Desgaste corrosivo-cavitativo-erosivo de um aço-carbono em meio aquoso com frações de sal (NaCl), CO2 e particulados sólidos (SiO2)

A batch of eighty-four coupons of low carbon steel were investigated at laboratory conditions under a corrosive, cavitative-corrosive (CO2) and corrosive-erosive (SiO2 + CO2) in an aqueous salt solution and two levels of temperature. The following measurements were made on Vickers (HV0,05, HV0,10, HV0,20) Microhardness tests at three levels of subsurface layer. A turbulent flow collided on the cylindrical sample, with and without mechanical stirring and gas bubbling, with and without fluid contamination by solid particles of SiO2, at two temperatures. Surface Roughness and Waviness, under two conditions "as received, after machining" and "after worn out", as well as gravimetric and electrochemical parameter were measured on the two opposite generatrices of each cylindrical sample, on the flow upstream (0°) and downstream (180°) by Profilometry, Mass Variation and Linear Polarization Resistance (LPR). The results of the Microhardness and Surface Texture of all coupons were subjected to statistical comparison, using the software Statgraphics® Centurion XVI, 95% statistical certainty, and significant differences were observed in some arrays of measurements. The corrosive wear rate measured by LPR and mass variation shown to be sensitive to the presence of bubbles and hydrodynamic fluctuations inside the cell, considering the temperature and contamination of corrosive fluid by solid particles. The main results of visual inspection relative to some topologies of the surface damages involving different mechanisms that were seen to give explanation for some fluctuations in wear rates of the steel experimentally investigated

Análise topológica experimental por perfilometria cíclica indutiva de superficies de paredes estruturais

To enhance the maintenance practices, Oil and Gas Pipelines are inspected from the inside by automated systems called PIG (Pipeline Inspection Gauge). The inspection and mapping of defects, as dents and holes, in the internal wall of these pipelines are increasingly put into service toward an overall Structural Integrity Policy. The residual life of these structures must be determined such that minimize its probability of failure. For this reason, the investigation on the detection limits of some basic topological features constituted by peaks or valleys disposed along a smooth surface is of great value for determining the sensitivity of the measurements of defects from some combinations of circumferential, axial and radial extent. In this investigation, it was analyzed an inductive profilometric sensor to scan three races, radius r1, r2, r3, in a circular surface of low carbon steel, equipped with eight consecutive defects simulated by bulges and holes by orbit, equally spaced at p/4 rad. A test rig and a methodology for testing in laboratory were developed to evaluate the sensor response and identify their dead zones and jumps due to fluctuations as a function of topological features and scanning velocity, four speeds different. The results are presented, analyzed and suggestions are made toward a new conception of sensor topologies, more sensible to detect these type of damage morphologies

Síntese e caracterização do carbeto de molibdênio nanoestruturado para fins catalíticos na reação de oxidação parcial do metano

The nanostructures materials are characterized to have particle size smaller than 100 nm and could reach 1 nm. Due to the extremely reduced dimensions of the grains, the properties of these materials are significantly modified relatively when compared with the conventional materials. In the present work was accomplished a study and characterization of the molybdenum carbide, seeking obtain it with particles size in the nanometers order and evaluate its potential as catalyst in the reaction of partial methane oxidation. The method used for obtaining the molybdenum carbide was starting from the precursor ammonium heptamolybdate of that was developed in split into two oven, in reactor of fixed bed, with at a heating rate of 5ºC/min, in a flow of methane and hydrogen whose flow was of 15L/h with 5% of methane for all of the samples. The studied temperatures were 350, 500, 600, 650, 660, 675 and 700ºC and were conducted for 0, 60, 120 and 180 minutes, and the percent amount and the crystallite size of the intermediate phases were determined by the Rietveld refinement method. The carbide obtained at 660ºC for 3 hours of reaction showed the best results, 24 nm. Certain the best synthesis condition, a passivating study was accomplished, in these conditions, to verify the stability of the carbide when exposed to the air. The molybdenum carbide was characterized by SEM, TEM, elemental analysis, ICP-AES, TG in atmosphere of hydrogen and TPR. Through the elemental analysis and ICP-AES the presence carbon load was verified. TG in atmosphere of hydrogen proved that is necessary the passivating of the molybdenum carbide, because occur oxidation in room temperature. The catalytic test was accomplished in the plant of Fischer-Tropsch of CTGAS, that is composed of a reactor of fixed bed. Already the catalytic test showed that the carbide presents activity for partial oxidation, but the operational conditions should be adjusted to improve the conversion

Evolução da biodegradabilidade da matéria orgânica em um sistema de lagoas de estabilização

Waste stabilization ponds (WSP) have been widely used for sewage treatment in hot climate regions because they are economic and environmentally sustainable. In the present study a WSP complex comprising a primary facultative pond (PFP) followed by two maturation ponds (MP-1 and MP-2) was studied, in the city of Natal-RN. The main objective was to study the bio-degradability of organic matter through the determination of the kinetic constant k throughout the system. The work was carried out in two phases. In the first, the variability in BOD, COD and TOC concentrations and an analysis of the relations between these parameters, in the influent raw sewage, pond effluents and in specific areas inside the ponds was studied. In the second stage, the decay rate for organic matter (k) was determined throughout the system based on BOD tests on the influent sewage, pond effluents and water column samples taken from fixed locations within the ponds, using the mathematical methods of Least Squares and the Thomas equation. Subsequently k was estimated as a function of a hydrodynamic model determined from the dispersion number (d), using empirical methods and a Partial Hydrodynamic Evaluation (PHE), obtained from tracer studies in a section of the primary facultative pond corresponding to 10% of its total length. The concentrations of biodegradable organic matter, measured as BOD and COD, gradually reduced through the series of ponds, giving overall removal efficiencies of 71.95% for BOD and of 52.45% for COD. Determining the values for k, in the influent and effluent samples of the ponds using the mathematical method of Least Squares, gave the following values respectively: primary facultative pond (0,23 day-1 and 0,09 day-1), maturation 1 (0,04 day-1 and 0,03 day-1) and maturation 2 (0,03 day-1 and 0,08 day-1). When using the Thomas method, the values of k in the influents and effluents of the ponds were: primary facultative pond (0,17 day-1 and 0,07 day-1), maturation 1 (0,02 day-1 and 0,01 day-1) and maturation 2 (0,01 day-1 and 0,02 day-1). From the Partial Hydrodynamic Evaluation, in the first section of the facultative pond corresponding to 10% of its total length, it can be concluded from the dispersion number obtained of d = 0.04, that the hydraulic regime is one of dispersed flow with a kinetic constant value of 0.20 day-1

Efeitos de acoplamentos biquadráticos e campos aleatórios em vidros de spins

In this work we have studied the effects of random biquadratic and random fields in spin-glass models using the replica method. The effect of a random biquadratic coupling was studied in two spin-1 spin-glass models: in one case the interactions occur between pairs of spins, whereas in the second one the interactions occur between p spins and the limit p > oo is considered. Both couplings (spin glass and biquadratic) have zero-mean Gaussian probability distributions. In the first model, the replica-symmetric assumption reveals that the system presents two pha¬ses, namely, paramagnetic and spin-glass, separated by a continuous transition line. The stability analysis of the replica-symmetric solution yields, besides the usual instability associated with the spin-glass ordering, a new phase due to the random biquadratic cou¬plings between the spins. For the case p oo, the replica-symmetric assumption yields again only two phases, namely, paramagnetic and quadrupolar. In both these phases the spin-glass parameter is zero. Besides, it is shown that they are stable under the Almeida-Thouless stability analysis. One of them presents negative entropy at low temperatures. We developed one step of replica simmetry breaking and noticed that a new phase, the biquadratic glass phase, emerge. In this way we have obtained the correct phase diagram, with.three first-order transition lines. These lines merges in a common triple point. The effects of random fields were studied in the Sherrington-Kirkpatrick model consi¬dered in the presence of an external random magnetic field following a trimodal distribu¬tion {P{hi) = p+S(hi - h0) +Po${hi) +pS(hi + h0))- It is shown that the border of the ferromagnetic phase may present, for conveniently chosen values of p0 and hQ, first-order phase transitions, as well as tricritical points at finite temperatures. It is verified that the first-order phase transitions are directly related to the dilution in the fields: the extensions of these transitions are reduced for increasing values of po- In fact, the threshold value pg, above which all phase transitions are continuous, is calculated analytically. The stability analysis of the replica-symmetric solution is performed and the regions of validity of such a solution are identified

Propriedades magnéticas quase-estáticas de filmes ferromagnéticos amorfos de FeCuNbSiB

Today, one of the topics that attracts interest of the scientific community is the understanding of magnetic properties of magnetic systems with reduced dimensions, in particular, ferromagnetic thin films. In this case, the comprehension and control of these properties, as well as the development of routes to obtain them, are crucial issues in many aspects of current and future technologies for storage and transmission of information in the electro-electronic industry. There are several materials that exhibit soft magnetic properties, and we highlight the amorphous alloys and that ones obtained by partial crystallization, so-called nanocrystalline materials. The production of these alloys as magnetic ribbons is very common in scientific and technological area, but there are just a few works related to the production of these alloys as thin films. In this work, we studied the quasi-static magnetic properties of ferromagnetic thin films based on FeCuNbSiB in a wide range of thicknesses, from 20 to 500 nm, produced by sputtering. In particular, after the structural characterization performed via X-ray diffraction, the magnetic properties of the sets of samples were investigated using experimental magnetization curve, obtained using a vibrating sample magnetometer, as well as through theoretical curves obtained by theoretical modeling and numerical computation. The modeling process is based on the Stoner Wohlfarth model applied to three dimensions, and adds some energy terms, using as reference experimental results of magnetization. In this case, from the comparison between theoretical and experimental results and the analysis of the constant anisotropy behavior as a function of film thickness, we aim to obtain further information on the magnetization process of the samples, to identify routes for the production of thin films and develop a theoretical to films to use it, in the future, in the obtainment of the theoretical curves of some magnetic measurements, such as magnetoimpedance and magnetoresistance

Qualidade fisiológica de sementes de genótipos de algodoeiro sob estresse salino

The germination of cotton seeds and the seedlings emergency are generally delayed and reduced by the salinity. Although the cotton is considered a tolerant culture, it can suffer substantial reductions in regarding its growth and production when exposed to salinity condition. The aims of this study went evaluate the effect of the saline stress in the germination phase to four cotton genotypes (BRS Rubi, BRS Safira, BRS 201 and CNPA 187 8H), using different osmotic potentials generated with increment of sodium chloride (NaCl). The saline stress was simulated using NaCl aqueous solutions in the potentials: 0.0 (Control); -0.2; -0.4; -0.6; -0.8 and -1.0 MPa. The treatments were monitored by means of tests for analysis of seeds, germination, first counting, speed germination index, length of shoot, radicle length, dry weigth of embrionic axis and shoot/radicle ratio. The tests for germination, first counting and index of germination speed were accomplished using 50 seeds for repetition and for the study of length of shoot, radicle length, dry weigth of embrionic axis and shoot/radicle ratio were used 20 seeds by repetition. For both tests four repetitions were accomplished by genotype for each one of the potentials. The seeds of each repetition were involved in papers Germitest humidified with NaCl solution corresponding to the potential. The repetitions of both tests were maintained in a germinator with saturated humidity. The analysis were initiate four days after the induction of the saline stress. The evaluations of the first three variables analyzed were accomplished daily; the seeds were remove and counted when its germinated. For the length tests just the repetitions corresponding to the potential of NaCl 0,0 MPa were analysis 4 days after the beginning of the induction of the saline stress. The analysis of the repetitions of the potentials -0,2 and -0,4 and of the potentials -0,6, -0,8 and -1,0 MPa they were accomplished with 12 and 20 days, respectively. For accomplishment of the analisis of this test the shoot of the 20 plantules of each repetition was separate from the radicle and both parts were measured. The statistical analyses were performed using the GENMOD and GLM procedures of the SAS. For the variable germination, the cultivates CNPA 187 8H and BRS Safira stood out for the potential -0.8 MPa, with averages of 89% and 81%, respectively. The test of speed germination index to cultivate BRS Safira presented the largest averages for the two higher saline potentials. It was observed that the increase of the saline potential reduces the germination percentage and speed germination index. For each day of evaluation it was verified that the increase of the saline potential causes a reduction of the length both of the shoot and of the radicle. The radicle tends to grow more than the shoot until the potential -0,4 MPa

Investigação do funcionamento cognitivo de pacientes pediátricos diagnosticados com leucemia linfóide aguda - LLA

The present work investigated the cognitive operation of children diagnosed with acute lymphoblastic leukaemia (ALL), accompanied at pediatric oncologic institutions at the city of Natal/RN. Had participated in this study twenty children, of both sexes, between six and twelve years old, with the ALL diagnostic, who were in treatment (n=10) and out of treatment for at least one year (n=10) and were submitted exclusively to chemotherapy as CNS prophylaxis. The utilized protocol of neuropsychological evaluation covered the following cognitive abilities: intellective capability, attentional and memory systems, and executive functions. Data was analyzed through descriptive and inferential measures, with the support of the Mann-Whitney U Test and T-test, considering the influence of the variables sex, age at diagnostic and the past time since the beginning of the treatment over children s performance. The intellective capability evaluation showed low score to the out-of-treatment groups, female and children under five years old to the diagnostic. In concern of attentional systems, groups showed the expected performance. In a relevant way, in the evaluation of executive functions, were found reduced scores within all groups, especially inside the in-treatment group. Memory evaluation pointed to reduced performance in items concerning to learning evolution and spontaneous evocation after interference to the several groups. It can be concluded, reffer to the occurrence of transitory and permanent impact associated to the intrusion of chemotherapic components during the maturational course of the CNS. It s expected that the present investigation and the development of similar studies enable major comprehension about the mode, extension and repercussion of these damages subsidizing the development of strategies which may minimize them and provide better xxiii life quality to this clinical subgroup

Estudo das propriedades psicométricas da escala WHOQOLold em idosos da região Nordeste

The population aging process increases the number of elderly people worldwide. In Brazil, a country of continental size, this process began in the 40s and happens with specific features in each of the different region s realities. This way, this thesis aimed to evaluate the psychometric properties of a elderly s quality of life (QOL) scale, the WHOQOL-old, in a population of the Northeast of Brazil. We sought to investigate the congruence between the content covered by the scale and the ones deemed as relevant by the participants. It aimed also study the validity evidences of the instrument s internal structure. To achieve the research objectives we adopted the design of multiple methods. The research was organized in two studies. For data collection, both studies used a sociodemographic questionnaire to obtain a profile of the participants and the Mini Mental State Exam (MMSE), used as exclusion criterion. A number of 18 elderly residents of the cities of Natal-RN and Campina Grande-PB, mean age of 73.3 years (SD = 5.9) took part od the study, They were organized into three focal groups (FG) in witch they discussed about the concept of QOL, what enhance and what hinders QOL. For Study II, a quantitative approach, 335 elderly from Campina Grande responded scale WHOQOL-old. They are between 65 and 99 years (M = 74.17, SD = 6.5). The FG data were analyzed by categorical thematic content. For the data analysis of the WHOQOL-old scale were used exploratory factor analysis and calculation of the Akaike and Bayesian information criteria. The results of both studies were triangulated. According to the discussions in the FG, health and social participation have central roles in quality of life. Social participation is related to all the other QOL s influences raised. The participants indicated the relevance of religiosity and were divided about the importance of sexual activity. Exploratory factor analysis (EFA) extracted a model of six factors. Two items (OLD_3 and OLD_9), not loaded on any factor and were excluded. The other items had factor loadings > 0.3. The response categories were reduced from five to three. After the scale changes, the empirical model showed better fit (-2loglikelihood = 8993.90, BIC and AIC = 9183.90 = 9546.24) than the theoretical model (-2loglikelihood = 18390.88, AIC = 18678.88 and BIC = 19228.11). Despite the best information criterion values, the RMESA remained above the ideal (0.06). We conclude that the WHOQOL-old presents psychometric parameters below the ideal when used with the Northeast population, but the improvements made the scale s use acceptable. The WHOQOL-old uses observable variables that matches with the participants' perceptions on quality of life. However, new strategies must be tested for a better sacale refinement

Saúde mental em operadores de petróleo do Rio Grande do Norte

The importance of identifying the consequence of the hours worked on people in society has been well recognized within Organizational and Work Psychology. From this point of view, the present research had the objective of analysing the effects of work regimes on the mental health of petroleum operators of Petrobrás. The sample totaled 144 subjects, corresponding to 27% of the work population. The mental health of the participants was evaluated using the following instruments of measurement: QSG-12, Scale of self-esteem, Scale of Positive and Negative Affections and the Scale of Valuable Attributes of IMST, each representing an empirical factor used to indicate and measure the five dimensions of mental health. The subjects perceptions of their work regime and the rest of their conditions of work were evaluated using scales of descriptive attributes of IMST, by applying a semi-structured questionnaire and by use of interviews. A socio-demographic file was used to collect information related to the biographical and socio-occupational profile of the worker sample. The answers to the questionnaire were inserted into the data bank of SPSS (Statistical Package for Social Science), for statistical analysis, and the interviews were analised based on the technique of Contents Analysis recommended by Bardin (1995). The main results revealed that one third of the worker sample were tense; however, the mental health of the majority was preserved. Cluster Analysis applied to the group of seven factors which measured the five dimensions of mental health identified four profiles of psychological well-being shared between members of the sample. It was observed that the people working in the system of Continuous Shift Alternation (TIR) and in the system of Pre-advising tended to present balanced and satisfactory profiles, while the ones which worked in the Administrative Field tended to present anxious and oscillating profiles, and thus were more affected psychologically. These were also the ones that also perceived the more negative aspects of their laborious conditions (reduced chances of self-improvement, physically stressful and financial resources below expectations with which to supply family and personal necessities. In agreement with the ecological model formulated by Warr (1987), the present study concluded that the positive and negative effects on the psychological well-being tended to occur as a consequence of the perceptions the petrol operators developed to face their work conditions

Obtenção de biodiesel através da transesterificação do óleo de farelo de arroz utilizando KI/Al2O3

This study proposes to find a biodiesel through transesterification of rice bran oil with KI/Al2O3 checking the influence of two types of alumina (Amorphous and Crystalline) for conversion into methyl esters. The catalyst was synthesized by the wet impregnation method. Adding 30 mL of 35% KI(aq.) in 10 g of alumina, under stirring at 80 °C for 3 hours. The reaction conditions used in this study were optimized, with a molar ratio methanol:oil of 15:1, 8 h of reaction time and reflux temperature. The catalyst amount was varied in the range of 1 to 5 % wt. The solid catalysts materials were analyzed by: x-ray diffraction (XRD), thermogravimetry (TG), N2 adsorption/desorption, scanning electron microscopy (SEM) and basicity, for the identification of its structure and composition, verifying the presence of basic sites. The results showed that Al2O3(A) presents an amorphous structure, high surface area and a better catalytic activity, in relation to the catalyst synthesized with Al2O3(C) support that proved to have a more crystalline structure, having as well, a lesser surface area, enabling difficulties for the incorporation of active sites. The obtained biodiesel with 5% wt. KI/Al2O3(A) presented physicochemical properties within the standards specified by the Resolution No 7/2008 ANP and obtained the best reaction yield with 95.2%, according to quantitative measurement from the TG, which showed 96.2% conversion into methyl esters. It was furthermore found that with the increasing amount of the quantity of the catalyst in the reaction, there was also an increase in the ester content obtained. The specific mass and the kinematic viscosity were reduced with the increase of the amount of quantity of the catalyst, indicating an increase in the conversion of triglycerides

Estudo da eficácia do tensoativo sorbitano tween 80 veiculado em nanoemulsão contendo óleo de soja, como inibidor de corrosão

Nowadays, the use of chemicals that satisfactorily meet the needs of different sectors of the chemical industry is linked to the consumption of biodegradable materials. In this context, this work contemplated biotechnological aspects with the objective of developing a more environmentally-friendly corrosion inhibitor. In order to achieve this goal, nanoemulsion-type systems (NE) were obtained by varying the amount of Tween 80 (9 to 85 ppm) a sortitan surfactant named polyoxyethylene (20) monooleate. This NE-system was analyzed using phase diagrams in which the percentage of the oil phase (commercial soybean oil, codenamed as OS) was kept constant. By changing the amount of Tween 80, several polar NE-OS derived systems (O/W-type nanoemulsion) were obtained and characterized through light scattering, conductivity and pH, and further subjected to electrochemical studies. The interfacial behavior of these NE-OS derived systems (codenamed NE-OS1, S2, S3, S4 and S5) as corrosion inhibitors on carbon steel AISI 1020 in saline media (NaCl 3.5%) were evaluated by measurement of Open Circuit Potential (OCP), Polarization Curves (Tafel extrapolation method) and Electrochemical Impedance Spectroscopy (EIS). The analyzed NE-OS1 and NE-OS2 systems were found to be mixed inhibitors with quantitative efficacy (98.6% - 99.7%) for concentrations of Tween 80 ranging between 9 and 85 ppm. According to the EIS technique, maximum corrosion efficiency was observed for some tested NE-OS samples. Additionaly to the electrochemical studies, Analysis of Variance (ANOVA) and Principal Component Analysis (PCA) were used, characterization of the nanoemulsion tested systems and adsorption studies, respectively, which confirmed the results observed in the experimental analyses using diluted NE-OS samples in lower concentrations of Tween 80 (0.5 1.75 ppm)

Processo de trabalho em saúde: uma análise das condições de trabalho dos assistentes sociais no âmbito hospitalar

This paper presents the survey results: PROCEDURE FOR WORK IN HEALTH: an analysis of working conditions of social workers in hospitals. Analyzes the inclusion of social workers in work processes in healthcare, specifically in the public hospital, from the objective conditions of work, according to which materializes professional action. The aim is to understand them from the point of view of its relationship with users and other health professionals through the privatization of health, which prevents the Unified Health System (SUS), limiting the operation of the services and the guarantee of rights. The approach to the reality studied was through theoretical and methodological procedures based on the qualitative and quantitative research, focusing on documentary research, observation, semi-structured interview and the theoretical foundation. It is observed that the inclusion of social workers in this context arises from the demands derived from expressions of social issues, "raw material" of professional work, and the gaps resulting from contradictions in the process of rationalization / reorganization of the SUS, meaning that the needs the population are confronted with the content and form of organization of services. At the hospital, the professional actions are developed through the shift, space contradictory clash between the collective and individual, in which individual activities are prioritized and ad hoc unplanned and reduced to the solution of "problems" of users, through actions assistance in an emergency and bureaucratic. These findings emphasize the inadequacy of space and lack of minimum conditions of service to users, which undertakes the professional with regard to ethical and political principles of the profession, since it is the responsibility and duty of the social guarantee the secrecy and privacy of users what is revealed during the process of professional intervention. The professional social workers is permeated by the diversity of skills and competence; lack of planning activities, by incorporating the institutional discourse at the expense of professional goals, by knowing the Code of Professional Ethics, for small number of professionals, the increasing number informality; by poor working conditions and wages; by discouraging research and participation in social policy councils, as well as professional training

Identificação e comparação entre controle preditivo com modelo não linear e PI sintonizados com PSO em sistema de separação gravitacional de águia-óleo

The separation methods are reduced applications as a result of the operational costs, the low output and the long time to separate the uids. But, these treatment methods are important because of the need for extraction of unwanted contaminants in the oil production. The water and the concentration of oil in water should be minimal (around 40 to 20 ppm) in order to take it to the sea. Because of the need of primary treatment, the objective of this project is to study and implement algorithms for identification of polynomial NARX (Nonlinear Auto-Regressive with Exogenous Input) models in closed loop, implement a structural identification, and compare strategies using PI control and updated on-line NARX predictive models on a combination of three-phase separator in series with three hydro cyclones batteries. The main goal of this project is to: obtain an optimized process of phase separation that will regulate the system, even in the presence of oil gushes; Show that it is possible to get optimized tunings for controllers analyzing the mesh as a whole, and evaluate and compare the strategies of PI and predictive control applied to the process. To accomplish these goals a simulator was used to represent the three phase separator and hydro cyclones. Algorithms were developed for system identification (NARX) using RLS(Recursive Least Square), along with methods for structure models detection. Predictive Control Algorithms were also implemented with NARX model updated on-line, and optimization algorithms using PSO (Particle Swarm Optimization). This project ends with a comparison of results obtained from the use of PI and predictive controllers (both with optimal state through the algorithm of cloud particles) in the simulated system. Thus, concluding that the performed optimizations make the system less sensitive to external perturbations and when optimized, the two controllers show similar results with the assessment of predictive control somewhat less sensitive to disturbances

Implementação de uma arquitetura fuzzy neural em hardware com treinamento online

Computational Intelligence Methods have been expanding to industrial applications motivated by their ability to solve problems in engineering. Therefore, the embedded systems follow the same idea of using computational intelligence tools embedded on machines. There are several works in the area of embedded systems and intelligent systems. However, there are a few papers that have joined both areas. The aim of this study was to implement an adaptive fuzzy neural hardware with online training embedded on Field Programmable Gate Array – FPGA. The system adaptation can occur during the execution of a given application, aiming online performance improvement. The proposed system architecture is modular, allowing different configurations of fuzzy neural network topologies with online training. The proposed system was applied to: mathematical function interpolation, pattern classification and selfcompensation of industrial sensors. The proposed system achieves satisfactory performance in both tasks. The experiments results shows the advantages and disadvantages of online training in hardware when performed in parallel and sequentially ways. The sequentially training method provides economy in FPGA area, however, increases the complexity of architecture actions. The parallel training method achieves high performance and reduced processing time, the pipeline technique is used to increase the proposed architecture performance. The study development was based on available tools for FPGA circuits.