluoranthene to benzo[g,h,i]perylene). High emission of 16 PAH in the first 8 h of wood carbonization was detected (64 mu g/m(3); 56% of the total emission). Associated with PM, 11% of the total emission of 16 PAH (in both phases) and 60% of 10 genotoxic PAH were found. Relative ratios (for example, [Phe]/[Phe] + [Ant]) for the PAH of the same molecular weight were obtained and compared with the published data. The concentrations of benzo[a]pyrene equivalent (BaPeq) were estimated using the list of toxic equivalent factors suggested by Nisbet and LaGoy, 1992. The values of 0.30 and 0.06 mg/m3 were obtained for the total concentrations of BaPeq in PM and gaseous phase, respectively. (c) 2006 Elsevier B.V. All rights reserved.

Identification of polycyclic aromatic hydrocarbons and methoxylated phenols in wood smoke emitted during production of charcoal

More than 130 organic substances in dichloromethane-methanol (4: 1) extracts of particulate matter and the gaseous phase from wood burning for the production of charcoal have been identified by capillary gas chromatography coupled with low-resolution mass spectrometry (GC-MS), use of GC retention indices, and comparison with authentic standards. Many of the substances identified are methoxyphenols (derivatives of syringol and guaiacol), polycyclic aromatic hydrocarbons (PAH), oxidized PAH (oxy-PAH), and levoglucosan, the last being a monosoccharide derivative from the thermal breakdown of cellulose. The amount of unsubstituted PAH was greater than that of methyl- and dimethyl-substituted homologs.

Does spatial visualization ability improve after studying technical drawing?

Two studies were carried out to analyze whether learning technical drawing improves a person's ability for spatial visualization. Visualization and inductive reasoning tests were applied at the beginning and end of a course in technical drawing in samples of first year engineering students. In both studies it was observed that a moderate percentage of students improved their Visualization test execution. The improvement was similar in men and women. There was no improvement on the inductive reasoning test. The results support the conclusion that the spatial visualization ability can be improved with training.

Charcoal production using tropical pine thinnings

In Brazil, the wood from pine-plantation thinnings is difficult to sell. However, these wood thinnings could be used to produce charcoal. The physical and chemical properties of charcoal produced from logs or first and fourth thinnings of Pinus caribaea var. hondurensis and Pinus oocarpa were determined. Similar properties were also determined for sawmill slabs cut from first and fourth thinnings. Properties were compared to charcoal made from pine materials and 7-yr-old Eucalyptus grandis. Results show that Pinus spp had better chemical properties than did E. grandis. In contrast, charcoal obtained from E. grandis had higher values of apparent density and lower values of bulk density than did Pinus spp. © 1992.

Predicting academic success of engineering students in technical drawing from working memory

Tests on spatial aptitude, in particular Visualization, have been shown to be efficient predictors of the academic performance of Technical Drawing stu-dents. It has recently been found that Spatial Working Memory (a construct defined as the ability to perform tasks with a figurative content that require si-multaneous storage and transformation of information) is strongly associated with Visualization. In the present study we analyze the predictive efficiency of a bat-tery of tests that included tests on Visualization, SpatialWorking Memory, Spatial Short-term Memory and Executive Function on a sample of first year engineering students. The results show that Spatial Working Memory (SWM) is the most important predictor of academic success in Technical Drawing. In our view, SWM tests can be useful for detecting as early as possible those students who will require more attention and support in the teaching-learning process.

Damage and Loss Due to Ceratocystis fimbriata in Eucalyptus Wood for Charcoal Production

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A contribution to the identification of charcoal origin in brazil i - anatomical characterization of corymbia and eucalyptus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Operational and environmental assessment on the use of charcoal in iron ore sinter production

A study was carried out into the use of charcoal as a supplementary fuel in the iron-ore sintering process. The primary fuel was coke breeze and anthracite with 0, 10, 25, 50 and 100% replacement of the energy input with charcoal to produce sinter. This was achieved by considering the carbon content of each fuel and its corresponding participation on fuel blending, in order to have the same carbon input in each test run. An extensive analysis of the environmental impact was carried out regarding the atmospheric pollutants characterization (dust, sulphur dioxide, nitrogen oxides, carbon monoxide, carbon dioxide, methane, total hydrocarbons, and dioxins and furans). Experimental results indicate that fuel blending where 50% of the heat input was provided by charcoal may be comparable with those using 100% coke, under normal sintering conditions, and may result in a 50% reduction on greenhouse gas emission. It was also observed that while dust, methane and hydrocarbons emissions increased, the total dioxins and furans, expressed as polychlorinated dibenzodioxins/furans, decreased approximately 50% when compared with operation with 100% coke.