Regional hydroclimatic variability and Brazil's 2001 energy crisis

Purpose - This paper seeks to address the issue of persistent and widespread drought conditions during 2000 and 2001, which were the apparent cause of the decline of water levels in the reservoirs of Brazilian hydroelectric power plants. Design/methodology/approach - This issue is addressed here through a case study of the hydroclimatology of the Paraíba river basin, in Southeast Brazil, home to four large multi-purpose operational reservoirs. Findings - The data analysis shows that neither changes in the frequency nor magnitude of extreme hydrological events (droughts and floods) nor in annual rainfall amounts can be detected from the existing climate record. The explanation is consistent with the fact that the terrestrial water and energy cycles are tightly, and non-linearly, coupled through evapotranspiration. Research limitations/implications - Therefore small change in the seasonality of rainfall can have a significant impact on the basin's overall hydrologic regime, and thus on the availability of water resources. Originality/value - Often, adaptation and resilience to climate variability are discussed in the context of catastrophic events such as floods and droughts. This study suggests that a different type of impacts, those associated with subtle, yet persistent changes of seasonality in the terrestrial water cycle, cannot be ignored in studies of long-term sustainability of water resources. © Emerald Group Publishing Limited.

Evaluation of the performance of α-SiAlON tool when turning Ti-6Al-4V alloy without coolant

Due to their high hardness and wear resistance, Si3N4 based ceramics are one of the most suitable cutting tool materials for machining cast iron, nickel alloys and hardened steels. However, their high degree of brittleness usually leads to inconsistent results and sudden catastrophic failures. This necessitates a process optimization when machining superalloys with Si3N4 based ceramic cutting tools. The tools are expected to withstand the heat and pressure developed when machining at higher cutting conditions because of their high hardness and melting point. This paper evaluates the performance of α-SiAlON tool in turning Ti-6Al-4V alloy at high cutting conditions, up to 250 m min-1, without coolant. Tool wear, failure modes and temperature were monitored to access the performance of the cutting tool. Test results showed that the performance of α-SiAl0N tool, in terms of tool life, at the cutting conditions investigated is relatively poor due probably to rapid notching and excessive chipping of the cutting edge. These facts are associated with adhesion and diffusion wear rate that tends to weaken the bond strength of the cutting tool.

Turning of compacted graphite iron using commercial tiN coated Si 3N4 under dry machining conditions

Due to their high hardness and wear resistance Si3N4 based ceramics are one of the most suitable cutting tool materials for machining hardened materials. Therefore, their high degree of brittleness usually leads to inconsistent results and sudden catastrophic failures. Improvement of the functional properties these tools and reduction of the ecological threats may be accomplished by employing the technology of putting down hard coatings on tools in the state-of-the-art PVD processes, mostly by improvement of the tribological contact conditions in the cutting zone and by eliminating the cutting fluids. However in this paper was used a Si3N4 based cutting tool commercial with a layer TiN coating. In this investigation, the performance of TiN coating was assessed on turning used to machine an automotive grade compacted graphite iron. As part of the study were used to characterise the performance of cutting tool, flank wear, temperature and roughness. The results showed that the layer TiN coating failed to dry compacted graphite iron under aggressive machining conditions. However, using the measurement of flank wear technique, the average tool life of was increased by VC=160 m/min.The latter was also observed using a toolmakers microscope and scanning electron microscopy (SEM).

Avaliação crítica da legislação brasileira de sucos de fruta, com ênfase no suco de fruta pronto para beber

The aim of this work was to critically assess the Brazilian regulations on fruit juices, with emphasis on ready-to-drink fruit juice. According to the Brazilian regulations, bottled fruit juices must follow specific regulations. They should be in accordance with the definition and designation that identify them, with the quality parameters established, and especially, follow the Brazilian food labeling regulations. The Brazilian regulations on bottled fruit juices have some gaps that promote their misunderstanding and marketing of substandard juices. Frequent changes, divergent labeling regulations and inappropriate use of expressions on the label can also lead to misinterpretation. Food regulations need to be clear and updated frequently if they are to be known and followed. Additionally, their wide dissemination should contribute to informed choices when buying.

Fracture resistance of bovine incisors restored with different glass fiber posts: Effect of the diameter of fiber post

Aim: Compare the effect of three post designs on the fracture resistance and failure modes of composite core-fiber post-crownless tooth sets. Materials and Methods: Ninety bovine incisors were selected and divided into nine groups of 10 specimens. The teeth were assigned to three groups based on the post design: Cylindrical, tapered, and double-tapered. Each group was subdivided into three subgroups in accordance with the diameter of the post: Small (No.1), medium (No.2), and large (No.3). The Panavia F system was used for post cementation. The specimens were mounted in acrylic resin blocks with a layer of silicone rubber covering the roots. A universal testing machine compressively loaded the specimens from the palatal side at a crosshead speed of 1 mm/min and at an angle of 135I to the long axis of the teeth, until failure occurred. The failure mode was determined by a stereomicroscope inspection of all the specimens. Data were analyzed by one-way ANOVA and the Tukey test (P < 0.05). Results: The fracture resistance was affected by the type of post (P < 0.0001). A narrower diameter for all of the post systems allowed for higher resistance. The main failure mode in the large cylindrical group was catastrophic fractures, while the main failures in the other eight groups were favorable. Conclusion: Narrower diameter posts showed higher fracture resistance. The dominant failure pattern was repairable fracture, except for those with large cylindrical groups.

Influence of convergence angle of tooth preparation on the fracture resistance of Y-TZP-based all-ceramic restorations

Objective: To investigate the influence of the convergence angle of tooth preparation on the fracture load of Y-TZP-based ceramic (YZ-Vita YZ) substructure (SB) veneered with a feldspathic porcelain (VM9-Vita VM9). Methods: Finite element stress analysis (FEA) was performed to examine the stress distribution of the system. Eighty YZ SB were fabricated using a CAD-CAM system and divided into four groups (n = 20), according to the total occlusal convergence (TOC) angle: G6-6° TOC; G12-12° TOC; G20-20° TOC; and G20MOD-20° TOC with modified SB. All SB were veneered with VM9, cemented in a fiber reinforced epoxy resin die, and loaded to failure. Half of the specimens from each group (n = 10) were cyclic fatigued (106 cycles) before testing. Failure analysis was performed to determine the fracture origin. Data were statistically analyzed using Anova and Tukey's tests (α = 0.05). Results: The greatest mean load to fracture value was found for the G20MOD, which was predicted by the FEA. Cyclic fatigue did not significantly affect the load of fracture. Catastrophic failure originating from the internal occlusal surface of the SB was the predominant failure mode, except for G20MOD. Significance: The YZ-VM9 restorations resisted greater compression load than the usual physiological occlusal load, regardless of the TOC angle of preparations. Yet, the G20MOD design produced the best performance among the experimental conditions evaluated. © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Dynamics and coexistence in a system with intraguild mutualism

It is a tenet of ecological theory that two competing consumers cannot stably coexist on a single limiting resource in a homogeneous environment. Many mechanisms and processes have since been evoked and studied, empirically and theoretically, to explain species coexistence and the observed biological diversity. Facilitative interactions clearly have the potential to enhance coexistence. Yet, even though mutual facilitation between species of the same guild is widely documented empirically, the subject has received very little theoretical attention. Here, we study one form of intraguild mutualism in the simplest possibly community module of one resource and two consumers. We incorporate mutualism as enhanced consumption in the presence of the other consumers. We find that intraguild mutualism can (a) significantly enhance coexistence of consumers, (b) induce cyclic dynamics, and (c) give rise to a bi-stability (a 'joint' Allee effect) and potentially catastrophic collapse of both consumer species. © 2012 Elsevier B.V.

Ocorrência de eventos climáticos extremos e sua repercurssão sócio-ambiental no litoral norte paulista

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A temática ambiental e o ensino de física na escola média: a produção de energia elétrica em larga escala como um tema controverso

Pós-graduação em Educação Escolar - FCLAR

Proposta de um procedimento metodológico para o estudo de problemas geoambientais com base em banco de dados de eventos atmosféricos severos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Gestão ambiental: um estudo referenciado na A3P em uma secretaria do município de Bauru - SP

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência de ciclos térmicos na microestrutura e propriedades mecânicas da junta soldada do aço COS CIVIL 300

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise microestrutural de revestimentos usados no reparo de turbinas hidráulicas danificadas pela cavitação

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Alterações climáticas e a percepção dos munícipes de Rio Claro - SP

Pós-graduação em Geografia - IGCE

Disponibilidade de minerais, germinação e vigor de sementes de milho

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)