Concentração de tensões em peças e componentes estruturais - uma abordagem através do método dos elementos finitos

Any failure process that may occur in a part probably is located where the stress exceeded the level of resistance. When a part or component has a sharp change in geometry, such as slots, holes, grooves, bumps or other irregularities, there is an increased concentration of stress at a specific location of the part. The objective of this study is to determine the maximum stresses in structural parts and components using the equations of elasticity theory in conjunction with the stress concentration factor experiment and compare them with results obtained by finite element method

Distribuição de tensões em bocais de vasos de pressão

This work is to analyze the behavior of context concentrated stresses generated around a nozzle connected to a pressure vessel. For this analysis we used the finite element method via a computer interface, the software ANSYS WORKBENCH. It was first necessary to study and intensive training of the software used, and also a study of the ASME Code, Section VIII, which is responsible for the standards used in pressure vessels. We analyzed three cases, which differ primarily in the variation of the diameter of the nozzle in order to analyze the variation of the stresses according to the variation of the diameters. The nozzle diameters were 35, 75 and 105 mm. After the model designed vessel, a pressure was applied on the innervessel of 0.5 MPa. For the smallest diameter, was found the lowest tensions concentrated. Varying between 1 and 223 MPa. Increasing the diameter of the nozzle resulted in increased tensions concentrated around the junction nozzle /vessel. The maximum stresses increased by 78% when the value was increased in diameter from 35 to 75 mm. Since the increase in diameter from 75 to 105 mm, the values of the tensions increased around 43%. These figures emphasize that stress concentrations increased with increasing the diameter of the nozzles, but not linearly

Estudo de tensões residuais em juntas soldadas utilizando o método dos elementos finitos

Pós-graduação em Engenharia Mecânica - FEG

Comparação do custo e benefício entre o bloqueio ovariano com protocolo curto modificado e protocolo com antagonista em tratamentos de fertilização assisitida

Pós-graduação em Ginecologia, Obstetrícia e Mastologia - FMB

Bloqueio pericoal guiado por ultrassom: ensaio clínico randonizado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise das tensões em próteses implantossuportadas esplintadas, variando a localização dos implantes, pôntico e cantilever: estudo pelo método dos elementos finitos tridimensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise comparativa de tensões e deformações específicas em uma estrutura treliçada, utilizando abordagem experimental e pelo método de elementos finitos

The process of knowledge construction is associated with physical or mechanical view of the phenomenon. In mechanical engineering courses should supplement their courses with physical or virtual learning devices to aid visualization of these phenomena. For the purpose of improving the mechanical engineering department laboratory practice was developed, through a project, a didactic device a trellis. The purpose of this work is the detailed study by comparing the theoretical results with the experimental results collected through the specific strains collected in the Catman. The study was iniatially done with nodes made of aluminum, giving results with high errors not allowing a good conclusion of results. For best results were achieved an improvement of the structure with strict we support the lattice and, thus, further study and greater quality of lattice structure

Estudo das alterações das propriedades mecânicas em aço A-516 grau 70 soldado e submetido a tratamento térmico de alívio de tensões

Pressure vessels are equipments that require a great care because of their high cost and human life risk in case of fail, and its fabrication methods are different for each manufacturer. Normally, pressure vessels and its parts are fabricated by welding, which may change local properties of metals. The head of a pressure vessel is a very important structural component and it is fabricated by welding and mechanical conformation. Because its excellent mechanical properties, de steel A-516 Grade 70 is often used in manufacturing of large pressure vessels that are subjected to high pressure and temperature, but was verified that its mechanical resistance is decreased when submitted to a tension relief heat treatment. By experience it was defined that before mechanical conformation of the head of a large pressure vessel, the steel should be submitted to a stress relief heat treatment in order to facilitate the mechanical conformation, but there is no quantitative analysis to prove this method and study its possible risks. In the present work the steel A-516 Grade 70 demonstrated a decrease of its mechanical resistance when submitted to a stress relief heat treatment, but keeping above the minimum limit defined in the literature. By other side its ductility was substantially increased, being possible to deduce that the stress relief heat treatment before mechanical conformation is a viable e recommended technique, but with reservations. With the data acquired during the fabrication e preparation of the specimen and the result of the tests, it was possible to elaborate a welding procedure that provides the same results obtained in this present work

Profissionais de saúde como professores: tensões e potências nas práticas de ensino na atensão primária à saúde

Pós-graduação em Saúde Coletiva - FMB

A revista mexicana Frente a Frente: ambiguidades e tensões entre fotomontagens vanguardistas e gravuras

O objetivo desse artigo é refletir sobre a experiência visual da revista mexicana Frente a Frente (1934-1937) publicação da Liga de Escritores y Artistas Revolucionários – LEAR (1933-1938). Após apresentar a trajetória da revista procuramos investigar o projeto visual da publicação e a complexidade de uma revista engajada e a tensão entre propostas de cultura proletária, realismo socialista e vanguarda. Procuramos averiguar a circulação da vanguarda fotográfica entre Europa e México no período entre guerras. Interessa-nos em particular a experiência da utilização de fotografias e fotomontagens.

O impacto do preparo, da cerâmica e do contato oclusal na distribuição de tensões em facetas

Pós-graduação em Odontologia Restauradora - ICT

Influência da geometria oclusal e material restaurador na carga para fratura e distribuição de tensões em coroas totais

Pós-graduação em Odontologia Restauradora - ICT

A inserção da educação matemática crítica na escola pública: aberturas, tensões e potencialidades

Pós-graduação em Educação Matemática - IGCE

Influência do material oclusal na distribuição de tensões em próteses implantossuportadas unitárias

Objective: the aim of this study was to evaluate the influence of occlusal veneering material in single fixed implant-supported crowns through the 3-D finite element method. Material and methods: Four models were fabricated using the Rhinoceros 4.0, SolidWorks, and InVesalius softwares. Each model represented a block of mandibular bone with an external hexagon implant of 5 mm x 10 mm and different veneering materials including NiCr (1), porcelain (2), composite resin (3), and acrylic resin (4). An axial load of 200 N and an oblique load of 100 N were applied. Results: model (2) with porcelain veneering presented a lower stress concentration for the NiCr framework, followed by the composite resin and acrylic resin. The stress distribution to the implant and bone tissue was similar for all models. Conclusions: there is no difference of stress distribution to the implant and supporting structures by varying the veneering material of a single implant-supported prosthesis.

Influência da angulação do implante e tipo de intermediário na distribuição das tensões

The aim of this study was to evaluate the influence of implant angulation and abutment type (UCLA and Estheticone) on stress distribution in screw-retained implant-supported prostheses through photoelasticity. Three models were fabricated with photoelastic resin PL-2 (Vishay, Micro-Measurements Group, Inc Raleigh, N.C., USA) containing one external hexagon implant with 3.75x10mm (Master screw, Conexão Sistemas de Prótese Ltda., Arujá, São Paulo) with 0°, 17° and 30° degrees and a screw-retained prostheses with UCLA and Estheticone abutments. The assembly was positioned in a circular polariscope; axial and oblique (45° degrees) loads of 100N were applied in fixed points on the occlusal crown surfaces by a universal testing machine. The stress generated was photographed and analyzed qualitatively with appropriate software (Adobe Photoshop®). The results demonstrated the same number of fringes for both abutment types for each angulation, with fringes increasing in the same way. A higher number of fringes were closer in the oblique loading mode. It was concluded that there was no significant difference in stress distribution in prostheses with UCLA and Estheticone abutments. Higher stress concentrations were observed with increased implant angulation. Stress concentration and intensity were higher in the oblique load than in axial load application.