Extração e análise da fração lipídica da microalga monoraphidium sp., síntese e caracterização do seu biodiesel

The cultivation of microalgae biomass in order to produce biodiesel arises as an extremely promising aspect, in that the microalgae culture includes short cycle of reproduction, smaller areas for planting and residual biomass rich in protein content. The present dissertation evaluates the performance and features, through spectrometry in the region of infrared with transformed Fourier (FTIR) and spectrometry in the region of UVvisible (UV-Vis), of the extracted lipid material (LM) using different techniques of cell wall disruption (mechanical agitation at low and at high spin and agitation associated with cavitation). The technique of gas chromatography (GC) brought to light the success of alkaline transesterification in the conversion of oil into methyl monoesters (MME), which was also analyzed by spectroscopic techniques (FTIR, proton magnetic resonance (1H NMR) and carbon (13C NMR). Through thermogravimetric analysis (TGA) were analyzed the lipid material (LM), biodiesel and the microalgae biomass. The method which provided the best results concerning the efficiency in extraction of the LP of Monoraphidium sp. (12,51%) was by mechanical agitation at high spin (14 000 rpm), for 2 hours being the ideal time, as shown by the t test. The spectroscopic techniques (1H NMR, 13C NMR and FTIR) confirmed that the structure of methyl monoesters and the chromatographic data (CG) revealed a high content of saturated fatty acid esters (about 70%) being the major constituent eicosanoic acid (33,7%), which justifies the high thermal stability of microalgae biodiesel. The TGA also ratified the conversion rate (96%) of LM into MME, pointing out the quantitative results compatible with the values obtained through GC (about 98%) and confirmed the efficiency of the extraction methods used, showing that may be a good technique to confirm the extraction of these materials. The content of LM microalgae obtained (12,51%) indicates good potential for using such material as a raw material for biodiesel production, when compared to oil content which can be obtained from traditional oil for this use, since the productivity of microalgae per hectare is much larger and requires an extremely reduced period to renew its cultivation

Extração, caracterização e avaliação bioativa do extrato de Rumex acetosa

Studies show the great influence of free radicals and other oxidants as responsible for aging and degenerative diseases. On the other hand, the natural phenolic compounds has shown great as antioxidants to inhibit lipid peroxidation and lipoxygenase in vitro. Among these, is highlighted trans-resveratrol ( 3,5,4 `- trihydroxystilbene ) phenolic compound , characterized as a polyphenol stilbene class. The vegetables popularly known as "Azedinha" (Rumex Acetosa) has trans-resveratrol in its composition and from this, the present work aimed to study on the supercritical extraction and conventional extraction (Soxhlet and sequential) in roots of Rumex Acetosa, evaluating the efficiency of extractive processes, antioxidant activity, total phenolic content and quantification of trans-resveratrol contained in the extracts. Extractions using supercritical CO2 as solvent, addition of co-solvent (ethanol) and were conducted by the dynamic method in a fixed bed extractor. The trial met a 23 factorial design with three replications at the central point, with the variable reply process yield and concentration of trans-resveratrol and pressure as independent variables, temperature and concentration of co-solvent (% v/v). Yields ( mass of dry extract / mass of raw material used ) obtained from the supercritical extraction ranged from 0,8 to 7,63 % , and the best result was obtained at 250 bar and 90 °C using the co-solvent 15% ethanol (% v/v). The value was calculated for YCER a flow rate of 1,0 ± 0,17 g/min resulting in 0,0469 CO2 ( g solute / g solvent ). The results of the mass yield varied between conventional extractions 0,78 % ( hexane) and 9,97 % (ethanol). The statistical model generated from the data of the concentration of trans-resveratrol performed as meaningful and predictive for a 95% confidence. GC analysis on HPLC (High Performance Liquid Chromatography), transresveratrol was quantified in all extracts and concentration values ranged between 0,0033 and 0,42 ( mg / g extract) for supercritical extracts and between 0,449 and 17,046 (mg / g extract) to conventional extractions and therefore, the Soxhlet extraction with ethanol for more selective trans-resveratrol than the supercritical fluid. Evaluation of antioxidant (radical method to sequester 2,2- diphenyl-1- picryl - hydrazyl - DPPH) the supercritical extracts resulted in EC50 values (concentration effective to neutralize 50% of free radicals) of between 7,89 and 18,43 mg/mL , while resulting in a Soxhlet extraction with EC50 values in the range of 6,05 and 7,39 mg/mL. As for quantification of the phenolic compounds (Method Spectrophotometer Folin-Ciocalteau) the supercritical extracts resulted in values between 85,3 and 194,79 mg GAE / g extract, whereas values derived from the Soxhlet extract resulted in values between 178,5 and 237,8 mg GAE / g extract. The high antioxidant activity can not be attributed solely to the presence of phenolic compounds, but the presence of other antioxidants in the existing Rumex acetosa

Extração supercrítica do óleo de linhaça: construção do extrator, estudo de parâmetros de processo, avaliação química e antioxidante do produto

The aim of the present study was to extract vegetable oil from brown linseed (Linum usitatissimum L.), determine fatty acid levels, the antioxidant capacity of the extracted oil and perform a rapid economic assessment of the SFE process in the manufacture of oil. The experiments were conducted in a test bench extractor capable of operating with carbon dioxide and co-solvents, obeying 23 factorial planning with central point in triplicate, and having process yield as response variable and pressure, temperature and percentage of cosolvent as independent variables. The yield (mass of extracted oil/mass of raw material used) ranged from 2.2% to 28.8%, with the best results obtained at 250 bar and 50ºC, using 5% (v/v) ethanol co-solvent. The influence of the variables on extraction kinetics and on the composition of the linseed oil obtained was investigated. The extraction kinetic curves obtained were based on different mathematical models available in the literature. The Martínez et al. (2003) model and the Simple Single Plate (SSP) model discussed by Gaspar et al. (2003) represented the experimental data with the lowest mean square errors (MSE). A manufacturing cost of US$17.85/kgoil was estimated for the production of linseed oil using TECANALYSIS software and the Rosa and Meireles method (2005). To establish comparisons with SFE, conventional extraction tests were conducted with a Soxhlet device using petroleum ether. These tests obtained mean yields of 35.2% for an extraction time of 5h. All the oil samples were sterilized and characterized in terms of their composition in fatty acids (FA) using gas chromatography. The main fatty acids detected were: palmitic (C16:0), stearic (C18:0), oleic (C18:1), linoleic (C18:2n-6) and α-linolenic (C18:3n-3). The FA contents obtained with Soxhlet dif ered from those obtained with SFE, with higher percentages of saturated and monounsaturated FA with the Soxhlet technique using petroleum ether. With respect to α-linolenic content (main component of linseed oil) in the samples, SFE performed better than Soxhlet extraction, obtaining percentages between 51.18% and 52.71%, whereas with Soxhlet extraction it was 47.84%. The antioxidant activity of the oil was assessed in the β-carotene/linoleic acid system. The percentages of inhibition of the oxidative process reached 22.11% for the SFE oil, but only 6.09% for commercial oil (cold pressing), suggesting that the SFE technique better preserves the phenolic compounds present in the seed, which are likely responsible for the antioxidant nature of the oil. In vitro tests with the sample displaying the best antioxidant response were conducted in rat liver homogenate to investigate the inhibition of spontaneous lipid peroxidation or autooxidation of biological tissue. Linseed oil proved to be more efficient than fish oil (used as standard) in decreasing lipid peroxidation in the liver tissue of Wistar rats, yielding similar results to those obtained with the use of BHT (synthetic antioxidant). Inhibitory capacity may be explained by the presence of phenolic compounds with antioxidant activity in the linseed oil. The results obtained indicate the need for more detailed studies, given the importance of linseed oil as one of the greatest sources of ω3 among vegetable oils

Caracterização físico-química e efeitos de frações polissacarídicas da alga amansia multifida na coagulação, inflamação, radicais livres e viabilidade celular

Galactans are polysaccharides sulfated present in the cell wall of red algae. Carrageenans are galactans well known in the food industry as gelling polysaccharides and for induce inflammatory process in rodents as animal model. The extraction of polysaccharides from A. multifida has been carried out by proteolysis and precipitation in different volumes of acetone, which produced three fractions (F1, F2, and FT). Chemical and physical analyses revealed that these fractions are sulfated galactan predominantly. Results of the antioxidant activity assays showed that all of these fractions have antioxidant activity and that was associated with sulfate content of the analysis of reducing power and total antioxidant capacity. However, these fractions were not effective against lipid peroxidation. The fraction FT presented higher activity on the APTT test at 200 μg (> 240 s). The assessment of the hemolytic activity showed that the FT fraction has the best activity, increasing lyses by the complement system to 42.3% (50 μg) (p< 0,001). The fraction FT showed the best yield, anticoagulant and hemolytic activity between the three fractions and therefore it was choose for the in vivo studies. The Inflammation assessment using the FT fraction (50 mg / kg MB) showed that the cellular migration and the IL-6 production increased 670.1% (p< 0,001) and 531.8% (p< 0,001), respectively. These results confirmed its use as an inflammation inducer in animal model. Cytotoxicity assay results showed that all fractions have toxic effects on 3T3 and HeLa cells after exposition of 48 hours, except when 100 μg for both F1 and FT were used. These results arise the discussion whether these polysaccharides it should be used as additive in foods, cosmetics and medicines.

Extração, caracterização estrutural e atividades farmacológicas do olginato obtido da alga marrom Lobophora variegata (Lamouroux) Oliveira Filho, 1977

The alginic acid or alginates are acidic polysaccharides found in brown seaweed widely used in food, cosmetic, medical and pharmaceutical industry. This paper proposes the extraction, chemical characterization and verification of the pharmacological activities of brown seaweed variegata Lobophora . The alginate was extracted from the seaweed Lobophora variegata and part was sulphated for comparative purposes. The native extract showed 42% total sugar, 65% uronic acid, 0,36 % protein and 0% of sulfate, while the sulfate showed 39% , 60%, 0.36% and 27,92 % respectively. The presence of a sulfate group may be observed by the metachromasia with toluidine blue in electrophoresis system and characteristic vibration 1262,34 cm-1 in infrared spectroscopy connections assigned to S = O. We observed the formation of films and beads of native alginate, where more concentrated solution 6% resulted in a thicker and more consistent film. Native alginate showed proliferative activity at concentrations (25 and 50 mcg), (50 mg) and (100 mg) in 3T3 cell line in 24h, 48h and 72h, respectively , as the sulfated (100 mg) in 24 . Also showed antiproliferative or cytotoxic activity in HeLa cells of strain, (25 and 100 mg), (25 and 100 mg) and (25, 50 and 100 mg), to native, now for the sulfate concentrations (100 mg) in 24 (25, 50 and 100 mg) in 48 hours, and (50 and 100 mg ) 72h. For their antioxidant activity, the sulfated alginates have better total antioxidant activity reaching 29 % of the native activity while 7.5 % of activity . For the hydroxyl radical AS showed high inhibition ( between 77-83 % ) in concentrations, but the AN surpassed these numbers in the order of 78-92 % inhibition. The reducing power of AN and AS ranged between 39-82 % . In the method of ferric chelation NA reached 100 % chelating while the AS remained at a plateau oscillating 6.5%. However, in this study , we found alginates with promising pharmacological activities, to use in various industries as an antioxidant / anti-tumor compound

Estudo da adição do resíduo proveniente da extração de minério de ferro em argilas do Rio Grande do Norte

The mining industry is responsible for the generation of waste from their natural process of extraction. The mining impacts in urban areas are of special importance due to the high urban occupation, which are exacerbated due to the proximity of the mined areas and populated areas. Some solutions to wastedisposal have the potential to significantly reduce the environmental risks and liabilities, but represent higher costs in the stages of deployment and operation. The addition of mining waste as raw material in the development of commercial products reduces the environmental impacts, transforming the waste into a positive element in the generation of employment and income. This thesis studies the incorporation of waste iron ore in two clays, one from the ceramic industry of the City of Natal and the other from the ceramic industry of the Seridó Region, both in the State of Rio Grande do Norte, Brazil. Percentages of iron ore waste of 5%, 10% , 15%, 20%, 25% and 30% were used in the tested ceramic matrix. The two clays and the iron ore waste used as part of this investigation were characterized by X-ray diffraction tests, X-ray fluorescence tests, differential thermal analysis, thermogravimetric analysis and dilatometric analysis. The samples were sintered under temperatures of 850 °C, 950 °C and 1050°C at a heating rate of 5 °C/min with isotherms of two hours. The following tests were performed with the samples: linear shrinkage, water absorption, apparent porosity, apparent density, mass loss in fire and bending resistance in order to obtain their physical and mechanical properties. An amount of 5% of waste iron ore in the matrix clay at a temperature of 850 0C resulted in na increase of about 65% in the tensile strength of the clay samples from the Natal ceramic industry. A linear shrinkage of only 0.12% was observed for the samples, which indicates that the physical properties of the final product were not influenced by the addition of the waste

Extração de boro de água produzida sintética por sistema microemulsionado

Boron is a semi-metal present in certain types of soils and natural waters. It is essential to the healthy development of plants and non-toxic to humans, depending on its concentration. It is used in various industries and it s present in water production coming from oil production. More specifically in Rio Grande do Norte, one of the largest oil producers on shore of Brazil, the relationship water/oil in some fields becomes more than 90%. The most common destination of this produced water is disposal in open sea after processing to meet the legal specification. In this context, this research proposes to study the extraction of boron in water produced by microemulsion systems for industrial utilization. It was taken into account the efficiency of extraction of boron related to surfactant (DDA and OCS, both characterized by FT-IR), cosurfactant (butanol and isoamyl alcohol), organic phase (kerosene and heptanes) and aqueous phase (solution of boron 3.6 ppm in alkaline pH). The ratio cosurfactant/ surfactant used was four and the percentage of organic phases for all points of study was set at 5%. It was chosen points with the highest percentage of aqueous phase. Each system was designed for three points of different compositions in relation to the constituents of a pseudoternary diagram. These points were chosen according to studies of phase behavior in pseudoternary diagrams made in previous studies. For this research, points were chosen in the Winsor II region. The excess aqueous solution obtained in these systems was separated and analyzed by ICP OES. For the data set obtained, the better efficiency in the extraction of boron was obtained using the system with DAC, isoamyl alcohol and heptanes, which extracted 49% in a single step. OCS was not viable to the extraction of boron by microemulsion system in the conditions defined in this study

Extração de metais (K, Mg, Ba, Ca, Cr, Mn, Li, Fe) de água produzida utilizando sistema microemulsionado

The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation

Processo de desidratação da alga Gracilaria birdiae beneficiada em laboratório e artesanalmente: análise da atividade antioxidante e composição centesimal

The main aim of this study was to compare the procedure for dehydration of Gracilaria birdiae prepared handmade and laboratory, collected in the northern coast of Rio Grande do Norte. The sample was collected in the Rio do Fogo beach in march 2009. The sample collected followed by two processing, the first the material prepared in laboratory was air-dried at 50°C for 24 hours in air-flow oven. The second the handmade sample was air-dried on the sun during three days. The extract was prepared in three different solvents: ethanol, hydroethanol and water, resulting in ethanol, hidroethanol and aqueous extracts from handmade and laboratory sample. In according with results only the ethanol extract was fractionated yielding the fractions hexane, dichloromethane and ethyl acetate fractions. The different process to obtain Gracilaria birdiae resulted in the samples with different shades. The soluble solids content was higher in the laboratory sample. The chemical composition the both samples were characterized by presenting a considerable amounts of carbohydrates, with amior percentage protein and ash, respectively, in the handmade and laboratory sample. In two samples showed a low content of lipids and the lipid profile showed a higher proportion of monounsaturated fatty acids, with the absence polyunsaturated handmade sample. The phytochemical screening by chemical reactions showed the presence of flavonoids, tannins, alkaloids and saponins the laboratory sample, presenting a greater diversity of bioactive compounds. Through of the analysis by thin layer chromatography was possible to identify the phytosterols β-sitosterol and stigmasterol the both samples, also suggest the presence of β-carotene and chlorophyll α the laboratory sample. The levels of total phenolics and flavonoids were more significant in the ethanol extract of the laboratory sample. The in vitro lethality showed that extracts of the laboratory sample and handmade from 125 to 500 μg/ mL, respectively, were highly lethal. In the evaluation of antioxidant capacity by the system β-carotene/ácido linoleic method and by DPPH radical scavernging assay, the ethanol extract from the laboratory process showed significantly greater activity than the other extracts, being and the first and second methods, respectively, lower and equivalent to the synthetic antioxidant BHT. The handmade ethanol extract has not demonstrated skill in deactivating free radicals, but showed activity in inhibiting lipid peroxidation, although the values were significantly lower than the laboratory sample. We conclude that the dehydration process in the laboratory is the most efficient technique to maintenance of the chemical composition present in the seaweed, providing beneficial properties such as antioxidant capacity. We emphasize that this property can be explored with the objective of adding commercial value to the final product, which will promote the expansion of production of this seaweed in the community of Rio do Fogo

Extração, caracterização e atividades biológicas de proteínas da espécie cnidoscolus urens (L.) Arthur

The extraction, chemical and structural characterization of a wide variety of compounds derived from plants has been a major source of bioactive molecules. Several proteases have been isolated in the plant kingdom, with numerous pharmacological and biotechnological applications. Among the proteases isolated from plants, are the fibrinogenolytic, with relevant application in the treatment of disorders in the coagulation cascade, in addition to potential use as a tool in clinical laboratories. In this study, in addition to evaluating the effects of the protein extract of Cnidoscolus urens (L.) Arthur (Euphorbiaceae) in the coagulation cascade also investigates the presence of antimicrobial activity and characterizes the proteolytic activity detected in this extract, aiming to determine their potential pharmacological and biotechnological application. In this way, crude protein extracts obtained from the leaves of C. urens in Tris-HCl 0.05M, NaCl 0.15M, pH 7.5, were precipitated in different concentrations of acetone, and assessed for the presence of proteolytic activity in azocaseína and fibrinogen. The most active fraction (F1.0) in these tests was chosen for assessment of biological activity and biochemical characterization. The Aα chain and Bβ of fibrinogen were completely cleaved at a concentration of 0.18 μg/μL of protein fraction in 4 minutes. Fibrinogenolytic activity presented total inhibition in the presence of E-64 and partial in the presence of EDTA. The fraction demonstrated coagulant activity in plasm and reduced the APTT, demonstrating acting on the factors coagulation of the intrinsic pathway and common, not exerting effects on the PT. Fibrinolytic activity on plasma clot was detected only in SDS-PAGE in high concentrations of fraction, and there were no defibrinating. Although several proteases isolated from plants and venomous animals are classically toxic, the fraction F1.0 of C. urens not expressed hemorrhagic nor hemolytic activities. Fraction F1.0 also showed no antimicrobial activity. In proteolytic activity on the azocasein, the optimal pH was 5.0 and optimum temperature of 60ºC. The enzyme activity has been shown to be sensitive to the presence of salts tested, with inhibition for all compounds. The surfactant triton did not influence the enzyme activity, but the tween-20 and SDS inhibited the activity. In the presence of reducing agents increase in enzyme activity occurred, a typical feature of enzymes belonging to the class of cysteine proteases. Several bands with proteolytic activity were detected in zymogram, in the region of high-molecular-weight, which were inhibited by E-64. In this study, we found that C. urens presents in its constitution cysteine proteases with fibrinogenolytic and procoagulant activity, which may be isolated, with potential application in treatment of bleeding disorders, thrombolytic and clinical laboratory

Mapeamento de ambientes estruturados com extração de informações geométricas através de dados sensoriais

The objective of this thesis is proposes a method for a mobile robot to build a hybrid map of an indoor, semi-structured environment. The topological part of this map deals with spatial relationships among rooms and corridors. It is a topology-based map, where the edges of the graph are rooms or corridors, and each link between two distinct edges represents a door. The metric part of the map consists in a set of parameters. These parameters describe a geometric figure which adapts to the free space of the local environment. This figure is calculated by a set of points which sample the boundaries of the local free space. These points are obtained with range sensors and with knowledge about the robot s pose. A method based on generalized Hough transform is applied to this set of points in order to obtain the geomtric figure. The building of the hybrid map is an incremental procedure. It is accomplished while the robot explores the environment. Each room is associated with a metric local map and, consequently, with an edge of the topo-logical map. During the mapping procedure, the robot may use recent metric information of the environment to improve its global or relative pose

Técnicas visuais de localização e mapeamento simultâneos sem extração de primitivas geométricas da imagem

In Simultaneous Localization and Mapping (SLAM - Simultaneous Localization and Mapping), a robot placed in an unknown location in any environment must be able to create a perspective of this environment (a map) and is situated in the same simultaneously, using only information captured by the robot s sensors and control signals known. Recently, driven by the advance of computing power, work in this area have proposed to use video camera as a sensor and it came so Visual SLAM. This has several approaches and the vast majority of them work basically extracting features of the environment, calculating the necessary correspondence and through these estimate the required parameters. This work presented a monocular visual SLAM system that uses direct image registration to calculate the image reprojection error and optimization methods that minimize this error and thus obtain the parameters for the robot pose and map of the environment directly from the pixels of the images. Thus the steps of extracting and matching features are not needed, enabling our system works well in environments where traditional approaches have difficulty. Moreover, when addressing the problem of SLAM as proposed in this work we avoid a very common problem in traditional approaches, known as error propagation. Worrying about the high computational cost of this approach have been tested several types of optimization methods in order to find a good balance between good estimates and processing time. The results presented in this work show the success of this system in different environments

Extração e Representação de Conhecimento de Séries Temporais de Demanda de Energia Elétrica Usando TSKR

The opening of the Brazilian market of electricity and competitiveness between companies in the energy sector make the search for useful information and tools that will assist in decision making activities, increase by the concessionaires. An important source of knowledge for these utilities is the time series of energy demand. The identification of behavior patterns and description of events become important for the planning execution, seeking improvements in service quality and financial benefits. This dissertation presents a methodology based on mining and representation tools of time series, in order to extract knowledge that relate series of electricity demand in various substations connected of a electric utility. The method exploits the relationship of duration, coincidence and partial order of events in multi-dimensionals time series. To represent the knowledge is used the language proposed by Mörchen (2005) called Time Series Knowledge Representation (TSKR). We conducted a case study using time series of energy demand of 8 substations interconnected by a ring system, which feeds the metropolitan area of Goiânia-GO, provided by CELG (Companhia Energética de Goiás), responsible for the service of power distribution in the state of Goiás (Brazil). Using the proposed methodology were extracted three levels of knowledge that describe the behavior of the system studied, representing clearly the system dynamics, becoming a tool to assist planning activities

Estudo do potencial de utilização do resíduo da extração de esmeraldas na fabricação de cerâmica de revestimento

Companies involved in emerald mining and treatment represent an important area of industrial development in Brazil, with significative contribution to the worldwide production of such mineral. As a result, large volumes of emerald waste are constantly generated and abandoned in the environment, negatively contributing to its preservation. By the other side the interest of the use of mining waste as additive in ceramic products has been growing from researchers in recent years. The ceramic industry is constantly seeking to the marked amplification for the sector and perfecting the quality of the products and to increase the variety of applications. The technology of obtaining of ceramic tiles that uses mining residues assists market niches little explored. In this scenario, the objective of the present study was to characterize the residue generated from emerald mining as well as to assess its potential use as raw material for the production of ceramic tiles. Ceramic mixtures were prepared from raw materials characterized by X-ray fluorescence, X-ray diffraction, particle size analysis and thermal analysis. Five compositions were prepared using emerald residue contents of 0%, 10%, 20%, 30% and 40%. Samples were uniaxially pressed, fired at 1000, 1100 and 1200ºC and characterized aiming at establishing their mineralogical composition, water absorption, apparent porosity, specific mass, linear retraction and modulus of rupture. The results shows that the emerald residue, basically consisted of 73% of (SiO2 + Al2O3) and 17,77% of (MgO + Na2O+ K2O) (that facilitates sintering), can be added to the ceramic tile materials with no detrimental effect on the properties of the sintered products

Extração do óleo e caracterização dos resíduos da borra de petróleo para fins de reuso

The petroleum industry, in consequence of an intense activity of exploration and production, is responsible by great part of the generation of residues, which are considered toxic and pollutants to the environment. Among these, the oil sludge is found produced during the production, transportation and refine phases. This work had the purpose to develop a process to recovery the oil present in oil sludge, in order to use the recovered oil as fuel or return it to the refining plant. From the preliminary tests, were identified the most important independent variables, like: temperature, contact time, solvents and acid volumes. Initially, a series of parameters to characterize the oil sludge was determined to characterize its. A special extractor was projected to work with oily waste. Two experimental designs were applied: fractional factorial and Doehlert. The tests were carried out in batch process to the conditions of the experimental designs applied. The efficiency obtained in the oil extraction process was 70%, in average. Oil sludge is composed of 36,2% of oil, 16,8% of ash, 40% of water and 7% of volatile constituents. However, the statistical analysis showed that the quadratic model was not well fitted to the process with a relative low determination coefficient (60,6%). This occurred due to the complexity of the oil sludge. To obtain a model able to represent the experiments, the mathematical model was used, the so called artificial neural networks (RNA), which was generated, initially, with 2, 4, 5, 6, 7 and 8 neurons in the hidden layer, 64 experimental results and 10000 presentations (interactions). Lesser dispersions were verified between the experimental and calculated values using 4 neurons, regarding the proportion of experimental points and estimated parameters. The analysis of the average deviations of the test divided by the respective training showed up that 2150 presentations resulted in the best value parameters. For the new model, the determination coefficient was 87,5%, which is quite satisfactory for the studied system