Medição da densidade óssea através de ondas eletromagnéticas e classificação por MVS

This work holds the purpose of presenting an auxiliary way of bone density measurement through the attenuation of electromagnetic waves. In order to do so, an arrangement of two microstrip antennas with rectangular configuration has been used, operating in a frequency of 2,49 GHz, and fed by a microstrip line on a substrate of fiberglass with permissiveness of 4.4 and height of 0,9 cm. Simulations were done with silica, bone meal, silica and gypsum blocks samples to prove the variation on the attenuation level of different combinations. Because of their good reproduction of the human beings anomaly aspects, samples of bovine bone were used. They were subjected to weighing, measurement and microwave radiation. The samples had their masses altered after mischaracterization and the process was repeated. The obtained data were inserted in a neural network and its training was proceeded with the best results gathered by correct classification on 100% of the samples. It comes to the conclusion that through only one non-ionizing wave in the 2,49 GHz zone it is possible to evaluate the attenuation level in the bone tissue, and that with the appliance of neural network fed with obtained characteristics in the experiment it is possible to classify a sample as having low or high bone density

PLANFOR: política compensatória para a inclusão na informalidade?

Study about the national politics on the professional education, under responsibility of the brazilian Work Department in 1990 years. Purposes to apprehend the results of the actions of the professional education in a basic level, offered by the National Plan of the worker qualification ( PLANFOR ), as well as the effects on the assisted exits, starting from the experience appreciated on the Plan of Qualification developed in the state of Maranhão between 1996 to 2000. It adopts a theoretical-methodological conception by an ontological nature, if being worth of categories as the one of totality and of mediation that together, makes possible the apprehension of a dialectical movement that happens among the analysis object, the professional education politics in a basic level, performed by PLANFOR and your context, the underdevelop and heterogeneous Brazilian capitalism and the consequent job market generalized precarious and informal, making possible that the reality investigated become to understood rationally. This paper uses the indirect documentation technique, instruments of the bibliographical research and documental research. This study is based on those that aren´t part of PLANFOR, qualified by professional education courses in basic level,they didn't get to be inserts at the formal job market, just occupying precarious occupations in the informal job market. Aims to presents and discusses the productive process and your restructuring globally in progress. It focuses at the impacts on the workers, the precariousness of the work that appears like a new phenomenon calls new informality. Talks about the particularity process of productive restructuring assumed in Brazil highlights, showing that the informality, was always a structural phenomenon in the country. Discusses about the professional qualification in the contemporary capitalism, specifying some of your theses. Shows in a historical view the process of appearance of the employment notions and competence, and the influence that it exercised on the reforms of the basic and professional education, as well as the implications of both in the politics of professional education in the country. Rescues the process of creation of PLANFOR, your official formulations and your organized bases, starting from the second half of the 1990 decade. Shows yet the continuos changes in the job market of Maranhão state, for after, starting from the reports expresses at the Plans of Qualification from the state, elaborated by the Group of Evaluation and Studies of the Poverty and the Politics addressed to the poverty from the Master degree Program in Public Politics, from the Federal University of Maranhão, analyzing the acting of PLANFOR in the State, your probable deficiencies, as results the changes verified in the conditions of occupation and the gains of the exits from the professional education courses in basic level

Redes neurais artificiais no ambiente de redes industriais foundation fieldbus usando blocos funcionais padrões

Industrial automation networks is in focus and is gradually replacing older architectures of systems used in automation world. Among existing automation networks, most prominent standard is the Foundation Fieldbus (FF). This particular standard was chosen for the development of this work thanks to its complete application layer specification and its user interface, organized as function blocks and that allows interoperability among different vendors' devices. Nowadays, one of most seeked solutions on industrial automation are the indirect measurements, that consist in infering a value from measures of other sensors. This can be made through implementation of the so-called software sensors. One of the most used tools in this project and in sensor implementation are artificial neural networks. The absence of a standard solution to implement neural networks in FF environment makes impossible the development of a field-indirect-measurement project, besides other projects involving neural networks, unless a closed proprietary solution is used, which dos not guarantee interoperability among network devices, specially if those are from different vendors. In order to keep the interoperability, this work's goal is develop a solution that implements artificial neural networks in Foundation Fieldbus industrial network environment, based on standard function blocks. Along the work, some results of the solution's implementation are also presented

Envelhecimento ambiental acelerado em PRF a base de tecidos híbridos kevlar/vidro: propriedades e instabilidade estrutural

There are a number of damaging mechanisms that various materials can suffer in service. However, when working with polymer composite materials, this is something that requires analysis, especially when exposed to adverse environmental conditions. Thus, the objective of the present thesis is the study of the direct influence of environmental aging and the form of hybridization of the reinforcement woven on the structural stability, surfacedegradation and fracture process of polymer composites laminates. For this, the development of two polymer composite laminates was necessary, where one of them was reinforced with a bi-directional woven with hybrid strandsofkevlar-49/glass-Efibers, and the other also with a bi-directionalwoven, however with weft and warpformed of alternating strandsof Kevlar-49 fibers and glass-E fiber The reinforcementwoven are industrially manufactured. Both laminates use a polyester resin as a matrixand are made up of four layers each. All laminates were industrially prepared by the hand lay-up method of manufacturing. To do this, test specimens were manufactured of the respective laminates and submitted to environmental aging accelerated through the aging chamber. They were exposed to alternating cycles of UV radiation and moisture (heated steam) for a standard defined period. At the end of the exposure period the specimens were subjected to mechanical tests of uniaxial tensile and bending in three points and to the characterizationsof the fracture and surface deterioration. In addition, they were submitted to a structural degradation assessment by the measurement of mass variation technique (MMVT) and the measurement of thickness variation technique (MTVT), this last technique being developed in this thesis. At the end of the analysis it was observed that the form of hybridization of the reinforcement woven and the aging process directly influence with losses or gain in mechanical properties, with losses in the structural degradation and in the formation and propagation of damage mechanism of the developedcomposite laminates

Sistemas de automação e supervisão do laboratório de avaliação dos processos de medição de vazão e BSW

During a petroleum well production process, It is common the slmultaneous oil and water production, in proportion that can vary from 0% up to values close to 100% of water. Moreover, the production flows can vary a lot, depending on the charaeteristies of eaeh reservoir. Thus being, the meters used in field for the flow and BSW (water in the oil) measurement must work well in wide bands of operation. For the evaluation of the operation of these meters, in the different operation conditions, a Laboratory will be built in UFRN, that has for objective to evaluate in an automatic way the processes of flow and BSW petroleum measurement, considering different operation conditions. The good acting of these meters is fundamental for the accuracy of the measures of the volumes of production liquid and rude of petroleum. For the measurement of this production, the petroleum companies use meters that should indicate the values with tha largast possible accuracy and to respect a series of conditions and minimum requirements, estabelished by the united Entrance ANP/INMETRO 19106/2000. The laboratory of Evafuation of the Processes of Measurement of Flow and BSW to be built will possess an oil tank basically, a tank of water, besides a mixer, a tank auditor, a tank for separation and a tank of residues for discard of fluids, fundamental for the evaluation of the flow metars and BSW. The whole process will be automated through the use of a Programmable Logicat Controller (CLP) and of a supervisory system.This laboratory besides allowing the evaluation of flow meters and BSW used by petroleum companies, it will make possible the development of researches related to the automation. Besides, it will be a collaborating element to the development of the Computer Engineering and Automation Department, that it will propitiate the evolution of the faculty and discente, qualifying them for a job market in continuous growth. The present work describes the project of automation of the laboratory that will be built at of UFRN. The system will be automated using a Programmable Logical Controller and a supervisory system. The programming of PLC and the screens of the supervisory system were developed in this work

Desenvolvimento e avaliação de padrão de torque para calibração de torquímetros em três faixas de medição

The continuous development of instruments and equipment used as tools or torque measurement in the industry is demanding more accurate techniques in the use of this kind instrumentation, including development of metrological characteristics in torque measurement. The same happens with the needs in calibration services. There is a diversity of methods of hand torque tools in the market with different measuring range but without complaining with technical standards in terms of requirements of quality and reliability. However, actually there is no choice of a torque measuring standard that fulfils, with low cost, the needs for the calibration of hand torque tools in a large number of ranges. The objective of this thesis is to show the development and evaluation of a torque measuring standard device with a conception to allow the calibration of hand torque tools with three levels of torque with an single instrument, promoting reduction of costs and time in the calibration, also offering reliability for the evaluation of torque measuring instrument. To attend the demand in the calibration of hand torque tools it is necessary that the calibration laboratories have a big collection of torque measuring standards, to fulfills the needs of the costumer, what is very costly. The development of this type of torque measuring standard revealed a viable technique and economically making possible the calibration of hand torque tools in different nominal ranges through a single measurement system versatile, efficient and of easy operation

Estudo do potencial da técnica de nanossísmica para o monitoramento de hidrofraturamento em reservatórios de hidrocarbonetos

Hydraulic fracturing is an operation in which pressurised fluid is injected in the geological formation surrounding the producing well to create new permeable paths for hydrocarbons. The injection of such fluids in the reservoir induces seismic events. The measurement of this reservoir stimulation can be made by location these induced microseismic events. However, microseismic monitoring is an expensive operation because the acquisition and data interpretation system using in this monitoring rely on high signal-to-noise ratios (SNR). In general, the sensors are deployed in a monitoring well near the treated well and can make a microseismic monitoring quite an expensive operation. In this dissertation we propose the application of a new method for recording and location of microseismic events called nanoseismic monitoring (Joswig, 2006). In this new method, a continuous recording is performed and the interpreter can separate events from noise using sonograms. This new method also allows the location of seismic sources even when P and S phases onsets are not clear like in situations of 0 dB SNR. The clear technical advantage of this new method is also economically advantageous since the sensors can potentially be installed on the surface rather than in observation well. In this dissertation field tests with controlled sources were made. In the first test small explosives using fire works at 28 m (slant distances) were detected yealding magnitudes between -2.4 ≤ ML ≤ -1.6.. In a second test, we monitored perforation shots in a producing oil field. In this second test, one perforation shot was located with slant distances of 861 m and magnitude 2.4 ML. Data from the tests allow us to say that the method has potential to be used in the oil industry to monitor hydrofracture