The vinyl bromide optically pumped far infrared laser: New large offset emissions

We present the results of a study on vinyl bromide for the search for new far infrared (FIR) laser lines. As the pump source, we use a CW waveguide CO2 laser with a tunability of 290 MHz around each line in order to pump large offset vibrational transitions. As a consequence, we obtained 28 new FIR laser emissions; 24 of them have wavelengths greater than 500 mum and are, therefore, suitable to be used in high-field EPR spectroscopy, For each of the new lines, we give the wavelength, the offset of the pumping transition with respect to the center Frequency of the CO2 emission, the polarization relative to that of the pumping laser line, the operating pressure, and the relative intensity. We also present a catalog including data of all of the FIR laser lines observed from this molecule up to now.

Comparative Strain Gauge Analysis of External and Internal Hexagon, Morse Taper, and Influence of Straight and Offset Implant Configuration

Purpose: The present study was designed to analyze strain distributions caused by varying the fixture-abutment design and fixture alignment.Materials and Methods: Three implants of external, internal hexagon, and Morse taper were embedded in the center of each polyurethane block in straight placement and offset placement. Four strain gauges (SGs) were bonded on the surface of polyurethane block, which was designated SG1 placed mesially adjacent to implant A, SG2 and SG3 were placed mesially and distally adjacent to the implant B and SG4 was placed distally adjacent to the implant C. The 30 superstructures' occlusal screws were tightened onto the Microunit abutments with a torque of 10 N cm using the manufacturers' manual torque-controlling device.Results: There were statistically significant differences in prosthetic connection (P value = 0.0074 < 0.5). There were no statistically significant differences in placement configuration/alignment (P value = 0.7812 > 0.5).Conclusion: The results showed fundamental differences in both conditions. There was no evidence that there was any advantage to offset implant placement in reducing the strain around implants. The results also revealed that the internal hexagon and Morse taper joints did not reduce the microstrain around implants. (Implant Dent 2011; 20:e24-e32)

External Hexagon and Internal Hexagon in Straight and Offset Implant Placement: Strain Gauge Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Straight and Offset Implant Placement under Axial and Nonaxial Loads in Implant-Supported Prostheses: Strain Gauge Analysis

Purpose: The aim of this in vitro study was to quantify strain development during axial and nonaxial loading using strain gauge analysis for three-element implant-supported FPDs, varying the arrangement of implants: straight line (L) and offset (O). Materials and Methods: Three Morse taper implants arranged in a straight line and three implants arranged in an offset configuration were inserted into two polyurethane blocks. Microunit abutments were screwed onto the implants, applying a 20 Ncm torque. Plastic copings were screwed onto the abutments, which received standard wax patterns cast in Co-Cr alloy (n = 10). Four strain gauges were bonded onto the surface of each block tangential to the implants. The occlusal screws of the superstructure were tightened onto microunit abutments using 10 Ncm and then axial and nonaxial loading of 30 Kg was applied for 10 seconds on the center of each implant and at 1 and 2 mm from the implants, totaling nine load application points. The microdeformations determined at the nine points were recorded by four strain gauges, and the same procedure was performed for all of the frameworks. Three loadings were made per load application point. The magnitude of microstrain on each strain gauge was recorded in units of microstrain (mu). The data were analyzed statistically by two-way ANOVA and Tukey's test (p < 0.05). Results: The configuration factor was statistically significant (p= 0.0004), but the load factor (p= 0.2420) and the interaction between the two factors were not significant (p= 0.5494). Tukey's test revealed differences between axial offset (mu) (183.2 +/- 93.64) and axial straight line (285.3 +/- 61.04) and differences between nonaxial 1 mm offset (201.0 +/- 50.24) and nonaxial 1 mm straight line (315.8 +/- 59.28). Conclusion: There was evidence that offset placement is capable of reducing the strain around an implant. In addition, the type of loading, axial force or nonaxial, did not have an influence until 2 mm.

Determination of BTEX by GC-MS in air of offset printing plants: Comparison between conventional and ecological inks

The use of inks containing organic solvents by the offset printing process implies in the release of volatile organic compounds to the work environment. Many of these compounds such as benzene, toluene, ethylbenzene, and the xylene isomers (well known by the acronym BTEX) are extremely toxic. In this study, the BTEX concentrations were determined in two different printing plants that use distinct types of inks: the conventional and the so-called ecological, which is manufactured based on vegetal oil. Concentration ranges were 43-84, 15-3,480, 2-133, 5-459, and 2-236 μg m-3 for benzene, toluene, ethylbenzene, m + p-xylene, and o-xylene, respectively, for the conventional printing plant. At the ecological printing plant, concentration ranges were below limit of detection (

Extensometria: avaliação de implantes de sextavado externo posicionados na configuração linear e compensada (offset), sob carregamento axial

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The effect of offset implant configuration on bone stress distribution: a systematic review

Purpose: The aim of this systematic review was to compare straight-line and offset implant configurations for three-element implant-retained prostheses. Materials and Methods: Two independent reviewers conducted a review on PubMed/Medline, EMBASE, and Cochrane Library for studies published in English, from January 1, 1995 to January 17, 2014. A systematic review was conducted following the PRISMA statement. All relevant titles were selected according to inclusion/exclusion criteria. From this pool of titles, abstracts and full texts were reviewed. Results: A total of 6080 titles were identified with the initial search. Twenty-one were selected based on title and abstract. Of these, after discussion and complete reading, 12 studies were selected according to the inclusion and exclusion criteria, all of which were in vitro studies. Conclusions: A systematic review of the current literature showed only in vitro evidence that there is no consensus on the advantage of using an offset configuration implant compared to those in straight-line configuration, even though some studies present a slight improvement of bone stress distribution when an offset implant is under oblique loading (PICO).

Crescimento e produção de antúrio submetido a diferentes intensidades de desfolha

O objetivo do presente trabalho foi avaliar o crescimento e a produção de Anthurium andraeanum 'Apalai' submetido a diferentes intensidades de desfolha no Vale do Ribeira, SP. Foram utilizadas mudas micropropagadas dessa espécie, as quais foram plantadas em canteiros construídos sob telado coberto com tela de náilon preta, com malha que proporciona 70% de sombreamento, no espaçamento 0,40x0,40m. O experimento foi conduzido em delineamento de blocos casualizados em parcelas subdivididas, com dezesseis repetições. O efeito da desfolha foi avaliado na parcela e o efeito do tempo após a desfolha na subparcela. As diferentes intensidades de desfolha consistiram em plantas com três, quatro e cinco folhas e plantas sem desfolha, e o tempo após a desfolha, as avaliações realizadas em 2006 e 2007. Ocorreu um aumento na área das folhas individuais em plantas mantidas com quatro e cinco folhas, proporcional à intensidade de desfolha, que pode ser relacionado a uma tentativa de compensação da área foliar perdida. A desfolha com a manutenção de três, quatro ou cinco folhas em plantas de antúrio 'Apalai' é prejudicial para o seu crescimento e produção.

Comparison of analgesia provided by lidocaine, lidocaine-morphine or lidocaine-tramadol delivered epidurally in dogs following orchiectomy

ObjectiveTo evaluate and compare the postoperative analgesia provided by epidural lidocaine, lidocaine/morphine or lidocaine/tramadol in dogs following elective orchiectomy.Study designProspective experimental trial.AnimalsThirty-six mongrel dogs aged 2-8 years old, weighing 6.6-22 kg.MethodsThe dogs received 6.0 mg kg-1 of lidocaine combined with 1.0 mg kg-1 of tramadol, 0.1 mg kg-1 of morphine or 0.01 mL kg-1 of 0.9% NaCl epidurally. Analgesia was assessed at 4, 8, 12, 18 and 24 hours (T4, T8, T12 and T24) after the offset of lidocaine using a scale composed of physiologic and behavioral parameters. Rescue analgesia with morphine (0.2 mg kg-1, IM) was performed if the evaluation score exceeded 10 during the postoperative period. The scores over time were analyzed using the Friedman's two-way analysis of variance and the comparison between groups was made by the Kruskal-Wallis test with statistical significances accepted if p < 0.05.ResultsThere were no differences in the pain scores between the morphine and tramadol groups over time and no rescue analgesia was administered. In the NaCl group, rescue analgesia was needed at T4, T8 and T12. Within this group, the final evaluation times (T18 and T24) had lower pain scores than at T4, T8 and T12.Conclusions and clinical relevanceEpidural lidocaine/tramadol provided an analgesic effect comparable to that of epidural lidocaine/morphine during the first 12 hours after surgical castration without substantial side effects, suggesting that tramadol may be an effective postoperative analgesic in dogs submitted to this surgical procedure.

Efeito da escassez de alimento no desenvolvimento pós-embrionário e no potencial reprodutivo de Chrysoperla externa (Hagen) (Neuroptera: Chrysopidae) em laboratório

As conseqüências da escassez alimentar no período pós-embrionário e potencial reprodutivo de Chrysoperla externa (Hagen) em laboratório foram avaliadas. Larvas de 1.°, 2.º e 3.° ínstares receberam alimento apenas no 1.°, 2.º ou 3.° dia após a ecdise. Nos períodos em que antecederam ou sucederam os testes com os respectivos ínstares, as larvas receberam uma, duas e três unidades de alimentação (UA) a cada dois dias para o 1.°, 2.º e 3.° ínstares, respectivamente. Cada UA constou de um disco de cartolina contendo ovos de Sitotroga cerealella (Olivier) (Lepidoptera: Gelechiidae). Diariamente, avaliou-se a viabilidade nos diferentes ínstares, da fase larval e pupal, assim como os períodos de pré-oviposição e oviposição, o número e a viabilidade de ovos. A escassez de alimento durante o 1.° ínstar pode ser suprida no decorrer do desenvolvimento larval. Entretanto, as larvas precisam encontrar alimento nas primeiras 48 horas de vida, pois a viabilidade nesse ínstar foi decrescendo com a ausência de alimento, podendo ocorrer 100% de mortalidade quando as larvas não se alimentam em até 48 horas após a eclosão. Os períodos de pré-oviposição e oviposição, assim como a fecundidade, não foram influenciados pela escassez de alimento durante o 1.° ínstar larval. Durante os 2.° e 3.° ínstares larvais, C. externa necessita de alimentação rica em proteína, pois a ingestão de apenas água e açúcares nesses estádios ocasionou alta mortalidade. Entretanto, a fecundidade e viabilidade dos ovos não foram afetadas pela escassez de alimento nesses ínstares.

Consumo de combustível em diferentes sistemas de preparo periódico realizados antes e depois da operação de subsolagem

Foi estudado o consumo de combustível de diferentes sistemas de preparo periódico, realizados antes e depois da operação de subsolagem num solo classificado como Nitossolo Vermelho Distroférrico. As operações de preparo foram: a) 1 aração com arado de discos; b) 1 aração com arado de discos e 1 gradagem com grade destorroadora-niveladora; c) 1 gradagem com grade aradora; d) 1 gradagem com grade aradora e 1 gradagem com grade destorroadora-niveladora e; e) 1 escarificação com escarificador. O consumo específico (g kWh-1) de combustível para os diferentes sistemas de preparo periódico do solo variou estatisticamente com a condição de subsolagem realizada antes e depois. A escarificação proporcionou menor volume de combustível requerido por hectare (L ha-1) que os demais sistemas de preparo. O preparo do solo depois da subsolagem obteve um maior volume de combustível consumido por área (L ha-1).

Optical properties of polydisperse submicrometer aggregates of sulfur-containing zinc oxide consisting of spherical nanocrystallites

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Kinetics of interface state-limited hole injection in alpha-naphthylphenylbiphenyl diamine (alpha-NPD) thin layers

Injection-limited operation is identified in thin-film, alpha-NPD-based diodes. A detailed model for the impedance of the injection process is provided which considers the kinetics of filling/releasing of interface states as the key factor behind the injection mechanism. The injection model is able to simultaneously account for the steady-state, current-voltage (J-V) characteristics and impedance response. and is based on the sequential injection of holes mediated by energetically distributed surface states at the metal-organic interface. The model takes into account the vacuum level offset caused by the interface dipole, along with the partial shift of the interface level distribution with bias voltage. This approach connects the low-frequency (similar to 1 Hz) capacitance spectra, which exhibits a transition between positive to negative values, to the change in the occupancy of interface states with voltage. Simulations based on the model allow to derive the density of interface states effectively intervening in the carrier injection (similar to 5 x 10(12) cm(-2)), which exhibit a Gaussian-like distribution. A kinetically determined hole barrier is calculated at levels located similar to 0.4 eV below the contact work function. (C) 2008 Elsevier B.V. All rights reserved.

A multisampling time-domain CMOS imager with synchronous readout circuit

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

FIR laser lines from CH3OD: A review

The methanol isotopic species CH3OD has also proved to be an efficient and powerful medium to generate radiation in the far infrared (FIR) region. After the critical review of 1994, six papers have been published dealing with new FIR laser lines from this molecule. As a consequence of the use of wide tunability waveguide CO2 lasers as well as a new pulsed CO2 laser operating at hot and sequential bands, as of optical pumping sources, the total number of the FIR laser lines increased from 122 in 1994 to 227 today. In this communication we present an updated and complete catalogue of FIR laser lines generated from CH3OD. Information on wavelength, offset, relative polarization, intensity, and optimum operation pressure is generally available.