Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Estudo da potencialidade da incorporação de resíduo de granito e da queima da casca do café em cerâmica vermelha

The industrial production of ornamental rocks and the burning of coffee husk generate waste that is discarded into the environment. However, with the study of the incorporation of these residues in ceramic products, may be found an alternative to reducing environmental impacts and detrimental effects on human health caused by its indiscriminate disposal of waste in nature. Thus, this work aimed to study the addition of ashes of the coffee husk and granite residue in matrix of red ceramic. The raw materials were dry milled and sieved to mesh 100. To characterize the raw materials were carried out analyzes of X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis (PSA), differential thermal analysis (DTA) and thermogravimetric analysis (TG). Six formulations were prepared where the clay content was kept constant (70%wt) and ashes contents and granite residue varied from 10, 15, 20 and 30%. Dilatometrics analyzes were performed at four selected formulations, containing them: 100% clay (A100); 70% clay and 30% ashes (A70C30); 70% clay and 30% granite residue (A70G30); and 70% clay, 15% granite residue and 15% ashes (A70G15C15). The samples were prepared by uniaxial compaction with pressure of 25 MPa, and fired at temperatures of 800°C, 850ºC, 900ºC, 950ºC, 1000ºC and 1100°C. Assays were performed to determine the linear shrinkage of burning (LSB), water absorption (WA), apparent porosity (AP), density (D) and tensile bending. Also were performed analyzes of X-ray diffraction (XRD) and scanning electron microscopy (SEM) of the samples fired. The formulations incorporating granite residue and/or ashes reached the required limits of water absorption according to NBR 15270-1 and NBR 15310 and tensile bending according to classical literature (SANTOS, 1989) necessary for the production of tiles and ceramic block for masonry sealing

Utilização de resíduos de rochas ornamentais na produção de cerâmica branca

The marble and granite waste come from the process of mining of those ornamental rocks for use in the building industry. Brazil is one of the largest producers of blocks or finished products of ornamental rocks, extracting about 5.2 tons / year. The largest national producers are the states of Espírito Santo, Minas Gerais and Bahia which account for 80% of the Brazilian production. However, the waste total amount during processing of these blocks reaches 40% of the total. The use of the waste produced by this industry in white ceramics could be a form of disposition, because these materials, are thrownasa mud directly at decantation ponds, wastelands or in rivers, without any treatment. The present work has as main purpose to study the influence that reject of the ornamental rocks on the physical and mechanical properties of white ceramics. X-Ray characterizations of raw materials by were performed X-Ray fluorescence, X-Ray diffraction, granulometric, thermogravimetric and thermodiferencial analysis, five formulations were made (0, 10, 20, 30, 40% in granite weight) wich were burned at three temperatures: 1100°C, 1150°C and 1200ºC with 60 minutes of sorling time. After sintering, the samples were submitted to different analyser absorption of water, linear retraction, apparent porosity, apparent specific mass, flexival stronght, and scanning were obtained microscopy. Compatible technological properties within the limits demanded for the production of porcelainized stoneware

Efeito da introdução de resíduo de cinza de forno cerâmico em massa para cerâmica estrutural

The red ceramics and structural ceramics, as they are known, include ceramic materials made by blocks of seals and structures, bricks, tiles, smail flagstones manacles, rustic floors and ornamental materials. Their fabrication uses raw material such as clay and clay sites, with some content of impurity. It has good durability and mechanical strength to compression, low cost, making it one of the mainly used materials in civil engineering. The incorporation of many industrial activities residue to ceramic products is a technological alternative for reducing the environmental impact caused by its carefree disposal. This incorporation can promote chemical change and inertness of metals from residue, by fixation in the glassy phase of ceramic during the burning stage. The main aim of this project is to study the technical feasibility of the addition of ceramic oven ash into formulations of mass for structural ceramics. In this project two kinds of clay (plastic and non-plastic) were used, as well as the ash from firewood used in the process of burning of structural ceramics. A group of experiments was outlined, which permitted the evaluation of the influence of the burning cycle in different temperatures of the ash content in formulations for ceramic blocks through technological properties, mechanical behavior and microstructure. Five samples were processed of each one of the masses of plastic and non-plastic clay without addition of ash and with addition of ash on the percentages of 10 % and 20 %, for temperatures of 850 °C, 950 °C, 1050 °C and 1150 °C, obtained through sinterization process. Among the studied compositions, the one which presented best performance was the mass of clay with 10 % of ash, at temperature of 1150 °C, with the smallest absorption of water, the smallest apparent porosity, specific apparent mass a bit over the others and greatest mechanical resistance to flexion. The composition made confirmed the technical feasibility of the use of ash in the mass for structural ceramics with maintenance of its necessary characteristics for its purposes

O discurso do grotesco na mídia digital

This study presents our research on the discourse of the grotesque in digital media, specifically in two blogs. We rely on the theoretical-conceptual and methodological discourse analysis of the French School. We analyzed a set of posts in the following blogs: Eu Sou Ryca and Cleycianne, and we did it based on some propositions on the discourse of the grotesque by Mikhail Bakhtin (1999a), Muniz Sodré and Raquel Paiva (2002), Wolfgang Kayser (2003) and Mary Russo (2000). The expressions of the grotesque analyzed in the blogs Eu Sou Ryca and Cleycianne result predominantly in humorous effect, obtained by means of irony and parodization, which calls for ridicule and relegation, through a strong tension between the beautiful and the ugly, the socially acceptable and the aberration, the taste for the strange and the aesthetically striking. The grotesque appears initially as a significant feature of ornamental paintings found in Roman caves in the late fifteenth century, and today it can be seen permeating from sculptures, paintings, literary works, talk shows for television, videos hosted in cyberspace, specifically in the collective domain of weblogs. This work seeks to analyze how the discourse of the grotesque constitutes the humorous process in its insertion in cyberspace

Adaptabilidade de híbridos entre Gossypium barbadense E G. hirsutum N contendo o gene cry1Ac

Hybrids among transgenic plants and related species are expected to occur if they are sympatric and when there are not crossing barriers; as is the case, in Brazil, of cry1Ac transgenic cotton and Gossypium barbadense. This species has been maintained as dooryard plants, and should be preserved as a genetic resource. Hybrids were evaluated about traits related to fitness, leading to infer about its chances of survivor and selection. A barbadense genotype collected at the state of Mato Grosso was outcrossed to the variety DP 404, containing the gene cry1Ac, and to the isoline DP 404. All the F1 individuals and 122 among 170 F2 individuals expressed the toxin, and presented levels of resistance to pink bollworm (Pectinophora gossypiella) and cotton leafworm (Alabama argillacea) equivalent to the transgenic parent and superior to the isoline, barbadense or non transgenic hybrids. The percentage of germination and number of days to germinate did not differ among genotypes. Anthesis of the first flower and opening of the first cotton boll occurred earlier for herbaceous cotton and F1 hybrids than F2 population in average; all the populations presented a number of days to flower and opening of the first boll smaller then barbadense. The highest plants were barbadenses, and herbaceus the smallest, with F1 and F2 populations presenting intermediary heights. The number of seeds per plants were superior for F1 hybrids an herbaceous cotton, F2 populations were in average intermediary; the barbadense genotype produced the smallest number of seeds per plant. Pink bollworm, mainly, and also cotton leafworm, are important barbadense pests, so the transgene positive effect could favor the selection of hybrids, and hence G. hirsutum genome, against the maintenance of pure G. barbadense genome. The selection may be influenced by the plant uses: the smaller size of hybrids when compared to the barbadense may lead them to be differentiated from these parents to which medicinal properties are attributed; on the other hand, the greater boll production may favor hybrids maintenance with the purpose of producing lamp wicks, or use as an ornamental or swab

Zoneamento geoambiental como subsídio ao planejamento territorial municipal: estudo de caso para Currais Novos/RN

This paper presents the master plan and geoenvironmental zoning natures as instruments of environmental planning and management. The discussion of territory environmental planning is guided by two directions: at first the environmental elements involved in planning and the another is the implementation of these instruments at the municipal territory. To analyze the planning directed of the municipal territory we consider the fragments of its, represented by country and urban. The master plan inside of the Estatuto da Cidade (City Statute) and the geoenvironmental zoning are directed to territorial environmental planning. Regarding of the master plan the first challenge has been the spacial area that the plan can cover. It is necessary to prepare master plans that could include all the territory. The environmental zoning are directed for the territory totality.In this sense, the geoenvironmental zoning of the Currais Novos was done in the totality of the municipal territory and guided by the environmental physics variables. The geoenvironmental zoning sets in a planning and ordering of the territory instrument based in the landscape analysis. Therefore grounded in the Geosystems‟s Theory this work has like a main objective to propose a geoenvironmental zoning for the Currais Novos Municipality in RN. So, was used an analysis technique suggested for Bardin (2010) and the Currais Novos‟s physical environment characterization through of the fieldwork and cartographic data vectorization, beyond the image‟s treatment SRTM. The geoenvironmental systems definitions were based in the suggestion of Cestaro, et al. (2007) support in Bertrand (1968). For both were identified five geoenvironmental systems: Borborema Plateau, Residual plateau, Chapada da Serra de Santana, semiarid river valley and lagoon valley and eleven geoenvironmental subsystems: Borborema Plateau Western Slope, Isolated Massif of the Borborema Plateau, Residual Crest, Residual Massif, Erosional Scarp of the Chapada, flat top plateau, fluvial plains, temporary river of the semiarid and ornamental water or sluice

Estudo integrado geológico/tecnológico de rochas ornamentais: os granitos flores e jacarandá, RN

The main purpose of the present study is to integrate a geological and technological investigation of ornamental rocks of the Flores and Jacarandá granites, which are located near the Afonso Bezerra city, in the north central part of the Rio Grande do Norte State. The study area encompasses four litho-stratigrafic units: a Gneiss-Migmatitic Complex(cristalline basement), which is mainly composed of banded gneisses, usually deformed as mylonitic rocks and with several migmatic features, an Augen Gneiss, which occurs as an elongated body that constitutes the Jacarandá granite, a small granite stock, which presents a semi-circular form, named Flores granite, composed of pink, fine to medium coarse rocks, and fine to coarse alluvial sediments, which form extensive areas of large fluvial deposits. The technological characterization of the Flores and Jacarandá granites, carried out through several tests, has as the main purpose the determination of petrographic, physical, and mechanic parameters that allowed the characterization of these rocks. The test followed procedures recommended by Brazilian (ABNT Associação Brasileira de Normas Técnicas) and foreigner institutions (ASTM American Society for Testing and Materials). The petrografhic analysis indicated that the rocks investigated are granite sensu estrictu, summing an average 85-90% modal. The Flores granite is the more felsic rock, which presents mafic content ∼ 10% and monzonitic composition. The Jacarandá granite is an Augen Gneiss rock that presents sienogranitic composition and mafic modal content ∼ 15%. Several technological tests carried out (alterability, physical indices, velocity of ultrasonic wave propagation, uniaxial compression, flection resistence, Amsler desgaste, and resistence to freezing and heating) indicated that parameters and values were identical for both granites investigated. These parameters and values are consistent with the Brazilian and international standards for siliciclastic rocks of ornamental use, as well as other Brazilian ornamental granites. The analysis of all results indicates that both the Flores and Jacarandá granites present good quality, and that they are indicated for ornamental use of revetment interior and exterior of buildings