Estudo de sistemas vítreos para infiltração em alumina

The system in-Ceram Alumina, produced by VITA, consists in a technique of prepare of a substructure of ceramics to dental crowns. First burning is made in the alumina decanted by slip casting process under a stone die that reproduces the tooth prepared to receive a crown. In a second burning, alumina is infiltrated by vitreous system, giving to this set a high mechanic resistance. In this work, it s made a study of the composition of a new infiltrating material more used nowadays, giving to alumina desirable mechanics proprieties to its using like substructure of support to ceramic s crown used in the market today. The addition of Lanthanum oxide (frit A) and calcium oxide (frit B) was made in attempt to increase the viscosity of LZSA and to reduce fusion temperature. The frits were put over samples of alumina and took to the tubular oven to 1400ºC under vacuum for two groups (groups 1 and 2). For another two groups (groups 3 and 4) it was made a second infiltration, following the same parameters of the first. A fifth group was utilized like group of control where the samples of pure alumina were not submitted to any infiltrating process. Glasses manifested efficient both in quality and results of analysis of mechanic resistance, being perfectly compatible with oral environment in this technical requisite. The groups that made a second infiltration had he best results of fracture toughness, qualify the use in the oral cavity in this technical question. The average of results achieved for mechanic resistance to groups 1, 2, 3, 4 and 5 were respectively 98 MPa, 90 MPa, 144 MPa, 236 MPa and 23 MPa

Estudo da substituição de agregados miúdos naturais por pó de pedra em concreto de cimento portland

The sharp consumption of natural resources by the construction industry has motivated numerous studies concerning the application of waste to replace partially or fully, some materials, such as aggregates, thereby reducing the environmental impact caused by the extraction of sand and crushing process. The application of stone dust from crushing process arising as an aggregate for the production of Portland cement concrete is a viable alternative in view of the high cost of natural sands, in addition to the environmental damage which causes its operation to the environment. The stone dust has reduced cost compared to natural sand because it is produced in the beds of their own quarries, which are usually located close to major urban centers. This study examined the feasibility of using stone dust from the crushing of rock gneisses in the state of Bahia, replacing natural quartz sand. In the development of scientific study was conducted to characterize physical and chemical raw materials applied and molded cylindrical specimens , using as reference values Fck 20, Fck 25 and Fck 30 MPa ( resistance characteristic of the concrete after 28 days) in following compositions stone powder: 10%, 30%, 50 %, 100% and 100% with additive. The specimens were cured and subjected to the tests of compressive strength and water absorption, then the samples were subjected to the tests of X-ray diffraction and scanning electron microscopy. The results obtained showed that the composition with 10% stone powder showed the best results regarding the physical and mechanical tests performed, confirming the reduction in compressive strength and increased water uptake increased as the content of the powder stone in the concrete composition

Avaliação do efeito da adição de resíduo de borracha de pneu e brita calcária na formulação de compósitos cimentíceos

Researches have shown that the introduction of rubber in concrete improves the features of its deformability, as well as contributes to environmental disposal of waste generated in the tire retreading process. Furthermore, there is a high availability of limestone within RN and CE country. Ignorance about this stone, does not allow its wide use as aggregate, leaving, this abundant supply idle. A composite of limestone gravel, with proportions of tire rubber waste which could be used as concrete would be an alternative to concrete for low applications. Therefore, this research aims to evaluate the characteristics of concrete containing limestone gravel and proportions of little aggregate replacement (sand) by tire rubber waste. To this goal, the material components of the concrete were characterized, concrete specimens with limestone gravel were made, from the dash 1.0: 2.5: 3.5, varying the water/cement ratio, and inserting a commercial plasticizer, without a proportion of residue, known as reference. From this, concrete with and without the presence of the additive in the same proportions were chosen, as well as these with the use of granite gravel, for being the most used. Selected the references, to these, replacements of little aggregate (sand) were added replaced by rubber waste from the tire retreading process, treated with 1M NaOH in proportions from 5.0 to 20.0 % by mass, cured and exposed to the semiarid environment. The results indicate the possibility of using limestone gravel in the concrete composition with workability correction using plasticizer. There was a decrease in the mechanical properties of the concrete with increments of waste rubber, but there is an improvement in toughness and deformability of the composite, which makes it interesting for the construction of non-structural concrete floors, as well as, the rubber waste delayed the hardening process, continuing to gain resistance after 28 days

Fatores litogênicos em pacientes com litíase urinária de Fortaleza, Ceará

Lithiasis is considered a public health issue due to its high prevalence and rates of recurrence. Objective: To identify risk factors for lithiasis in kidney stone patients from Fortaleza, Brazil. In the first stage of the study, the medical records of 197 patients with urinary lithiasis covering the period 1996 2006 were analyzed with regard to clinical and metabolic data. In the second stage, 340 kidney stones were submitted to morphological examination under 10x magnification. According to the external morphology and the cut surface, the stones were classified as pure or mixed, and major and minor components were identified. In addition, the stone fragments of 25 patients treated with lithotripsy were submitted to morphological analysis. In the third stage, a subsample of 50 stones was used in a double-blind comparison of morphological and chemical findings. Results were expressed as concordant, partly concordant (discordant for minor components) or discordant (discordant for major components). The average age of first symptoms was 35.8±13.3 years, with no significant difference between the genders. The male/female ratio was 1:1.7. Recurrence was reported in 53.3% of cases. The main metabolic changes observed were hypernatriuria (80.7%), hypercalciuria (48.7%), low urine volume (43.7%), hyperoxaluria (30.5%) and hyperuricosuria (17.3%). Pure stones represented 34.7% of the total sample of 340 stones. The most common route of elimination was spontaneous for pure stones (49.1%) and surgical for mixed stones (50.5%). Pure stones consisted most frequently of calcium oxalate (OxCa) (59.3%) and uric acid (UA) (23.7%), the former prevalent in women, the latter prevalent in men. The most frequently observed component in mixed stones was OxCa (67.1%), followed by carbapatite (11.2%) and struvite (7.9%). The main components were OxCa and UA for men, and carbapatite and struvite for women. Nearly half (48%) the 25 analyzed fragments were pure, consisting of calcium oxalate dihydrate (COD) (56%), calcium oxalate monohydrate (COM) (48%), phosphate (32%) and UA (20%). Four patients (16%) had infectious stones. In the chemical analysis of the subsample of 50 stones, the most 64 frequently observed major components were calcium (70%), oxalate (66%), ammonium (56%), urate (28%) and carbonate (24%). In the morphological analysis, the main components were calcium and magnesium phosphate (32%), COM (24%), UA (20%), COD (18%) and cystine (6%). Morphological and chemical findings were totally concordant for 38% of the stones, partly concordant in 52% and discordant in 10%. Conclusion: The risk factors for lithiasis in kidney stone patients from Fortaleza (Brazil) were hyperoxaluria, hypercalciuria with or without hypernatriuria, hyperuricosuria and low urine volume

Abordagem inicial de lesões mamárias por biopsia helicóide: estudo experimental

OBJECTIVE: Evaluating the kit-Bh performance in carrying out of breast biopsies. METHODS: They were randomly selected a sample of 30 patients with breast cancer undergoing mastectomy, based on the results of a pilot study from February 2008 to April 2010. They were excluded women with had not palpable, stone-hard consistency tumors, previous surgical manipulation or that contains liquid. Using the helicoid biopsy Kit (kit Bh) and an equipment Core biopsy with cannula and needle and 14 gauge respectively, it was collected a fragment of sound equipment in the area and in tumors in each specimen, totaling 120 fragments for histological study. For data analysis, it was defined a 95% confidence level and used the SPSS-13 version, the Kappa index and the parametric Student t test. RESULTS: Mean age of patients was 51.6 years (± 11.1 years). The infiltrating ductal carcinoma showed a higher incidence, 26 cases (86.7%). The Core biopsy had a sensitivity of 93.3%, specificity of 100% and accuracy 96.7%, while the helicoid biopsy had a sensitivity of 96.7%, specificity of 100% and accuracy 98.3%. By comparing the histology of tumors and the fragments of biopsies, there was high degree of agreement in diagnoses (kappa of 0.93 with p <0.05) CONCLUSION: Both devices provided the histological diagnosis of lesions with high accuracy. Results of this study showed that the helicoid biopsy is a reliable alternative in 22 the preoperative diagnosis of breast lesions. Further studies in vivo better will define the role of Kit Bh in the diagnosis of these lesions