Optimal design of smart structures using bonded plezoelectrics for vibration control

Smart material technology has become an area of increasing interest for the development of lighter and stronger structures which are able to incorporate actuator and sensor capabilities for collocated control. In the design of actively controlled structures, the determination of the actuator locations and the controller gains, is a very important issue. For that purpose, smart material modelling, modal analysis methods, control and optimization techniques are the most important ingredients to be taken into account. The optimization problem to be solved in this context presents two interdependent aspects. The first one is related to the discrete optimal actuator location selection problem which is solved in this paper using genetic algorithms. The second is represented by a continuous variable optimization problem, through which the control gains are determined using classical techniques. A cantilever Euler-Bernoulli beam is used to illustrate the presented methodology.

Optimal placement of piezoelectric sensor/actuators for smart structures vibration control

Smart material technology has become an area of increasing interest for the development of lighter and stronger structures that are able to incorporate actuator and sensor capabilities for collocated control. In the design of actively controlled structures, the determination of the actuator locations and the controller gains is a very important issue. For that purpose, smart material modeling, modal analysis methods, and control and optimization techniques are the most important ingredients to be taken into account. The optimization problem to be solved in this context presents two interdependent aspects. The first is related to the discrete optimal actuator location selection problem, which is solved in this paper using genetic algorithms. The second is represented by a continuous variable optimization problem, through which the control gains are determined using classical techniques. A cantilever Euler-Bernoulli beam is used to illustrate the presented methodology.

System identification and active vibration control of a flexible structure

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Vibration energy harvesting using piezoelectric transducer and non-controlled rectifiers circuits

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

In situ evaluation of the remineralizing capacity of pit and fissure sealants containing amorphous calcium phosphate and/or fluoride

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of Stress Patterns Produced by Implant-Retained Overdentures and Implant-Retained Fixed Partial Denture

The purposes of this study were to photoelastically measure the biomechanical behavior of 4 implants retaining different cantilevered bar mandibular overdenture designs and to compare a fixed partial denture (FPD). A photoelastic model of a human edentulous mandible was fabricated, which contained 4 screw-type implants (3.75 x 10 mm) embedded in the parasymphyseal area. An FPD and 3 overdenture designs with the following attachments were evaluated: 3 plastic Hader clips, 1 Hader clip with 2 posterior resilient cap attachments, and 3 ball/O-ring attachments. Vertical occlusal forces of 100 N were applied between the central incisor and unilaterally to the right and left second premolars and second molars. Stresses that developed in the supporting structure were monitored photoelastically and recorded photographically. The results showed that the anterior loading, the overdenture with 3 plastic Hader clips, displayed the largest stress concentration at the medium implant. With premolar loading, the FPD and overdenture with 3 plastic Hader clips displayed the highest stresses to the ipsilateral terminal implant. With molar loading, the overdenture with 3 ball/O-ring attachments displayed the most uniform stress distribution in the posterior edentulous ridge, with less overloading in the terminal implant. It was concluded that vertical forces applied to the bar-clip overdenture and FPD created immediate stress patterns of greater magnitude and concentration on the ipsilateral implants, whereas the ball/O-ring attachments transferred minimal stress to the implants. The increased cantilever in the FPD caused the highest stresses to the terminal implant.

Analysis of mechanical behavior of implant-supported prostheses in the anterior maxilla: analysis by speckle pattern interferometry

The use of implants to rehabilitation of total edentulous, partial edentulous or single tooth is increasing, it is due to the high rate of success that this type of treatment present. The objective of this study was to analyze the mechanical behavior of different positions of two dental implants in a rehabilitation of 4 teeth in the region of maxilla anterior. The groups studied were divided according the positioning of the implants. The Group 1: Internal Hexagonal implant in position of lateral incisors and pontic in region of central incisors; Group 2: Internal Hexagonal implant in position of central incisors and cantilever of the lateral incisors and Group3 - : Internal Hexagonal implants alternate with suspended elements. The Electronic Speckle Pattern Interferometry (ESPI) technique was selected for the mechanical evaluation of the 3 groups performance. The results are shown in interferometric phase maps representing the displacement field of the prosthetic structure.

Suppressing grazing chaos in impacting system by structural nonlinearity

In this note we investigate the influence of structural nonlinearity of a simple cantilever beam impacting system on its dynamic responses close to grazing incidence by a means of numerical simulation. To obtain a clear picture of this effect we considered two systems exhibiting impacting motion, where the primary stiffness is either linear (piecewise linear system) or nonlinear (piecewise nonlinear system). Two systems were studied by constructing bifurcation diagrams, basins of attractions, Lyapunov exponents and parameter plots. In our analysis we focused on the grazing transitions from no impact to impact motion. We observed that the dynamic responses of these two similar systems are qualitatively different around the grazing transitions. For the piecewise linear system, we identified on the parameter space a considerable region with chaotic behaviour, while for the piecewise nonlinear system we found just periodic attractors. We postulate that the structural nonlinearity of the cantilever impacting beam suppresses chaos near grazing. (C) 2007 Elsevier Ltd. All rights reserved.

Phase-Locked loops lock-in range in Frequency Modulated-Atomic Force Microscope nonlinear control system

Since the mid 1980s the Atomic Force Microscope is one the most powerful tools to perform surface investigation, and since 1995 Non-Contact AFM achieved true atomic resolution. The Frequency-Modulated Atomic Force Microscope (FM-AFM) operates in the dynamic mode, which means that the control system of the FM-AFM must force the micro-cantilever to oscillate with constant amplitude and frequency. However, tip-sample interaction forces cause modulations in the microcantilever motion. A Phase-Locked loop (PLL) is used to demodulate the tip-sample interaction forces from the microcantilever motion. The demodulated signal is used as the feedback signal to the control system, and to generate both topographic and dissipation images. As a consequence, a proper design of the PLL is vital to the FM-AFM performance. In this work, using bifurcation analysis, the lock-in range of the PLL is determined as a function of the frequency shift (Q) of the microcantilever and of the other design parameters, providing a technique to properly design the PLL in the FM-AFM system. (C) 2011 Elsevier B.V. All rights reserved.

Comments on nonlinear dynamics of a non-ideal Duffing-Rayleigh oscillator: Numerical and analytical approaches

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Phase-Locked Loop design applied to frequency-modulated atomic force microscope

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Energia de superfície para nanossuperfícies de TiO2 na direção (001)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Salting kinetics and salt diffusivities in farmed Pantanal caiman muscle

A criação de jacaré do Pantanal (Caiman crocodilus yacare) em cativeiro tem sido estimulada, e entre as técnicas de processamento de sua carne, a salga é um processo de conservação relativamente simples e de baixo custo. O objetivo deste trabalho foi estudar a cinética de difusão de cloreto de sódio em carne de jacaré do Pantanal criado em cativeiro, durante a salga úmida. Foram utilizados volumes limitados de salmoura e os experimentos foram realizados com relações salmoura/músculo de 3, 4 e 5, com concentrações de salmoura de 15%, 20% e 25% em peso e temperaturas de 10, 15 e 20ºC. A solução analítica da segunda lei de Fick, considerando difusão unidimensional em uma placa infinita em contato com uma solução bem agitada de volume limitado, foi utilizada para calcular os coeficientes de difusão efetivos de sal e estimar o conteúdo de cloreto de sódio nos filés. Obteve-se boa concordância entre o modelo analítico considerado e os dados experimentais. As difusividades do sal nos filés ocorreram na faixa de 0,47x10-10 a 9,62x10-10 m²/s.

Propriedades eletrônicas e estruturais do PbTiO3: teoria do funcional de densidade aplicada a modelos periódicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

AN IMPROVED ELECTROPHORETIC METHOD FOR THE DETERMINATION OF SERUM MILK PROTEIN VARIANTS IN GYR-HOLSTEIN COWS

Milk serum proteins such as alpha-lactalbumin (ALA) and beta-lactoglobulin (BLG) present biochemical polymorphism which is under the control of codominant autosomal alleles. In the present report, we propose modifications of traditional electrophoretic techniques such as increasing the running gel concentration from 5 to 10% and the addition of 5 M urea to the stacking gel, which permitted the detection of two variants (A and B) at the ALA and BLG loci. About 8 mul of milk serum (6 mg/ml protein) and 10 pl of total fresh milk were applied. Bovine serum albumin (BSA) and immunolactoglobulins (ILG) could also be discriminated. Total fresh milk was as useful as the purified serum milk proteins for the discrimination of ALA and BLG serum milk protein polymorphism by alkaline vertical slab polyacrylamide gel electrophoresis. However, BSA and ILG ran with caseins, which prevented their characterization in this system.