Reciclagem de material asfáltico fresado utilizando solventes e microemulsões

With the increase of asphalt milling services was also a significant increase in recycling services pavements. The techniques used today are basically physical processes in which the milled material is incorporated into new asphalt mixtures or executed on site, with the addition of virgin asphalt and rejuvenating agent. In this paper seeks to analyze the efficiency of extraction of CAP (Petroleum Asphalt Cement) mixtures from asphalt milling, using commercial solvents and microemulsions. The solvents were evaluated for their ability to solubilize asphalt using an extractor reflux-type apparatus. Pseudoternary diagrams were developed for the preparation of microemulsion O/W surfactant using a low-cost coconut oil saponified (OCS). Microemulsions were used to extract the CAP of asphalt through physicochemical process cold. Analysis was performed concentration of CAP in solution by spectroscopy. The data provided in the analysis of concentration by the absorbance of the solution as the basis for calculating the percentage of extraction and the mass flow of the CAP in the solution. The results showed that microemulsions prepared with low concentration of kerosene and butanol/OCS binary has high extraction power of CAP and its efficiency was higher than pure kerosene, reaching 95% rate of extraction

Caracterização de compósitos Nb-20%cu obtidos por moagem de alta energia e sinterizados por fase líquida

In this work, was studied the formation of a composite of the refractory metal niobium with copper, through the process of high-energy milling and liquid phase sintering. The HEM can be used to synthesize composite powders with high homogeneity and fine size particle distribution. It may also produce the solid solubility in immiscible systems such as Nb-Cu, or extend the solubility of systems with limited solubility. Therefore, in the immiscible system Cu-Nb, the high-energy milling was successfully used to obtain the composite powder particles. Initially, the formation of composite particles during the HEM and the effect of preparation technique on the microstructure of the material was evaluated. Four loads of Nb and Cu powders containing 20%wt Cu were synthesized by MAE in a planetary type ball mill under different periods of grinding. The influence of grinding time on the metal particles is evaluated during the process by the withdrawal of samples at intermediate times of milling. After compaction under different forces, the samples were sintered in a vacuum furnace. The liquid phase sintering of these samples prepared by HEM produced a homogeneous and fine grained. The composite particles forming the sintered samples are the addition of a hard phase (Nb) with a high melting point, and a ductile phase (Cu) with low melting point and high thermal and electrical conductivities. Based on these properties, the Nb-Cu system is a potential material for many applications, such as electrical contacts, welding electrodes, coils for generating high magnetic fields, heat sinks and microwave absorbers, which are coupled to electronic devices. The characterization techniques used in this study, were laser granulometry, used to evaluate the homogeneity and particle size, and the X-ray diffraction, in the phase identification and to analyze the crystalline structure of the powders during milling. The morphology and dispersion of the phases in the composite powder particles, as well the microstructures of the sintered samples, were observed by scanning electron microscopy (SEM). Subsequently, the sintered samples are evaluated for density and densification. And finally, they were characterized by techniques of measuring the electrical conductivity and microhardness, whose properties are analyzed as a function of the parameters for obtaining the composite

Formulação de bloco intertravado cerâmico com adição de resíduos urbanos e industriais

The production of waste from urban and industrial activities is one of the factors of environmental contamination and has aroused attention of the scientific community, in the sense of its reuse. On the other hand, the city of Salvador/Ba, with approximately 262 channels, responsible for storm water runoff, produces every year, by the intervention of cleaning and clearing channels, a significant volume of sediments (dredged mud), and thus an appropriate methodology for their final destination. This study aims to assess the influence of incorporation of these tailings in arrays of clay for production of interlocked block ceramic, also known as ceramic paver. All the raw materials from the metropolitan region of Salvador (RMS) were characterized by x-ray fluorescence, x-ray diffraction, thermal analysis (TG and TDA), particle size analysis and dilatometry. With the use of statistical experimental planning technique, ternary diagram was defined in the study region and the analyzed formulations. The specimens were prepared with dimensions of 60x20x5mm³, by uniaxial pressing of 30 MPa and after sintering at temperatures of 900°, 1000º and 1100ºC the technological properties were evaluated: linear shrinkage, water absorption, apparent porosity, apparent specifies mass, flexural rupture and module. For the uniaxial compression strength used cylindrical probe body with Ø 50 mm. The standard mass (MP) was prepared with 90% by weight of clay and 10% by weight of Channel sediment (SCP), not being verified significant variations in the properties of the final product. With the incorporation of 10% by weight of manganese residue (PFM) and 10% by weight of the Ceramic waste (RCB) in the mass default, in addition to adjusting the plasticity due to less waste clay content, provided increased linear firing shrinkage, due the significant concentration of K2O, forming liquid phase at low temperature, contributing to decreased porosity and mechanical resistance, being 92,5 MPa maximum compressive strength verified. After extract test leachate and soluble, the piece containing 10% of the PFM, was classified as non-hazardous and inert material according to NBR10004/04 ABNT. The results showed the feasibility on using waste, SCP, RCB and PFM clay mass, at temperatures above 900ºC, paver ceramic production, according to the specifications of the technical standards, so that to exceed the 10% of the PFM, it becomes imperative to conduct studies of environmental impacts

Extração de boro de água produzida sintética por sistema microemulsionado

Boron is a semi-metal present in certain types of soils and natural waters. It is essential to the healthy development of plants and non-toxic to humans, depending on its concentration. It is used in various industries and it s present in water production coming from oil production. More specifically in Rio Grande do Norte, one of the largest oil producers on shore of Brazil, the relationship water/oil in some fields becomes more than 90%. The most common destination of this produced water is disposal in open sea after processing to meet the legal specification. In this context, this research proposes to study the extraction of boron in water produced by microemulsion systems for industrial utilization. It was taken into account the efficiency of extraction of boron related to surfactant (DDA and OCS, both characterized by FT-IR), cosurfactant (butanol and isoamyl alcohol), organic phase (kerosene and heptanes) and aqueous phase (solution of boron 3.6 ppm in alkaline pH). The ratio cosurfactant/ surfactant used was four and the percentage of organic phases for all points of study was set at 5%. It was chosen points with the highest percentage of aqueous phase. Each system was designed for three points of different compositions in relation to the constituents of a pseudoternary diagram. These points were chosen according to studies of phase behavior in pseudoternary diagrams made in previous studies. For this research, points were chosen in the Winsor II region. The excess aqueous solution obtained in these systems was separated and analyzed by ICP OES. For the data set obtained, the better efficiency in the extraction of boron was obtained using the system with DAC, isoamyl alcohol and heptanes, which extracted 49% in a single step. OCS was not viable to the extraction of boron by microemulsion system in the conditions defined in this study

Extração de metais (K, Mg, Ba, Ca, Cr, Mn, Li, Fe) de água produzida utilizando sistema microemulsionado

The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation

Avaliação da efetividade de estratégias não farmacológicas para o alívio da dor de parturientes na fase ativa do período de dilatação no trabalho de parto

This study was aim to evaluate the effectiveness of strategies non pharmacological for the relief of the intensity of the parturient pain in the phase activates of the dilation period in the labor. Is a clinic rehearse of the type therapeutic intervention before and after" with a quantitative approach, accomplished in the Humanized Unit of Childbirth of the Maternity Januário Cicco School of the Federal University of Rio Grande do Norte, in Natal/RN, whit 130 parturient, being 30 in the pre-test of the strategies and 100 in the application of the strategies non pharmacological combined (breathing exercises, muscular relaxation and lombossacral massage) and isolated (shower bath in a normal temperature). We used the visual analogical scale to evaluate the intensity of the pain of the study parturient before and after" to the application of the strategies in the phases of acceleration, maximum inclination and desaceleration in the phase activates of dilation period in the labor. The principal results showed that the majority of the study parturient was between 20 to 30 years old (60%); with incomplete fundamental teaching (85%); family income until 2 minimum wages (74%); 78% had a companion and these, 44% were the own husband. The oxytocin was administered in the parturient during the phase activates of the labor in 81% of the cases and only 15% these women didn´t reciev anything medication. We verified significant relief (ρ=0.000) of intensity of the pain of the study parturient after application of the strategies non pharmacological combined and isolated. We concluded that the strategies non pharmacological combined and isolated were effective in the relief of the pain of the study parturient in the phase activates de labor

Avaliação de um método de cromatografia em fase gasosa head space e estudo da estabilidade do etanol em amostras de sangue

The ethanol is the most overused psychoactive drug over the world; this fact makes it one of the main substances required in toxicological exams nowadays. The development of an analytical method, adaptation or implementation of a method known, involves a process of validation that estimates its efficiency in the laboratory routine and credibility of the method. The stability is defined as the ability of the sample of material to keep the initial value of a quantitative measure for a defined period within specific limits when stored under defined conditions. This study aimed to evaluate the method of Gas chromatography and study the stability of ethanol in blood samples, considering the variables time and temperature of storage, and the presence of preservative and, with that check if the conditions of conservation and storage used in this study maintain the quality of the sample and preserve the originally amount of analyte present. Blood samples were collected from 10 volunteers to evaluate the method and to study the stability of ethanol. For the evaluation of the method, part of the samples was added to known concentrations of ethanol. In the study of stability, the other side of the pool of blood was placed in two containers: one containing the preservative sodium fluoride 1% and the anticoagulant heparin and the other only heparin, was added ethanol at a concentration of 0.6 g/L, fractionated in two bottles, one being stored at 4ºC (refrigerator) and another at -20ºC (freezer), the tests were performed on the same day (time zero) and after 1, 3, 7, 14, 30 and 60 days of storage. The assessment found the difference in results during storage in relation to time zero. It used the technique of headspace associated with gas chromatography with the FID and capillary column with stationary phase of polyethylene. The best analysis of chromatographic conditions were: temperature of 50ºC (column), 150ºC (jet) and 250ºC (detector), with retention time for ethanol from 9.107 ± 0.026 and the tercbutanol (internal standard) of 8.170 ± 0.081 minutes, the ethanol being separated properly from acetaldehyde, acetone, methanol and 2-propanol, which are potential interfering in the determination of ethanol. The technique showed linearity in the concentration range of 0.01 and 3.2 g/L (0.8051 x + y = 0.6196; r2 = 0.999). The calibration curve showed the following equation of the line: y = x 0.7542 + 0.6545, with a linear correlation coefficient equal to 0.996. The average recovery was 100.2%, the coefficients of variation of accuracy and inter intra test showed values of up to 7.3%, the limit of detection and quantification was 0.01 g/L and showed coefficient of variation within the allowed. The analytical method evaluated in this study proved to be fast, efficient and practical, given the objective of this work satisfactorily. The study of stability has less than 20% difference in the response obtained under the conditions of storage and stipulated period, compared with the response obtained at time zero and at the significance level of 5%, no statistical difference in the concentration of ethanol was observed between analysis. The results reinforce the reliability of the method of gas chromatography and blood samples in search of ethanol, either in the toxicological, forensic, social or clinic

Alcoolemia em vítimas fatais de acidentes de trânsito no Rio Grande do Norte empregando cromatografia em fase gasosa - head space

Alcohol is one of the few psychotropic drugs that their consumption has admitted legally and sometimes encouraged by the society. Studies show alcohol as the highest consumption of drugs among young people and society in general, probably because of its availability and easy access. The abuse causes public health problems, which was closely related to the violence, socioeconomic problems and the high number of automobile accidents. Transit is one of the main sectors affected by the effects of alcohol, observing a high incidence in the studies. About half of automobile accidents occurs after the consumption of alcoholic beverage, and the vast majority of cases related to high concentrations of alcohol in the bloodstream. The relationship of drunk with traffic accidents is in fact evident everywhere in the world, including Brazil, where studies have shown a high relationship between alcohol consumption and traffic accidents. This study determined the alcohol in fatal victims of traffic accidents in the state of Rio Grande do Norte and established the profile of this population compared with those found in Brazil and other countries. Samples of blood of ethanol added to fulfillment of the standardization of chromatographic conditions and procedures for the analysis, being employed in the determination of alcohol in blood samples of 277 victims of traffic accidents, collected at the Institute of Scientific Technical Police of Rio Grande do North (ITEP) in the year 2007. The blood alcohol level was determined in these samples correlated with the sex, age and marital status of the victim and the location, day of week and month when the accident occurred, is doing a statistical analysis and outlining a profile of the victims of an accident at transit in the state of Rio Grande do Norte. The parameters of standardization studied ensured the quality of the analytical method and, consequently, to obtain reliable laboratory results. Being given the best temperature for injector (150 ºC), detector (250 ºC) and column (50 ºC) with a flow of gas in the column of 2mL/minutos and analysis of time of 12 minutes. The method was linear in the range of 0.01 to 3.2 g / L (r2 = 0.9989) with average recovery of 100.2% and precision with coefficient of variation less than 15%. The analysis carried out on victims of fatal road traffic accidents, ethanol detected in the blood in 66.43% of the victims and these, 96% showed concentration ≥ 0.2 g / L, 87.73% of victims were male, while 12.27% female. The younger age group (1535 years) was the most involved (52,35%) and most single (55.60%). The accidents occurred with greater prevalence in the day on Monday (27%) followed by Sunday (24,19%) and Saturday (15,52%) and it was found that the prevalence of injuries varied between the different months of the year, and in February (14.4%) and April (10.47%) the months that had a higher number of accidents, however this oscillation showed no statistically significant difference. Also no significant difference was observed between the tracks of concentration found in men and women. The standardized method showed to be efficient, given satisfactorily to the goals of this work, and the high levels of alcohol found in victims of fatal road traffic accidents are consistent with several studies of literature, and the profile of the victim also supported by presenting in its most young adults, male and single

FERRITINA: intervalos de referência para adultos no Estado do Rio Grande do Norte

Ferritin is a protein composed of heavy and light chains, non-covalently linked and which accommodates, in its core, thousands of atoms of iron. Furthermore, this protein represents the stock of iron in the body and it is characterized as an acute marker and predictor of diseases, such as iron deficiency anemia, hereditary hemochromatosis and others. Considering the variability of reference values and the analytical methods currently available, the aim of this work was to propose 95% confidence intervals for adults in the State of Rio Grande do Norte, Brazil, after determining the average concentration of serum ferritin for both sexes, beyond its correlation with the age. We analyzed 385 blood samples, collected by venipuncture from individuals residing in the State, after 12-14 hours of fast. The populational sample had 169 men and 216 women between 18-59 years old, which filled a questionnaire on socioeconomic, food habits and accounts about previous and current diseases. The sample collections were itinerant and the results of erythrogram, fasting glucose, alanine aminotransferase, aspartate aminotransferase, γ-glutamyl transferase, urea, creatinine, leukocyte count and platelets, beyond C-reactive protein, were issued to each participant, so that, after selection of the apparently healthy individuals, the dosage of serum ferritin was carried out. Statistical analysis was performed using the softwares SPSS 11.0 Windows version, Epi Info 3.3.2 and Graf instant pad (version 3.02), and the random population sample was single (finite population), for which the test of linear correlation and diagram of dispersion were also made. After selection of individuals and determination of serum ferritin, the most discrepant outliers were disregarded (N = 358, Men = 154/Women = 207) and the average value determined for the masculine sex individuals was 167,18 ng / dL; for the feminine sex individuals, the average value obtained was 81,55 ng / dL. Moreover, we found that 25% of men had values < 90,30 ng / dL; 50% ≤ 156,25 ng / dL and 75% ≤ 229,00 ng / dL. In the group of women, 25% had values < 38,80 ng / dL; 50% ≤ 65,00 ng / dL and 75% ≤ 119,00 ng / dL. Through the correlation coefficient (r = 0,23 with p = 0,003), it is possible to suggest the existence of positive linear correlation between age and serum ferritin for men. The correlation coefficient for women (r = 0,16 with p = 0,025) also confirms the existence of positive linear correlation between serum ferritin and age. Considering the analysis carried out and specific methods corroborating with the proposed benchmarks, we concluded that the average value found for men is higher than that found for women. Furthermore, this scenario rises with age for both sexes, and the 95% confidence intervals obtained were 74 ng/dL ≤ μ ≤ 89 ng/dL and 152ng/dL ≤ μ ≤183ng/dL for the feminine and masculine sex individuals respectively

Preparação e caracterização de sistemas emulsionados contendo benznidazol

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Preparação e caracterização de sistemas emulsionados lipidicos contendo praziquantel

Praziquantel (PRZ) is the main drug used for treatment of schistosomiasis in Brazil. It is administered by oral rout as tablets. However, has low aqueous solubility which limits this therapeutic success dosage form and availability of liquid forms. The emulsion systems have great potential and represent an interesting strategy to increase the solubility of drugs. The aim of study was the development and characterization of lipid-emulsified liquid systems of the type oil in water (O / W), the base of soybean oil as the internal phase stabilized by surfactants pair Tween® 80 and Span® 80, for improving the phase biopharmaceutical of PRZ. After selecting the best value of Hydrophilic-Lipophilic Balance (HLB = 11), the parameters of the preparation of the formulations were optimized emulsification technique. The emulsions were successfully obtained; the liquid forms provided exhibited Newtonian behavior and an increase in solubility of PRZ higher than 20 times. The accelerated stability study demonstrated the stability of the emulsions and the effect of cosurfactants investigated. The study of the dynamics of interaction between components in the diagram showed pseudoternary phase regions to obtain O/W emulsions, whereas the study of the interaction of the components and their effect on system structure and the efficiency of incorporation of the drug led to systems with an amount of soluble drug even higher (about 1.5%), which demonstrates the potential of this new input mainly for the treatment of schistosomiasis, which resulted in the filing of patent BR 10 2013 0004 55 3

Materiais supercondutores HTS para arranjos de antenas e aplicação de PBG para micro-ondas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Otimização do controle eletrônico do diagrama de radiação de arranjos de antenas usando algoritmos genéticos com codificação real

Antenna arrays are able to provide high and controlled directivity, which are suitable for radiobase stations, radar systems, and point-to-point or satellite links. The optimization of an array design is usually a hard task because of the non-linear characteristic of multiobjective, requiring the application of numerical techniques, such as genetic algorithms. Therefore, in order to optimize the electronic control of the antenna array radiation pattem through genetic algorithms in real codification, it was developed a numerical tool which is able to positioning the array major lobe, reducing the side lobe levels, canceling interference signals in specific directions of arrival, and improving the antenna radiation performance. This was accomplished by using antenna theory concepts and optimization methods, mainly genetic algorithms ones, allowing to develop a numerical tool with creative genes codification and crossover rules, which is one of the most important contribution of this work. The efficiency of the developed genetic algorithm tool is tested and validated in several antenna and propagation applications. 11 was observed that the numerical results attend the specific requirements, showing the developed tool ability and capacity to handle the considered problems, as well as a great perspective for application in future works.

Utilização de RNA´s na construção do diagrama de vida constante de probabilidade de materiais compósitos

The static and cyclic assays are common to test materials in structures.. For cycling assays to assess the fatigue behavior of the material and thereby obtain the S-N curves and these are used to construct the diagrams of living constant. However, these diagrams, when constructed with small amounts of S-N curves underestimate or overestimate the actual behavior of the composite, there is increasing need for more testing to obtain more accurate results. Therewith, , a way of reducing costs is the statistical analysis of the fatigue behavior. The aim of this research was evaluate the probabilistic fatigue behavior of composite materials. The research was conducted in three parts. The first part consists of associating the equation of probability Weilbull equations commonly used in modeling of composite materials S-N curve, namely the exponential equation and power law and their generalizations. The second part was used the results obtained by the equation which best represents the S-N curves of probability and trained a network to the modular 5% failure. In the third part, we carried out a comparative study of the results obtained using the nonlinear model by parts (PNL) with the results of a modular network architecture (MN) in the analysis of fatigue behavior. For this we used a database of ten materials obtained from the literature to assess the ability of generalization of the modular network as well as its robustness. From the results it was found that the power law of probability generalized probabilistic behavior better represents the fatigue and composites that although the generalization ability of the MN that was not robust training with 5% failure rate, but for values mean the MN showed more accurate results than the PNL model

Desenvolvimento de uma unidade laboratorial para quantificação de BTX como poluentes atmosféricos, usando microextração em fase sólida

This dissertation aims the development of an experimental device to determine quantitatively the content of benzene, toluene and xylenes (BTX) in the atmosphere. BTX are extremely volatile solvents, and therefore play an important role in atmospheric chemistry, being precursors in the tropospheric ozone formation. In this work a BTX new standard gas was produced in nitrogen for stagnant systems. The aim of this dissertation is to develop a new method, simple and cheaper, to quantify and monitor BTX in air using solid phase microextraction/ gas chromatography/mass spectrometry (SPME/CG/MS). The features of the calibration method proposed are presented in this dissertation. SPME sampling was carried out under non-equilibrium conditions using a Carboxen/PDMS fiber exposed for 10 min standard gas mixtures. It is observed that the main parameters that affect the extraction process are sampling time and concentration. The results of the BTX multicomponent system studied have shown a linear and a nonlinear range. In the non-linear range, it is remarkable the effect of competition by selective adsorption with the following affinity order p-xylene > toluene > benzene. This behavior represents a limitation of the method, however being in accordance with the literature. Furthermore, this behavior does not prevent the application of the technique out of the non-linear region to quantify the BTX contents in the atmosphere.