Evaluation of WC-10Ni thermal spray coating with shot peening on the fatigue strength of AISI 4340 steel

Fatigue failure is a result of a crack initiation and propagation, in consequence of a cyclical load. In aeronautical components as landing gear the fatigue strength is an important parameter to be considered in project, as well as the corrosion and wear resistance.The thermal sprayed HVOF technology it's normally used to protect components against wear and corrosion, and are being considerate an alternative to replace chromium by the aeronautical industry. With respect to fatigue life, the HVOF technique induces residual stress on the interface. In the case of tensile residual stresses, the initiation and propagation phases of fatigue process are accelerated; on the other hand, compressive residual stresses close to the surface may increase fatigue life. The technique to improve the coated materials fatigue strength is the shot peening process, which induces residual stress in the surface in order to delay the nucleation and propagation process.The aim of present study is to compare the influence of WC-10 Ni coating applied by HVOF on the fatigue strength of AISI 4340 steel, with and without shot peening. S-N curves were obtained in axial fatigue tests for material base, and tungsten carbide coated specimens. (C) 2010 Published by Elsevier Ltd.

Fatigue in AISI 4340 steel thermal spray coating by HVOF for aeronautic application

Currently, high-strength materials, particularly AISI 4340 steel, are used in several landing gear components. Due to the high resistance to wear and corrosion required, the components are usually coating by hard chromium. This treatment produces waste, such as Cr+ 6 (hexavalent chromium), generally after applying the coating of hard chromium which is harmful to health and the environment. The process HVOF (High-velocity-oxygen-fuel) is considered a promising technique for deposition of hard chromium alternative coatings, for example, coatings based on tungsten carbide. This technique provides high hardness and good wear strength and more resistance to fatigue when compared to AISI 4340 hard chromium coated. To minimize loss fatigue due to the process of deposition, shot peening is used to obtain a compressive residual stress. The aim of this study was to analyze the effects of the tungsten carbide thermal spray coating applied by the HVOF, in comparison to the conventional hard chromium electroplating on the AISI 4340 high strength steel behavior in fatigue. Optical microscopy and scanning electron microscopy were used to observe crack origin sites, thickness and adhesion of the coating. (C) 2010 Published by Elsevier Ltd.

Fatigue behavior of PVD coated Ti-6Al-4V alloy

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização de camadas nitrocementadas por plasma produzidas no aço inoxidável austenítico AISI 316L

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effects of a muscarinic type-2 antagonist on cardiorespiratory function and intestinal transit in horses anesthetized with halothane and xylazine

Objective-To evaluate the cardiorespiratory and intestinal effects of the muscarinic type-2 (M-2) antagonist, methoctramine, in anesthetized horses.Animals-6 horses.Procedure-Horses were allocated to 2 treatments in a randomized complete block design. Anesthesia was maintained with halothane (1% end-tidal concentration) combined with a constant-rate infusion of xylazine hydrochloride (1 mg/kg/h, IV) and mechanical ventilation. Hemodynamic variables were monitored after induction of anesthesia and for 120 minutes after administration of methoctramine or saline (0.9% NaCl) solution (control treatment). Methoctramine was given at 10-minute intervals (10 mug/kg, IV) until heart rate (HR) increased at least 30% above baseline values or until a maximum cumulative dose of 30 mug/kg had been administered. Recovery characteristics, intestinal auscultation scores, and intestinal transit determined by use of chromium oxide were assessed during the postanesthetic period.Results-Methoctramine was given at a total cumulative dose of 30 mug/kg to 4 horses, whereas 2 horses received 10 mug/kg. Administration of methoctramine resulted in increases in HR, cardiac output, arterial blood pressure, and tissue oxygen delivery. Intestinal auscultation scores and intestinal transit time (interval to first and last detection of chromium oxide in the feces) did not differ between treatment groups.Conclusions and Clinical Relevance-Methoctramine improved hemodynamic function in horses anesthetized by use of halothane and xylazine without causing a clinically detectable delay in the return to normal intestinal motility during the postanesthetic period. Because of their selective positive chronotropic effects, M-2 antagonists may represent a safe alternative for treatment of horses with intraoperative bracycardia.

Valor nutritivo da raiz e folhas da mandioca para a tilápia do nilo

The aim was to evaluate the nutritional value of the root and leaves of cassava (Manihot sculenta) for juveniles of Nile tilapia (Oreochromis niloticus). Three diets were prepared, a reference and two test diets. The first tested diet contained 50.0% of cassava root and 50.0% of reference diet and the second one consisted of 30.0% of cassava leaf meal and 70.0% of reference diet. Moreover, in every diet was added 0.1% chromium oxide-III (Cr2O3) as inert marker. Sixty juveniles (100.0 +/- 9.0 g) were accommodated in cages (10 fish/cage) for feeding and feces collection. During the day these cages were maintained in a feeding tank (250 L), one tank for each treatment, where they were fed until apparent satiation. After the aforementioned feeding period they were transferred to a fecal collection tank, where they remained until next morning. The collected feces were frozen and dried for analyzes. The apparent digestibility coefficients (ADC) were calculated on basis of Cr2O3 concentration present in diets and feces. The ADC of reference diet for DM, cassava leaf and root were, respectively 85.23%, 81.22% and 91.44%; CP to 97.35%, 73.37% and 91.46% and for the GE to 87.70%, 64.70% and 92.20%, the values obtained for the diet with cassava root significantly higher (P<0.05). Summarizing, root and cassava leaves can be used as alternative ingredients for compose balanced diets for Nile tilapia juveniles.

Diminuição do teor de óxido de crômio (III) usado como marcador externo

A sensibilidade do método espectrofotométrico da s-difenilcarbazida de determinação do crômio permite que esse metal possa ser determinado em teores e em massas de amostras tão pequenas que as concentrações atualmente usadas de óxido de crômio (III) como marcador externo em ensaios biológicos poderiam ser drasticamente diminuídas. Utilizando-se do piauçu (Leporinus macrocephalus) para um estudo sobre o coeficiente de digestibilidade aparente (CDA) da fração protéica, seis níveis de óxido de crômio (III) - 0,01% - 0,02% - 0,03% - 0,05% - 0,1% e 0,2% - foram incorporados em dietas isoprotéica e isoenergética, objetivando-se verificar se o cálculo do CDA seria afetado pela variação do teor do marcador. Os seis tratamentos foram dispostos em um delineamento em blocos inteiramente casualisados, sendo as fezes coletadas durante 16 dias. Verificou-se que os resultados do coeficiente de digestibilidade aparente da fração protéica não apresentaram diferenças estatísticas significativas devidas aos teores incorporados do marcador à ração e aos dias de coleta. Conseqüentemente, e em experimentos dessa natureza, nada impede que seja reduzido o teor de óxido de crômio (III) ao menos até 0,01%: além da economia relativa ao consumo do mesmo e da facilidade na manipulação de menor quantidade de amostras de fezes, o método espectrofotométrico da s-difenilcarbazida permite dosar esse nível (e até menor do que 0,01%) de modo simples e rápido, com precisão e exatidão.

Desempenho e qualidade da carne de bovinos Nelore e F1 Brangus × Nelore recebendo suplemento com cromo complexado à molécula orgânica na terminação a pasto

Objetivou-se avaliar o efeito da suplementação com cromo complexado à molécula orgânica do suplemento no desempenho produtivo, nas características de carcaça e na qualidade da carne de bovinos terminados em regime de pastagem. Foram utilizados 18 bovinos Nelore e 18 F1 Brangus × Nelore castrados, com 16 meses de idade, mantidos com suplementação mineral protéica, com ou sem cromo complexado à molécula orgânica e abatidos aos 22 meses de idade. O ganho médio diário de peso vivo (GMD) não diferiu entre grupos genéticos, entretanto animais mantidos com suplemento contendo cromo apresentaram maior GMD (494 g) em comparação aos demais (420 g). A adição de cromo orgânico no suplemento não promoveu alterações na área de olho-de-lombo (63,42 cm²) e na espessura de gordura subcutânea do dorso (5,46 mm) e da garupa (5,58 mm), tomados por meio do ultra-som. O peso médio de carcaça quente foi 235 kg e o rendimento médio de carcaça quente, 52,09%, com superioridade do suplemento contendo cromo (238 kg e 52,9%) em relação ao controle (231 kg e 51,2%). Animais Nelore e F1 Brangus × Nelore apresentam potencial similar de produção de carne a pasto. A suplementação mineral protéica com adição de cromo complexado à molécula orgânica aumenta o ganho de peso e o rendimento de carcaça, mas não influencia os parâmetros qualitativos da carne.

Influence of Crown Ferrule Heights and Dowel Material Selection on the Mechanical Behavior of Root-Filled Teeth: A Finite Element Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preload Evaluation of Different Screws in External Hexagon Joint

Purpose: This study compared the maintenance of tightening torque in different retention screw types of implant-supported crowns.Materials and Methods: Twelve metallic crowns in UCLA abutments cast with cobalt-chromium alloy were attached to external hexagon osseointegrated implants with different retention screws: group A: titanium alloy retention screw; group B: gold alloy retention screw with gold coating; group C: titanium alloy retention screw with diamond-like carbon film coating; and group D: titanium alloy retention screw with aluminum titanium nitride coating. Three detorque measurements were obtained after torque insertion in each replica. Data were evaluated by analysis of variance (ANOVA), Tukey's test (P < 0.05), and t test (P < 0.05).Results: Detorque value reduced in all groups (P < 0.05). Group A retained the highest percentage of torque in comparison with the other groups (P < 0.05). Groups B and D retained the lowest percentage of torque without statistically significant difference between them (P < 0.05).Conclusions: All screw types exhibited reduction in the detorque value. The titanium screw maintained the highest percentage of torque whereas the gold-coated screw and the titanium screw with aluminum titanium nitride coating retained the lowest percentage. (Implant Dent 2012;21:46-50)

The Effect of Mechanical Cycling and Different Misfit Levels on Vicker's Microhardness of Retention Screws for Single Implant-Supported Prostheses

Purpose: The aim of this study was to evaluate the effect of mechanical cycling and different misfit levels on Vicker's microhardness of retention screws for single implant-supported prostheses.Materials and Methods: Premachined UCLA abutments were cast with cobalt-chromium alloy to obtain 48 crowns divided into four groups (n = 12). The crowns presented no misfit in group A (control group) and unilateral misfits of 50 mu m, 100 mu m, and 200 mu m in groups B, C, and D, respectively. The crowns were screwed to external hexagon implants with titanium retention screws (torque of 30 N/cm), and the sets were submitted to three different periods of mechanical cycling: 2 x 10(4), 5 x 10(4), and 1 x 10(6) cycles. Screw microhardness values were measured before and after each cycling period. Data were evaluated by two-way ANOVA and Tukey's test (p < 0.05).Results: Mechanical cycling statistically reduced microhardness values of retention screws regardless of cycling periods and groups. In groups A, B, and C, initial microhardness values were statistically different from final microhardness values (p < 0.05). There was no statistically significant difference for initial screw microhardness values (p > 0.05) among the groups; however, when the groups were compared after mechanical cycling, a statistically significant difference was observed between groups B and D (p < 0.05).Conclusions: Mechanical cycling reduced the Vicker's microhardness values of the retention screws of all groups. The crowns with the highest misfit level presented the highest Vicker's microhardness values.

Model for the Evaluation of Root Wear by Histometric Analysis

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Shear bond strength of aesthetic materials bonded to Ni-Cr alloy

Objectives. This study was undertaken to evaluate the shear bond strength of four materials used as aesthetic material bonded to Ni-Cr alloy.Methods. Sixty-eight alloy discs were prepared and divided equally into four groups, and received four treatments for veneering: conventional feldspathic porcelain (Noritake EX-3) and three light-cured prosthodontic composite resins (Artglass, Solidex and Targis). The aesthetic materials were applied after metal structure conditioning in accordance with the manufacturers' recommendations. The specimens were stored in distilled water at 37 degreesC for 7 days. A universal testing machine was used to measure the shear bond strength of the specimens at a cross head speed of 0.5 mm/min. Fractured specimens were examined by using both optical and scanning electron microscope.Results. The analysis of variance and Tukey's test showed that the strongest mean shear bond was obtained with Noritake EX-3 (mean shear bond strength 42.90 +/- 7.82 MPa). For composites, the highest mean shear bond strength was observed for Targis (12.30 +/- 1.57 MPa); followed by Solidex (11.94 +/- 1.04 MPa) and Artglass (10.04 +/- 0.75 MPa). Optical analysis of the fractured surf aces indicated that for Targis and Noritake EX-3 all failures were a mixture of both cohesive and adhesive patterns. As for Artglass and Solidex, the fractures were mainly adhesive in nature.Conclusions. The Solidex system was equivalent to the Targis system in bond strength and exhibited greater strength than the Artglass system. The porcelain fused-to-metal showed considerably higher shear bond strength than the three metal-resin bonding techniques. (C) 2003 Elsevier B.V. Ltd. Ali rights reserved.

Shear bond strength of metal-ceramic repair systems

Statement of problem. When clinical fractures of the ceramic veneer on metal-ceramic prostheses can be repaired, the need for remake may be eliminated or postponed. Many different ceramic repair materials are available, and bond strength data are necessary for predicting the success of a given repair system.Purpose. This study evaluated the shear bond strength of different repair systems for metal-ceramic restorations applied on metal and porcelain.Material and methods. Fifty cylindrical specimens (9 X 3 mm) were fabricated in a nickel-chromium alloy (Vera Bond 11) and 50 in feldspathic porcelain (Noritakc). Metal (M) and porcelain (P) specimens were embedded in a polyvinyl chloride (PVC) ring and received I of the following bonding and resin composite repair systems (n=10): Clearfil SE Bond/Clearfil AP-X (CL), Bistite II DC/Palfique (BT), Cojet Sand/Z100 (Q), Scotchbond Multipurpose Plus/Z100 (SB) (control group), or Cojet Sand plus Scotchbond Multipurpose Plus/Z100 (CJSB). The specimens were stored in distilled water for 24 hours at 37 degrees C, thermal cycled (1000 cycles at 5 degrees C to 55 degrees C), and stored at 37 degrees C for 8 days. Shear bond tests between the metal or ceramic specimens and repair systems were performed in a mechanical testing machine with a crosshead speed of 0.5 mm/min. Mean shear bond strength values (MPa) were submitted to 1-way ANOVA and Tukey honestly significant difference tests (alpha=.05). Each specimen was examined under a stereoscopic lens with X 30 magnification, and mode of failure was classified as adhesive, cohesive, or a combination.Results. on metal, the mean shear bond strength values for the groups were as follows: MCL, 18.40 +/- 2.88(b); MBT, 8.57 +/- 1.00(d); MCJ, 25.24 +/- 3.46(a); MSB, 16.26 +/- 3.09(bc); and MCJSB, 13.11 +/- 1.24(c). on porcelain, the mean shear bond strength values ofeach group were as follows: PCL, 16.91 +/- 2.22(b); PBT, 18.04 +/- 3.2(ab); PCJ, 19.54 +/- 3.77(ab); PSB, 21.05 +/- 3.22(a); and PCJSB, 16.18 +/- 1.71(b). Within each substrate, identical superscript letters denote no significant differences among groups.Conclusions. The bond strength for the metal substrate was significantly higher using the Q system. For porcelain, SB, Q, and BT systems showed the highest shear bond strength values, and only SB was significantly different compared to CL and CJSB (P <.05).

EFFECT of DIFFERENT AIRBORNE-PARTICLE ABRASION/BONDING AGENT COMBINATIONS on THE BOND STRENGTH of A RESIN CEMENT TO A BASE METAL ALLOY

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)