Otimização de forma aplicando B-splines sob critério integral de tensões

This work proposes a computational methodology to solve problems of optimization in structural design. The application develops, implements and integrates methods for structural analysis, geometric modeling, design sensitivity analysis and optimization. So, the optimum design problem is particularized for plane stress case, with the objective to minimize the structural mass subject to a stress criterion. Notice that, these constraints must be evaluated at a series of discrete points, whose distribution should be dense enough in order to minimize the chance of any significant constraint violation between specified points. Therefore, the local stress constraints are transformed into a global stress measure reducing the computational cost in deriving the optimal shape design. The problem is approximated by Finite Element Method using Lagrangian triangular elements with six nodes, and use a automatic mesh generation with a mesh quality criterion of geometric element. The geometric modeling, i.e., the contour is defined by parametric curves of type B-splines, these curves hold suitable characteristics to implement the Shape Optimization Method, that uses the key points like design variables to determine the solution of minimum problem. A reliable tool for design sensitivity analysis is a prerequisite for performing interactive structural design, synthesis and optimization. General expressions for design sensitivity analysis are derived with respect to key points of B-splines. The method of design sensitivity analysis used is the adjoin approach and the analytical method. The formulation of the optimization problem applies the Augmented Lagrangian Method, which convert an optimization problem constrained problem in an unconstrained. The solution of the Augmented Lagrangian function is achieved by determining the analysis of sensitivity. Therefore, the optimization problem reduces to the solution of a sequence of problems with lateral limits constraints, which is solved by the Memoryless Quasi-Newton Method It is demonstrated by several examples that this new approach of analytical design sensitivity analysis of integrated shape design optimization with a global stress criterion purpose is computationally efficient

Extração enzimática de óleo e produção in situ de biodiesel a partir da Moringa oleífera Lam

With the growth and development of modern society, arises the need to search for new raw materials and new technologies which present the "clean" characteristic, and do not harm the environment, but can join the energy needs of industry and transportation. The Moringa oleifera Lam, plant originating from India, and currently present in the Brazilian Northeast, presents itself as a multi-purpose plant, can be used as a coagulant in water treatment, as a natural remedy and as a feedstock for biodiesel production. In this work, Moringa has been used as a raw material for studies on the extraction and subsequently in the synthesis of biodiesel. Studies have been conducted on various techniques of Moringa oil extraction (solvents, mechanical pressing and enzymatic), being specially developed an experimental design for the aqueous extraction with the aid of the enzyme Neutrase© 0.8 L, with the aim of analyzing the influence variable pH (5.5-7.5), temperature (45-55°C), time (16-24 hours) and amount of catalyst (2-5%) on the extraction yield. In relation to study of the synthesis of biodiesel was initially carried out a conventional transesterification (50°C, KOH as a catalyst, methanol and 60 minutes reaction). Next, a study was conducted using the technique of in situ transesterification by using an experimental design variables as temperature (30-60°C), catalyst amount (2-5%), and molar ratio oil / ethanol (1:420-1:600). The extraction technique that achieved the highest extraction yield (35%) was the one that used hexane as a solvent. The extraction using 32% ethanol obtained by mechanical pressing and extraction reached 25% yield. For the enzymatic extraction, the experimental design indicated that the extraction yield was most affected by the effect of the combination of temperature and time. The maximum yield obtained in this extraction was 16%. After the step of obtaining the oil was accomplished the synthesis of biodiesel by the conventional method and the in situ technique. The method of conventional transesterification was obtained a content of 100% and esters by in situ technique was also obtained in 100% in the experimental point 7, with a molar ratio oil / alcohol 1:420, Temperature 60°C in 5% weight KOH with the reaction time of 1.5 h. By the experimental design, it was found that the variable that most influenced the ester content was late the percentage of catalyst. By physico-chemical analysis it was observed that the biodiesel produced by the in situ method fell within the rules of the ANP, therefore this technique feasible, because does not require the preliminary stage of oil extraction and achieves high levels of esters

Integração da simulação termoenergética com o processo de projeto: a análise de 6 casos

This work consists of the integrated design process analyses with thermal energetic simulation during the early design stages, based on six practical cases. It aims to schematize the integration process, identifying the thermal energetic analyses contributions at each design phase and identifying the highest impact parameters on building performance. The simulations were run in the DesignBuilder energy tool, which has the same EnergyPlus engine, validated. This tool was chosen due to the flexible and user friendly graphic interface for modeling and output assessment, including the parametric simulation to compare design alternatives. The six case studies energy tools are three architectural and three retrofit projects, and the author the simulations as a consultant or as a designer. The case studies were selected based on the commitment of the designers in order to achieve performance goals, and their availability to share the process since the early pre-design analyses, allowing schematizing the whole process, and supporting the design decisions with quantifications, including energy targets. The thermoenergetic performance analyses integration is feasible since the early stages, except when only a short time is available to run the simulations. The simulation contributions are more important during the sketch and detail phases. The predesign phase can be assisted by means of reliable bioclimatic guidelines. It was verified that every case study had two dominant design variables on the general performance. These variables differ according the building characteristics and always coincide with the local bioclimatic strategies. The adaptation of alternatives to the design increases as earlier it occurs. The use of simulation is very useful: to prove and convince the architects; to quantify the cost benefits and payback period to the retrofit designer; and to the simulator confirm the desirable result and report the performance to the client

Especificações e concepções de front-end UHF integrado e multipadrão em tecnologia CMOS 130nm

The Brazilian Environmental Data Collecting System (SBCDA) collects and broadcasts meteorological and environmental data, to be handled by dozens of institutions and organizations. The system space segment, composed by the data collecting satellites, plays an important role for the system operation. To ensure the continuity and quality of these services, efforts are being made to the development of new satellite architectures. Aiming a reduction of size and power consumption, the design of an integrated circuit containing a receiver front-end is proposed, to be embedded in the next SBCDA satellite generations. The circuit will also operate under the requirements of the international data collecting standard ARGOS. This work focuses on the design of an UHF low noise amplifier and mixers in a CMOS standard technology. The specifi- cations are firstly described and the circuit topologies presented. Then the circuit conception is discussed and the design variables derived. Finally, the layout is designed and the final results are commented. The chip will be fabricated in a 130 nm technology from ST Microelectronics.

Análise funcional do design das órteses para rizartrose

The purpose of this paper is to identify the utilization of two models of orthotics used in the conservative treatment of rizartrose in patients/consumers that were referred by the medical clinic to the LAI (Laboratory of Integrated Accessibility). It describes this group s perception related to the functional aspects of the two models, evaluates the value of the product attributed by the patient/consumer and describes the importance attributed to each model. The research s objective consists in identifying which model this is preferred from the point of view by the patients that use either the dorsal or ventral models used in the conservative treatment of rizartrose . This work is then based on the exploratory research through the investigation of the bibliography available and in the research field. The research field used the case study methodology to investigate the phenomenon in the real context. The data were collected using a patient questionnaire during two times after the use of the dorsal orthotic and after the use of the ventral orthotic. The questionnaire was used to identify the relationship between the patients/consumers and the two different types of orthotics. A general descriptive analysis was used in order to verify the patient s abilities executing certain activities daily living using the dorsal and ventral orthotics, the product s functional aspects and its value from the patient s/consumer s point of view. The results show that the preference for the dorsal or ventral models is determined by the individual needs of each person. The results also show that other variables, such as the use of the orthotic on the dominant or non-dominant hand, play a role in the preferred model by the patient/consumer and need to be further investigated