Materiais zeolíticos de estrutura MWW: síntese e caracterização

In this paper a synthesis parameters study was conducted in order to optimize the obteinment of MCM-22 (MWW structure) and increase its accessibility, getting higher external surface and generating mesopores. Syntheses with Si / Al = 15 and Si / Al = 50 ratios were performed under static conditions at different temperatures and with seeds induction, which resulted in MCM-22 pure and crystalline (Si / Al ratio = 15) after 3 days and Si / Al = 50 after 11 days. The reduction of hexamethyleneimine content (HMI) was studied in the stirring synthesis and a HMI reduction of 47% was possible through the mother liquor reuse, in addition, a specific area of 481 m² / g has been obtained in the fourth synthesis day. Regarding the increase of accessibility of the MCM-22 zeolite skeins of MCM-22 plates with about 2 μm were obtained, through the use of dissolved silica, addition of seeds, increased temperature and synthesis time of 2 days. A significant value of specific area was found for this material, around 500 m² / g. Also with respect to the increase of MCM-22 accessibility, treatment with oxalic acid concentration of 0.5 mol / L and silanization of proto-zeolitic units resulted in the mesopores formation . Furthermore, silanization still favored reduction of 70 % in crystal size and a specific area of 566 m² / g.

Análise do desempenho térmico de um sistema de aquecimento solar utilizando coletor com superfície absorvedora em chapas de PVC

It s presented a solar collector to be used in a system for heating bath water, whose main characteristic is its low cost. The collector consists of five plates of PVC with 10 mm thick, 200 mm in width and 1400mm in length, with an area equal to 1.4 square meters. The plates were connected in parallel to the ends of PVC tubes of  40 mm and 32 mm. The plates were coated on one side with aluminum sheets of soft drinks and beers cans open. The system worked on a thermosiphon and was tested in two configurations: the plates uncoated and coated with aluminum material, to determine the influence of material on the efficiency of the collector. For both configurations was used EPS plates below the surface to minimize heat losses from the botton. The thermal reservoir of the heating system is, also, alternative and low cost, since it was constructed from a polyethylene tank for storing water, with volume of 150 end 200 liters. It will be presented the thermal efficiency, heat loss, water temperature of the thermal reservoir at the end of the process and simulation of baths for a house with four residents. The will be demonstrated thermal, economic and material viability of the proposed collector, whose main innovation is the use of recyclables materials, cans of beer and soft drinks, to increase the temperature of the absorber plate.

Análise do potencial genotóxico da superfície de titânio modificada por plasma

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas

ALVES, Ana paula Melo. Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas. 2009. 124 f. Tese (Doutorado em Quimica) - Centro de Ciências Exatas e da Natureza, Universidade Federal da Paraíba, João Pessoa, PB, 2009.

Avaliação histomorfométrica do efeito do ultrasom pulsado nas falhas ósseas provocadas em fêmures de rato: estudo experimental

SILVA, J. S. P. Avaliação histomorfométrica do efeito do ultrasom pulsado nas falhas ósseas provocadas em fêmures de rato: estudo experimental . 2000. 85 f. Dissertação (Mestrado) – Faculdade de Medicina, Universidade de São Paulo. São Paulo, 2000.

Comunidade fitoplanctônica e qualidade da água da lagoa do jiqui, parnamirim, rn

It is important to evaluate the quality of water for proper management of these resources, since the increase of environmental degradation and the multiple use of water resources are decreasing the quality of water consumed by living beings. The objective of this study was to characterize the phytoplankton community and its variations during periods of dray and rain in Jiqui Lake located in Parnamirim, RN. It was also aimed to analyze the physical and chemical factors of this environment, in order to contribute to the knowledge of water quality used for human consumption. The collection of water samples were carried out in September 2008 to August 2009. The collection of the phytoplankton community was carried out in four sampling sites (surface, bottom, margin of the lake without macrophytes and site dominated by macrophytes). Phytoplankton was collected using plankton net of 20m. The analysis of nutrients and identification of phytoplankton were performed in the laboratory. The results indicate that concentration of chlorophyll a was high in the bottom with mean value of 1.07 μgL-1 (SD ± 1.61). During the study period there was a dominance of the following species: Euglena gracilis, Trachelomonas sp, Cyclotellas sp, Gomphonema apuncto, Navicula cuspidata var. cuspidata, Navicula sp, Rhopalodia gibba. There was homogeneity between limnological values in the four study sites, with significant difference between the periods of drought and rain. The Jiqui Lake is considered oligotrophic due to its low concentrations of chlorophyll a, high transparency and low levels of nutrients. The values of BOD and chlorophyll a concentration remained below the permitted standards existing for freshwaters in Brazil, thus the water from Lake Jiqui is of good quality, suitable for human consumption.

Utilização da macroalga Ulva lactuca linnaeus na redução de nutrientes (NH4+,NO3- e PO4-2) provenientes da carcinicultura

Dentre as macroalgas capazes de absorver altas concentrações de N e P dissolvidos na água, destaca-se a Chlorophyta Ulva lactuca, bastante adaptável e resistente às adversidades ambientais, como grandes variações de temperatura, salinidade, matéria orgânica e metais pesados. Trata-se também de uma espécie bastante comum nas áreas intertidais do litoral norte-riograndense. Devido a suas características ecológicas, fisiológicas e nutricionais, foi avaliado nesse estudo, o seu potencial como biofiltro na redução de NH4+, NO3- e PO4-2, tanto em condições controladas como também em um viveiro de camarão. No experimento laboratorial, foram utilizados quatro aquários de vidro de 30 x 20 x 20cm com 10L de água, sendo três aquários experimentais contendo 20g de U. lactuca e um controle. O acréscimo de biomassa foi de 2,92g (22,92 ± 6,29g; p < 0,05) em relação ao inóculo inicial de 20g, sob temperatura (28,50 ± 0,58ºC), salinidade (35,00 ± 0,00 ), pH (8,26 ± 0,02) e luz constante (250 μmol.m2s-1). O crescimento positivo (1,78 ± 4,38%dia-1; p < 0,05), juntamente com a alta eficiência de absorção de amônio (83%; p < 0,001), nitrato (83%; p < 0,001) e ortofosfato (53%; p < 0,001), demonstrou que, nessas condições, a Ulva lactuca absorveu os nutrientes e aumentou sua biomassa. Já no experimento de campo, realizado na fazenda TECNARÃO, situada no município de Arez/RN (06° 11 40 Latitude Sul, e 35º 09 37 Longitude Oeste), foram utilizadas três gaiolas de PVC, posicionadas a 12cm da superfície da água, cada uma com dimensões de aproximadamente 59 x 59 x 15cm, onde foram colocadas 200g de U. lactuca. O ganho de biomassa de 3g (203,00 ± 41,02g; p < 0,001) foi muito semelhante às condições controladas, demonstrando a adaptabilidade da espécie em condições ambientais variáveis, onde, apesar da temperatura pouco variável (27,45 ± 0,64ºC), houve progressiva diminuição de salinidade (25 - 15 ), devido ao período de fortes chuvas (34,70 ± 23,78mm). Somado a isso, foram observados vários fatores biológicos interferindo no viveiro, como a presença de epífitas, organismos endofíticos, fouling e a herbivoria por parte dos próprios camarões. Houve aumento nas concentrações de NH4+ (4,36 ± 1,69 μmol.L-1), NO3- (0,17 ± 0,25μmol.L-1) e PO4-2 (0,41 ± 0,13μmol.L-1), coincidindo com o crescimento da espécie até a terceira semana. Todos os parâmetros ambientais analisados, assim como a biomassa e a Taxa de Crescimento Relativo (TCR), obtidos no campo, apresentaram variações altamente significativas (p < 0,001). As correlações observadas entre biomasa e NH4+ (r = 0,82; p < 0,001) e entre biomassa e PO4-2 (r = 0,87; p < 0,001), indicam que esta espécie é capaz de ter um crescimento satisfatório nas condições eutróficas de um viveiro de camarão, sendo possível seu uso como biofiltro.

Efeito sacietogênico de um novo inibidor de tripsina da paçoca do amendoim com aumento plasmático de colecistocinina (cck)

Obesity is increasing, reaching epidemic levels in many regions of the world. Studies have shown that consumption of peanuts influences on weight control and this influence may be due to the action of trypsin inhibitors sacietogênica that condition increased plasma colescistocinina (CCK). Moreover, the peanut has other health benefits, and these assignments are guaranteed to increase their production and consumption of several of its products, including the paçoca peanut. The aim of this study was to identify the presence of a trypsin inhibitor in paçoca peanut and evaluate its effect on food intake, weight gain and histomorphological changes in swiss mice (n = 8) and Wistar rats (n = 6). Experimental diets were prepared based on the AIN-93G and supplemented with tack or peanut trypsin inhibitor partially purified paçoca peanut (AHTI). After each treatment, the animals were anesthetized and euthanized, their bloods were collected by cardiac puncture for the determination of CCK and other biochemical parameters (glucose, triglycerides, total cholesterol, high density lipoprotein, low density lipoprotein, glutamic-pyruvic transaminase, glutamic oxaloacetic transaminase and albumin) and their pancreas removed for histologic and morphometric analysis. The supplementation with paçoca peanut and the AHTI showed a decrease of body weight gain and food intake in both mice and rats, due to the satiety, since the animals showed no evidence of impairment of nutritional status conditioned by consumption the AHTI. There were also observed biochemical or morphological important when compared with controls. However, AHTI led to increased secretion of CCK, a peptide sacietogênico. Thus, these results indicate that AHTI present in paçoca peanut, is able to enhance the secretion of plasma CCK and thereby reduce the weight gain associated with lower food intake of experimenta animals

Estudo da adesão de pinos endodônticos modificados superficialmente por plasma de oxigênio

The work presents the effect of plasma treatment when applied in fibers or carbon/glass posts in the adhesion fiber/resin and posts/cement. This has for objective the modification of the surface of the fibers, as well as the wettability of the posts, seeking the improvement of the adhesion and of the connection fiber/resin in the processing of polymeric composites reinforced with the same ones. 120 posts (Reforpost) were used and 30 meters of fibers of carbon and of glass (Fibrex), of the company Angelus. The samples were divided in three groups of 40 specimens: GROUP I - 20 posts of glass fiber and 20 of carbon without treatment to it shapes, GROUP II -20 posts of glass fiber and 20 of carbon treated to it shapes in the surface and GROUP III - 20 posts of glass fiber and 20 of carbon make with fibers in natura after plasma treatment. The plasma treatment was accomplished with oxygen and with temperature in the camera fixed at 200°C, for one hour of exhibition. The posts and the fibers were characterized before and after the treatment. The wettability was measure by pendent drop method, and interface fiber/resin and posts/cement were observed by optical and electronic microscopy. It was observed that both wettability and texture were increased with plasma treatment

Obtenção e caracterização de nanopartículas de argilominerais

Natural nanoclays are of great interest particularly for the production of polymer-based nanocomposites. In this work, kaolinite clays from two natural deposits in the State of the Rio Grande do Norte and Paraiba were purified with thermal treatment and chemical treatments, and characterized. Front to the gotten data, had been proposals methodologies for elimination or reduction of coarse particle texts, oxide of iron and organic substance. These methodologies had consisted of the combination of operations with thermal treatments, carried through in electric oven, and acid chemical attacks with and hydrogen peroxide. The Analyzers Thermogravimetric was used to examine the thermal stability of the nanoclays. The analysis indicated weight losses at temperatures under 110 ºC and over the temperature range of 350 to 550 ºC. Based on the thermal analysis data, the samples were submitted to a thermal treatment at 500 °C, for 8 h, to remove organic components. The X-ray diffraction patterns indicated that thermal treatment under 500 °C affect the basic structure of kaolinite. The BET surface area measurements ranged from 32 to 38 m2/g for clay samples with thermal treatment and from 36 to 53 m2/g for chemically treated samples. Thus, although the thermal treatment increased the surface area, through the removal of organic components, the effect was not significant and chemical treatment is more efficient, not affect the basic structure of kaolinite, to improve particle dispersion. SEM analysis confirms that the clay is agglomerated forming micron-size particles

Processamento e análise de imagens na caracterização da superfície do titânio submetido a um ensaio de cultura de células

This work aims to develop a methodology for analysis of images using overlapping, which assists in identification of microstructural features in areas of titanium, which may be associated with its biological response. That way, surfaces of titanium heat treated for 08 (eight) different ways have been subjected to a test culture of cells. It was a relationship between the grain, texture and shape of grains of surface of titanium (attacked) trying to relate to the process of proliferation and adhesion. We used an open source software for cell counting adhered to the surface of titanium. The juxtaposition of images before and after cell culture was obtained with the aid of micro-hardness of impressions made on the surface of samples. From this image where there is overlap, it is possible to study a possible relationship between cell growth with microstructural characteristics of the surface of titanium. This methodology was efficient to describe a set of procedures that are useful in the analysis of surfaces of titanium subjected to a culture of cells

Modificação de membranas de quitosana por plasma para uso biológico

Chitosan membranes have been modified by plasma, utilizing the following gases: nitrogen (N2), methane (CH4), argon (Ar), oxygen (O2) and hydrogen. The modified membranes by plasma were compared to the unmodified ones. The membranes were characterized by absorption assay, contact angle, atomic force microscopy (AFM). Also, permeability assay of sodium sulfamerazine from such membranes were carried out. Through the absorption assay and contact angle it was possible to obtain information of the wettability of the membranes and what changes the plasma treatment can promote in relation to it. The plasma treatment using oxygen promoted increase of the wetability and swelling while the samples treated with methane decrease of the wetability and swelling. Through the Optical Emission Spectroscopy (OES) it was possible to identify which species were present in the plasma during the treatment. And through the AFM analysis it was possible to observe the changes nanotopography occurred on the surface of the samples. Permeability assay were archived for all treated membranes and compared to no treated ones. Due to that assay it was possible verify which the plasma treatment increased the permeability spectrum of the membranes which has varied from 1,4548 *10-5cm2.min-1 to 2,7713*10-5cm2.min-1. Chitosan membranes with permeability varied are importance in systems drug delivery, to liberate a wide variety of drugs

Estudo e desenvolvimento de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential substitute, since both belong to the same group of the periodic table and because of this have many similar physical and chemical properties. Niobium has several technologically important applications, and Brazil has the largest reserves, around 96%. There are including niobium in reserves of tantalite and columbite in Rio Grande do Norte. These electrolytic capacitors have high capacitance specifies, ie they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium powder supplied by EEL-USP was first characterized by XRD, SEM, XRF and laser particle size, to then be sieved into three particle size, 200, 400 e 635mesh. The powders were then compacted and sintered at 1350, 1450 and 1550°C using two sintering time 30 and 60min. Sintering is one of the most important parts of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. The sintered samples then underwent a process of anodic oxidation, which created a thin film of niobium pentóxido over the whole porous surface of the sample, this film is the dielectric capacitor. The oxidation process variables influence the performance of the film and therefore the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor, ESR, relative density, porosity and surface area. After the characterizations was made an annealing in air ate 260ºC for 60min. After this treatment were made again the electrical measurements. The particle size of powders and sintering affected the porosity and in turn the specific area of the samples. The larger de area of the capacitor, greater is the capacitance. The powder showed the highest capacitance was with the smallest particle size. Higher temperatures and times of sintering caused samples with smaller surface area, but on the other hand the cleaning surface impurities was higher for this cases. So a balance must be made between the gain that is achieved with the cleaning of impurities and the loss with the decreased in specific area. The best results were obtained for the temperature of 1450ºC/60min. The influence of annealing on the loss factor and ESR did not follow a well-defined pattern, because their values increased in some cases and decreased in others. The most interesting results due to heat treatment were with respect to capacitance, which showed an increase for all samples after treatment

Estudo de revestimentos inorgânicos com inibidor de corrosão aplicado na superfície do concreto

The corrosive phenomenon on reinforced concrete structures is one of the most founded pathologies on the coastal area. With the objective to prevent the process development, or even, retard its beginning, it was studied the application of inorganic covering over concrete surfaces, after its cure, as well as, evaluate the efficiency of the covering applied on the concrete in reducing its porosity of concrete preventing the entrance of aggressive agents to preserve the integrity of the existing armor inside it, comparing the result obtained with the body-of-proof reference, that didn´t receive covering protection. On the concrete production it was used Portland Cement CP II 32, coarse aggregate, fine aggregate and water from the local distributive. Two types of covering were used, one resin based of silicon and solvent and other white cement based, selected sands and acrylic resin. The concrete mixture adopted was 1:1,5:2,5 (cement, fine aggregate, coarse aggregate) and 0.50 water/cement ratio. With the concrete on fresh state was made the experiment test to determinate the workability. On the hardened state was made the concrete resistance experiment, absorption of water and electrochemical experiments, through polarization curves. Also was held optical microscopy and Scanning Electron Microscopy experiments to analyze the layer of the covering applied to the concrete surface and the interface between the concrete and the layer. The obtained results shows that the covering applied to the concrete surface didn´t affect the resistance towards compression. On the absorption of water occurred a diminution of the percentage absorbed, improving the concrete development by making it more impermeable towards the entrance of aggressive agents. The electrochemical experiment results confirmed the water absorption results; the body-of-proof covered presented larger protection towards the development of corrosives process and retarded the evolution of the corrosive phenomenon

Estudo da viabilidade técnica para obtenção de superfície duplex em aço inoxidável martensítico AISI 410 através do processo de deposição a plasma por gaiola catódica

The technique of plasma nitriding by the cathode cage mainly stands out for its ability to produce uniform layers, even on parts with complex geometries. In this study, it was investigated the efficiency of this technique for obtaining duplex surface, when used, simultaneously, to nitriding treatment and thin film deposition at temperatures below 500°C. For this, were used samples of AISI 41 0 Martensitic Stainless Steel and performed plasma treatment, combining nitriding and deposition of thin films of Ti and/or TiN in a plasma atmosphere containing N2-H2. It was used a cathodic cage of titanium pure grade II, cylindrical with 70 mm diameter and 34 mm height. Samples were treated at temperature 420ºC for 2 and 12 hours in different working pressures. Optical Microscopy (OM), Scanning Electron Microscopy (SEM) with micro-analysis by Energy Dispersive Spectroscopy (EDS), X-Ray Diffraction (XRD), Atomic Force Microscopy (AFM) and analysis of Vickers Microhardness were used to investigate coating properties such as homogeneity and surface topography, chemical composition, layer thickness, crystalline phase, roughness and surface microhardness. The results showed there is a direct proportionality between the presence of H2 in plasma atmosphere and the quantity of titanium in surface chemical composition. It was also observed that the plasma treatment at lowpressure is more effective in formation of TiN thin film