Desenvolvimento de um painel sanduíche com carga de particulado oriundo de resíduo lignocelulósico para aplicação em produtos na área de equipamentos de proteção

This work aims to study and investigate the use of a hybrid composite polymer formed with blanket aramid (Kevlar 29) fiber blanket flax fiber and particulate dry endocarp of coconut (Cocos nucifera Linn), using as matrix an epoxy resin based thermoset for use in areas of protective equipment. Besides such material is used an aluminum plate, joined to the composite by means of glue based on epoxy and araldite commercial. The manufacturing process adopted was manual lamination (Hand Lay Up) to manufacture the hybrid composite. After the composite is prepared, an aluminum plate is subjected to pressure and glued to cure the adhesive. Layers of veil will also be used to separate the particulate from the linen blanket layer without disturbing the alignment of the fibers of the blankets. To characterize the mechanical and physical behavior was manufactured a plate of 800 x 600 mm of the hybrid composite, which were removed specimens for tests of water absorption to saturation; density; impact test (Charpy) and two test specimens for ballistic testing 220 mm x 200 mm to make a comparative study between the dry state and saturated water absorption and thus see the ballistic performance of these two conditions. The test was applied to make a comparative study of fracture in these two conditions, caused by penetrating ballistic missile (38 and 380). To test the impact (Charpy) will analyze the absorbed energy, fracture appearance and lateral contraction, also in dry condition and saturation of absorbed water, thereby analyzing situations where the impact load is relevant, such as bumps and shocks produced by stone, metal or wooden bars among others. The proposed configuration, along with the tests, has the purpose, application in the fields of equipment against ballistic impact, such as helmets; bullet proof vests; shields; protective packaging and other items to be identified in this research.

Gestão ambiental e competitividade no setor da construção civil :um estudo sobre a aceitabilidade de práticas ambientais no mercado imobiliário

This work investigates the importance of Eco-Materiais applied in the civil construction and the necessity of knowledge of the real estate market, showing the importance of application of recycled products where inserted inside of a bigger scope of the sustainable development which has the subjects as the ambient management. In the theoretical referencial boarded the recycled and perfectly ecological products that demonstrate the applicability of this type of products in the sector of the civil construction, beyond the economic and social placesThe main popouse of the real estate sector is to show the awareness and demonstration in the negotiation of property constructed with these products, therefore, already it is practised by the market of the civil construction where much time sao commercialized by real estate and the its correctors lacking in same knowledge that is more deepened on these materials, having this evidence been made with statistical application of questionnaire and analyzed with base. We finish showing the statistical results with application of 142 questionnaires in a universe of 145 real estate from Natal/RN. With this, we may say that today exists a very strong concern with the environmental laws and the generated ambient impact in the civil construction and that the real estate sector has a feeling that the necessity of if inserting in this process, therefore, the real estate market in our State is in expansion and sensible to the necessity of changes, since the Natal/RN meets in the script of the tourism the International demanding of the professional that a globalized knowledge works with property, so the necessity of understanding the environmental laws and understanding application of the echo-materias used in the construction will give a better quality of life and at the same time to protect the nature

Aplicação do planejamento de experimentos no processo de desenvolvimento de produtos: pesquisa em uma sorveteria artesanal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - CAPES

Influência dos intermediários de distribuição de produtos turísticos no processo de decisão do meio de hospedagem pelo consumidor

This study examines the complex hotel buyer decision process in front of the tourism distribution channels. Its objective is to describe the influence level of the tourism marketing intermediaries, mainly the travel agents and tour operators, over the hotel decision process by the buyer-tourist. The data collection process was done trough a survey with three hundred brazilian tourists hosted in nineteen hotels of Natal, capital of Rio Grande do Norte, Brazil. The data analysis was done using some multivariate statistic techniques as correlation analysis, multiple regression analysis, factor analysis and multiple discriminant analysis. The research characterizes the hotel services consumers profile and his trip, and identifying the distribution channels used by them. Furthermore, the research verifies the intermediaries influence exercised over hotel buyer decision process, looking for identify causality relations between the influence level and the buyer profile. Verifies that information about hotels available on internet reduces the probability that this influence can be practiced; however it was possible identifying those consumers considers this information complementary and non-substitutes than the information from intermediaries. The characteristics of the data do not allow indentifying the factors that constraint the intermediaries influence neither identifying discriminant functions of the specific distribution channel choice by consumers. The study concludes that consumers don t agree in have been influenced by intermediaries or don t know if they have, still considering important to consult them and internet doesn t substitute their function as information source

Sinterização de Ce1-XEuXO2-(X/2) para aplicação como eletrólito sólido em células a combustível de temperaturas intermediárias

Given the environmental concern over global warming that occurs mainly by emission of CO2 from the combustion of petroleum, coal and natural gas research focused on alternative and clean energy generation has been intensified. Among these, the highlight the solid oxide fuel cell intermediate temperature (IT-SOFC). For application as electrolyte of the devices doped based CeO2 with rare earth ions (TR+ 3) have been quite promising because they have good ionic conductivity and operate at relatively low temperatures (500-800 ° C). In this work, studied the Ce1-xEuxO2-δ (x = 0,1, 0,2 and 0,3), solid solutions synthesized by the polymeric precursor method to be used as solid electrolyte. It was also studied the processing steps of these powders (milling, compaction and two step sintering) in order to obtain dense sintered pellets with reduced grain size and homogeneous microstructure. For this, the powders were characterized by thermal analysis, X-ray diffraction, particle size distribution and scanning electrons microscopy, since the sintered samples were characterized by dilatometry, scanning electrons microscopy, density and grain size measurements. By x-ray diffraction, it was verified the formation of the solid solution for all compositions. Crystallites in the nanometric scale were found for both sintering routes but the two step sintering presented significant reduction in the average grain size

Síntese e caracterização de catalisadores nanométricos de LaSrNiO4 para aplicação em dessulfurização de tiofeno

The mixed metal oxides constitute an important class of catalytic materials widely investigated in different fields of applications. Studies of rare earth nickelates have been carried by several researchers in order to investigate the structural stability afforded by oxide formed and the existence of catalytic properties at room temperature. So, this study aims synthesize the nanosized catalyst of nickelate of lanthanum doped with strontium (La(1-x)SrxNiO4-d; x = 0,2 and 0,3), through the Pechini method and your characterization for subsequent application in the desulfurization of thiophene reaction. The precursor solutions were calcined at 300ºC/2h for pyrolysis of polyester and later calcinations occurred at temperatures of 500 - 1000°C. The resulting powders were characterized by thermogravimetric analysis (TG / DTG), surface area for adsorption of N2 by BET method, X-ray diffraction (XRD), scanning electron microscopy (HR_SEM) and spectrometry dispersive energy (EDS). The results of XRD had show that the perovskites obtained consist of two phases (LSN and NiO) and from 700ºC have crystalline structure. The results of SEM evidenced the obtainment of nanometric powders. The results of BET show that the powders have surface area within the range used in catalysis (5-50m2/g). The characterization of active sites was performed by reaction of desulfurization of thiophene at room temperature and 200ºC, the relation F/W equal to 0,7 mol h-1mcat -1. The products of the reaction were separated by gas chromatography and identified by the selective detection PFPD sulfur. All samples had presented conversion above 95%

Obtenção de polímeros de LCC para aplicação como antioxidante de biodiesel de soja

Biodiesel is a fuel obtained from vegetable oils, such as soy, castorbean, among others. The monoester of fatty acid of these oils have chains with mono, di and tri double connections. The presence of these insaturations are susceptible to oxidization. Antioxidants are substances able to prevent oxidization from oils, fats, fat foods, as well as esters of Alquila( biodiesel). The objective of this work is to summarize a new antioxidant from the Cashew Nut Shell Liquid (CNSL) using the electrolysis technique. A current of 2 amperes was used in a single cell of only one group and two eletrodos of stainless steel 304 in a solution of methanol, together with the eletrolits: acetic acid, sodium chloride and sodium hydroxide, for two hours of agitation. The electrolysis products are characterized by the techniques of cromatography in a thin layer, spectroscopy of infrared and gravimetric analysis. The material was submitted to tests of oxidative stability made by the techniques of spectropy of impendancy and Rancimat (EN 14112). The analyses of characterization suggest that the polimerization of the electrolytic material ocurred. The application results of these materials as antioxidants of soy biodiesel showed that the order of the oxidative stability was obtained by both techniques used

Aplicação de termogravimetria acoplada à espectrometria de massas para caracterização de petróleo e determinação da curva de evolução de gás sulfídrico

With the new discoveries of oil and gas, the exploration of fields in various geological basins, imports of other oils and the development of alternative fuels, more and more research labs have evaluated and characterized new types of petroleum and derivatives. Therefore the investment in new techniques and equipment in the samples analysis to determine their physical and chemical properties, their composition, possible contaminants, especification of products, among others, have multiplied in last years, so development of techniques for rapid and efficient characterization is extremely important for a better economic recovery of oil. Based on this context, this work has two main objectives. The first one is to characterize the oil by thermogravimetry coupled with mass spectrometry (TG-MS), and correlate these results with from other types of characterizations data previously informed. The second is to use the technique to develop a methodology to obtain the curve of evaluation of hydrogen sulfide gas in oil. Thus, four samples were analyzed by TG-MS, and X-ray fluorescence spectrometry (XRF). TG results can be used to indicate the nature of oil, its tendency in coke formation, temperatures of distillation and cracking, and other features. It was observed in MS evaluations the behavior of oil main compounds with temperature, the points where the volatilized certain fractions and the evaluation gas analysis of sulfide hydrogen that is compared with the evaluation curve obtained by Petrobras with another methodology

Desenvolvimento de sistemas de aditivos químicos para aplicação em cimentações de poços de petróleo

The primary cementing is an important step in the oilwell drilling process, ensuring the mechanical stability of the well and the hydraulic isolation between casing and formation. For slurries to meet the requirements for application in a certain well, some care in the project should be taken into account to obtain a cement paste with the proper composition. In most cases, it is necessary to add chemicals to the cement to modify its properties, according to the operation conditions and thus obtain slurries that can move inside the jacket providing a good displacement to the interest area. New technologies of preparation and use of chemicals and modernization of technological standards in the construction industry have resulted in the development of new chemical additives for optimizing the properties of building materials. Products such as polycarboxylate superplasticizers provide improved fluidity and cohesion of the cement grains, in addition to improving the dispersion with respect to slurries without additives. This study aimed at adapting chemical additives used in civil construction to be used use in oilwell cement slurries systems, using Portland cement CPP-Special Class as the hydraulic binder. The chemical additives classified as defoamer, dispersant, fluid loss controller and retarder were characterized by infrared absorption spectroscopy, thermogravimetric analyses and technological tests set by the API (American Petroleum Institute). These additives showed satisfactory results for its application in cement slurries systems for oil wells. The silicone-based defoamer promoted the reduction of air bubbles incorporated during the stirring of the slurries. The dispersant significantly reduced the rheological parameters of the systems studied. The tests performed with the fluid loss controller and the retarder also resulted in suitable properties for application as chemical additives in cement slurries

Síntese, caracterização e aplicação de LaSBA-15 e como catalisador para obtenção de biodiesel de soja via rota etílica

Biodiesel is an alternative fuel, renewable, biodegradable and nontoxic. The transesterification of vegetable oils or animal fat with alcohol is most common form of production of this fuel. The procedure for production of biodiesel occurs most commonly through the transesterification reaction in which catalysts are used to accelerate and increase their income and may be basic, acid or enzyme. The use of homogeneous catalysis requires specific conditions and purification steps of the reaction products (alkyl ester and glycerol) and removal of the catalyst at the end of the reaction. As an alternative to improve the yield of the transesterification reaction, minimize the cost of production is that many studies are being conducted with the application of heterogeneous catalysis. The use of nano-structured materials as catalysts in the production of biodiesel is a biofuel alternative for a similar to mineral diesel. Although slower, can esterify transesterified triglycerides and free fatty acids and suffer little influence of water, which may be present in the raw material. This study aimed at the synthesis, characterization and application of nano-structured materials as catalysts in the transesterification reaction of soybean oil to produce biodiesel by ethylic route. The type material containing SBA-15 mesoporous lanthanum embedded within rightly Si / La = 50 was used catalyst. Solid samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, nitrogen adsorption and desorption. For the transesterification process, we used a molar ratio of 20:1 alcohol and oil with 0.250 g of catalyst at 60°C and times of 6 hours of reaction. It was determined the content of ethyl esters by H-NMR analysis and gas chromatography. It was found that the variable of conversion obtained was 80%, showing a good catalytic activity LaSBA-15 in the transesterification of vegetable oils via ethylic route

Uso da glicerina oriunda da síntese do biodiesel em sistemas microemulsionados visando aplicação de herbicidas

The program PROBIODIESEL from the Ministry of Science and Technology has substantially increased glycerine, obtained as a sub-product of biodiesel production process, making it necessary to seek alternatives for the use of this co-product. On the other hand, herbicides although play a role of fundamental importance in the agricultural production system in force, have been under growing concern among the various segments of society because of their potential environmental risk. In this work, we used glycerin in microemulsion systems for application of herbicides, to improve efficiency and lower environmental pollution caused by the loss of those products to the environment. To obtain the systems of microemulsinados were used Unitol L90 NP and Renex 40 as surfactants, butanol as co-surfactant, coconut oil as oil phase and aqueous phase as we used solutions of glycerin + water. Through the determination of phase diagrams, the microemulsion region was found in the system E (L90 Unitol, coconut oil and glycerin + water 1:1). Three points were chosen to the aqueous phase rich in characterization and application in the solubilization of glyphosate and atrazine. Three experiments were performed in Horta, Department of Plant Sciences, Plant Science Sector, UFERSA, Mossoró-RN. The first experiment was conducted in randomized complete blocks with 20 treatments and four replications. The treatments consisted of five doses of the herbicide glyphosate (0.0, 0.45, 0.9, 1.35 and 1.8 L ha-1) diluted with four sauces: C1, C2, C3 (microemulsions) and C4 (water). The phytotoxicity of Brachiaria brizantha was measured at 7, 14, 28 and 60 DAA (days after application). At 60 DAA, we evaluated the biomass of plants. The second experiment was developed in randomized complete blocks with 20 treatments and four repetitions. The treatments consisted of five doses of the herbicide atrazine (0.0, 0.4, 0.8, 1.6 and 2.4 L ha-1) diluted with four sauces: C1, C2, C3 (microemulsions) and C4 (water). The phytotoxicity on Zea mays and Talinum paniculatum was evaluated at 2, 7, 20 DAA. The experiment III was developed in randomized complete blocks with 16 treatments and three repetitions. The treatments consisted of 16 combinations among the constituents of the microemulsion: Unitol L90 surfactant (0.0, 1.66, 5.0, 15 %) and glycerin (0.0, 4.44, 13.33 and 40.0 %). The phytotoxicity on Zea mays was evaluated at 1, 7 and 14 DAA. At 14 DAA, we evaluated the biomass of plants. The control plants using the microemulsions was lower than in the water due to the poisoning caused by the initial microemulsions in the leaves of the plants, a fact that hinders the absorption and translocation of the herbicide. There was no toxicity in Zea mays plants caused by the herbicide, however, were highly intoxicated by microemulsions. T. paniculatum was better controlled in spraying with the microemulsions, regardless of the dose of the herbicide. The glycerine did not cause plant damage. Higher poisoning the plants are caused by tensoactive Unitol L90 and higher rates occur with the use of higher concentrations of surfactant and glycerin, or microemulsion. The microemulsions used hampered the action of glyphosate in controlling B. brizantha and caused severe poisoning in corn, and these poisonings attributed mainly to the action of surfactant

Novo sistema de aplicação de drogas em cirurgias oftalmológicas

The topical corneal application of antimitotic mitomycin-C (MMC) during refractive surgery is still characterized by a lack of standardization and considerable empirism. For this reason the creation of a system capable of reliable drug delivery represents a beneficial innovation for patients submitted to these procedures. Objective: Elaborate a new MMC delivery system during the transoperatory period of photorefractive keratectomy (PRK) followed by patent application. Methods: The project consists of an in vitro experimental study to create an MMC (0.02%) release system. The drug was impregnated in sterile Whatman® 41 paper filter discs with a diameter of 8 mm. After drying, the discs were applied to antibiogram plates seeded with Staphylococcus epidermidis (American Type Culture Collection ATCC 12228), followed by the addition of a drop of sterile water. At the end of 1 minute, the discs were removed and the plates incubated for 48 hours at 35oC. Mean drop volume in the collyrium flasks was measured using analytical balance weighing. The inhibition halo (mm) was correlated with the MMC impregnated into the disc. After completion of the invention design a patent application was lodged at the National Institute of Industrial Property. Results: The correspondence between MMC-produced inhibition halos indicated that a dose of 16μg was ideal for impregnating into the discs. The mean drop volume obtained from the collyrium flasks was 37.7 μL. A minute after the application of one drop of balanced saline solution, the system released an adequate concentration for PRK surgery. Conclusion: A new MMC delivery system was created for transoperatory application in photorefractive keratectomy (PRK). Publication of the patent application (number PI 0704739-8) gives the authors exclusive intellectual property rights. The study was sponsored by Ophthalmos Indústria e Comércio de Produtos Farmacêuticos S.A. (São Paulo-SP, Brazil) and received the indispensable scientific contribution of researchers from the fields of Pharmacy, Medicine, Biology, Statistics and Law, characterizing the work as multidisciplinary, in accordance with norms established by the Postgraduate Health Sciences Program of the Federal University of Rio Grande do Norte (UFRN)

A aplicação do acordo sobre subsídios e medidas compensatórias pelo estado brasileiro

The Multilateral Trading System has evolved and presented new international mandatory rules to States. Along with the World Trade Organization constitutive treaty, Brazil has incorporated the Agreement on Subsidies and Countervailing Measures (ASCM) in the national legal system. That treaty limits de scope of subsidies concession by governments since this practice can constitute a mechanism of commercial disloyalty, affecting national industrial development in the importing country. At the same time, the multilateral agreement grants defense legitimate instruments to States, among them the possibility of domestically and unilaterally imposing countervailing measures to subsidized products that enter the national territory. Since the issue concerns both international and domestic level in complementary grounds, this research, besides investigating the treaty related obligation, aims at studying the national legal fundaments to ASCM s application by the Brazilian State. Therefore, the essential point resides in the State s conduction of its international trading and also in its available and constitutionally established mechanisms of economic intervention. State s regulating power reveals itself as a fundamental prerogative to succeed in the internalization of international agreement s requirements in the domestic legal system, which represents a basic prerequisite to the implementation of countervailing measures. Once the whole normative outlines are apprehended, this study shall scan the administrative process of trading defense main elements, along with the means of controlling public administration acts. The action taken by the public organs that directly intervene in foreign trade shall be analyzed as well, so as to enable reasoning if the unilateral application of countervailing duties by the Brazilian State is happening on legitimacy grounds

Aplicação da metodologia seis sigma em uma empresa de médio porte do setor têxtil

The Six Sigma methodology has received considerable attention in the last two decades. This is due to its great potencial to reduce processes variability, through the use of accurate data, facts and statistical techniques. The methodology seeks to improve the quality of products and services, maximizing the company s financial performance. Specifically, its implementation and results in medium-sized textile enterprises is unknow, although there are signs that the methodology can be applied with success. Considering this scenario, the goal of this research is to describe the application of the Six Sigma methodology in a médium-sized textile company specialized in the production of male shirts in the satate of Rio Grande do Norte, Brazil. First, we present a literature review, seeking to highlight the themes of quality, Six Sigma and its methodology for improvement. Then, we show the implementation of the project selected, depicting the steps and procedures that must be performed. The results confirm the efficiency of Six Sigma in providing significant gains to companies. It is observed substantial improvements in the speed of product development and the flexibility of the parts produced, reducing the process lead time from 12.5 to 6.2 days, which means a performance improvement of over 50%. This leads also to cultural and behaviour change, creating motivation for implementation of new projects and a continuous search for knowledge

Desenvolvimento de um modelo de gestão do conhecimento para a melhoria do processo de desenvolvimento de produtos

The knowledge management has received major attention from product designers because many of the activities within this process have to be creative and, therefore, they depend basically on the knowledge of the people who are involved in the process. Moreover, Product Development Process (PDP) is one of the activities in which knowledge management manifests in the most critical form once it had the intense application of the knowledge. As a consequence, this thesis analyzes the knowledge management aiming to improve the PDP and it also proposes a theoretical model of knowledge management. This model uses five steps (creation, maintenance, dissemination, utilization and discard) through the verification of the occurrence of four types of knowledge conversion (socialization, externalization, combination and internalization) that it will improve the knowledge management in this process. The intellectual capital in Small and Medium Enterprises (SMEs) managed efficiently and with the participation of all employees has become the mechanism of the creation and transference processes of knowledge, supporting and, consequently, improving the PDP. The expected results are an effective and efficient application of the proposed model for the creation of the knowledge base within an organization (organizational memory) aiming a better performance of the PDP. In this way, it was carried out an extensive analysis of the knowledge management (instrument of qualitative and subjective evaluation) within the Design department of a Brazilian company (SEBRAE/RN). This analysis aimed to know the state-of-the-art of the Design department regarding the use of knowledge management. This step was important in order to evaluate in the level of the evolution of the department related to the practical use of knowledge management before implementing the proposed theoretical model and its methodology. At the end of this work, based on the results of the diagnosis, a knowledge management system is suggested to facilitate the knowledge sharing within the organization, in order words, the Design department