Evaluation of the thermal shrinkage of titanium and the setting and thermal expansion of phosphate-boded investments

Statement of problem. There are few studies on titanium casting shrinkage, and phosphate-bonded investments for titanium casting have not produced appropriate marginal fit.Purpose. The purpose of this study was to determine the thermal shrinkage of titanium and the setting and thermal expansion of 3 phosphate-bonded investments.Material and methods. The thermal shrinkage between the melting temperature and room temperature was calculated using a titanium thermal expansion coefficient. The thermal and setting expansion were measured for 3 phosphate bonded investments: Rematitan Plus (RP) specific for titanium, Rema Exakt (RE), and Castorit Super C (CA), using different special liquid concentrations (100%, 75%, and 50%). Setting expansion was measured for cylindrical specimens 50 mm long x 8 mm in diameter with a transducer. The heating and cooling curves were obtained with a dilatometer (DIL 402 PC). The total expansion curve was drawn using software, and temperatures to obtain expansion equivalent to titanium casting shrinkage were determined (n=5). In addition, the total expansion of the control group (RP at 430 degrees C) was measured, as well as the temperatures at which the other groups achieved equivalent total expansion (n=5). Data were analyzed by 1-way ANOVA and the Tukey HSD test (alpha=.05).Results. Titanium casting shrinkage was estimated as 1.55%. RP did not achieve this expansion. RE achieved expansion of 1.55% only with a special liquid concentration of 100% at 594 degrees C. CA with all special liquid concentrations attained this expansion (351 degrees C to 572 degrees C). Total expansion of the control group was 0.86%, and the other groups reached that expansion within the range of 70 degrees C to 360 degrees C.Conclusions. Only RE and CA demonstrated sufficient expansion to compensate for titanium casting shrinkage. All groups reached total expansion equivalent to that of the control group at significantly lower temperatures.

Histological evaluation of the response of apical tissues to glass ionomer and zinc oxide eugenol based sealers in dog teeth after root canal treatment

The object of the study was to compare two commercial root canal sealers: Ketac-Endo (a glass ionomer cement) and Fill Canal (a zinc oxide-eugenol cement). A total of 34 root canals from dog premolars with vital pulps were used. After instrumentation, the root canals were sealed with Ketac-Endo and Fill Canal cements using gutta-percha and a lateral condensation technique. After 270 days the animals were sacrificed with an anesthetic overdose and the maxillae and mandibles were removed and fixed in formalin for 48 h. After routine histological processing the sections were stained with hematoxylin-eosin and Mallory trichrome stains. Microscopic analysis revealed that Ketac-Endo cement presented better results than Fill Canal cement.

Ultrastructural and immunocytochemical evaluation of the effects of extracorporeal shock wave treatment in the hind limbs of horses with experimentally induced suspensory ligament desmitis

Objective-To evaluate the effects of extracorporeal shock wave therapy (ESWT) on affected ligaments in the hind limbs of horses with experimentally induced suspensory ligament desmitis by use of ultrasonographic, ultrastructural, and immunocytochemical techniques.Animals-10 horses.Procedure-Suspensory ligament desmitis was induced in both hind limbs of each horse by use of 2 collagenase injections (administered 2 weeks apart) in each suspensory ligament. Two weeks after the second injection, the right hind limb of each horse was treated with ESWT (3 treatments at 3-week intervals)- the left hind limb was not treated (control limb). Periodically during the study, the healing process was monitored ultrasonographically and the proportions of ligaments affected with lesions were assessed. Four weeks after the last ESWT treatment, biopsy specimens were collected from all ligaments for ultrastructural evaluation and immunocytochemical analysis of transforming growth factor beta-1.Results-The difference in the proportion of the lesion-affected ligament between ESWT-treated and control limbs was significant (P < 0.05) from 3 weeks after the second ESWT treatment to the end of the study. Compared with control ligaments, ESWT-treated ligaments had more small, newly formed collagen fibrils and greater expression of transforming growth factor beta-1 4 weeks after the last ESWT treatment was administered.Conclusions and Clinical Relevance-Results have indicated that ESWT appears to facilitate the healing process in horses with experimentally induced hind limb suspensory ligament desmitis.

Magnesium levels in nutrient solution and common bean (Phaseolus vulgaris L cv Carioca) development. Evaluation of the growth relations and assimilate partitioning

The effect of magnesium levels in nutrient solution upon relation between shoot and root, leaf weight ratio and assimilate partitioning of common bean (Phaseolus vulgaris L. cv Carioca) was studied. Bean plants (3 per pot) were grown in 6 l pots containing Hoagland & Arnon n. 2 solution modified to obtain 2.4, 24.3, 48.6, 72.9 and 97.2 ppm of magnesium. The experimental design was a completely randomized factorial replicated 3 times with 5 levels of magnesium and 5 samplings wich were done forthnightly. Therefore, it may be suggested that the 48.6 ppm of magnesium level proposed by Hoagland & Amen (1950) is the best choice for the common bean, according to the conditions of this experiment. Magnesium concentrations over 48.6 ppm didn't show significant alterations of the evaluated parameters. Nutrient solution with 2.4 ppm of magnesium content provides higher efficiency to the common bean plants during almost all its cycle, except the final of the reproductive phase. These results suggest that magnesium concentration increased to 48.6 ppm, in the cycle final perhaps could increase the productivity.

Kinetic evaluation of the pyrolysis of high density polyethylene over H-AlMCM-41 material

The AlMCM-41 material with Si/Al=50 was synthesized by hydrothermal method, using cethyltrimethylammonium as template. The protonic H-AlMCM-41 acid form was obtained by ion exchange with ammonium chloride solution and subsequent calcination. The characterization of the material by several techniques showed that a good-quality MCM-41 material was obtained. High-density polyethylene (HDPE) has been submitted to thermal degradation alone, and in presence of the exchanged H-AlMCM-41 catalyst at a concentration of 1: 1 in mass (H-AlMCM-41/HDPE). The reactor was connected on line to a gas chromatograph connected to a mass spectrometer. This process was evaluated by thermogravimetry (TG), from 350 to 600degreesC, under helium dynamic atmosphere, with heating rates of 5.0; 10.0 and 20.0 degreesC/min. From TG curves, the activation energy, calculated using a multiple heating rate integral kinetic method, decreased from 225.5 KJ.mol(-1), for the pure polymer (HDPE), to 184.7 KJ.mol(-1), in the presence of the catalyst (H-AlMCM-41/HDPE).

Dielectric thermal analysis as a tool for quantitative-evaluation of the viscosity and the kinetics of epoxy resin cure

Dielectric thermal analysis has been proved as a valuable tool for monitoring the epoxy curing process and the related rheological properties in the fabrication of polymer-matrix composite materials. This technique also has the potential to be applied in the monitoring of magnet impregnation processes as well as in quality control. In this work we present the quantitative evaluation of the viscosity changing and the curing kinetics for a commercial Stycast epoxy resin system at different temperatures through the impedance analysis. The results showed correlation between the real component of the complex impedance and the isothermal reaction extent. Comparing the dielectric analysis result with the viscosity measured by rotational rheometer we observed a similar behavior reported for dynamic mechanic analysis. The results comparison have shown that the kinetics parameters obtained from DSC and DETA analysis showed different sensitivities related to the characteristics of curing stages. We concluded that the dielectric thermal analysis should be applied in quantitative evaluation of cure kinetics.

In vitro evaluation of the effectiveness of acidic fluoride dentifrices

This study evaluated the effectiveness of acidic low-fluoride dentifrices compared to conventional neutral dentifrices. Enamel blocks were submitted to pH cycling and treatment with slurries of dentifrices containing 0, 275, 412, 550 and 1,100 mu g F/g (pH 4.5 or 7.0), and also a commercial dentifrice (1,100 mu g F/g) and a commercial children's dentifrice (500 mu g F/ g). Variations in surface microhardness and in the mineral content in enamel after pH cycling were calculated. Enamel blocks treated with acidic dentifrices exhibited less mineral loss compared to neutral dentifrices (ANOVA; p < 0.05). The acidic dentifrices with 412 and 550 mu g F/g had the same effectiveness as the neutral 1,100-mu g F/g dentifrice and commercial 1,100-mu g F/g dentifrice. Copyright (c) 2007 S. Karger AG, Basel

Use of reduced concentrations of tetrazolium solutions for the evaluation of the viability of peanut seed lots

The possibility of reducing the concentration of the working solution used in the tetrazolium test for peanut seeds (Arachis hypogaea L.) with or without seedcoats was studied. Tetrazolium solutions of different concentrations (0.05%, 0.075% and 0.1%) were tested at the temperatures of 35 and 40 degrees C, for determining the time needed for the seeds to reach proper staining. The efficiency of the selected treatments in evaluating the viability potential of the seeds was determined by comparing the results of the tetrazolium tests with those obtained by standard germination (using sand and rolled paper towel as substrata) and seedling emergence in the field tests. Staining the seeds without seedcoat in 0.05% tetrazolium solution for three hours at 40 degrees C yielded efficient results. on the other hand, reduced concentrations can be employed in the staining process of seeds with seedcoat; however, this method requires a higher consumption of tetrazolium salt, longer staining time as well as a higher ability and availability of time for embryo evaluation, since the cross-cutting of seeds is much more difficult in the presence of the seedcoat and the occurrence of damage to the outer surface of the cotyledons cannot be determined.