Síntese, caracterização e aplicação de MCM-41 funcionalizado com diisopropilamina no processo de adsorção do dióxido de carbono

Emissions of CO2 in the atmosphere have increased successively by various mechanisms caused by human action, especially as fossil fuel combustion and industrial chemical processes. This leads to the increase in average temperature in the atmosphere, which we call global warming. The search for new technologies to minimize environmental impacts arising from this phenomenon has been investigated. The capture of CO2 is one of the alternatives that can help reduce emis ions of greenhouse gases. The CO2 can be captured through the process of selective adsorption using adsorbents for this purpose. Were synthesized by hydrothermal method, materials of the type MCM-41 and Al-MCM-41 in the molar ratio Si / Al equal to 50. The synthesis of gels were prepared from a source of silicon, sodium, water and aluminum in the case of Al-MCM-41. The period of synthesis of the materials was 5 days in autoclave at 100°C. After that time materials were filtered, washed and dried in greenhouse at 100 º C for 4 hours and then calcined at 450 º C. Then the calcined material was functionalized with the Di-isopropylamine (DIPA) by the method of wet impregnation. We used 0.5 g of material mesopores to 3.5 mL of DIPA. The materials were functionalized in a closed container for 24 hours, and after this period were dried at brackground temperature for 2 hours. Were subsequently subjected to heat treatment at 250°C for 1 hour. These materials were used for the adsorption of CO2 and were characterized by XRD, FT-IR, BET / BJH, SEM, EDX and TG / DTG. Tests of adsorption of CO2 was carried out under the following conditions: 100 mg of adsorbent, temperature of 75°C under flow of 100 mL/min of CO2 for 2 hours. The desorption of CO2 was carried out by thermogravimetry from ambient temperature to 900ºC under flow of 25 mL min of He and a ratio of 10ºC/min. The difratogramas X-ray for the synthesized samples showed the characteristic peaks of MCM-41, showing that the structure of it was obtained. For samples functionalized there was a decrease of the intensities of these peaks, with a consequent reduction in the structural ordering of the material. However, the structure was preserved mesopores. The adsorption tests showed that the functionalized MCM-41 is presented as a material promising adsorbent, for CO2 capture, with a loss of mass on the desorption CO2 of 7,52%, while that in Al-MCM- 41 functionalized showed no such loss

Caracterização do processo de gelificação de soluções quitosana utilizando reometria e espalhamento dinâmico da luz

Gels consist of soft materials with vast use in several activities, such as in pharmaceutical industry, food science, and coatings/textile applications. In order to obtain these materials, the process of gelification, that can be physical (based on physical interactions) and/or chemical (based on covalent crosslinking), has to be carried out. In this work we used dynamic light scattering (DLS) and rheometry to monitor the covalent gelification of chitosan solutions by glutaraldehyde. Intensity correlation function (ICF) data was obtained from DLS and the exponential stretched Kohrausch-William-Watts function (KWW) was fitted to them. The parameters of the KWW equation, β, Γ and C were evaluated. These methods were effective in clarifying the process of sol-gel transition, with the emergence of non-ergodicity, and determining the range of gelation observed in about 10-20 minutes. The dependence between apparent viscosity on reaction time was used to support the discussion proposed.

Estudo de materiais mesoporosos funcionalizados com diferentes aminas para captura do dióxido de carbono através do processo de adsorção

Intensive use of machinery and engines burning fuel dumps into the atmosphere huge amounts of carbon dioxide (CO2), causing the intensification of the greenhouse effect. Climate changes that are occurring in the world are directly related to emissions of greenhouse gases, mainly CO2, gases, mainly due to the excessive use of fossil fuels. The search for new technologies to minimize the environmental impacts of this phenomenon has been investigated. Sequestration of CO2 is one of the alternatives that can help minimize greenhouse gas emissions. The CO2 can be captured by the post-combustion technology, by adsorption using adsorbents selective for this purpose. With this objective, were synthesized by hydrothermal method at 100 °C, the type mesoporous materials MCM - 41 and SBA-15. After the synthesis, the materials were submitted to a calcination step and subsequently functionalized with different amines (APTES, MEA, DEA and PEI) through reflux method. The samples functionalized with amines were tested for adsorption of CO2 in order to evaluate their adsorption capacities as well, were subjected to various analyzes of characterization in order to assess the efficiency of the method used for functionalization with amines. The physic-chemical techniques were used: X- ray diffraction (XRD), nitrogen adsorption and desorption (BET/BJH), scanning electron microscopy (SEM), transmission electron microscopy (TEM), CNH Analysis, Thermogravimetry (TG/DTG) and photoelectron spectroscopy X-ray (XPS). The CO2 adsorption experiments were carried out under the following conditions: 100 mg of adsorbent, at 25 °C under a flow of 100 ml/min of CO2, atmospheric pressure and the adsorption variation in time 10-210 min. The X-ray diffraction with the transmission electron micrographs for the samples synthesized and functionalized, MCM-41 and SBA-15 showed characteristic peaks of hexagonal mesoporous structure formation, showing the structure thereof was obtained. The method used was efficient reflux according to XPS and elemental analysis, which showed the presence of amines in the starting materials. The functionalized SBA -15 samples were those that had potential as best adsorbent for CO2 capture when compared with samples of MCM-41, obtaining the maximum adsorption capacity for SBA-15-P sample

Gestão por Competências em Organizações Públicas: O Processo de Transformação Organizacional e seus Impactos Junto aos Servidores na Secretaria Estadual de Administração e Recursos Humanos (SEARH/RN)

The state has changed over time in order to meet a society with increasingly stringent demands. Techniques of private means begin to be employed in an attempt to overcome the dysfunctions entrenched bureaucracy, making the machine faster. By federal law by the People Management Skills was established as a reference for the administration of Human Resources of the public sector in an attempt to develop professionally servers, based mainly on the three pillars of the model: the knowledge, skills and attitudes. This thesis aims at understanding, in the view of employees, the perceived impacts on the organizational changes occurring in the Department of Administration and Human Resources of the State of Rio Grande do Norte in order to implement a People Management Skills-based. It is a simple case study, characterized by the research during a certain period of time, collecting data in a real environment of an organization, in this case SEARH/RN. The procedures used in collecting data were the literature review, documental research and field research. We used a qualitative approach with exploratory and descriptive approach. Every reform was implemented in the institution and reported from there analyzed the impacts observed by the servers. As a result we observed a considerable advance in institutional activities, mainly relating to physical structure / organizational and human resource policies, with minor advances on labor policies, in much the result of the guiding focus of the reform on SEARH/RN. The impacts in total were more positive than negative and direct paths to improvement in public organizations. Making a general analysis of the modernization program implemented in SEARH/RN, we can conclude that there was a distinct change in all dimensions studied, mostly pointing out positive aspects, and contrary to the opinion of some authors, who claim to be very difficult to implement reforms in public organizations, since they are highly institutionalized environments. What was found was a big organization, with gaps and weaknesses, but with a much larger number of hits and recognition from institutional actors

O processo de (re)produção do espaço urbano de Nova Parnamirim

The public and private politics that was implemented in Natal, have always been attracting, great contingent of people in search of employments. However, not always, they can attend the migratory demands. Recently, Nova Parnamirim that is situated in the municipal district of Parnamirim - RN, due to proximity with Natal, it is passing for an intensive and accelerated occupation process impelled by the urban politics that created and they determined new diversities, leaning in the growth of the modern tertiary. In this context, Nova Parnamirim is suffering, along the time, substantial transformations in your espace, so much of nature social as environmental, that are affecting in the quality of your residents' life. This fact is mainly linked in the absence of an appropriate urban planning that have to be considered as an instrument norteador of the development of the city in its constant construction process. The study has as objective to analyze the social-space dynamics of the area and their implications, identifying the principal agents that promote and they benefit of that urbanization process. For the ccomplishment of this research it was executed bibliographical readings that turn of theoretical studies about the urban subjects and enviroments, besides field activities for the rising of the data investigated in the methodological approach

Nostalgia do espaço e do tempo: uma leitura da obra memorialística de Câmara Cascudo

This dissertation addresses the work of the memoirs of the potiguar writer Luís da Câmara Cascudo (1898 - 1986) from an integrated reading of four works that comprise: O Tempo e Eu (1968), Pequeno Manual do Doente Aprendiz (1969), Na Ronda do Tempo (1971) and Ontem (1972). Produced under the contingency of the modern movement and urban reform, memories Cascudo evoke the old landscapes of old, populated by those who belonged to the old romantic and provincial Natal that no longer exists, but which still survives in the idealized memory author and that is (re)constructed by him from a written permeated with touches of imagination and a sense of nostalgia. Seeking to analyze how is the process of building memoirist of Cascudo, as well as reflect on the role that memory plays in the (re)construction of a time and a lost space, we used the studies of Maurice Halbwachs (2006) and Ecléa Bosi (1994). Within this theoretical framework, we seek, above all, to understand not only how the lived experiences of Cascudo will work in this matter of his memory, but also as this will guide a writing that touches on the history and social frameworks of the past

Caracterização da comunidade bentônica do recife raso de Pirangi/RN, Brasil, e avaliação do seu processo de estruturação sob impacto de pisoteio

Despite being areas of socioeconomic and ecological importance, the reef environments in northeastern Brazil have been suffering with cluttered tourism impacts, such as trampling, activity that leads to decrease in abundance of organisms, especially benthic, and loss of biodiversity. The objectives of this study were 1) to characterize the benthic community in the shallow sandstone reef of Pirangi/RN, identifying patterns of zonation, and 2) evaluate its process of structuring under different degrees of impact of trampling, providing information to the proper use of the area. Data on abundance of organisms, the percentage coverage of the substrate and physic-chemical parameters were collected. The formation of two zones on the reef was observed: one that considers submerged areas and ones with shorter time of exposure, lower roughness and higher heterogeneity in the coverage of the substrate, with a predominance of sand, foliose algae, rodolit, being related to organisms such as gastropods, crabs and sea-urchin; the second zone comprises areas with longer time of exposure, greater roughness and predominance of bedrock uncovered, being associated with organisms such as barnacles, gastropods, bivalves and crabs. It is concluded that the studied reef presents its own zonation pattern, influenced by both the time of immersion and the substrate characteristics, such as roughness and type of coverage. To answer the second objective of this study, four experimental blocks were mounted on each of the three areas of different intensities of trampling, containing the following treatments: control (isolated from trampling), shaved isolated, trampling and shaved trampling, with data collection by 11 months. The data in abundance, diversity indices and living coverage of the substrate were compared between areas and treatments. The results showed that at the trampling areas, at the end of the experiment, differences were observed between the intensities of the impact, where higher values of abundance and richness of mobile fauna and richness of live coverage (ANOVA, p <0.05) were found in the area of higher trampling intensity. For fauna withdrawal of trampled scraped treatments, it was observed in the area of greatest impact that the abundance of small benthic invertebrates is more than three times smaller than that at the area of intermediate trampling (ANOVA, p <0.05). Initial isolated areas and final ones differed only as to the percentage of live coverage, with an increase of 35% at the end of this experiment. As for the areas that were completely scraped and isolated at the end of the experiment was observed an increase in the percentage of live coverage of 11.11% compared to the initial amount in the area of intermediate impact and 37.5% in the area with greater impact, indicating recovery of the area. It is suggested that the current use of the reef of Pirangi be reviewed, with a decentralization of trampling, or a decrease in visits, so that it does not occur at high intensities

Processo de cuidar de crianças hospitalizadas com câncer

The objective was to understand the process of care in the perception of hospitalized children with cancer. This is a descriptive study of qualitative approach. Data were collected between the months of October 2013 and January 2014, through photographic records and semi-structured interview consisting of questions relating to the identification of age, sex, diagnosis and length of stay and a script of questions related to the recorded pictures. Eight children were included aged between six and twelve who were admitted to a pediatric oncology sector, located in the city of Natal / RN. The criteria used in the sample were: being hospitalized for cancer treatment; and present favorable physical conditions for carrying out the data collection. For the treatment of collected material was used content analysis, thematic modality. The study followed the ethical and legal principles governing scientific research with human beings and took place with the approval of the project by the Ethics and Research Committee of the Northern League Riograndense against Cancer, with opinion registered under number 329 015 and CAAE 16097613.9.0000.5293. According to the results it was found that, for the child, the care happens through technical activities, such as making procedures and the use of personal protective equipment, as well as through the dialogic relationship, which favors the establishment of confidence in care professional. Caring also means developing activities that promote well-being, the fun and the social and cognitive development, highlighting thus the playful, during hospitalization, as an auxiliary tool in the care process. During hospitalization, the child identifies two individuals responsible for their care, accompanying family and professional, and nursing professionals the most cited in moments of care. , Also of note, the promotion of care, in the perception of the child related to the infrastructure of the institution, environmental cleaning, personal hygiene, the medicalization and the food. It is concluded that care understood by the child, whilst still maintaining relations with the biomedical model, points to a new perspective that should consider the biological, social and psychological of acquiring cancer without unlink them of the development child. 9 Moreover, we see the child as an active social actor in this process, and therefore needs to be heard and answered their needs

Integração da simulação termoenergética com o processo de projeto: a análise de 6 casos

This work consists of the integrated design process analyses with thermal energetic simulation during the early design stages, based on six practical cases. It aims to schematize the integration process, identifying the thermal energetic analyses contributions at each design phase and identifying the highest impact parameters on building performance. The simulations were run in the DesignBuilder energy tool, which has the same EnergyPlus engine, validated. This tool was chosen due to the flexible and user friendly graphic interface for modeling and output assessment, including the parametric simulation to compare design alternatives. The six case studies energy tools are three architectural and three retrofit projects, and the author the simulations as a consultant or as a designer. The case studies were selected based on the commitment of the designers in order to achieve performance goals, and their availability to share the process since the early pre-design analyses, allowing schematizing the whole process, and supporting the design decisions with quantifications, including energy targets. The thermoenergetic performance analyses integration is feasible since the early stages, except when only a short time is available to run the simulations. The simulation contributions are more important during the sketch and detail phases. The predesign phase can be assisted by means of reliable bioclimatic guidelines. It was verified that every case study had two dominant design variables on the general performance. These variables differ according the building characteristics and always coincide with the local bioclimatic strategies. The adaptation of alternatives to the design increases as earlier it occurs. The use of simulation is very useful: to prove and convince the architects; to quantify the cost benefits and payback period to the retrofit designer; and to the simulator confirm the desirable result and report the performance to the client

Avaliação térmica e desempenho do processo de secagem de misturas de graviola e leite em secador de leito de jorro

The soursop (A. muricata) is a fruit rich in minerals especially the potassium content. The commercialization of soursop in natura and processed has increased greatly in recent years. Drying fruit pulp in order to obtain the powdered pulp has been studied, seeking alternatives to ensure the quality of dehydrated products at a low cost of production. The high concentration of sugars reducing present in fruits causes problems of agglomeration and retention during fruit pulp drying in spouted bed dryers. On the other hand in relation to drying of milk and fruit pulp with added milk in spouted bed, promising results are reported in the literature. Based on these results was studied in this work drying of the pulp soursop with added milk in spouted bed with inert particles. The tests were based on a 24 factorial design were evaluated for the effects of milk concentration (30 to 50% m/m), drying air temperature (70 to 90 °C), intermittency time (10 to 14 min), and ratio of air velocity in relation to the minimum spout (1.2 to 1.5) on the rate of production, of powder moisture, yield, rate of drying and thermal efficiency of the process. There were physical and chemical analysis of mixtures, of powders and of mixtures reconstituted by rehydration powders. Were adjusted statistical models of first order to data the rate of production, yield and thermal efficiency, that were statistically significant and predictive. An efficiency greater than 40% under the conditions of 50% milk mixture, at 70 ° C the drying air temperature and 1.5 for the ratio between the air velocity and the minimum spout has been reached. The intermittency time showed no significant effect on the analyzed variables. The final product had moisture in the range of 4.18% to 9.99% and water activity between 0.274 to 0.375. The mixtures reconstituted by rehydration powders maintained the same characteristics of natural blends.

Secagem de resíduo de goiaba em secador convectivo de bandejas: modelagem matemática e análise do processo

Actually, Brazil is one of the larger fruit producer worldwide, with most of its production being consumed in nature way or either as juice or pulp. It is important to highlig ht in the fruit productive chain there are a lot lose due mainly to climate reasons, as well as storage, transportation, season, market, etc. It is known that in the pulp and fruit processing industy a yield of 50% (in mass) is usually obtained, with the other part discarded as waste. However, since most this waste has a high nutrient content it can be used to generate added - value products. In this case, drying plays an important role as an alternative process in order to improve these wastes generated by the fruit industry. However, despite the advantage of using this technique in order to improve such wastes, issues as a higher power demand as well as the thermal efficiency limitation should be addressed. Therefore, the control of the main variables in t his drying process is quite important in order to obtain operational conditions to produce a final product with the target specification as well as with a lower power cost. M athematical models can be applied to this process as a tool in order to optimize t he best conditions. The main aim of this work was to evaluate the drying behaviour of a guava industrial pulp waste using a batch system with a convective - tray dryer both experimentally and using mathematical modeling. In the experimental study , the dryin g carried out using a group of trays as well as the power consume were assayed as response to the effects of operational conditions (temperature, drying air flow rate and solid mass). Obtained results allowed observing the most significant variables in the process. On the other hand, the phenomenological mathematical model was validated and allowed to follow the moisture profile as well as the temperature in the solid and gas phases in every tray. Simulation results showed the most favorable procedure to o btain the minimum processing time as well as the lower power demand.

Construção de bibliotecas de cDNAs subtraídos a partir das sementes de Mamona submetidas à estresse hídrico e análise in silico de transcritos potencialmente expressos sob condições de estresse: Metalotioneina, proteína reprimida por auxina de 12.5 kDa e Glutelina tipo-A3

Estresses ambientais abióticos são fatores que causam respostas ao nível molecular, fisiológico e morfológico em plantas, dependendo também de sua intensidade e duração. É visto que algumas espécies apresentam tolerância a condições estressantes e ao mesmo tempo são fontes naturais de matéria prima para indústria. Nesse contexto encontra-se a mamona (Ricinus comunnis L.), principal fonte de óleo de rícino valorizado por suas aplicações farmacêuticas e principalmente industriais, vem sendo usada como cultura em regiões onde a disponibilidade de água é reduzida, usada como fonte de renda para agricultura da região nordeste brasileira. Visto que pouco se sabe sobre as respostas moleculares que levam essa planta a tolerar regiões secas e como as sementes, principais foco de interesse, respondem a essa escassez, nesse trabalho foram construídas duas bibliotecas de cDNAs, onde a partir de uma abordagem subtrativa, continham RNAs diferencialmente expressos em sementes de plantas mamona submetidas ao estresse hídrico durante 5 dias (biblioteca L7), e a outra RNAs diferencialmente expressos em sementes controle (biblioteca L5). A biblioteca L7 apresentou a maior variedade de transcritos com um total de 182. A maior parte das funções estabelecidas pelo sistema Gene Ontology - GO, foram direcionadas aos “Processos Metabólicos” (526), em segundo “Respostas a estímulos” (57), o terceiro termo mais abundante foram referentes a “Desenvolvimento”(26). Já na biblioteca L5, foram encontrados 91 transcritos, com maior parte de suas funções referentes a “Processos Metabólicos”(413), em segundo “Respostas a estímulos” (8) e em terceiro Regulação (6). Alguns dos transcritos da biblioteca L7 foram escolhidos para análise por repetirem-se mais de 3x e não aparecerem na biblioteca L5, o que indica uma possível regulação positiva sobre estresse. As análises sobre Metalotioneína (4x), mostraram que a sequência de proteica apresentava os domínios conservados que a caracterizava como tipo II, onde são encontrados dois domínios funcionais ricos em cisteína com posições altamente conservadas, desempenhando a função de ligar-se a metais pesados, correlacionadas assim como a atividade de eliminação EROs e defesa contra o estresse oxidativo, além de apresentar homologia com a sequência de Bruguiera gymnorhiza, uma planta de mangue adaptada a ambientes salinos. Analisamos também os transcritos da referente a proteína AUXIN-REPRESSED 12.5 KDA (3x), apontada como sendo reprimida pelo hormônio auxina e associada ao processo de dormência da semente, é descrito em uma família gênica onde vários membros pertencem as vias de resposta ao estresse. Por último, analisamos a proteína GLUTELIN TYPE-A 3 (5x), uma importante proteína de armazenamento com caráter hidrofílico, possivelmente direcionada para o vacúolo. Em nosso trabalho foi possível observar um aumento de transcritos em relação a subtração controle, possivelmente reflexo do aumento do metabolismo da semente, tanto para resposta defensiva ao estresse hídrico quanto para o amadurecimento rápido da semente onde foram observados transcritos referentes a resposta oxidativa, controle hormonal, proteínas de reserva e produção de óleo.

Registro global de nuvens de pontos RGB-D em tempo real usando fluxo óptico e marcadores

Registration of point clouds captured by depth sensors is an important task in 3D reconstruction applications based on computer vision. In many applications with strict performance requirements, the registration should be executed not only with precision, but also in the same frequency as data is acquired by the sensor. This thesis proposes theuse of the pyramidal sparse optical flow algorithm to incrementally register point clouds captured by RGB-D sensors (e.g. Microsoft Kinect) in real time. The accumulated errorinherent to the process is posteriorly minimized by utilizing a marker and pose graph optimization. Experimental results gathered by processing several RGB-D datasets validatethe system proposed by this thesis in visual odometry and simultaneous localization and mapping (SLAM) applications.

Otimização de parâmetros mecânicos e microestruturais dos moldes em areia de sílica ligados quimicamente pelo processo de cura a frio em fundição de aço

Surface defects on steel parts borne costs of smelting industries due to the need of rework. Sand molds are frequently used in foundry industries and largely responsible for providing surface defects. This study aims to optimize the levels of the molding process variables to minimize the occurrence of surface defects in steel castings in silica sand molds chemically linked by cold cure process. The methodology used the experimental design with split plot, being considered in the study the resin percentage factors in the mold formulation, addition of iron oxide, type of paint, the paint application method, amount of ink layers, use of hot air along the lines and waiting time of the mold before casting. They were analyzed as response variables erosion defects, sand inclusion, penetration, porosity and surface finish. Tensile strength tests were performed to evaluate the influence of factors on mechanical parameters and the microstructural parameters were carried out the analysis of X-ray diffraction, scanning electron microscopy (SEM) and thermal analysis (TG / DSC / dilatometry). The results elucidate that for the faulty erosion, the only significant factor with a 95% confidence level was the type of ink and the ink alumina-based superior results obtained. For the sand inclusion of defect, there were three significant factors, with best results obtained with alumina-based paint and spray applied using hot air in the mold before casting the metal. For the defect penetration, there were four significant factors, the best results being achieved with 0.8% of resin and addition of iron oxide in the molding formulation, the paint being applied by brush and standby time of 24 hours before leak. For the defect porosity with a 95% confidence level, no significant factors. For the defect surface finish, the best results were achieved with the 0.8% formulation of the resin in the mold and application of the paint brush. To obtain the levels of the factors that optimize all defects simultaneously, we performed a weighted average of the results of each type of fault, concluding that the best levels of the factors were: 0.8% resin and addition of iron oxide in the formulation of the template, application of two coats of paint applied with a brush or spray, using hot air in the mold before casting and 24 hours of waiting ready the mold before casting. These levels of the optimized factors were used in an experiment to confirm that ratified the results, helping to reduce rework and consequently reducing costs of cast steel parts.

Avaliação do desempenho da paligorsquita modificada e do carvão da pirólise do lodo de esgoto no processo de degradação fotocatalítica do fenol

The uncontrolled disposal of wastewaters containing phenolic compounds by the industry has caused irreversible damage to the environment. Because of this, it is now mandatory to develop new methods to treat these effluents before they are disposed of. One of the most promising and low cost approaches is the degradation of phenolic compounds via photocatalysis. This work, in particular, has as the main goal, the customization of a bench scale photoreactor and the preparation of catalysts via utilization of char originated from the fast pyrolysis of sewage sludge. The experiments were carried out at constant temperature (50°C) under oxygen (410, 515, 650 and 750 ml min-1). The reaction took place in the liquid phase (3.4 liters), where the catalyst concentration was 1g L-1 and the initial concentration of phenol was 500 mg L-1 and the reaction time was set to 3 hours. A 400 W lamp was adapted to the reactor. The flow of oxygen was optimized to 650 ml min-1. The pH of the liquid and the nature of the catalyst (acidified and calcined palygorskite, palygorskite impregnated with 3.8% Fe and the pyrolysis char) were investigated. The catalytic materials were characterized by XRD, XRF, and BET. In the process of photocatalytic degradation of phenol, the results showed that the pH has a significant influence on the phenol conversion, with best results for pH equal to 5.5. The phenol conversion ranged from 51.78% for the char sewage sludge to 58.02% (for palygorskite acidified calcined). Liquid samples analyzed by liquid chromatography and the following compounds were identified: hydroquinone, catechol and maleic acid. A mechanism of the reaction was proposed, whereas the phenol is transformed into the homogeneous phase and the others react on the catalyst surface. For the latter, the Langmuir-Hinshelwood model was applied, whose mass balances led to a system of differential equations and these were solved using numerical methods in order to get estimates for the kinetic and adsorption parameters. The model was adjusted satisfactorily to the experimental results. From the proposed mechanism and the operating conditions used in this study, the most favored step, regardless of the catalyst, was the acid group (originated from quinone compounds), being transformed into CO2 and water, whose rate constant k4 presented value of 0.578 mol L-1 min-1 for acidified calcined palygorskite, 0.472 mol L-1 min-1 for Fe2O3/palygorskite and 1.276 mol L-1 min-1 for the sludge to char, the latter being the best catalyst for mineralization of acid to CO2 and water. The quinones were adsorbed to the acidic sites of the calcined palygorskite and Fe2O3/palygorskite whose adsorption constants were similar (~ 4.45 L mol-1) and higher than that of the sewage sludge char (3.77 L mol-1).