Erbium and ytterbium co-doped SiO2 : GeO2 planar waveguide prepared by the sol-gel route using an alternative precursor

The sol-gel method combined with a spin-coating technique has been successfully applied for the preparation of rare-earth doped silica:germania films used for the fabrication of erbium-doped waveguide amplifiers (EDWA), presenting several advantages over other methods for the preparation of thin films. As with other methods, the sol-gel route also shows some drawbacks, such as cracks related to the thickness of silica films and high hydrolysis rate of certain precursors such as germanium alkoxides. This article describes the preparation and optical characterization of erbium and ytterbium co-doped SiO2:GeO2 crack-free thick films prepared by the sol-gel route combined with a spin-coating technique using a chemically stable non-aqueous germanium oxide solution as an alternative precursor. The non-crystalline films obtained are planar waveguides exhibiting a single mode at 1,550 nm with an average thickness of 3.9 mu m presenting low percentages of porosity evaluated by the Lorentz-Lorenz Effective Medium Approximation, and low stress, according to the refractive index values measured in both transversal electric and magnetic polarizations. Weakly confining core layers (0.3% < Delta n < 0.75%) were obtained according to the refractive index difference between the core and buffer layers, suggesting that low-loss coupling EDWA may be obtained. The life time of the erbium I-4(13/2) metastable state was measured as a function of erbium concentration in different systems and based on these values it is possible to infer that the hydroxyl group was reduced and the formation of rare-earth clusters was avoided.

NIR luminescent Er3+/Yb3+ co-doped SiO2-ZrO2 nanostructured planar and channel waveguides: Optical and structural properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Visible and near-infrared luminescent Eu3+ or Er3+ doped laponite-derived xerogels and thick films: Structural and spectroscopic properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da enxertia hipocotiledonar do maracujazeiro-amarelo sobre dois porta-enxertos, através de microscopia eletrônica de varredura

O objetivo deste trabalho foi verificar quanto tempo após a realização da enxertia hipocotiledonar ocorre a soldadura ou adesão entre enxerto e porta-enxerto, e também a formação da ponte de calo, verificada pelo total preenchimento da fenda por tecido meristemático secundário (calo). Foram produzidas 56 mudas de maracujazeiro-amarelo (Passiflora edulis Sims f. flavicarpa Deg.) pela enxertia hipocotiledonar em fenda cheia no topo sobre dois porta-enxertos (P. edulis Sims f. flavicarpa Deg. e P. alata Dryander). Aos 0, 3, 6, 9, 12, 15 e 18 dias após a enxertia, coletou-se a região da enxertia de quatro mudas de cada combinação. O material coletado foi fixado em solução de glutaraldeído a 3%, pós-fixado em tetróxido de ósmio a 2%, desidratado em uma série de álcool etílico (30, 40, 50, 60, 70, 80, 90, 100%), levado ao secador de ponto crítico (CO2), montado, metalizado com ouro - paládio (35 nm) e, por fim, observados e eletromicrografados em microscópio eletrônico de varredura JEOL JSM 5410 (operado em 15 kV). Verificou-se que, aos seis dias após a enxertia, a soldadura para o porta-enxerto Passiflora alata já havia ocorrido, o que só foi constatado para Passiflora edulis f. flavicarpa aos nove dias. Também, aos nove dias, observou-se para ambos os porta-enxertos a completa formação da ponte de calo, indicando que, a partir daí, pode-se iniciar o processo de aclimatação da muda, para levá-la a um ambiente de menor umidade.

Anestesia e o usuário de Ecstasy

JUSTIFICATIVA E OBJETIVOS: Nos últimos anos o número de novos usuários de agentes ilícitos tem aumentado de forma significativa em todo o mundo. A maconha e a cocaína, além do álcool e do tabaco, têm sido os agentes citados com freqüência, porém houve um aumento significativo de usuários de outros agentes psicoestimulantes ou alucinógenos, como o Ecstasy, o GHB, o LSD e a metanfetamina, empregados com o objetivo de intensificar as experiências sociais. O objetivo do presente artigo foi discutir a apresentação clínica, os efeitos deletérios e as potenciais interações com o ato anestésico no paciente cirúrgico usuário desses agentes ilícitos. CONTEÚDO: O artigo discute os mecanismos de ação, a apresentação clínica, os efeitos deletérios e as possíveis repercussões observadas durante a anestesia no usuário de MDMA (3,4-metilenodioximetanfetamina), também conhecido como Ecstasy. CONCLUSÕES: A apresentação clínica e os efeitos deletérios provocados pelo 3,4-metilenodioximetanfetamina (Ecstasy), assim como potenciais interações com o ato anestésico devem ser do conhecimento do anestesiologista, pois em muitas situações esses usuários serão submetidos a intervenções cirúrgicas de emergência, ou mesmo eletivas.

Avaliação da qualidade do corte florestal com motosserra

Objetivou-se, com esta pesquisa, avaliar a qualidade do corte florestal com motosserra, em propriedades rurais no sul do Espírito Santo, considerando aspectos da qualidade e a perda de madeira retida nas cepas. Foram lançadas parcelas de 250 m², onde foram feitas as observações após o corte com motosserra, avaliando-se a qualidade do corte nos seguintes aspectos: presença de espetos; danos por rachadura; cepas com faixa de ruptura fora do padrão; cepas sem o entalhe direcional e a altura da cepa remanescente, com vistas a mensurar a perda de madeira retida nas cepas. de acordo com os resultados, em média, houve presença de espetos em 21,9% das cepas, de rachaduras em 17,2%, de cepas fora do padrão em 44,6% e de cepas sem entalhe direcional em 34,5% das avaliações. Para verificar a influência da realização do entalhe direcional na altura das cepas, o teste-t, a 5% de probabilidade demonstrou que há contribuição para ocorrer maior altura de cepas, nos casos em que o corte foi feito sem o entalhe direcional. A quantidade de madeira retida nas cepas, acima do máximo recomendado, foi, em média, de 2,43 m³/ha, representando um prejuízo de R$ 172,53/ha. Foi verificada que a perda de madeira remanescente nas cepas de eucalipto foi maior nos locais onde, para a derrubada das árvores, não houve a realização do entalhe direcional. Os itens avaliados demonstraram qualidade irregular, indicando a necessidade de melhoria no corte com motosserras.

Evaluation of shot peening on the fatigue strength of anodized Ti-6Al-4V alloy

The increasingly design requirements for modern engineering applications resulted in the development of new materials with improved mechanical properties. Low density, combined with excellent weight/strength ratio as well as corrosion resistance, make the titanium attractive for application in landing gears. Fatigue control is a fundamental parameter to be considered in the development of mechanical components. The aim of this research is to analyze the fatigue behavior of anodized Ti-6Al-4V alloy and the influence of shot peening pre treatment on the experimental data. Axial fatigue tests (R = 0.1) were performed, and a significant reduction in the fatigue strength of anodized Ti-6Al-4V was observed. The shot peening superficial treatment, which objective is to create a compressive residual stress field in the surface layers, showed efficiency to increase the fatigue life of anodized material. Experimental data were represented by S-N curves. Scanning electron microscopy technique (SEM) was used to observe crack origin sites.

Epitaxially grown LiNbO3 thin films by polymeric precursor method

LiNbO3 thin films were grown on (0001) sapphire substrates by a chemical route, using the polymeric precursor method. The overall process consists of preparing a coating solution from the Pechini process, based on metallic citrate polymerization, the precursor films, deposited by dip coating, are then heat treated to eliminate the organic material and to synthesize the phase. In this work, we studied the influence of the heat treatment on the structural and optical properties of single-layered films. Two routes were also investigated to increase the film thickness: increasing the viscosity of the coating solution and/or increasing the number of successively deposited layers. The x-ray diffraction theta -2 theta scans revealed the c-axis orientation of the single- and multilayered films and showed that efficient crystallization can be obtained at temperatures as low as 400 degreesC, the phi-scan diffraction evidenced the epitaxial growth with two in-plane variants, A microstructural study revealed that the films were crack free, homogeneous, and relatively dense. Finally, the investigation of the optical properties (optical transmittance and refractive index) confirmed the good quality of the films. These results indicate that the polymeric precursor method is a promising process to develop lithium niobate waveguides.

Fatigue life studies in carbon dual-phase steels

An investigation has been conducted to examine the morphological influence on fatigue life of low carbon steel with dual phase microstructure. The results showed that dual-phase microstructure, composed by ferrite and martensite had superior symmetrical bending fatigue strength when compared with ferrite-pearlite steel. Through those tests, evidences of different mechanisms were verified (such as ferrite cyclic hardening, slip band formation and beginning of crack nucleation and propagation). Based on the fatigue tests results, various mechanisms stages were discussed associated with different microstructure morphology. Copyright (C) 1996 Published by Elsevier B.V. Limited.

Study on the orientation degree of Pb1-xLaxTiO3 thin films by the rocking curve technique and its morphological aspects

Thin films of perovskite-type materials such as PbTiO3, BaTiO3, (Pb,La)TiO3, (Pb, La)(ZrTi)O-3, KNbO3, and Pb(Mg,Nb)03 have been attracting great interest for applications like non-volatile memories, ultrasonic sensors and optical devices. Thin film should be epitaxially grown or at least highly textured since the properties of this anisotropic material depend on the crystallographic orientation. For optical devices, in particular, an epitaxial thin film without defects are essential to reduce optical propagation losses. Pb1-xLaxTiO3 (PLT) where x=0, 13 and 27% thin films were prepared by a chemical method (polymeric precursors method), and deposited by the spin coating technique onto substrates of SrTiO3 (STO) and LaAlO3 (LAO). The films were then beat treated at 500 degrees C in a controlled atmosphere of 0,. The orientation degree of the thin films was obtained from rocking curve technique, by means of X-ray difftaction analysis. A microstructural study revealed that the films were crack-free, homogeneous and have low roughness. (c) 2006 Elsevier B.V. All rights reserved.

INVOLVEMENT OF SWIMMING-INDUCED ACUTE STRESS IN THE SENSITIVITY OF RAT VAS-DEFERENS TO NOREPINEPHRINE

1. The effects of swimming-induced stress on rat sensitivity to norepinephrine were studied.2. Through microscopic analysis of the stomach from swimming stressed rats significant ulceration was observed, confirming that the stress situation was really present.3. Sensitivity to norepinephrine either in the presence or in the absence of cocaine and propranolol in acutely swimming stressed rats was not altered significantly.4. Bilateral adrenalectomy was performed in rats 2 days before swimming and acute stress resulted in a supersensitivity to norepinephrine, indicating that adrenal glands may, at least, partially mediate the sensitivity to this drug in vasa deferentia isolated from these animals.

Microstructural, dielectric and ferroelectric properties of calcium-modified lead titanate thin films derived by chemical processes

Ferroelectric Pb1-xCaxTiO3 (x = 0.24) thin films were formed on a Pt/Ti/SiO2/Si substrate by the polymeric precursor method using the dip-coating technique for their deposition. Characterization of the films bq X-ray diffraction showed a perovskite single phase with a tetragonal structure after annealing at 700 degreesC. Atomic force microscopy (AFM) analyses showed that the film had a smooth and crack-free surface with low surface roughness. In addition, the PCT thin film had a granular structure with an 80 nm grain size. The thickness of the films observed by the scanning electron microscopy (SEM) is 550 nm and there is a good adhesion between the film and substrate. For the electrical measurements metal-ferroelectric-metal of the type capacitors were obtained, where the thin films showed good dielectric and ferroelectric properties. The dielectric constant and dissipation factor at 1 kHz and measured at room temperature were found to be 457 and 0.03. respectively. The remanent polarization and coercive field for the: deposited films were P-r = 17 muC/cm(2) and E-c = 75 kV/cm, respectively. Moreover. The 550-nm-thick film showed a current density in the order of 10(-8) A/cm(2) at the applied voltage of 2 V. The high values of the thin film's dielectric properties are attributed to its excellent microstructural quality and the chemical homogeneity obtained by the polymeric precursor method. (C) 2001 Elsevier science Ltd. All rights reserved.

Microstructure and dielectric properties of (Ba,Sr)TiO3 thin film produced by the polymeric precursor method

BaxSr1-xTiO3 (x = 0.6) (BST) thin films were successfully prepared on a Pt(111)/TiO2/SiO2/Si(100) substrate by spin coating, using the polymeric precursor method. BST films with a perovskite single phase were obtained after heat treatment at 700 degrees C. The multilayer BST thin films had a granular structure will a grain size of approximately 60 nm. A 480-nm-thick film was obtained by carrying out five cycles of the spin-coating/heating process. Scanning electron microscopy and atomic force microscopy analyses showed that the thin films had a smooth, dense, crack-free surface with low surface roughness (3.6 nm). At room temperature and at a frequency of 100 kHz, the dielectric constant and the dissipation factor were, respectively, 748 and 0.042. The high dielectric constant value was due to the high microstructural quality and chemical homogeneity of the thin films obtained by the polymeric precursor method.

Preparation and properties of ferroelectric Pb1-xCaxTiO3 thin films produced by the polymeric precursor method

Pb1- xCaxTiO3 thin films with x = 0.24 composition were prepared by the polymeric precursor method on Pt/Ti/SiO2/Si substrates. The surface morphology and crystal structure, and the ferroelectric and dielectric properties of the films were investigated. X-ray diffraction patterns of the films revealed their polycrystalline nature. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses showed the surface of these thin films to be smooth, dense and crack-free with low surface roughness. The multilayer Pb1-xCaxTO3 thin films were granular in structure with a grain size of approximately 60-70 nm. The dielectric constant and dissipation factor were, respectively, 174 and 0.04 at a 1 kHz frequency. The 600-nm thick film showed a current density leakage in the order of 10(-7) A/cm(2) in an electric field of about 51 kV/cm. The C-V characteristics of perovskite thin films showed normal ferroelectric behavior. The remanent polarization and coercive field for the deposited films were 15 muC/cm(2) and 150 kV/cm, respectively. (C) 2001 Kluwer Academic Publishers.

Structural and electrical properties of SrBi2Nb2O9 thin films prepared by chemical aqueous solution at low temperature

SrBi2Nb2O9 (SBN) thin films were prepared by the polymeric precursors method and deposited by dip coating onto Pt/Ti/SiO2/Si(100) substrates. The dip-coated films were specular and crack-free and crystallized during firing at 700 degrees C. Microstructure and morphological evaluation were followed by grazing incident X-ray diffraction (GIXRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The films exhibited somewhat porous grain structure with rounded grains of about 100 nm. For the electrical measurements, gold electrodes of 300 mu m in diameter were sputter deposited on the top surface, forming a metal-ferroelectric-metal (MFM) configuration. The remanent polarization (P-r) and coercive field (E-c) were 5.6 mu C/cm(2) and 100 kV/cm, respectively. (C) 1999 Elsevier B.V. B.V. All rights reserved.