Europium(III) Concentration Effect on the Spectroscopic and Photoluminescent Properties of BaMoO4:Eu

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Photoluminescence behavior in MgTiO3 powders with vacancy/distorted clusters and octahedral tilting

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evolution of photoluminescence as a function of the structural order or disorder in CaMoO4 nanopowders

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Structural transition on Pb1-xSrxTiO3 produced by chemical method

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The effect of polymerization cycles on porosity of microwave-processed denture base resin

Statement of problem. Although most of the physical properties of denture base resin polymerized by microwave energy have been shown to be similar to resins polymerized by the conventional heat polymerization method, the presence of porosity is a problem.Purpose. This study evaluated the effect of different microwave polymerization cycles on the porosity of a denture base resin designed for microwave polymerization.Material and methods. Thirty-two rectangular resin specimens (65 X 40 X 5 mm) were divided into 3 experimental groups (A, B, and C; Onda-Cryl, microwave-polymerized resin) and I control group (T; Classico, heat-polymerized resin), according to the following polymerization cycles: (A) 500 W for 3 minutes, (B) 90 W for 13 minutes + 500 W for 90 seconds, (C) 320 W for 3 minutes + 0 W for 4 minutes + 720 W for 3 minutes, and (T) 74degreesC for 9 hours. Porosity was calculated by measurement of the specimen volume before and after its immersion in water. Data were analyzed using 1-way analysis of variance (alpha = .05).Results. The mean values and SDs of the percent mean porosity were: A = 1.05% +/- 0.28%, B = 0.91% +/- 0.15%, C = 0.88% +/- 0.23%, T = 0.93% +/- 0.23%. No significant differences were found in mean porosity among the groups evaluated.Conclusion. Within the limitations of this study, a denture base resin specifically designed for microwave Polymerization tested was not affected by different polymerization cycles. Porosity was similar to the conventional heat-polymerized denture base resin tested.

Studies on the formation of complex coacervates between chitosan and alginate during microparticles preparation

The formation of complex coacervates between chitosan and alginate was evaluated during microparticles formation. Mass ratio between polyelectrolytes and calcium chloride concentration were determinated by conductimetric analysis and by calcium ions quantification, respectively. Inert microparticles were prepared using a complex coacervation method in W/O emulsion and morphological analyses of microparticles were carried out. This method enabled the production of spherical particles, with slightly rough surface and narrow size distribution with maximal diameter of 10 μm.

Effect of polymerization methods and thermal cycling on color stability of acrylic resin denture teeth

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dispositivos flexíveis de monitoramento de pH e de deflexão mecânica à base de polianilina

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Microspheres of alginate-chitosan containing isoniazid

Isoniazid was encapsulated into microspheres of alginate-chitosan by means of a complex coacervation method in an emulsion system. Since the encapsulation of isoniazid tends to be limited by its hydrophilic characteristics, this study proposes its microencapsulation by adsorption. The particles were prepared in three steps: (1) preparation of a W/O emulsion; (2) phase separation; and (3) adsorption of the drug. The isolated particles were placed in a solution of the drug under stirring to allow adsorption. The morphology and particle size were analysed by scanning electron microscopy (SEM). The isoniazid content was determined by extraction in 1 m phosphate buffer pH 7.5 under stirring for 4 h. Finally, the samples were filtered and analysed in an UV/VIS spectrophotometer at 260 nm. In vitro release tests were carried out in 0.05 m phosphate buffer pH 7.5. The results showed that microspheres of alginate-chitosan obtained were of spherical shape. The emulsion used for microparticle formation allows the preparation of particles with a narrow size distribution. The adsorption observed is probably of chemical nature, i.e. there is an ionic interaction between the drug and the surface of the particles.

Laserlike emission from silica inverse opals infiltrated with rhodamine 6G

Monodisperse latex spheres were obtained by a surfactant free styrene polymerization method and used to obtain colloidal crystals by controlled centrifugation settling. Silica inverse opals were then prepared by using the colloidal crystals as templates and TEOS/ethanol solution. The inverse opals were infiltrated with Rhodamine 6G and laserlike emission was observed at 590 nm under 532 nm pump wavelength. The data show line narrowing of the dye fluorescence and a laser threshold of similar to 0.1 mJ/pulse. Local-field effects and light scattering due to structural defects are the main mechanisms contributing to generation of the laser-action observed. (c) 2005 Elsevier B.V. All rights reserved.

Resin-based composite reinforced sealant

Purpose: To describe and picture a technique for using a resin-bonded sealant reinforced by inclusion of resin-based composite, before polymerization. Method: Using an extracted mandibular molar, embedded in plaster and isolated with a rubber dam, a step-by-step depiction of the technique is shown. Results: A picture of a six-year-old sealant in a first permanent molar, still in perfect condition, is shown. Conclusion: This technique offers a reliable method for treating pits and fissures.

Increasing the dielectric breakdown strength of poly(ethylene terephthalate) films using a coated polyaniline layer

The dielectric strength of films made from poly(ethylene terephthalate) (PET) coated with a thin layer of polyaniline (PANI) was studied. The PANI layer was deposited on the PET films by the 'in situ' chemical polymerization method. The PANI layer of the PANI/PET films was undoped in NH4OH 0.1 M solution and re-doped with aqueous HCl solution under different pH values varying from 1 to 10. Electric breakdown measurements were performed by applying a voltage ramp and the results showed a dependence of the dielectric strength on the pH of the doping solution due to the changes in the electrical conductivity of the PANI layer. The dielectric strength of PET/PANI films treated under higher pH conditions showed an electric strength about 30% larger than the PET films, since it leads to a non-conductive PANI layer.

Application of Polysaccharide Hydrogels in Adsorption and Controlled-Extended Release of Fertilizers Processes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Pesquisa e desenvolvimento de microesferas de poli(vinil álcool) com alta cristalinidade para utilização em embolização e quimioembolização

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sistema multiparticulado magnético: desenvolvimento e avaliação In Vivo através da biossusceptometria AC

Pós-graduação em Ciências Farmacêuticas - FCFAR