Analysis on turning Ti-6Al-4V with different cooling methods

The aim of this paper is to optimize the machining of Ti-6Al-4V alloy, by studying the chip formation, roughness and tool wear for different cooling conditions. The results were compared between cooling methods, minimal quantity of fluid (MQF) and flooding, and also without fluid for the tool H13A. The turning of Ti-6Al-4V has shown good results on roughness (0, 8μm) and tool life, which was 11% lower with MQF than with the flooding method. The tool wear causes variation of the shear angle, which promotes strength hardening of the chip. As a result, the machined surface could be damaged. The use of the cutting fluid helps to save the cutting edge and could reduce the strength hardening. Nevertheless, it could also facilitate the formation of built-up edge. The nucleation of alpha lamellar colonies can occur due to a combination of deformation rates and temperature, mainly when the flooding is used, but it's not conclusive. The lamellar colonies were also found with the MQF in some regions, however, this structure did not show hardness variation compared to equiaxial. For all this reasons, the machining parameters might be carefully chosen.

Rough turning of titanium alloy (6Al-4V)

Metal machining is the complex process due the used cutting parameters. In metal cutting process, materials of workpiece differ widely in their ability to deform plastically, to fracture and to sustain tensile stresses. Moreover, the material involved in the process has a great influence in these operations. The Ti-6Al-4V alloy is very used in the aeronautical industry, mainly in the manufacture of engines, has very important properties such the mechanical and corrosion resistance in high te mperatures. The turning of the Ti-Al-4V alloy is very difficult due the rapid tool wear. Such behavior result of the its low thermal conductivity in addition the high reactivity with the cutting tool. The formed chip is segmented and regions of the large deformation named shear bands plows formed. The machinability of the cutting process can be evaluated by several measures including power consume, machined surface quality, tool wear, tool life, microstructure and morphology of the obtained chip. This paper studies the effect of cutting parameters, speed and feed rates, in the tool wear and chip properties using uncoating cemented carbide tool. Microe-structural characterization of the chip and tool wear was performed using scanning electron microscopy (SEM) and Light Optical Mcroscopy (LOM).

Effect of different methods of cutting fluid application on turning of a difficult-to-machine steel (SAE EV-8)

In this study, different methods of cutting fluid application are used in turning of a difficult-to-machine steel (SAE EV-8). Initially, a semisynthetic cutting fluid was applied using a conventional method (i.e. overhead flood cooling), minimum quantity of cutting fluid, and pulverization. A lubricant of vegetable oil (minimum quantity of lubricant) was also applied using the minimum quantity method. Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface, top surface of the chip (between workpiece and chip) and tool-workpiece contact. Moreover, two other methods were used: an interflow between conventional application and chip-tool interface jet (combined method) and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high-pressure system using a piston pump for generating a cutting fluid jet, a venturi for fluid application (minimum quantity of cutting fluid and minimum quantity of lubricant) and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. Among the results, it can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure, such as minimum quantity of volume and pulverization, when considering just the cutting tool wear. © 2013 IMechE.

Different methods of cutting fluid application on turning of a difficult-to-machine steel

Different methods of cutting fluid application are used on turning of a difficult-tomachine steel (SAE EV-8). A semi-synthetic cutting fluid was applied using a conventional method, minimum quantity of cutting fluid (MQCF), and pulverization. By the minimum quantity method was also applied a lubricant of vegetable oil (MQL). Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface; top surface of the chip; and tool-workpiece contact. Two other methods were used: an interflow between conventional application and chip-tool interface jet and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high pressure system using a piston pump for generating a cutting fluid jet, a Venturi for fluid application (MQCF and MQL), and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. It can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure. © (2013) Trans Tech Publications, Switzerland.

Experimental study of bottom feed updraft gasifier

The updraft biomass gasifiers currently available produce a gas with high tar content. For almost all downstream applications a substantial reduction of the tar concentration is required. The gravimetric tar concentration behavior in producer gas, obtained at a modified updraft fixed bed gasifier, was studied. The feedstock feeding system was modified respect to the traditional updraft gasification design in order to decrease the tar concentration in the producer gas; the material is feeding continuously through a conduit in the base of the reactor over the grate. The caloric power of the syngas obtained was slightly lower than the typical value for this type of reactor and the highest efficiency obtained for the woodchip gasification was 77%. The highest tar concentration obtained during the experiments was 1652.7 mg N m-3 during the first our of experiments, comparable with the smaller value reported for the updraft reactors, this value is reduced significantly after the stabilization of the gasification process in the reactor. The smaller value obtained was 21 mg N m-3. © 2013 Elsevier Ltd.

Approximation of hyperbolic tangent activation function using hybrid methods

Artificial Neural Networks are widely used in various applications in engineering, as such solutions of nonlinear problems. The implementation of this technique in reconfigurable devices is a great challenge to researchers by several factors, such as floating point precision, nonlinear activation function, performance and area used in FPGA. The contribution of this work is the approximation of a nonlinear function used in ANN, the popular hyperbolic tangent activation function. The system architecture is composed of several scenarios that provide a tradeoff of performance, precision and area used in FPGA. The results are compared in different scenarios and with current literature on error analysis, area and system performance. © 2013 IEEE.

TAB2VHDL: um ambiente de síntese lógica para máquinas de estados finitos

Pós-graduação em Engenharia Elétrica - FEIS

Técnicas de paralelização em GPGPU aplicadas em algoritmo para remoção de ruído multiplicativo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Qualidade de cavacos produzidos em sistemas florestais de curta rotação de eucalipto para fins energéticos

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Estudo acústico da pronúncia de pares mínimos vocálicos do inglês por falantes nativos, professores brasileiros e alunos de nível intermediário e avançado

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Identificação de perfis diferenciais de metilação do DNA na endometriose

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Identificação de assinaturas de seleção e anotação do genoma em bovinos da raça Nelore

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo da formação do cavaco no torneamento de superligas de níquel

Pós-graduação em Engenharia Mecânica - FEG

A influência da aplicação de fluído de corte no torneamento da liga de aluminio AA 7075

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A valiação da integridade superficial e usinabilidade de engrenagens forjadas utilizando fresamento com alta velocidade de corte

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)