Projeto de um Transformador utilizado em uma Planta de Plasma

This work discusses the design of a transformer used in a plant plasma. This plant, which is being developed in UFRN, will be used in the treatment of waste. It consists basically of a radio frequency power supply and a inductive plasma torch. The transformer operates at the nominal frequency of 400 kHz, with 50 kW, allowing the adaptation of impedance between the power supply and torch. To develop the project, a study was done on the fabrication technologies and physical effects on the frequency of operation. This was followed by the modeling of this transformer. Finally, simulations and tests were conducted to validate the design

Projeto em FPGA de um controlador unificado para correção de fator de potência em retificadores boost bidirecionais monofásicos

The use of Field Programmable Gate Array (FPGA) for development of digital control strategies for power electronics applications has aroused a growing interest of many researchers. This interest is due to the great advantages offered by FPGA, which include: lower design effort, high performance and highly flexible prototyping. This work proposes the development and implementation of an unified one-cycle controller for boost CFP rectifier based on FPGA. This controller can be applied to a total of twelve converters, six inverters and six rectifiers defined by four single phase VSI topologies and three voltage modulation types. The topologies considered in this work are: full-bridge, interleaved full-bridge, half-bridge and interleaved half-bridge. While modulations are classified in bipolar voltage modulation (BVM), unipolar voltage modulation (UVM) and clamped voltage modulation (CVM). The proposed project is developed and prototyped using tools Matlab/Simulink® together with the DSP Builder library provided by Altera®. The proposed controller was validated with simulation and experimental results

Análise e projeto de superfícies seletivas em frequência multibanda e/ou banda larga

Frequency selective surfaces (Frequency Selective Surface - FSS) are often used in various applications in telecommunications. Some of these applications may require that these structures have response with multiple resonance bands. Other applications require that the FSS response have large frequency range, to meet the necessary requirements. FSS to design with these features there are numerous techniques cited in the scientific literature. Thus, the purpose of this paper is to examine some common techniques such as: Overlap of FSS; Elements combined; Elements Elements convolucionados and fractals. And designing multiband FSS and / or broadband selecting simple ways in terms of construction and occupy the smallest possible space, aiming at practical applications. Given these requirements, three projects FSS were performed: a technology applied to IEEE 802.11 a/b/g/n and two projects for application in UWB. In project development, commercial software Ansoft DesignerTM and experimental results were satisfactory was used

Projeto e Implementação em Ambiente Foundation Fieldbus de Filtragem Estocástica Baseada em Análise de Componentes Independentes (M175)

This work considers the development of a filtering system composed of an intelligent algorithm, that separates information and noise coming from sensors interconnected by Foundation Fieldbus (FF) network. The algorithm implementation will be made through FF standard function blocks, with on-line training through OPC (OLE for Process Control), and embedded technology in a DSP (Digital Signal Processor) that interacts with the fieldbus devices. The technique ICA (Independent Component Analysis), that explores the possibility of separating mixed signals based on the fact that they are statistically independent, was chosen to this Blind Source Separation (BSS) process. The algorithm and its implementations will be Presented, as well as the results

Projeto, construção e levantamento de desempenho de um concentrador solar cilíndro parabólico com mecanismo automático de rastreamento solar

An cylinder-parabolic solar concentrator is presented to produce steam for different applications. This prototype was built in glass fiber with dimensions that follow a study of optimization of parameters inherent in the optical reflection of sunlight by the surface of reflection and absorption of the same by tubing that leads the fluid of work. The surface of the concentrator of 2.24 m² has been covered by layers of mirror with 1.0 m of lenght and 2.0 cm wide. The absorb tubing consists of a copper tube diameter equal to 28 mm. The concentrator is moving to follow the apparent motion of the sun. It will be presented the processes of manufacturing and assembly of the concentrator proposed, which has as main characteristics the facilities construction and assembly, in addition to reduced cost. Will be presented data from tests performed to produce steam setting up some parameters that diagnose the efficiency of the concentrator. It will be demonstrated the viabilities thermal, economic and of materials of the proposed system.The maximum temperature achieved in the vacuum tube absorber was 232.1°C and average temperature for 1 hour interval was 171.5°C, obtained in a test with automation. The maximum temperature achieved in the output of water was 197.7°C for a temperature of 200.0°C in the absorber tube. The best average result of the water exit temperature to interval of 1 hour was 170.2°C for a temperature of 171.2°C, in the absorber tube, obtained in test with automation. Water exit mean temperatures were always above of the water steaming temperature. The concentrator present a useful efficiency of 38% and a production cost of approximately R$ 450,00 ( $ 160.34)

Projeto, construção e análise de desempenho de coletores solares alternativos utilizando garrafas pet

A solar alternative system for water heating is presented. It work on a thermosiphon, consisting of one or two alternative collectors and a water storage tank also alternative, whose main purpose is to socialize the use of energy mainly to be used by people of low income. The collectors were built from the use of pets bottles, cans of beer and soft drinks and tubes of PVC, ½ " and the thermal reservoirs from a drum of polyethylene used for storage of water and garbage placed inside cylinder of fiber glass and EPS ground between the two surfaces. Such collectors are formed by three elements: pet bottles, cans and tubes absorbers. The heating units, which form the collector contains inside the cans that can be closed, in original form or in the form of plate. The collectors have an absorber grid formed by eight absorbers PVC tube, connected through connections at T of the same material and diameter. It will be presented data of the thermal parameters which demonstrate the efficiency of the heating system proposed. Relative aspects will be boarded also the susceptibility the thermal degradation and for UV for the PVC tubes. It will be demonstrated that this alternative heating system, which has as its main feature low cost, presents thermal, economic and materials viabilities

Projeto, construção e análise de desempenho de um forno solar alternativo tipo caixa a baixo custo

An alternative box-type solar oven constructed from the scrap iron of a gas conventional cook is presented, which functions principles are the effect greenhouse and the concentration. The oven of the conventional cook is the baking enclosure where the absorber (pot) of the solar oven is located, being re-covered for a glass blade for the generation of the greenhouse effect isolated lateral and having deep its and for a composite the plaster base and EPS. Segments of plain mirrors had been placed in the laterals of the oven for the concentration of the radiation and a reflecting parabola was introduced in the baking enclosure for the exploitation of the incident reflected radiation in the interior of the oven. The oven is mobile to allow one better aiming of exactly in relation to the apparent movement of the sun. The thermal economic and of materials viabilities of the stove in study will be demonstrate The average internal temperature of the absorber was around 150°C and the internal temperature around 120°C. Will demonstrate that its low cost and good thermal performance represents basic characteristics for the viability of large use of such archetype, mainly for cooking the decreases and averages temperatures. One will reveal that the archetype in study is competitive with the box-type solar cooker conceived in the whole world

Projeto, construção e análise de eficiência térmica de um sistema de aquecimento solar de água de baixo custo

We studied the feasibility of using a system of Solar Water Heating (SAS) with low cost, for three configurations. In configurations I and II have the collector grid absorber composed of six PVC tubes placed in parallel on the tile cement. In configuration II, the PVC tubes were transparent cover made of plastic bottles. Configuration III uses a collector composed of 12 black HDPE pipes, supported on four cement tiles 2.44 m x 0.50 m, two by two overlapping and interspersed with a filling of glass wool, comprising an area exposed to the global radiation incident of 2.44 m2, with the top two tiles painted matte black. In this configuration, the HDPE pipes replace conventional PVC pipes painted black. The total cost of SAS for configuration III, the most economical, was around $ 150.00. For the configurations tested the system of operation was thermosyphon collector. The study showed that the proposed systems have good thermal efficiency, are easy to install and handle and have low cost compared to conventional.

Aperfeiçoamento no projeto de um protótipo de misturador-decantador à inversão de fases visando aplicação na indústria do petróleo

In the oil industry the mixture oil/water occurs in the operations of production, transportation and refining, as well as during the use of its derivatives. The amount of water produced associated with the oil varies and can reach values of 90% in volume in the case of mature phase of the production fields. The present work deals with the development of new design of the Mixer Settler based on Phase Inversion (MDIF) in a laboratory scale. We envisage this application in industrial scale so the phases of project, construction and operation are considered. The modifications most significant, in comparison with the original prototype, include the materials of construction and the substitution of the equipment used in the mixing stage of the process. It was tested the viability of substitution of the original system of mechanical mixing by a static mixer. A statistical treatment by means of an experimental design of composed central type was used in order to evaluate the behavior of the main variables of the separation process as function of the efficiency of separation for the new device. This procedure is useful to delimit an optimal region of operation with the equipment. The variables of process considered on the experimental design were: oil concentration in the feeding water (mg/L); Total volumetric flow rate (L/h); Ratio organic/water on volumetric basis (O/A). The separation efficiency is calculated by comparison of the content of oil and greases in the inlet and outlet of the equipment. For determination of TOG (Total Oil and Grease), the method used was based in the absorption of radiation in the infra-red region. The equipment used for these determinations was InfraCal® TOG/TPH Model HATR-T2 of the Wilks Enterprise, Incorporation. It´s important to stand out that this method of measure has being used by PETROBRAS S.A. Results of global efficiency of separation oil/water varied from 75.3 to 97.7% for contaminated waters containing up to 1664,1 mg/L of oil. By means of tests carried out with a real sample of contaminated water supplied by PETROBRAS we have got an effluent specified in terms of the legal standards required for discharging. Thus, the new design of equipment constitutes a real alternative for the conventional systems of treatment of produced water in the oil industry

Projeto e Operação em Escala Semi-Industrial de um Equipamento para Tratamento de Águas Produzidas na Indústria do Petróleo Utilizando Nova Tecnologia: misturador-decantador à inversão de fases - MDIF

The aim of this work is to use a new technology in the treatment of produced wastewaters from oil industry. An unit for treat produced waters called UTMDIF, was designed, installed and operated in an industrial plant for treatment of effluents from oil industry. This unit operates by means of the method of separation of phase inversion and can become a promising alternative to solve the problem of oil/water separation. This method constitutes the basis of the working of a new design of mixersettler of vertical configuration which occupies small surface area. The last characteristic becomes specially important when there is limitation on the lay-out of the plant, for example, over maritime platforms to explore oil. This equipment in a semi-industrial scale treats produced wastewaters contaminated with oil at low concentrations (ranging from 30 to 150 mg/L) and throughputs of 320 m3/d (47,4 m3 m-2 h-1). Good results were obtained in oil/water separation which leads to the necessary specification to discharge those wastewaters. Besides, the non dependence of the efficiency of separation in spite of the salinity of the medium becomes the equipment an attractive new technology to treat wastewaters containing oil at low concentrations

Controle sanitário e ambiental de um projeto de reúso em um complexo de prédios corporativos

The study that resulted in this dissertation was developed at OU RNCE PETROBRAS, in Natal, which implemented a project of rational use and reuse of water, including use of wastewater from a Sewage Treatment Plant (STP) already in place, diluted with water from own wells for irrigation of green area of the building complex corporate enterprise. Establish a methodology that can serve as guidelines for future projects controlled reuse of water like this was the objective of this research. Been proposed, implemented and evaluated three instruments of sanitary and environmental control: 1) adaptation of sewage treatment plant and quality control of the treated effluent 2) analysis of soil-nutrient interaction in the irrigated area, 3) knowledge of the local hydrogeology, especially with regard to the direction of flow of the aquifer and location of collection wells of Companhia de Águas e Esgotos do Rio Grande do Norte (CAERN) situated in the surroundings. These instruments have proven sufficient and appropriate to ensure the levels of sanitary and environmental control proposed and studied, which were: a) control of water quality off the STP and the output of the irrigation reservoir, b) control of water quality sub surface soil and assessment of progress on soil composition, c) assessment of water quality in the aquifer. For this, we must: 1) establishing the monitoring plan of the STP and its effluent quality sampling points and defining the parameters of analysis, improve the functioning of that identifying the adequacy of flow and screening as the main factors of operational control, and increase the efficiency of the station to a relatively low cost, using additional filters, 2) propose, implement and adapt simple collectors to assess the quality of water percolating into the soil of the irrigated area, 3) determine the direction of groundwater flow in the area study and select the wells for monitoring of the aquifer.

Diagnóstico do usuário no aprimoramento dos serviços de tecnologia da informação: um projeto de intervenção para o Ministério Público do Estado do Rio Grande do Norte

The information tecnology (IT) has, over the years, gaining prominence as a strategic element and competitive edge in organizations, public or private. In the judiciary, with the implementation of actions related to Judiciário Eletrônico, information technology (IT), definitely earns its status as a strategic element and significantly raises the level of dependence of the organs of their services and products. Increasingly, the quality of services provided by IT has direct impact on the quality of services provided by the agency as a whole. The Ministério Público do Estado do Rio Grande do Norte (MPRN) deployments shares of Electronic Government, along with an administrative reform, beyond these issues raised, caused a large increase in institutional demand for products and services provided by the Diretoria de Tecnologia da Informação (DTI), a sector responsible for the provision of IT services. Taking as starting point strategic goal set by MPRN to reach a 85% level of user satisfaction in four years, we seek to propose a method that assists in meeting the goal, respecting the capacity constraints of the IT sector. To achieve the proposed objective, we conducted a work in two distinct and complementary stages. In the first step we conducted a case study in MPRN, in which, through an internal and external diagnosis of DTI, accomplished by an action of internal consulting and one research of the user satisfaction, we seek to identify opportunities of change seeking to raise the quality perceived of the services provided by the DTI , from the viewpoint of their customers. The situational report, drawn from the data collected, fostered changes in DTI, which were then evaluated with the managers. In the second stage, with the results obtained in the initial process, empirical observation, evaluation of side projects of quality improvement in the sector, and validation with the managers, of the initial model, we developed an improved process, gazing beyond the identification of gaps in service a strategy for the selection of best management practices and deployment of these, in a incremental and adaptive way, allowing the application of the process in organs with little staff allocated to the provision of information technology services

Caracterização e modelagem dos sistemas de produção de caprinos leiteiros

The objectives of this research were characterizing the dairy goat production systems and model it using linear program. On the first step of this research, the model was developed using data from farms that was affiliated in the ACCOMIG/Caprileite, used a similar dairy goat production systems and have a partnership program with Universidade Federal de Minas Gerais . The data of research were from a structured questionnaire applied with farmers and monitoring of production systems during a guided visit on their farms. The results permitted identify that all farms were classified as a small and have a intensive production system. The average herd size had 63.75 dairy goats on lactation; it permits a production of 153, 38 kg of goat milk per day. It was observed that existing more than one channel of commercialization for the goat milk and their derivative products. The data obtained, on the first step of this research, was used to develop a linear program model. It was evaluated in two goat production systems, called P1 and P2. The results showed that the P1 system, with an annual birth and lactation during approximately 300 days was the best alternative for business. These results were compared with a mixed (beef and dairy) goat system in the semiarid region, which indicated merged with both systems. Therefore, to achieve profits and sustainability of the system, in all simulations it was necessary a minimum limit of funding of U.S. $ 10,000.00; this value permit earning of U.S. $ 792.00 per month and pay the investment within 5 years

Prospecção e formação no domínio das competências e habilidades em tecnologia da informação: o caso do projeto metrópole digital em Natal/RN

This study deals with cognitive competences and abilities that are relevant to selection and education regarding Information Technology (IT). These competences relate to problem solving, decision making, and practical intelligence that regard scholar and extracurricular knowledge mobilization. The research aimed to contribute for the improvement of a selection instrument, consisting of five arrays of skills (dealing with objectives and prospection), as well as the development and comprehension of those skills that are involved in IT education. This is done by means of an analysis on the selection instrument used in the first selective process that occurred at Metropole Digital an Institute at the Federal University of Rio Grande do Norte in Brazil. This was evaluated aiming to acknowledge IT education (with basic training and emphasis on Web programming and electronics). The methodology used was of quantitative method involving performance scores relating education delivery. An Anova analysis of variance was done along with descriptive analysis involving socioeconomic data that was not observed in the meaningful relations between parental instruction and student performance in the graduate course. These analyses were able to point out the importance and need of the policies for vacancy reservation on behalf of public school students. A Spearman correlation analysis was done considering the instrument selection performance in the training course. The instrument is presented as a predictor that is significantly moderate and presents a good performance in the course as a whole. A Cluster and Regression analysis was also realized in the process. The first analysis allowed finding performance groups (Clusters) that ranged from medium and inferior. The regression analysis was able to point out association amongst criterion variables and the (average performance in basic and advanced modules) and explanatory (five matrixes). Regression analysis indicated that matrix 1 and matrix 3 were pointed out as being the strongest ones. In all the above analysis, the correlation between the instrument and the course was considered moderate. Thus this can be related in some of the aspects present in the course such as emphasis on evaluation itself as well as in technical contents and practical skills (educational ones) and competences and selection skills. It is known that the mediation of technological artifact in cultural context can foster the development of skills and abilities relevant to IT training. This study provides subsidies to reflect on the adoption of selection instrument and IT training in the Institute. Thus the research offers means to achieve a interdisciplinary discussion and enriching of areas such as Psychology and Information Technology; all of which regarding competencies and skills relevant in IT training

Projeto pedagógico: abordagens e implicações no âmbito da formação em odontologia

Proposals that aim a redirection of current health attention models in Brazil are indispensible due to the need of health issues and its challenges imposed by society. These issues come forth in Higher Education Institutions in an attempt to devise ways to face these demands. The research aims to analyze the Pedagogical Project (PP) present in the Dentistry Graduation Course in the Federal University of Rio Grande do Norte in Brazil-(UFRN). This is done in coherence the Brazilian National Curricular Guidelines considering main competences established in the PP. This research was approved by the Ethics Committee at UFRN under document number 285/201. The work is of descriptive nature and was realized with 30 students in the Dentistry Graduation Course. Interviews were realized with the use of problem situation approach. The research was also supported by documental studies that dealt with syllabus present in the disciplines taught at UFRN. Data were processed with the use of the ALCESTE 4.9 software. It is possible to acknowledge that some conservative conceptions arise, even though there is use of active methodologies and innovation that aim to promote reflection and articulation for general competence development such as proposed in the Pedagogical Project in Dentistry Graduation Course at UFRN. These conceptions are mainly present in the teaching-learning process where students do not have full participation. Thus it is possible to conclude that even though there are advances and breakthroughs. This is seen with that fact that there was inclusion of multidisciplinary clinical work as well optional courses in the curriculum. It was also seen that there was occasional use of active teaching methodologies in Dentistry at UFRN. But there is still a need for a didactical and methodological resizing. These actions require the need for progressive development of competences and abilities during the formative process according to what was established in the Brazilian National Curricular Guidelines