Synthesis and thermal characterization of luminescent powers of terbium(III) with mixed ligands

This work deals with the synthesis and thermal decomposition of complexes of general formula: Ln(beta-dik)(3)L (where Ln=Tb(+3), beta-dik=4,4,4-trifluoro-1-phenyl-1,3butanedione(btfa) and L=1,10-fenantroline(phen) or 2,2-bipiridine(bipy). The powders were characterized by melting point, FTIR spectroscopy, LTV-visible, elemental analysis, scanning differential calorimeter(DSC) and thermogravimetry(TG). The TG/DSC curves were obtained simultaneously in a system DSC-TGA, under nitrogen atmosphere. The experimental conditions were: 0.83 ml.s(-1) carrier gas flow, 2.0 +/- 0.5 mg samples and 10 degrees C.min(-1) heating rate. The CHN elemental analysis of the Tb(btfa)(3)bipy and Tb(btfa)(3)phen complexes, are in good agreement with the expected values. The IR spectra evinced that the metal ion is coordinated to the ligands via C=O and C-N groups. The TG/DTG/DSC curves of the complexes show that they decompose before melting. The profiles of the thermal decomposition of the Tb(btfa)3phen and Tb(btfa)3bipy showed six and five decomposition stages, respectively. Our data suggests that the thermal stability of the complexes under investigation followed the order: Tb(btfa)(3)phen < Tb(btfa)(3)bipy.

Possible structural phase transitions on Bi2Sr2CaCu2Oy measured by anelastic spectroscopy

Anelastic spectroscopy measurements (internal friction) are sensitive tools for the study of defects in solids, in particular the mobility of interstitial oxygen. Samples of Bi2Sr2CaCu2Oy were analyzed after being submitted to two thermal treatments in vacuum, one at 973 K and another at 673 K. Anelastic spectroscopy measurements were performed using a torsion pendulum operating at around 38 Hz and at a temperature range of 88 and 700 K with heating rate of 1 K/min and vacuum better than 10(-5) Torr. Complex relaxation structures reversible with new thermal treatments were observed. These relaxation structures were attributed to O-M structural phase transitions. (c) 2005 Elsevier B.V. All rights reserved.

Evaluation of the isoflurane-sparing effects of lidocaine and fentanyl during surgery in dogs

Objective-To evaluate the isoflurane-sparing effects of lidocaine and fentanyl administered by constant rate infusion (CRI) during surgery in dogs.Design-Randomized prospective study.Animals-24 female dogs undergoing unilateral mastectomy because of mammary neoplasia.Procedures-After premedication with acepromazine and morphine and anesthetic induction with ketamine and diazepam, anesthesia in dogs (n = 8/group) was maintained with isoflurane combined with either saline (0.9% NaCl) solution (control), liclocaine (1.5 mg/kg [0.68 mg/lb], IV bolus, followed by 250 mu g/kg/min [113 mu g/lb/min], CRI), or fentanyl (5 mu g/kg [2.27 mu g/lb], IV bolus, followed by 0.5 mu g/kg/min [0.23 mu g/lb/min], CRI). Positive-pressure ventilation was used to maintain eucapnia. An anesthetist unaware of treatment, endtidal isoflurane (ETiso) concentration, and vaporizer concentrations adjusted a nonprecision vaporizer to maintain surgical depth of anesthesia. Cardiopulmonary variables and ETiso values were monitored before and after beginning surgery.Results-Heart rate was lower in the fentanyl group. Mean arterial pressure did not differ among groups after surgery commenced. In the control group, mean +/- SD ETiso values ranged from 1.16 +/- 0.35% to 1.94 +/- 0.96%. Fentanyl significantly reduced isoflurane requirements during surgical stimulation by 54% to 66%, whereas the reduction in ETiso concentration (34% to 44%) observed in the lidocaine group was not significant.Conclusions and Clinical Relevance-Administration of fentanyl resulted in greater isoflurane sparing effect than did liclocaine. However, it appeared that the low heart rate induced by fentanyl may partially offset the improvement in mean arterial pressure that would be expected with reduced isoflurane requirements.

Thermally stimulated depolarizations: Disclosing an approximate universality

This paper presents an approximate universality displayed by thermally stimulated depolarization currents ruled by stretched exponential relaxations when properly re-scaled. A visually perfect universality occurs especially when the energy and the heating rate are varied. It becomes somewhat poorer when the frequency factor or the stretched exponent changes. Empirical relations between the half widths and other pertinent parameters are given.

GIGAHERTZ CONDUCTIVITY OF PRESSED PELLETS OF CLO4--DOPED POLY(3-METHYLTHIOPHENE) OBTAINED FROM ELECTRON-SPIN-RESONANCE MEASUREMENTS

Gigahertz conductivity of pressed pellets of ClO4--doped poly( 3-methylthiophene) can be readily obtained from the asymmetry ratio (A / B) of the electron spin resonance line using Dyson's theory. The measurements were performed in three different frequencies, 1.3, 9.4, and 35 GHz. The temperature dependence of the gigahertz conductivity is sensitive to the heating rate, probably due to the ordering of the randomly assembled anions. (C) 1994 Academic Press, Inc.

Thermal behaviour of Tin(II) complex with 8-hydroxyquinolinate in the solid state

Tin(II) complexes with 8-hydroxyquinolinate in solid state have been obtained by adding aqueous ammonium to a solution containing stannous chloride and 8-hydroxiquinoline in medium of HCl and acetone up to pH 5 and 9, respectively. The products obtained show the same composition, Sn(C9H6ON)(2); however there are some differences regarding both the thermal behaviour in an oxidant atmosphere and morphology. These products were characterised by elemental and complexometric analysis, TG and DTA curves, infrared and X-ray diffractometry. TG curves show, above 448 K, the partial oxidation on air atmosphere of Sn(II) complexes to Sn(IV) complexes, SnO(C9H6ON)(2). This behaviour does not depend only on pH in which the compounds were obtained but also on the heating rate in TG curves. Sn(II) complexes volatilise almost completely on nitrogen atmosphere and partially on air atmosphere depending on the oxidation degree of the compound.

Kinetic evaluation of the pyrolysis of high density polyethylene over H-AlMCM-41 material

The AlMCM-41 material with Si/Al=50 was synthesized by hydrothermal method, using cethyltrimethylammonium as template. The protonic H-AlMCM-41 acid form was obtained by ion exchange with ammonium chloride solution and subsequent calcination. The characterization of the material by several techniques showed that a good-quality MCM-41 material was obtained. High-density polyethylene (HDPE) has been submitted to thermal degradation alone, and in presence of the exchanged H-AlMCM-41 catalyst at a concentration of 1: 1 in mass (H-AlMCM-41/HDPE). The reactor was connected on line to a gas chromatograph connected to a mass spectrometer. This process was evaluated by thermogravimetry (TG), from 350 to 600degreesC, under helium dynamic atmosphere, with heating rates of 5.0; 10.0 and 20.0 degreesC/min. From TG curves, the activation energy, calculated using a multiple heating rate integral kinetic method, decreased from 225.5 KJ.mol(-1), for the pure polymer (HDPE), to 184.7 KJ.mol(-1), in the presence of the catalyst (H-AlMCM-41/HDPE).

Influence of interstitial elements on internal friction measurements in Nb and Nb-Zr alloys

Internal friction and frequency measurements as a function of temperature have been carried out in Nb and Nb-Zr policrystalline samples, using a torsion pendulum in the temperature range between 300K and 700K the heating rate was 1K/min and the pressure was kept better than 5x10(-3) mbar. Metals with bce lattice containing solute atoms dissolved interstitially often show anelastic behaviour due to a process know as stress-induced ordering responsible for the appearance of Snoek peaks. In the Nb sample it has been identified two constituent peaks corresponding to the interstitial-matrix interactions (Nb-O and Nb-N), but for the Nb-Zr samples with interstitial solute concentrations very close to those measured for the unalloyed Nb, it was not observed any mechanical relaxation peaks due to the presence of oxygen and nitrogen in solid solution.

Growth and survival of pacu Piaractus mesopotamicus (Holmberg, 1887) juveniles reared in ponds or at different initial larviculture periods indoors

Five-day-old pacu larvae (Piaractus mesopotamicus) with average length and weight of 5.96 mm and 0.42 mg, respectively, were reared as follows: in a semi-intensive system with larvae stocked directly into fertilized ponds (IL0)-and an initial intensive larviculture system with larvae maintained in a laboratory for 3 (IL3), 6 (IL6) and 9 (IL9) days, before being transferred to fertilized ponds. During the indoor phase, larvae were fed Artemia nauplii. Intensive-culture survivals were high (95.6%, 86.4% and 83.8% for IL3, IL6 and IL9, respectively) and at the end of the 45-day period, the longer the larvae were kept in the intensive system, the better the juvenile survival in the ponds. IL9 and IL6 survival rates were 54.0% and 45.4%, respectively, significantly higher (P < 0.05) than IL0 (11%) and IL3 presented an intermediate rate (25.3%). Due to the low survival rate of IL0, length and weight were higher (P < 0.05) when compared to IL6 and IL9; and the differences between their survival rates affected size distribution of juveniles among treatments. Treatments, which resulted in high survival (IL6 and IL9), presented a great number of small fish. In contrast, IL0 and IL3 produced many large and extra large individuals. In general, the results indicate that pacu juvenile production by initial intensive larviculture (IL6 and IL9) was the most efficient method. Therefore, further studies should be conducted in order to improve larval growth in the laboratory and handling techniques in both the laboratory and ponds. (C) 2003 Elsevier B.V. B.V. All rights reserved.

Influence of experimental factors on results of thermogravimetric analysis

Thermogravimetric results are influenced by a series of experimental factors, such as furnace heating rate and atmosphere, velocity of carrier gas, sample mass, etc. In this work a practical evaluation of these parameters are showed for calcium oxalate, with teaching objectives, considering that undergraduate text books discuss but do not show experimental details for these cases.

SrTiO3 preparation through coprecipitation methods

Precursor powders to obtain SrTiO3 were prepared by using 8-hydroxyquinoline precipitant agent. The residues from the thermal decomposition, followed by TG/DTG/DTA, were characterized by XRD and it could be verified that the mixed oxides could be obtained varying the thermal decomposition conditions like atmosphere and heating rate. However, the morphology and crystallinity of these residues is highly affected by such variations. (C) 2000 Elsevier B.V. B.V. All rights reserved.

Preparation of 9/65/35 PLZT thin films deposited by a dip-coating process

Crack-free polycrystalline PLZT (Pb,a)(Zr,Ti)O-3 thin films with the perovskite structure were prepared by dir-coating using the Pechinis process. Lead acetate, hydrated lanthanum carbonate, zirconium n-propoxide and titanium isopropoxide were used as raw materials. The viscosity of the solution was adjusted in the range of 20 to 56 cP and the films were deposited by a dip-coating process on silicon (100) as substrate. Solutions with ionic concentration of 0.1 and 0.2 M were used. Thin film deposition was accomplished by dipping the substrates in the solution with control of withdrawal speed from 5 to 20 mm/min. The thin films were thermally treated in two steps: at 300 degreesC amid 650 degreesC. The influence of withdrawal speed. viscosity, heating rate and ionic concentration on the morphology of PLZT thin film was discussed. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Influence of Ag addition on the thermal behavior of the Cu-11 mass% Al alloy

In this work the influence of Ag additions on the thermal behavior of the Cu-11 mass% Al alloy was studied using differential scanning calorimetry, in situ X-ray diffractometry and scanning electron microscopy. The results indicated that changes in the heating rate shift the peak attributed to alpha phase formation to higher temperatures, evidencing the diffusive character of this reaction. The activation energy value for the alpha phase formation reaction, obtained from a non-isotherm kinetic model, is close to that corresponding to Cu atoms self diffusion, thus confirming that this reaction is dominated by Cu atoms diffusion through the martensite matrix.

Alterations in pulmonary structure by elastase administration in a model of emphysema in mice is associated with functional disturbances

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Structure and Properties of Barium Bismuth Titanate Prepared by Mechanochemical Synthesis

Bi4Ti4O15 [BBT], a member of Aurivillius bismuth-based layer-structure perovskites, was prepared from stoichiometric amounts of BaTiO3 [BT] and Bi4Ti3O12 [BIT] obtained via mechanochemical synthesis. Mechanochemical synthesis was performed in air atmosphere in a planetary ball mill. BBT ceramics were sintered at 1100C for 4 h without pre-calcination step within heating rate 10C/min. The formation of phase and crystal structure of BT, BIT and BBT were approved using X-ray analysis. The morphology of obtained powders and microstructure were exhamined using scanning electron microscopy. The electrical properties of sintered samples were carried out.