Ferroelectric and dielectric properties of Ba0.5Sr0.5(Ti0.80Sn0.20)O-3 thin films grown by the soft chemical method

Polycrystalline Ba0.5Sr0.5(Ti0.80Sn0.20)O-3 (BST:Sn) thin films with a perovskite structure were prepared by the soft chemical method on a platinum-coated silicon substrate from spin-coating technique. The resulting thin films showed a dense structure with uniform grain size distribution. The dielectric constant of the films estimated from C-V curve is around 1134 and can be ascribed to a reduction in the oxygen vacancy concentration. The ferroelectric nature of the film indicated by butterfly-shaped C-V curves and confirmed by the hysteresis curve, showed remnant polarization of 14 mu C/cm(2) and coercive field of 74 kV/cm at frequency of 1 MHz. At the same frequency, the leakage current density at 1.0 V is equal to 1.5 x 10(-7) A/cm(2). This work clearly reveals the highly promising potential of BST:Sn for application in memory devices. (c) 2006 Elsevier B.V. All rights reserved.

Microwave-hydrothermal synthesis of barium strontium titanate nanoparticles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Restriction fragment analysis of the ribosomal DNA of Paratelmatobius and Scythrophrys species (Anura, Leptodactylidae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Study of the dielectric and ferroelectric properties of chemically processed BaxSr1-xTiO3 thin films

Polycrystalline BaxSr1-xTiO3 (x = 0.4 and 0.8) thin films with a perovskite structure were prepared by the polymeric precursor method on a platinum-coated silicon substrate. High-quality thin films with uniform composition and thickness were successfully produced by dip-coating and spin-coating techniques. The resulting thin films prepared by dip and spin-coating showed a well-developed dense polycrystalline structure with uniform grain size distribution. The metal-BST-metal structure of the thin films displays good dielectric and ferroelectric properties. The ferroelectric nature to BaxSr1-xTiO3 (x = 0.8) thin film, indicated by butterfly-shaped C-V curves and confirmed by the hysteresis curve, showed 2P(r) = 5.0 muC/cm(2) and E-c = 20 kV/cm. The capacitance-frequency curve reveals that the dielectric constant may reach a value of up to 794 at 1 kHz. on the other hand, the BaxSr1-xTiO3 (x = 0.4) thin films had paraelectric nature and dielectric constant and the dissipation factor at a frequency of 100 kHz were 680 and 0.01, respectively, for film annealed at 700 degreesC. In addition, an examination of the film's I-V curve at room temperature revealed the presence of two conduction regions in the BaxSr1-xTiO3 (x = 0.4 and 0.8) thin films, showing ohmic-like behavior at low voltage and a Schottky-emission or Poole-Frenkel mechanism at high voltage. (C) 2001 Elsevier B.V. B.V. All rights reserved.

Photoluminescence at room temperature in disordered Ba(0.50)Sr(0.)5(0)(Ti0.80Sn0.20)O-3 thin films

Photoluminescence (PL) properties at room temperature of disordered Ba0.50Sr0.50(Ti0.80Sn0.20)O-3 (BST:Sn) thin films were obtained by the polymeric precursor method. X-ray diffraction data and corresponding PL properties have been measured using the 488 nm line of an argon ion laser. The PL spectra of the film annealed at 350 degrees C for 21 h are stronger than those of the film annealed at 350 degrees C for 28 h, indicating a disorganized structure. The energy band gaps of the crystalline and amorphous BST:Sn thin films were 3.35 and 2.25 eV, respectively. The doped BST thin films also tend to a cubic structure, resulting from TiO6 deformations. (c) 2006 American Institute of Physics.

Microstructure and dielectric properties of (Ba,Sr)TiO3 thin film produced by the polymeric precursor method

BaxSr1-xTiO3 (x = 0.6) (BST) thin films were successfully prepared on a Pt(111)/TiO2/SiO2/Si(100) substrate by spin coating, using the polymeric precursor method. BST films with a perovskite single phase were obtained after heat treatment at 700 degrees C. The multilayer BST thin films had a granular structure will a grain size of approximately 60 nm. A 480-nm-thick film was obtained by carrying out five cycles of the spin-coating/heating process. Scanning electron microscopy and atomic force microscopy analyses showed that the thin films had a smooth, dense, crack-free surface with low surface roughness (3.6 nm). At room temperature and at a frequency of 100 kHz, the dielectric constant and the dissipation factor were, respectively, 748 and 0.042. The high dielectric constant value was due to the high microstructural quality and chemical homogeneity of the thin films obtained by the polymeric precursor method.

Ba1-xSrxTiO3 thin films by polymeric precursor method

Stoichiometric Ba1-xSrxTiO3 (BST; x = 0.4) thin films were prepared by the polymeric precursor method. High quality polycrystalline films of BST with low roughness (approximate to 3 nm) were obtained from a Pt/Ti/SiO2/Si substrate deposited by spin-coating technique. Microstructure and morphological evaluation were done using grazing incident X-ray diffraction (GIXRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Grazing incident angle XRD characterization of these films showed that BST phase crystallizes at 600 degrees C from an inorganic amorphous matrix. No intermediate crystalline phase was identified. A linear relationship between roughness and grain size was observed. (C) 2000 Elsevier B.V. B.V. All rights reserved.

Barium strontium titanate powder obtained by polymeric precursor method

Pure barium strontium titanate powder, with Ba/Sr ratio of 80/20 was prepared by the polymeric precursor method (also called Pechini process). The powder was obtained after a calcination at 800 degreesC for 8 h and characterized by XRD, IR, BET and SEM. The requirements to avoid barium carbonate as a secondary phase are presented and discussed in detail. (C) 2003 Elsevier B.V. All rights reserved.

Theoretical and experimental study of the relation between photoluminescence and structural disorder in barium and strontium titanate thin films

Thin films of barium and strontium titanate (BST), synthesized by the polymeric precursor solution and spin coated on [Pt (140nm)/Ti (10 nM)/SiO2(1000 nm)/Si] substrates were found to be photoluminescent at room temperature when heat treated below 973 K, i.e. before their crystallization. First principles quantum mechanical techniques, based on density functional theory (DFT) were employed to study the electronic structure of two periodic models: one is standing for the crystalline BST thin film and the other one for the structurally disordered thin film. The aim is to compare the photoluminescence (PL) spectra of the crystalline and disordered thin films with their UV-vis spectra and with their computed electronic structures. The calculations show that new localized states are created inside the band gap of the crystalline model, as predicted by the UV-vis spectra. The study of the charge repartition in the structure before and after deformation of the periodic model shows that a charge gradient appears among the titanate clusters. This charge gradient, together with the new localized levels, gives favorable conditions for the trapping of holes and electrons in the structure, and thus to a radiative recombination process. Our models are not only consistent with the experimental data, they also allow to explain the relations between structural disorder and photoluminescence at room temperature. (c) 2005 Elsevier Ltd. All rights reserved.

Barium strontium titanate nanocrystalline thin films prepared by soft chemical method

Barium strontium titanate (Ba0.65Sr0.35TiO3) nanocrystalline thin films, which were produced by the soft chemical method, were crystallized at low temperature using a domestic microwave oven. A SiC susceptor were used to absorb the microwave energy and rapidly transfer the heat to the film. Low microwave power and short time have been used. The films obtained are crack-free, well-adhered, and fully crystallized. The microstructure displayed a polycrystalline nature with nanograin size. The metal-BST-metal structure of the thin films treated at 700 degrees C show food electric properties. The ferroelectric nature of the BST35 thin film was indicated by buttertly- shaped C-V curves. The capacitance-frequency curves reveal that the dielectric constant may reach a value up to 800 at 100kHz. The dissipation factor was 0.01 at 100kHz. The charge storage density as function of applied voltage graph showed that the charge storage densities are suitable for use in trench type 64 Mb ( 1-5 mu C/cm(2) and 265 Mb (2-11 mu C/cm(2)) DRAMs. (C) 2007 Elsevier Ltd. All rights reserved.

Aerosol Deposition of Ba0.8Sr0.2TiO3 Thin Films

In this work we optimized conditions for aerosol deposition of homogeneous, nano-grained, smooth Ba0.8Sr0.2TiO3 thin films. Investigation involved optimization of deposition parameters, namely deposition time and temperature for different substrates. Solutions were prepared from titanium isopropoxide, strontium acetate and barium acetate. Films were deposited on Si (1 0 0) or Si covered by platinum (Pt (1 1 1) /Ti/SiO2/Si). Investigation showed that the best films were obtained at substrate temperature of 85 degrees C. After deposition films were slowly heated up to 650 degrees C, annealed for 30 min, and slowly cooled. Grain size of BST films deposited on Si substrate were in the range 40-70 nm, depending on deposition conditions, while the same films deposited on Pt substrates showed mean grain size in the range 35-50 nm. Films deposited under optimal conditions were very homogeneous, crack-free, and smooth with rms roughness lower than 4 nm for both substrates.

Effects of flunixin meglumine, recombinant bovine somatotropin and/or human chorionic gonadotropin on pregnancy rates in Nelore cows

The objective was to compare pharmacological strategies aiming to inhibit prostaglandin F2 alpha (PGF(2 alpha)) synthesis (flunixin meglumine; FM), stimulate growth of the conceptus (recombinant bovine somatotropin; bST) and progesterone (P(4)) synthesis (human chorionic gonadotropin; hCG), as well as their combinations, regarding their ability to improve pregnancy rates in beef cattle. Lactating Nelore cows (N = 975), 35 to 70 days postpartum, were synchronized and inseminated by timed artificial insemination (TAT) on Day 0. on Day 7, cattle were allocated into eight groups and received one of the following treatments: saline (S) on Days 7 and 16 (Group Control); S on Day 7 and FM on Day 16 (Group FM); bST on Day 7 and S on Day 16 (Group bST); bST on Day 7 and FM on Day 16 (Group bST + FM); hCG on Day 7 and S on Day 16 (Group hCG); hCG on Day 7 and FM on Day 16 (Group hCG + FM); bST and hCG on Day 7 and S on Day 16 (Group bST + hCG), or bST and hCG on Day 7 and FM on Day 16 (Group bST + hCG + FM). The aforementioned treatments were administered at the following doses: 2.2 mg/kg FM (Banamine (R); Intervet Schering-Plough, Cotia, SP, Brazil), 500 mg bST (Boostin (R); Intervet Schering-Plough), and 2500 IU hCG (Chorulon (R); Intervet Schering-Plough). Pregnancy diagnosis was performed 40 days after TAI by transrectal ultrasonography. Pregnancy rates were not significantly different among treatments. However, there was a main effect of hCG treatment to increase pregnancy rates (63.0 vs. 55.4%; P = 0.001). Concentrations of P(4) did not differ significantly among groups on Day 7 or on Day 16. However, consistent with the higher pregnancy rates, hCG increased P(4) concentrations on Day 16 (10.6 vs. 9.6 ng/mL, respectively; P = 0.05). We concluded that hCG treatment 7 days after TAI improved pregnancy rates of lactating Nelore cows, possibly via a mechanism leading to induction of higher P(4) concentrations, or by reducing the luteolytic stimulus during maternal recognition of pregnancy. (C) 2011 Elsevier B.V. All rights reserved.

Bone spreading technique a case report

Bone spreading technique (BST) is a horizontal augmentation with minimal trauma for simultaneous implant placement and an alternative to Summer's osteotome technique both for its clinical use and for the armamentarium. The foremost advantage of the crest dilation technique is a substantially less invasive method; the buccal wall expands after the medullary bone is compressed against the cortical bone. The lateral dilation and compaction of medullary bone improved primary stability. The vital difference is that the BST used in this case report avoided discomfort of the patient, thus eliminating the need for malleting.

Effects of bovine somatotropin injection on serum concentrations of progesterone in non-lactating dairy cows

The objective of this experiment was to evaluate the effects of bovine somatotropin administration on serum concentrations of glucose, insulin, NEFA, IGF-I, and progesterone (P4) in ovariectomized non-lactating dairy cows receiving exogenous P4, as a model to estimate treatment effects on hepatic P4 degradation. Ten non-lactating, non-pregnant, and ovariectomized Gir×Holstein cows were assigned to the experiment (d -14 to 27). On d 0, cows were ranked by BW and BCS, and randomly assigned to one of two treatments: (1) bovine somatotropin (BST; n=5) or (2) saline control (control; n=5). Cows assigned to the BST treatment were administered s.c. injections containing 500. mg of sometribove zinc on d 0, 9, and 18 of the experiment, whereas control cows concurrently received a 10-mL s.c. injection of 0.9% saline. On d -2, cows were inserted with an intravaginal releasing device containing 1.9. g of P4, which remained in the cows until the end the experiment (d 27). Cow BW and BCS were assessed on d -14, 0, and 27. Blood samples were collected daily from d 0 to d 27, at 0 (immediately before), 1, and 2. h relative to concentrate feeding for determination of serum glucose, insulin, NEFA, P4, and IGF-I concentrations. Concentrations of glucose, NEFA, and insulin obtained prior to feeding (0. h) were used to determine pre-prandial revised quantitative insulin sensitivity check index (RQUICKI). No treatment effects were detected for BW (P=0.72) and BCS change (P=0.79) during the experiment. Beginning on d 2 of the experiment, BST cows had greater (P≤0.01) serum IGF-I concentrations compared with control cohorts (treatment×day interaction; P<0.01). Cows receiving BST had greater (P≤0.05) insulin concentrations compared with control cohorts from d 8 to d 11, d 16 and 17, as well as from d 19 to d 21 of the experiment (treatment×day interaction; P<0.01). Cows receiving BST had greater (P≤0.01) mean glucose and NEFA concentrations, as well as reduced (P<0.01) mean RQUICKI during the experiment compared with control cohorts. No treatment effects, however, were detected (P=0.73) for serum P4 concentrations. In conclusion, results from this experiment indicate that hepatic P4 catabolism is not directly regulated by circulating IGF-I, whereas BST administration decreases insulin sensitivity in non-lactating dairy cows in adequate nutritional status. © 2013 Elsevier B.V.

Effects of bovine somatotropin administration on growth, physiological, and reproductive responses of replacement beef heifers

This experiment compared growth, body composition, plasma IGF-I and leptin, and reproductive development of beef heifers receiving or not recombinant bovine ST (BST) beginning after weaning until the first breeding season. Fifty Angus × Hereford heifers (initial BW = 219 ± 2 kg; initial age = 208 ± 2 d), weaned at approximately 6 mo of age, were assigned to the experiment (d 0 to 210). On d 0, heifers were ranked by initial BW and age and assigned to 1) treatment with BST or 2) saline control. Heifers assigned to the BST treatment received subcutaneous (s.c.) injections containing 250 mg of sometribove zinc whereas control heifers received a 5-mL s.c. injection of 0.9% saline every 14 d. Treatments were initiated on d 14 and last administered on d 196. Heifers were maintained on separate pastures harvested for hay the previous summer according to treatment and received grass and alfalfa hay at a rate to provide a daily amount of 7.0 and 1.0 kg of DM per heifer, respectively. Heifer shrunk BW was collected on d 1 and 211 for heifer ADG calculation. Blood samples were collected weekly from d 0 to 210 for determination of plasma progesterone to estimate puberty attainment as well as plasma concentrations of IGF-I and leptin in selected samples. On d 0, 63, 133, and 189, heifers were evaluated for intramuscular marbling, LM depth, and backfat thickness via real-time ultrasonography. No treatment effects were detected (P = 0.27) for heifer ADG (0.49 vs. 0.51 kg/d for control and BST heifers, respectively; SEM = 0.02). Mean backfat thickness was lesser (P < 0.01) in BST heifers compared with control cohorts (3.56 vs. 3.92 mm, respectively; SEM = 0.08). Heifers receiving BST had greater plasma IGF-I concentrations compared with control cohorts 7 d after treatment administration (treatment × day interaction; P < 0.01). Mean plasma leptin concentrations were lesser (P = 0.05) in BST heifers compared with control cohorts (1.82 vs. 2.03 ng/mL, respectively; SEM = 0.07). Onset of puberty was hastened in BST heifers compared with control cohorts (treatment x day interaction; P = 0.04). In summary, a greater proportion of BST heifers reached puberty during the experiment compared with control cohorts, despite lesser plasma leptin concentrations, backfat thickness, and similar ADG. Hence, circulating IGF-I was positively associated with hastened puberty attainment independently of growth rate, circulating leptin concentrations, and body fat content of replacement beef heifers. © 2013 American Society of Animal Science. All rights reserved.