Eletro-oxidação de metanol e etanol sobre PtAu/C em meio alcalino

The development of electrocatalysts for the oxidation of methanol and ethanol is very important, because these alcohols may be used in the anode fuel cells which convert chemical energy directly into electrical energy with high efficiency, cleanly and with low noise. Thus, this study reports to the synthesis of nanocatalysts of PtAu supported on carbon by microemulsion method. The physical characterization of these catalysts is performed through the techniques of X-ray diffraction and transmission electron microscopy. The catalytic activity of the prepared materials was studied using conventional electrochemical techniques and also the technique of spectro-electrochemical in situ FTIR, which allows identification of intermediates and products of the reactions. From the x-ray diffraction, it was observed that the thermal treatment applied to catalysts favored incorporation of Au into the crystal lattice of Pt,that is, increased the formation of PtAu alloy. Micrographs indicated particle size about 3 nm to materials not heat treated and 9 nm to materials subjected to thermal treatment (heating at 150 ° C for 1h and 30 min in argon atmosphere). Current density oxidation of methanol on PtAu / C were superior to pure platinum. Spectroscopic results indicated the presence of formate in solution in 50:50 and the composition showed bands for CO2, indicating complete oxidation, in lower potential. During ethanol oxidation on the catalyst PtAu, the main product formed was acetate, product of incomplete oxidation. The good performance for methanol oxidation can be attributed to large amounts of oxygen species adsorbed on the catalyst surface, or an electronic effect.

Otimização de método para determinação de antimicrobianos em cama de frango por clae-flu

O extraordinário desenvolvimento da produção avícola, particularmente no setor de frango de corte, tornou o Brasil um importante produtor e exportador de carne de frango. Esse fato aliado a proibição da utilização de cama de frango como ração para ruminantes pela Instrução Normativa nº15 de 17 de julho de 2001, fez com que este resíduo se tornasse um problema ecológico e de saúde pública de alta relevância, tanto pelo volume de resíduos gerado, quanto pela composição do mesmo, que pode conter diversos fármacos utilizados neste tipo de manejo, além de uréia, que após a oxidação natural no ambiente, resulta em nitrato que tem alto poder de contaminação de mananciais hídricos, principalmente subterrâneos. Dentre as substâncias que podem estar presentes na cama de frango, estão os antimicrobianos, utilizados como promotores de crescimento das aves. No Brasil, são pouquíssimos os trabalhos dedicados a investigar a ocorrência e o impacto ambiental de antimicrobianos. Desta maneira, este trabalho teve como objetivo otimizar e validar método para análise de três fluoroquinolonas (ciprofloxacina, norfloxacina e enrofloxacina) em cama de frango. O método estudado baseou-se em trabalhos da literatura em que moléculas similares foram analisadas em diversas matrizes, compreendendo a extração em ultrassom com acetonitrila acidificada com ácido acético (3% v/v) e análise por CLAE-FLU, modo isocrático com a fase móvel composta por 0,02 M H3PO4:ACN (83:17, v/v). Foram avaliados os parâmetros cromatográficos quanto à resolução, eficiência, linearidade e limites de detecção e quantif-1 para os três analitos. O tempo de análise do método cromatográfico otimizado é de 7,5 minutos. Avaliou-se também o efeito de matriz que foi significativo para norfloxacina e ciprofloxacina, correspondendo a 16 e 20%, respectivamente. Para a enrofloxacina a amostra...

Compostos de paládio(II) contendo ligantes sulfurados: síntese, caracterização e investigação da atividade biológica

This work deals with the synthesis, spectroscopic characterization of mono and polynuclear Pd(II) compounds obtained from the reaction between [PdCl2(MeCN)2] precursor and imidazolidine-2-thione (L1) and benzimidazoline-2-thione (L2). The interaction between [PdCl2(MeCN)2] and imidazolidine-2-thione, in the 1:2 molar ratio, using MeOH as solvent, yielded compound [Pd2Cl4(L1)4]Cl2 (1) whereas the complex [Pd2Br4(L1)4]Br2 (2) was obtained from the reaction between 1 and Br- ions. Binuclear compounds of general formulae [Pd2(L2)4]X23/2 MeOH {X= Cl-(3), Br-(4)} were synthesized using benzimidazoline-2-thione as ligand, employing the same procedure used in the synthesis of 1 and 2, respectively. The new complexes 1-4 are crystalline, air stable and soluble in methanol and dmso. The compounds were characterized by elemental analysis, IR spectroscopy, ESI/MS mass spectrometry and thermogravimetry. Coordination of the ligands L1 and L2 via sulphur atom was evidenced by the shift of the CS band (~499 cm-1, 1 and 2; ~620 cm-1, 3 and 4) to lower frequencies in comparison with those found in the free ligands (510 cm-1, L1; 660 cm-1, L2), indicating the weakening of the CS bom after coordination. ESI/EM mass spectra (positive mode) of the complexes 1-4 allowed atribute the molecular formulae [Pd2X4(L1)4]X2 {X= Cl-(1), Br-(2)} and [Pd2(L2)4]X2 {X= Cl-(3), Br-(4)} by the appearance of the peaks at m/z 794,61 [(1) + MeOH]+, m/z 836,77 [(2) - 2H - L1]+, m/z 810 [(3) - 2Cl]+, m/z 810 [(4) - 2Br]+. The TG-DTA curves showed that the complexes 1 and 2 are thermally stable up to 212 and 169º C, respectively, and further decompose to metallic palladium at 527º C (1, obt. 28,46 %; calcd. 27,88%) and 895º C (2, obt. 22,85 %; calcd. 22,62%). Compounds 3 and 4 exhibited an initial mass loss of ~5% between 25 -146º C related to the release of metanol molecules. The complexes 3...Fujimura Leite.

Poluentes orgânicos persistentes em ar interior: desenvolvimento de método de extração em adsorvente para amostragem ativa

Persistent Organic Pollutants (POPs) are chemical substances extraordinarily toxic and persistent in the environment. Due to these properties, POPs are targets of the Stockholm Convention which aims to provide means to eliminate production and use by encouraging the reduction and, where possible, eliminating the release of these contaminants to the environment. One of the articles of this _Convention aims to assess the basal levels of such substances in the environment to monitor both the reduction of release to the environment, and to assess human exposure, using analyzes of milk and air for example. Although efforts to control POPs production and release to the environment have been made, data about their levels in Brazil are still scarce, mainly in the atmosphere or indoor environment. Considering the permanence of people inside its house, this study presents a method for POP extraction from XAD-2 sorbent employed in indoor air sampling, with identification and quantification by GC-ECD. GC-ECD linear range of the studied analytes, congeners of polychlorinated biphenyls (PCB) (28, 52, 101, 118, 138, 153 and 180), DDTs and their metabolites (DDDs, DDEs) and endosullan (isomers c - and 13 - and metabolite endosulfan sulfate) ranged between 0.5 and 16.0 ng mL-I with r2 > 0.967. The method developing consist of selecting the extraction solvent system by agitation (90 rpm, 1 hour) with n-hexan,e (2 mL) or n-hexane:acetone (1:1, v/v) (2 mL), concentration the extract with a gentle N2 stream, and evaluation of breakthrough with passage or air through the fortified XAD-2 cartridge before extraction, employing a low volume air suction pump (Pump Model 224 universal-PCXR8; 5-5000 mL min-1, SKC Inc., Eighty Four, PA, USA), Calibrator Dry-Cal DC-Lite (BIOS, Butler, NJ, USA)). Two fortification levels were employed, 15 and 30 ng. After selecting n-hexane as extraction solvent, with accuracy and precision ranging...

Determinação de fósforo em biodiesel utilizando eletrodo quimicamente modificado com nanopartículas de ferro

Once petroleum is na exhaustible source of energy, alternative fuels are having more prominence. A much discussed option for replacing fossil fuels is the use of biofuels derived from oils or fats, especially biodiesel. The biodiesel preparation is through a reaction named transesterification, a reaction of triglycerides with a short chain alcohol with a catalyst, producing a mixture of fatty acid esters and glycerol. According to ANP (National Petroleum Agency) specifications, biodiesel can have contaminants due to the catalyst or oil used on its synthesis, such as phosphorus, wich can damage the catalytic converter and cause significant increase in the particles emission. This project aims to develop na alternative method using chemically modified electrodes with iron nanoparticles for determination of phosphorus in biodiesel. For the formation of the iron nanoparticles film on the surface of a glassy carbon electrode, was used a iron sulfate solution. The film was formed after 10 successive cycles, with a scanning speed of 50 mV s-1 and a potential range of -0,9 to -1,25 V. To reduce possible oxides on the surface and activate the electrode, it has been subjected to a cathodic polarization with a potential of -1,25 V for 15 minutes in a sodium hydroxide solution. In cyclic voltammograms obtained in the study of the speed of scanning, there is an increase in the intensity of the anodic and cathodic current peaks. The cathodic peak current varied linearly with the square root of scan rate, showing that the electrode is controlled by diffusion. After successive additions of phosphate there is a linear variation in the current peak in the concentration range of 1,0 x 10-7 a 1,0 x 10-6 mol L-1. To determine if the concentration of phosphorus in real sample, the method of adding standard was used by adding aliquots of phosphate ions in the solution containing soy biodiesel extracted with ....

Filmes híbridos PMMA-siloxano modificados com nanotubos de carbono para proteção de materiais metálicos contra corrosão

Using the sol-gel process, organic-inorganic hybrid coatings were synthesized by incorporation of different concentrations of functionalized carbon nanotubes, to improve their mechanical strength and thermal resistance without changing its passivation character. The siloxane-PMMA hybrids were prepared by radical polymerization of methyl methacrylate (MMA) with 3-methacryloxipropiltrimethoxisilane (MPTS) using the thermal initiator benzoyl peroxide (BPO), followed by acid catalyzed hydrolysis and condensation of tetraethoxysilane (TEOS). The analysis of pristine and functionalized carbon nanotubes was carried out using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy and Raman Spectroscopy. Structural analysis of hybrids was performed by Nuclear Magnetic Resonance, Atomic Force Microscopy and Raman Spectroscopy. For analysis of mechanical strength and thermal stability were performed mechanical compression tests and thermogravimetric analysis, respectively. Electrochemical Impedance Spectroscopy was used to evaluate the corrosion resistance in saline environment. The results showed an effective functionalization of carbon nanotubes with carboxyl groups and conservation of its structure. The hybrids showed high siloxane network connectivity and roughness of approximately 0.3 nm. The incorporation of carbon nanotubes in the hybrid matrix did not change significantly their thermal stability. Samples containing carbon nanotubes exhibit good corrosion resistance (on the order of MΩ in saline environment), but the lack of complete dispersion of carbon nanotubes in the hybrid, resulted in a loss of mechanical and corrosion resistance compared to hybrid matrix.

Desenvolvimento de sistema de análise para valerato de estradiol baseado em polímeros biomiméticos

Abstracts : The development of analytic methods more selective and sensitive is of great importance for a better quality in the determination of chemical species, therefore increasing the reliability of the results. In this way, the optimization of separation/concentration is still necessary. The use of Molecularly Imprinted Polymers - MIPs have demonstrated to be an efficient tool of analysis with a great potential in minimizing limitations of separation/concentration techniques traditionally employed. In general, the MIPs are obtained by polymerization in the presence of a template to be imprinted so that a polymeric skeleton is formed around the future analyte. In the present work, the template used is Estradiol Valerate (EV), compound used in the hormone replacement therapy (HRT) during climacteric. After the polymerization in bulk and in an anaerobic environment using MAA, EGDMA, AIBN, acetonitrile and VE, the obtained MIP was powdered, sifted (<120 μm) and placed in a soxhlet system containing ethanol at 60 °C, in order to remove the imprinted molecule through six successive washes in periods of 24 hours. The water used in the washings was analyzed using HPLC and spectrophotometry UV/Vis. Then, the obtained MIP was dried at room temperature and 150 mg was inset in SPE cartridges in order to evaluate the polymer's efficiency in the analyte pre-concentration and extraction. To do so, 100,0 mL of VE standard solution (2mg L-1) were pre-concentrated at 4,0 mL min-1 and eluted with 10,0 mL ethanol at 1,0 mL min-1, obtaining recoveries of 53%. Additionally, a NIP (non-imprinting polymer) was prepared to compare the obtained results, in which the recovery was 80%. In the same way, studies were conducted using commercial Strata™-X cartridges, obtaining 53% recovery. Since, the results did not reflect that than was expected, in relation with the MIP efficiency in the recovery, a computational ...

Preparação e caracterização de novos híbridos orgânicos-inorgânicos baseados em carboximetilcelulose/polifosfato de sódio dopados com 'Eu'Cl IND.3

Organic- inorganic hybrid (HOI) are materials prepared with the combination of inorganic and organic components. The properties of a hybrid material are unique, not being the sum of each individual component added. This occurs because there is a synergism that depends of the chemical nature of organic and inorganic components, of the size and morphology of their domains. The sodium carboxymethylcellulose (CMC) it's an anionic polymer obtained of the cellulose, very soluble in water in which forms both solutions themselves and gels. The sodium polyphosphate (NaPO3)n, known commercially as Graham Salt is the only polyphosphate soluble in water, and it's the polyphosphate with the longest chain. At the present work it was prepared and characterized new phosphate organic- inorganic hybrids films of carboxymethylcellulose / sodium phosphate and luminescent films of CMC/NaPO3 doped with europium chloride (EuCl3). The films where prepared in several proportions. At first, it was set the amount of water to be used and the amount of carboxymethylcellulose, changing the concentrations of sodium polyphosphate and europium chloride. After pre-establishing concentrations, for each film, the components were submitted to constant agitation and subsequent drying. The inorganic-organic hybrid films were characterized by, TG, DR-X, DMA, FT-IR, UV-Vis-NIR, RMN 31P e 13C and at last, a study of luminescence was made. The hybrid films obtained are transparent and macroscopically homogeneous, however, the MET measures showed the formation of micro-islands of polyphosphate along the material, this fact indicates a bigger fragmentation of the films and this is verified by DMA analysis which shows a smaller resistance of the film with the increase of the concentration of phosphate. Both spectrum FT-IR and RMN analysis of the films, don't show the formation of new bands of their precursors, CMC e NaPO3,....

Uma nova abordagem analítica sobre teores de 'Zn' por HR-CSAAS em plantas medicinais voltadas ao emagrecimento

The following research project deals with the development of new analytical procedures aimed at the identification and quantification of the element zinc in different fractions of vegetable drugs used for weight loss, using the high-resolution continuum source atomic absorption spectrometry in flame. The determination of the levels of zinc was made in an AnalytikJena ContrAA 300 spectrometer in the principal line of Zn at 213.857 nm and wavelength integrated absorbance equal to 3 pixels. Calibration curves were obtained with linear dynamic range from 0.10 to 1.00 mg L-1, correlation coefficient equal to 0.9991 and limit of detection equal to 0.020 mg L-1. The total Zn content in the samples obtained after microwave-assisted acid digestion system were: 28.06 mg kg-1 (Artichoke), 31.49 mg kg-1 (Chamomile), 77.16 mg kg-1 (Gorse), 105.38 mg kg-1 (Horsetail), 32.37 mg kg-1 (Fennel) and 5.00 mg kg-1 (Senna). The extraction in aqueous environment assisted by microwave radiation produced extracts containing: 5.40 mg kg-1 (Artichoke), 10.65 mg kg-1 (Chamomile), 14.83 mg kg-1 (Gorse), 18.90 mg kg-1 (Horsetail), 7.80 mg kg-1 (Fennel), 3.24 mg kg-1 (Senna), corresponding to 19%, 34%, 19%, 18%, 24% and 64% of their total content of Zn, respectively. The amounts of Zn in the extracted samples from some plants indicate that this metal was strongly bounded to the plant's matrix. The sequential extraction using solvents and mixtures with different polarities (n-hexane, ethyl acetate, propanol, methanol, ethanol-water 1:1 (v/v), water) aimed the separation of different Zn containing species and water was considered the most efficient extractor. The Zn contents extracted were: 14.82 mg kg-1 (Artichoke), 16.82 mg kg-1 (Chamomile), 34.09 mg kg-1 (Gorse), 4.75 mg kg-1 (Senna), corresponding to 53% in the first two samples, 44% and 95% for the last two, respectively. It was observed that Zn is found complexed under

Síntese e caracterização da MOF NH2-MIL-125(Ti) e sua aplicação como catalisador na reação de condensação de Knoevenagel

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Nanopartículas de Pd suportadas em compósitos óxido-carbono: influência das interações metal-suporte na oxidação de etanol em meio básico

Fuel cells powered directly with ethanol (Direct Ethanol Fuel Cell-DEFC) are very attractive for the possibility of using a renewable fuel in the generation of clean energy. However, it is still necessary to deepen the understanding of catalytic processes and their dependence on the catalytic properties. This work proposes to study the catalytic activity of ethanol oxidation in an alkaline medium of Pd nanoparticles supported in carbon oxide hybrids using various transition metal oxides (MoO3, TiO2, WO3 and ZrO2). The materials prepared were characterized by techniques such as X-ray diffraction, transmission electron microscopy (TEM) and X-ray dispersive spectroscopy (EDX) to verify the structure, the distribution of particles in the supports and the presence of Pd on particles oxide. Experiments of X-rays absorption spectroscopy were carried out using soft X-rays (SXS) to evaluate the changes in the electronic properties of the Pd particles caused by interactions with different oxides. Measurements of cyclic voltammetry and potential sweeps of adsorbed CO oxidation allowed evaluating general aspects of the catalysts' electrochemical behavior and determining the electrochemically active area thereof. The catalytic performances of ethanol oxidation in alkaline medium were evaluated by electrochemical techniques (potential scan and chronoamperometry), and showed an improvement in activity with the addition of oxides in material containing only carbon, which was most pronounced for the catalyst containing TiO2. This improvement was predominantly associated with the electronic effects caused by the interaction of Pd on the support, causing a vacancy in the 4d band of Pd which, in turn, produces variations in adsorption energies of the species...

Estudo químico dos escapos de Paepalanthus geniculatus Kunth

Eriocaulaceae species are popularly known as sempre-vivas. This family comprising approximately 1.200 species divided into 10 genera, with high endemic levels. Paepalanthus genus has high incidence in the Espinhaço Range region and the report of biological activities. Despite the large number of previous studies with Eriocaulaceae species, Paepalanthus geniculatus has no studies about their scapes, which demonstrates the need for new research to identify their chemical and biological composition. The aim of this work was to study the chemical composition of P. geniculatus ethanolic extract seeking the isolation and identification of metabolites and evaluate the radical scavenging activity of the extract and isolated substances. P. geniculatus were collected in Serra do Cipó-MG in 2013 (Voucher: SANO 3193) and the scapes were dried, crushed and the powder was percolated with ethanol. With the etanolic extract it is carried out a fractionation by gel permeation chromatography, yielding fractions analyzed by TLC assay. The fraction J89 (45,6 mg) was purified by semipreparative HPLC-PDA, resulting in the isolation of substance S1. The fractionation was also performed by medium pressure liquid chromatography, yielding fractions analyzed by TLC assay. The fraction number 4 (92,6 mg) were purified by semipreparative HPLC-PDA resulting in the isolation of substances S2 and S3. The substances S1 and S3 were analyzed by mono and twodimensional NMR, resulting in the identification of 3,4-dihydroxybenzoic acid (protocatechuic acid) and the flavonoid 6-hydroxyquercetin-7-O-β-Dglucopyranoside. The substance S2 were identified by comparison with standards, were it was possible to determine the presence of the flavonoid 6-hydroxy-7- methoxyquercetin-3-O-β-D-glucopyranoside. The evaluation of radical scavenging activity for the extract and the isolated substances using DPPH, showed consistent activity to S1...

Estrutura e algumas propriedades ópticas de difenilfosfinatos de terras-raras

Coordination compounds of trivalent lanthanides cations with diphenylphosphinate are originated from direct reaction between a lanthanide salt and diphenylphosphinic acid. These complexes have peculiar and intriguing features, as (i) quickly obtainment through wet process precipitation, (ii) appreciable thermal stability, similar to inorganic phosphates, (iii) polymeric structure, and consequently, (iv) low solubility in both polar and non-polar solvents. Nowadays, coordination polymers are classified as coordination networks or, in case of porous materials, as metal-organic frameworks (MOFs). By this study, we aim to determine some optical properties of rare-earth diphenylphosphinate (RE = La3+, Eu3+, Gd3+, Lu3+) and conduct an updated classification of these compounds, bringing more details of its structure and the possible proposal of new materials with applications in lighting, detection of ionizing radiation and magnetism. The complexes of trivalent rare-earth cation with diphenylphosphinate were prepared by direct mixture of diphenylphosphinic acid with rare-earth metal chloride, both in ethanolic solution. The solution of diphenylphosphinic acid was kept in a beaker under constant stirring with pH measurements of the solution and gadolinium chloride solution was then dripped slowly with the aid of a burette until its complete addition; the following metal:ligand molar ratios were tested: 1:1, 1:2, 1:3, 2:1 e 3:1. The compounds were characterized by spectroscopic and structural techniques. By Fourier Transform Infrared Spectroscopy (FT-IR), it was possible to check the total ionization of diphenylphosphinic acid in synthesized complexes, confirmed by the absence of the band type A, B, C related to ѵ(O-H) of the acid (2663 cm-1, 2168 cm-1, 1684 cm-1), as well as the disappearance of ѵ(P-OH)=961 cm-1. Furthermore, the occurrence of bands shifts of ѵ(POO-) [symmetrical and asymmetrical] of...

Propriedades estruturais e espectroscópicas de WO3 e WO3:Eu3+

Used as catalysts even in organic and inorganic molecules, as additives on catalysts, electrochromic films on smart windows the tungsten trioxide have been largely studied on the lasts decades, but there is just a few about it's luminescence. Using as precursors nitric acid and sodium tungstate the tungsten trioxide were been prepared thru wet process then treating on thermic and hydrothermal treatments. Where been evaluated the effects of methodology, nitric acid concentration, duration and temperature of treatments. The samples were characterized by X-ray diffraction (XRD), Raman scattering spectroscopy (RSS), Fourier transformed infrared spectroscopy, photoluminescence spectroscopy (PLS) and X-ray excited optical luminescence (XEOL). Hydrated phases of tungsten trioxide were obtained through hydrothermal treatments and the non-hydrated phases occur with thermic treatments. The acid concentration has the ability to determine the major phase formed as well the temperature determine the hydratation of the product. With lower temperatures dihydrate phase were preferable formed and with the rise of temperature, the water molecules were lost up to the fractionary hydratation and then the non-hydrated phase with higher temperatures depending on the atmosphere used on the thermal treatment. Doping the system with europium ions even substituting tungsten or in the interstices of the matrix were not been successful, as well the XEOL spectroscopy intensity were null and quite low for ultraviolet and visible excitation photoluminescence because of oxygen defect levels localized into the prohibited band.