Magnetic field effects on the conductivity of organic bipolar and unipolar devices at room temperature

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Heat-treatment effects on the magnetic response of superconducting mesoscopic samples

The use of chemical methods in the synthesis of high-quality and small-size polycrystalline samples has been increased in recent years. In this work, a chemical route based on an aqueous precursor solution of metals followed by the addition of a water-soluble polymer formed by ethylenediaminetetraacetic acid (EDTA) and ethylene glycol (EG) was tested to produce superconducting mesoscopic YBa(2)Cu(3)O(7-gamma) samples. Different conditions of heat treatments and the effects of argon and oxygen atmospheres during the calcination steps were traced using X-ray diffraction (XRD), scanning electron microscopy (SEM) and magnetic measurements. (C) 2008 Elsevier B. V. All rights reserved.

Vacuum effects on massive spinor fields: S-1 x R-3 topology

The aim of this work was to investigate the role played by an external field on the Casimir energy density for massive fermions under S-1 x R-3 topology. Both twisted- and untwisted-spin connections are considered and the calculation in a closed form is performed using an alternative approach based on the combination of the analytic regularization method and the Euler-Maclaurin summation formula. It is shown that no mass scale appears in the final result and, therefore, Casimir effect arises only from the boundary conditions and vacuum fluctuations induced by the coupling with the external field.

Processing and hygrothermal effects on viscoelastic behavior of glass fiber/epoxy composites

Fiber reinforced epoxy composites are used in a wide variety of applications in the aerospace field. These materials have high specific moduli, high specific strength and their properties can be tailored to application requirements. In order to screening optimum materials behavior, the effects of external environments on the mechanical properties during usage must be clearly understood. The environmental action, such as high moisture concentration, high temperatures, corrosive fluids or ultraviolet radiation (UV), can affect the performance of advanced composites during service. These factors can limit the applications of composites by deteriorating the mechanical properties over a period of time. Properties determination is attributed to the chemical and/or physical damages caused in the polymer matrix, loss of adhesion of fiber/resin interface, and/or reduction of fiber strength and stiffness. The dynamic elastic properties are important characteristics of glass fiber reinforced composites (GRFC). They control the damping behavior of composite structures and are also an ideal tool for monitoring the development of GFRC's mechanical properties during their processing or service. One of the most used tests is the vibration damping. In this work, the measurement consisted of recording the vibration decay of a rectangular plate excited by a controlled mechanism to identify the elastic and damping properties of the material under test. The frequency amplitude were measured by accelerometers and calculated by using a digital method. The present studies have been performed to explore relations between the dynamic mechanical properties, damping test and the influence of high moisture concentration of glass fiber reinforced composites (plain weave). The results show that the E' decreased with the increase in the exposed time for glass fiber/epoxy composites specimens exposed at 80 degrees C and 90% RH. The E' values found were: 26.7, 26.7, 25.4, 24.7 and 24.7 GPa for 0, 15, 30, 45 and 60 days of exposure, respectively. (c) 2005 Springer Science + Business Media, Inc.

Hygrothermal effects on the shear properties of carbon fiber/epoxy composites

The environmental factors, such as humidity and temperature, can limit the applications of composites by deteriorating the mechanical properties over a period of time. Environmental factors play an important role during the manufacture step and during composite's life cycle. The degradation of composites due to environmental effects is mainly caused by chemical and/or physical damages in the polymer matrix, loss of adhesion at the fiber/matrix interface, and/or reduction of fiber strength and stiffness. Composite's degradation can be measure by shear tests because shear failure is a matrix dominated property. In this work, the influence of moisture in shear properties of carbon fiber/epoxy composites ( laminates [0/0](s) and [0/90](s)) have been investigated. The interlaminar shear strength (ILSS) was measured by using the short beam shear test, and Iosipescu shear strength and modulus (G(12)) have been determinated by using the Iosipescu test. Results for laminates [0/0](s) and [0/90](s), after hygrothermal conditioning, exhibited a reduction of 21% and 18% on the interlaminar shear strenght, respectively, when compared to the unconditioned samples. Shear modulus follows the same trend. A reduction of 14.1 and 17.6% was found for [0/0](s) and [0/90](s), respectively, when compared to the unconditioned samples. Microstructural observations of the fracture surfaces by optical and scanning electron microscopies showed typical damage mechanisms for laminates [0/0](s) and [0/90](s).

Hygrothermal effects on damping behavior of metal/glass fiber/epoxy hybrid composites

Continuous fiber/metal laminates (FML) offer significant improvements over current available materials for aircraft structures due to their excellent fatigue endurance and low density. Glass fibers/epoxy laminae and aluminum foil (Glare) are commonly used to obtain these hybrid composites. The environmental factors can limit the applications of composites by deteriorating the mechanical properties during service. Usually, epoxy resins absorb moisture when exposed to humid environments and metals are prone to surface corrosion. Therefore, the combination of the two materials in Glare (polymeric composite and metal). can lead to differences that often turn out to be beneficial in terms of mechanical properties and resistance to environmental influences. In this work. The viscoelastic properties. such as storage modulus (E') and loss modulus (E'), were obtained for glass fiber/epoxy composite, aluminum 2024-T3 alloy and for a glass fiber/epoxy/aluminum laminate (Glare). It was found that the glass fiber/epoxy (G/E) composites decrease the E' modulus during hygrothermal conditioning up to saturation point (6 weeks). However, for Glare laminates the E' modulus remains unchanged (49GPa) during the cycle of hygrothermal conditioning. The outer aluminum sheets in the Glare laminate shield the G/E composite laminae from moisture absorption. which in turn prevent, in a certain extent, the material from hygrothermal degradation effects. (c) 2005 Elsevier B.V. All rights reserved.

Considerations on corrosion and weld repair effects on the fatigue strength of a steel structure critical to the flight-safety

The aim of this study is to analyze the effects of corrosion and successive tungsten inert gas (TIC) welding repairs on the reverse bending fatigue strength of AISI 4130 steel used in components critical to the flight-safety. The tests were performed on hot-rolled steel plate specimens, 1.10 mm and 1.60 mm thick, by means of a SCHENK PWS equipment, with load ratio R = -1, constant amplitude, 30 Hz frequency and room temperature. It was observed that the reverse bending fatigue strength of AISI 4130 steel decreases due to the corrosion and the TIC welding and re-welding processes. (C) 2010 Elsevier Ltd. All rights reserved.

Repair Welding Effects on the Bending Fatigue Strength of AISI 4130 Aeronautical Steel used in a Critical to the Flight-Safety Structure

The aim of this study was to analyze the effect of successive TIG (tungsten inert gas) welding repairs on the reverse bending fatigue strength of AISI 4130 steel, which is widely used in components critical to the flight-safety. In order to simulate the abrupt maneuvers, wind bursts, motor vibration and helixes efforts, which generate cyclic bending loadings at the welded joints of a specific aircraft component called motor cradle, experimental reverse bending fatigue tests were carried out on specimens made from hot-rolled steel plate, 1.10 mm (0.043 in) thick, by mean of a SCHENK PWS equipment, with load ratio R = -1, under constant amplitude, at 30 Hz frequency and room temperature. It was observed that the bending fatigue strength decreases after the TIG (Tungsten Inert Gas) welding process application on AISI 4130 steel, with subsequent decrease due to re-welding sequence as well. Microstructural analyses and microhardness measurements on the base material, heat-affected zone (HAZ) and weld metal, as well as the effects of the weld bead geometry on the obtained results, have complemented this study.

Considerations about the welding repair effects on the structural integrity of an airframe critical to the flight-safety

Structures critical to the flight-safety are commonly submitted to several maintenance repairs at the welded joints in order to prolong the in-service life of aircrafts. The aim of this study is to analyze the effects of Tungsten Inert Gas (TIG) welding repair on the structural integrity of the AISI 4130 aeronautical steel by means of experimental fatigue crack growth tests in base-material, heat-affected zone (HAZ) and weld metal. The tests were performed on hot-rolled steel plate specimens, 0.89 mm thick, with load ratio R = 0.1, constant amplitude, at 10 Hz frequency and room temperature. Increase of the fracture resistance was observed in the weld metal but decreasing in the HAZ after repair. The results were associated to microhardness and microstructural changes with the welding sequence. (C) 2010 Published by Elsevier Ltd.

Revegetation and Soil Management Effects on Chemical Properties of a Saprolite Resulting from Deep Soil Removal

During the building of a hydroelectrical power plant at Ilha Solteira in the Parana River (Brazil), materials of a highly weathered soil Oxisol were extracted from a depth between 5 and 8 m for engineering works. This resulted in an abandoned depression area. The topsoil was not salvaged and the open pit was not backfilled, and as result vegetation hardly or not at all recovered. on the residual saprolite materials, an experimental field was established to assess different soil rehabilitation treatments. Field experiments were initiated in 1992. After soil tillage, two different crops and three different liming strategies were compared, giving six combinations. In addition, two uncropped control treatments, tilled and no-tilled, were established so that a total of eight treatments were assessed. The experimental design consisted of four randomized experimental blocks, which included a total of 32 plots with a plot area of 100 m(2). This experiment was used to study the effectiveness of the soil-reclamation treatments after a 9-year period. Soil samples were taken at three different depths (0-10, 10-20, and 20-40 cm), and they were analyzed routinely for pH, organic-matter content, and cation exchange capacity (CEC). Revegetation of the abandoned saprolite material increased soil organic-matter content and cation exchange capacity (CEC), and to some extent small differences between treatments were evidenced. Exchangeable calcium (Ca) and magnesium (Mg) recovered faster than organic-matter content. A significant linear relationship was found between organic-matter content and CEC, suggesting continued addition of organic material will further approach the value of these parameters to those levels corresponding to natural soils under "Cerrado" vegetation.

Sidestream cigarette smoke effects on cardiovascular responses in conscious rats: involvement of oxidative stress in the fourth cerebral ventricle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Glibenclamide effects on renal function and histology after acute hemorrhage in rats under sevoflurane anesthesia

Introduction. Hypovolemia from hemorrhage evokes protective compensatory reactions, such as the renin-angiotensin system, which interferes in the clearance function and can lead to ischemia. This study was designed to evaluate the effects of glibenclamide, a K-ATP(+) channel blocker, on renal function and histology in rats in a state of hemorrhagic shock under sevoflurane anesthesia. Material and Methods. Twenty Wistar rats were randomized into two groups of 10 animals each (G1 and G2), only one of which (G2) received intravenous glibenclamide (1 mu g.g(-1)), 60 min before bleeding was begun. Both groups were anesthetized with sevoflurane and kept on spontaneous respiration with oxygen-air, while being bled of 30% of volemia in three stages with 10 min intervals. There was an evaluation of renal function-sodium para-aminohippurate and iothalamate clearances, filtration fraction, renal blood flow, renal vascular resistance-and renal histology. Renal function attributes were evaluated at three moments: M1 and M2, coinciding with the first and third stages of bleeding; and M3, 30 min after M2, when the animals were subjected to bilateral nephrectomy before being sacrificed. Results. Significant differences were found in para-aminohippurate clearance, G1 < G2, and higher renal vascular resistance values were observed in G1. Histological examination showed the greater vulnerability of kidneys exposed to sevoflurane alone (G1) with higher scores of vascular and tubular dilatation. There were vascular congestion and tubular vacuolization only in G1. Necrosis and signs of tubular regeneration did not differ in both groups. Conclusion. Treatment with glibenclamide attenuated acutely the renal histological changes after hemorrhage in rats under sevoflurane anesthesia.

Effects on mother and fetus of epidural and combined spinal-epidural techniques for labor analgesia

OBJETIVO: A peridural (AP) e a técnica de duplo bloqueio (DB) são utilizadas em analgesia para o trabalho de parto. Este estudo comparou os efeitos na mãe e no feto de ambas as técnicas em analgesia e anestesia para o parto. MÉTODOS: Quarenta parturientes ASA I e II receberam por via peridural 15 ml de ropivacaína a 0,125% (grupo AP) e 5 µg de sufentanil com 2,5 mg bupivacaína por via subaracnóidea (grupo DB). Foram avaliados: intensidade de dor, altura do bloqueio sensitivo, tempo de latência, bloqueio motor, duração da analgesia de parto, tempo para a resolução do parto, hipotensão materna e presença de prurido. Os recém-nascidos foram avaliados pelo índice de Apgar e escore da capacidade adaptativa e neurológica (ECAN), método de Amiel-Tison. RESULTADOS: Não houve diferenças significativas entre os grupos na intensidade da dor, no tempo de latência, no nível do bloqueio sensitivo e no índice de Apgar. O bloqueio motor, a duração da analgesia e o tempo para resolução do parto foram maiores no grupo DB, do qual sete parturientes apresentaram prurido leve. ECAN foi maior no grupo AP após meia hora, duas horas e 24 horas. Noventa e cinco por cento dos recém-nascidos do grupo AP e 60% do grupo DB foram considerados neurologicamente vigorosos ao exame de 24 horas. CONCLUSÃO: As duas técnicas mostraram-se eficazes para analgesia do trabalho de parto. As parturientes do grupo DB apresentaram prurido e trabalho de parto mais prolongado. Recém-nascidos de mães que receberam analgesia de parto via peridural apresentaram melhor ECAN.