Experimental analysis of heat recoveries with heat pipes operating in low inclination angle

Heat recovery devices are important in the optimization of thermal systems, since they can be used to reduce thermal losses to the environment. The use of heat pipes in these types of equipment can provide heat recoveries of higher efficiency, since both fluid flows are external and there are less contamination risks between the hot and cold fluids. The objective of this work is to study a heat recovery unit constructed with heat pipes and mainly, to analyze the influence of the inclination of the heat pipes on the performance of the equipment. For this analysis, a heat recovery unit was constructed which possesses 48 finned heat pipes in triangular geometry, the evaporator and condenser being of the same length. This unit was tested in an air-air system simulating a heat recovery process in which heat was supplied to the hot fluid by electrical resistances. The results have shown that there exists an inclination at which the system has a better performance, but for higher inclinations there is no significant increase of the efficiency of the system. This paper also presents the influence of inclination of heat pipes on effectiveness and NTU parameters which are important in heat exchanger design.

Modeling of pre-regulator boost ZCS interleaved operating in critical conduction mode and with high power factor

This paper presents a new pre-regulator boost operating in the boundary area between the continuous and discontinuous conduction modes of the boost inductor current, where the switches and boost diode performing zero-current commutations during its turn-off, eliminating the disadvantages related to the reverse recovery losses and electromagnetic interference problems of the boost diode when operating in the continuous conduction mode. Additionally, the interleaving technique is applied in the power cell, providing a significant input current ripple reduction. It should be noticed that the main objective of this paper is to present a complete modeling for the converter operating in the critical conduction mode, allowing an improved design procedure for interleaved techniques with high input power factor, a complete dynamic analysis of the structure, and the possibility of implementing digital control techniques in closed loop.

Profitability measures of dairy cows

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

HPF boost interleaved operating in discontinuous conduction mode for trolleybus application

This paper deals with results of a research and development (R&D) project in cooperation with Electric Power Distribution Company in São Paulo (Brazil) regarding the development and experimental analysis of a new concept of power drive system suitable for application in traction systems of electrical vehicles pulled by electrical motors, which can be powered by urban DC or AC distribution networks. The proposed front-end structure is composed by five boost power cells in interleaving connection, operating in discontinuous conduction mode as AC-DC converter, or as DC-DC converter, in order to provide the proper DC output voltage range required by DC or AC adjustable speed drivers. Therefore, when supplied by single-phase AC distribution networks, and operating as AC-DC converter, it is capable to provide high power factor, reduced harmonic distortion in the input current, complying with the restrictions imposed by the IEC 61000-3-4 standards resulting in significant improvements for the trolleybuses systems efficiency and for the urban distribution network costs. Considering the compliance with input current restrictions imposed by IEC 61000-3-4 standards, two digital control strategies were evaluated. The digital controller has been implemented using a low cost FPGA (XC3S200) and developed totally using a hardware description language VHDL and fixed point arithmetic. Experimental results from a 15 kW low power scale prototype operating in DC and AC conditions are presented, in order to verify the feasibility and performance of the proposed system. © 2009 IEEE.

Custos e rentabilidade do milho em função do manejo do solo e da adubação nitrogenada

Agronomic practices that help farmers to raise yield and reduce costs must be studied to ensure agricultural sustainability. Thus, the objective of this study was to analyze economically the effect of soil management and nitrogen fertilization in maize crops. Treatments consisted of a combination of 3 soil management techniques (plow harrows + floating harrows, chisel + floating harrows, and no-tillage), 5 periods of nitrogen fertilization (control - 0 kg ha -1 N; 120 kg ha -1 after sowing (S); 120 kg ha -1 in the V 6 stage; 30 kg ha -1 (S) + 90 kg ha -1 in V 6; 30 kg ha -1 (S) + 45 kg ha -1 in V 4 + 45 kg ha -1 in V 8 The total operating cost (TOC), gross revenue (GR), operating profit (OP), profitability index (PI), break-even yield, and break-even price were estimated. It was concluded that the no-tillage system, after 11 years of management, associated with nitrogen fertilization promotes positive PI and OP, being useful to farmers.

On a control design to an AFM microcantilever beam, operating in a tapping-mode, with irregular behavior

In last decades, control of nonlinear dynamic systems became an important and interesting problem studied by many authors, what results the appearance of lots of works about this subject in the scientific literature. In this paper, an Atomic Force Microscope micro cantilever operating in tapping mode was modeled, and its behavior was studied using bifurcation diagrams, phase portraits, time history, Poincare maps and Lyapunov exponents. Chaos was detected in an interval of time; those phenomena undermine the achievement of accurate images by the sample surface. In the mathematical model, periodic and chaotic motion was obtained by changing parameters. To control the chaotic behavior of the system were implemented two control techniques. The SDRE control (State Dependent Riccati Equation) and Time-delayed feedback control. Simulation results show the feasibility of the bothmethods, for chaos control of an AFM system. Copyright © 2011 by ASME.

Análises técnicas e econômicas no sistema de integração lavoura-pecuária submetido à adubação nitrogenada

Sustainable agriculture, reduced production costs and adding value to the system are achieved through the use of agricultural areas throughout the year, in integrated or mixed system. The study aimed to determine the technical coefficients to estimate and evaluate the operational cost and profitability indicators of the consortium of corn with two species of Brachiaria (B. brizantha, MG-5 and B. ruziziensis). The crops were submitted to N rates (0, 100, 200, 300 e 400kg ha-1year-1) at sidedressing, using urea, and winter common bean in succession, in crop-livestock integration under no-tillage, in irrigated conditions, in 2008/2009 agricultural year in Cerrado region (Selvíria - MS). The experiment was conducted in a randomized complete block design with four replications in a 2 x 5factorial. It was concluded thatcathe inputs were the components that most increased the producing cost of corn and common bean in the ILP study. The total operational cost has increased as a function of increasing doses of N. In all treatments the levels of profitability were positive indicating the viability of the system. The treatment that showed the best technical and economic performance was intercropped with corn and B. brizantha, fertilized with 100kg ha-1year-1N and common bean in succession.

Efficiency analysis of an isolated high voltage gain converter operating in resonant and non-resonant mode

This paper presents an efficiency investigation of an isolated high step-up ratio dc-dc converter aimed to be used for energy processing from low-voltage high-current energy sources, like batteries, photovoltaic modules or fuel-cells. The considered converter consists of an interleaved active clamp flyback topology combined with a voltage multiplier at the transformer secondary side capable of two different operating modes, i.e. resonant and non-resonant according to the design of the output capacitors. The main goal of this paper is to compare these two operating modes from the component losses point of view with the aim of maximize the overall converter efficiency. The approach is based on losses prediction using steady-state theoretical models (designed in Mathcad environment), taking into account both conduction and switching losses. The models are compared with steady-state simulations and experimental results considering different operating modes to validate the approach. © 2012 IEEE.

Custos e viabilidade econômica da produção de casulos do bicho-da-seda

Sericiculture is characterized by the possibility of income generation in areas smaller than 10.0 ha and by the rationalization of family labor. Even considering this favorable scenario for the development of this activity, there is still a gap in the management of its economic factors in most of the rural properties within this chain, contributing negatively to their expansion. This study aimed at assessing the production cost and economic viability for producing silkworm cocoons, by using a case study conducted in a property located in Quatá, São Paulo State, Brazil. The main results for a production of 1,904 kg-1 of silkworm cocoons, with labor costs reaching 51.5% of the Effective Operating Cost and 35.5% of the Total Operating Cost, were a profitability index higher than 50% and an Internal Rate of Return of 9.68%, for the second production year, providing a good profitability rate for this agricultural segment, when we consider that the improved profitability of the producer is proportional to the best production indicators, particularly due to the fast return that this activity provides.

Energetic, ecologic and fluid-dynamic analysis of a fluidized bed gasifier operating with sugar cane bagasse

This work aims to study the thermodynamic, ecological and fluid-dynamic aspects of a circulating fluidized bed gasifier using sugar cane bagasse as biomass, in order to estimate a model of its normal operation. In the initial stage was analysed the composition of biomass selected (sugar cane bagasse) and its lower heating value (LHV) was calculated. The energy balance of the gasifier was done, being the volumetric flow of air, synthesis gas and biomass estimated. Also the power produced by this gasifier was theoretically estimated. Then the circulating fluidized bed gasifier was designed for operation with approximately 100 kg/h of processed biomass. Cross-sectional area of the reactor, feeder size, diameter of the exit zone of the gases and minimum height of the expanded bed were selected. Some bed gasifier hydrodynamic factors were also studied. The minimum fluidization velocity, fluidization terminal velocity, and average fluidizing velocity were calculated, in order to understand the fluid-dynamic behaviour of gasification of this fuel. It was obtained a theoretical model that can support a possible prototype of circulating fluidized bed gasifier biomass. Finally, there were studied the ecological aspects of the gasifier, through an overall methodology. Ecological efficiencies were estimated for two scenarios: first considering the carbon cycle and thereafter disregarding the carbon cycle. In both cases, it can be proved the ecological viability of the project. © 2013 Elsevier Ltd. All rights reserved.

Eficiência econômica e energética do bicultivo de peixes na região do Médio Paranapanema, Estado de São Paulo: Fernanda de Paiva Badiz Furlaneto. -

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Avaliação da produção de uvas finas para mesa na região noroeste do Estado de São Paulo: questões técnicas, ambientais e econômicas

Pós-graduação em Agronomia - FEIS

Adubação nitrogenada no consórcio alface e rúcula

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Consórcios de pepino e alface em cultivo protegido: viabilidade agroeconômica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Using a threaded framework to enable practical activities in Operating Systems courses

Teaching Operating Systems (OS) is a rather hard task, since being an OS designer is not a desired goal for most students and the subject demands a large amount of knowledge over system's details. To reduce the difficulty many courses are planned with laboratory practices, differing in how the practices are designed. Some try to implement next-to-real kernels, others use simulators, and even others use synthetic kernels. In this paper an approach based on synthetic kernels is described. It uses thread programming in order to establish control over the operating system components. T his approach allows the kernel to grow following the materials presented in the course. It has been successfully applied in two different courses at our University, the first one being a basic OS course and the second one an upper level course. Results from these applications are presented.