Tratamento de cascalho de perfuração utilizando sistemas microemulsionados

The oil industry is one of the activities that generates more waste to the environment. The drill cuttings is a waste generated in large quantities in the drilling process and that may cause environmental damage such as soil contamination and consequently the contamination of groundwater if disposed of without prior treatment. Arises the need to develop scientific activities and research ways to adapt these wastes the current environmental standards. In the case of solid wastes, the NBR 10004: 2004 of the Brazilian Association of Technical Standards (ABNT) classifies them into class I waste (hazardous) and class II (not dangerous), which determines which wastes may or may not be discarded in the environment without causing environmental impact. This study presents a novel alternative for treating drill cuttings, where this waste was classified as class I (Abreu & Souza, 2005), mainly by removing the n-paraffin present in it, since this arises when using drilling fluids base oil. Using microemulsion systems promotes the removal of this contaminant drill cuttings samples from wells located in Alto do Rodrigues - RN. Initially, we determined the concentration of paraffin using infrared method in samples were extracted with ultrasound, we obtained a paraffin concentration in the range from 36.59 to 43.52 g of paraffin per kilogram of cuttings. Used two microemulsion systems containing two nonionic surfactants from different classes, one is an alcohol ethoxylated (UNTL-90) and the other an nonylphenol ethoxylated (RNX 110). The results indicated that the system UNTL-90 surfactant has better efficiency than the system with RNX 110. The study of the influence of contact time at the extraction showed that for times greater than 25 minutes has a tendency to increase the percentage extraction with increasing contact time. It was also observed that the extraction is fast because at 1 minute contact has 22.7% extraction. The reuse of the microemulsion system without removing the paraffin extracted in previous steps, showed reduction of 29.32 in percentage of extraction by comparing the first and third extraction, but by comparing the first and second extractions reduction is 8.5 in percentage extraction, so the systems reuse optimization can be an option for economically viable removing paraffin from cuttings. The extraction with shaking is more effective in the treatment of cuttings, reaching the extraction percentage of 87.04%, that is, obtaining a drill cuttings with 0.551% paraffin. Using the percentage of paraffin employed in non-aqueous drilling fluids and fluid maximum limit on cuttings for disposal established by the Environmental Protection Agency of the United States (US EPA), one arrives at the conclusion that the level of paraffin on gravel cannot exceed 3.93%. Conclude that the amount of paraffin in the treated cuttings with the microemulsion system with shaking is below the established by US EPA, showing that the system used was efficient in removing the paraffin from the drill cuttings.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

Todo Brasileiro merece nível A : habitação multifamiliar para o programa minha casa minha vida energeticamente eficiente

This thesis describes the theoretical, methodological and programmatic proposal for a multifamily residential building located in the urban expansion area of Parnamirim/RN, inserted in the program Minha Casa Minha Vida and level of energy efficiency "A", as the RegulamentoTécnico de Qualidade (RTQ-R/INMETRO) for residential buildings. The development project initially consists of procedures as the study of theoretical, architectural programming and cases studies. With the delimitation of a field solution, situated between the reference and the context, proposals are studied to determine the solution and architectural detailing of the proposal. The architectural program was built based on the method of Problem Seeking (Peña and Parshall, 2001) and research has highlighted aspects of reducing the environmental impact and of the program Minha Casa Minha Vida , among others. The design process was characterized by the incorporation of aspects reviewed and programmed, seeking them compatible and have an economically viable building, socio-spatial quality and energy efficient. The results show that it is possible to obtain a building that meets the constraints of the program that provides housing and energy efficiency level A - and many other environmental qualities and constructive, particularly through architectural design

Diversidade de macroalgas marinhas bentônicas dos recifes de Maracajaú, área de preservação ambiental dos recifes de corais, Rio Grande do Norte, Brasil

Despite the importance of coral reefs to humanity, these environments have been threatened throughout the world. Several factors contribute to the degradation of these ecosystems. The Maracajaú Reef Complex, in Rio Grande do Norte state is part of the Coral Reefs Environment Preservation Area in northeastern Brazil. This area has been receiving an increasing influx of tourism and the integrity of the local reefs is a matter of concern. In this study, the reef macroalgae communities were studied and compared within two areas distinguished by the presence or absence of tourism activities. Two sample sites were chosen: the first one, where diving activities are intense; and the other, where these practices do not occur. Samples were collected at both sites within a quadrate of 625 cm2 of area randomly thrown 5 times along a 10 meters transect line. Richness, Shannon-Hill diversity and Simpson dominance indices were determined based on biomass data. Similarity between sites was analyzed with Bray-Curtis similarity and distance index. Fifty-eight macroalgae species were observed, including 7 Chlorophyta, 13 Phaeophyta and 38 Rhodophyta. In the non-disturbed site, 49 species were found, while at the disturbed site, there were 42 species. Dictyotaceae and Corallinaceae were the most representative families at the non-disturbed site, and Rhodomelaceae and Dictyotaceae at the disturbed site. The non-disturbed site presented a higher biomass and the greatest richness and diversity indices. In the disturbed site the dominance index was greater and Caulerpa racemosa was the dominant species. The dendogram based on similarity index showed two major clusters, and an isolated element at the center that corresponds to a sample from the disturbed site. In the first cluster, samples from the non-impacted site were predominant and fleshy brown algae were more conspicuous. The second cluster was composed primarily of samples from the impacted site, where C. racemosa and red filamentous and erect calcareous algae associations (turf forming) were observed covering large extensions. These associations are represented by groups of algae adapted to environments where disturbances are frequent. They can grow rapidly on substrate where benthic community was removed and do not allow the establishment of other species. The results of the present study show that tourism activity is an impacting factor that has been causing shifts in macroalgae communities in the Maracajaú Reef Complex

Estudo da substituição de agregados miúdos naturais por pó de pedra em concreto de cimento portland

The sharp consumption of natural resources by the construction industry has motivated numerous studies concerning the application of waste to replace partially or fully, some materials, such as aggregates, thereby reducing the environmental impact caused by the extraction of sand and crushing process. The application of stone dust from crushing process arising as an aggregate for the production of Portland cement concrete is a viable alternative in view of the high cost of natural sands, in addition to the environmental damage which causes its operation to the environment. The stone dust has reduced cost compared to natural sand because it is produced in the beds of their own quarries, which are usually located close to major urban centers. This study examined the feasibility of using stone dust from the crushing of rock gneisses in the state of Bahia, replacing natural quartz sand. In the development of scientific study was conducted to characterize physical and chemical raw materials applied and molded cylindrical specimens , using as reference values Fck 20, Fck 25 and Fck 30 MPa ( resistance characteristic of the concrete after 28 days) in following compositions stone powder: 10%, 30%, 50 %, 100% and 100% with additive. The specimens were cured and subjected to the tests of compressive strength and water absorption, then the samples were subjected to the tests of X-ray diffraction and scanning electron microscopy. The results obtained showed that the composition with 10% stone powder showed the best results regarding the physical and mechanical tests performed, confirming the reduction in compressive strength and increased water uptake increased as the content of the powder stone in the concrete composition

Influência da substituição de areia natural por pó de pedra no comportamento mecânico, microestrutural e eletroquímico de concretos

The construction industry is one of the largest consumers of natural raw materials, and concrete is considered today the most used material wide. This accentuated consumption of natural resources has generated concern with the preservation of the environment, and has motivated various studies related to the use of resid ues, which can partially or entirely substitute, with satisfactory performance, some materials such as the aggregate, and in so doing, decrease the impact on the environment caused by the produced residues. Research has been done to better understand and improve the microstructure of concrete, as well as to understand the mechanism of corrosion in reinforced steel. In this context, this work was developed aiming at discovering the influence of the substitution of natural sand by artificial sand, with rega rd to mechanical resistance, microstructure, and durability. To obtain the electrochemical parameters, an adaptation was made to the galvanostatic electrochemical method to study the corrosion in reinforced steel. Concretes of categories 20 MPa and 40 MPa were produced, containing natural sand, and concretes of the same categories were produced with artificial sand substituting the natural sand, and with the addition of sodium nitrate and sodium chloride. Due to the use of rock dust reject (artificial sand), an evaluation was made of its environmental risk. The results indicate that the concretes of category 20 MPa present a better performance than the concrete made with natural sand, thus making it a viable substitute. For the category 40 MPa, the better performance is from the concrete containing natural sand. The adaptation of the galvanostatic electrochemical technique to the study of the corrosion of reinforced steel within concrete proved to be valid for obtaining electrochemical parameters with a high degree of reliability, considering the number of degrees of freedom

Estudo de reatores eletroquímicos para remoção de Cu2+ , Zn2+, Fenol e BTEX em água produzida

The production of water has become one of the most important wastes in the petroleum industry, specifically in the up stream segment. The treatment of this kind of effluents is complex and normally requires high costs. In this context, the electrochemical treatment emerges as an alternative methodology for treating the wastewaters. It employs electrochemical reactions to increase the capability and efficiency of the traditional chemical treatments for associated produced water. The use of electrochemical reactors can be effective with small changes in traditional treatments, generally not representing a significant additional surface area for new equipments (due to the high cost of square meter on offshore platforms) and also it can use almost the same equipments, in continuous or batch flow, without others high costs investments. Electrochemical treatment causes low environmental impact, because the process uses electrons as reagent and generates small amount of wastes. In this work, it was studied two types of electrochemical reactors: eletroflocculation and eletroflotation, with the aim of removing of Cu2+, Zn2+, phenol and BTEX mixture of produced water. In eletroflocculation, an electrical potential was applied to an aqueous solution containing NaCl. For this, it was used iron electrodes, which promote the dissolution of metal ions, generating Fe2+ and gases which, in appropriate pH, promote also clotting-flocculation reactions, removing Cu2+ and Zn2+. In eletroflotation, a carbon steel cathode and a DSA type anode (Ti/TiO2-RuO2-SnO2) were used in a NaCl solution. It was applied an electrical current, producing strong oxidant agents as Cl2 and HOCl, increasing the degradation rate of BTEX and phenol. Under different flow rates, the Zn2+ was removed by electrodeposition or by ZnOH formation, due the increasing of pH during the reaction. To better understand the electrochemical process, a statistical protocol factor (22) with central point was conducted to analyze the sensitivity of operating parameters on removing Zn2+ by eletroflotation, confirming that the current density affected the process negatively and the flow rate positively. For economical viability of these two electrochemical treatments, the energy consumption was calculated, taking in account the kWh given by ANEEL. The treatment cost obtained were quite attractive in comparison with the current treatments used in Rio Grande do Norte state. In addition, it could still be reduced for the case of using other alternative energy source such as solar, wind or gas generated directly from the Petrochemical Plant or offshore platforms

A importância das redes de relacionamento para se formar uma parceria : um estudo de caso na ALESAT

This paper consists in a study case at the Alesat company, which aims at analyzing how the networks from the former companies Ale and Sat influence the formation of partnerships. The study was based on literature by Burt (1992), Granovetter (1973), Uzzi (1997), Contractor and Lorange (1988), Gulati (1998), Child and Faulkner (1998), and others, to verify how important the social relations were between the companies to the formation of a strategic alliance. The research method we adopted analyzed the first partnership between Ale and Sat and the last one that ended up with the merger of the companies resulting in a new company, Alesat. Semi-structured interviews were conducted in 2008 with the council board of the company. Secondary data were also collected from specific web sites from the area, such as ANP, Sindicom and Fecombustíveis, as well as from important newspapers in the market. The primary data were analyzed through the content analysis technique from Triviños (1987). The secondary data were analyzed through the documental analysis technique from Richardson (1985). This way, through the data collected, it can be concluded that the social ties between the companies were important in the partnership, and among the reasons that made the companies get together, the key one was the fact that the union would make possible to the companies act in regions in which they didn t have too much market share, making them a bigger player nationally wise

O princípio constitucional da eficiência aplicado à outorga e à cobrança da água produzida na exploração petrolífera

Water production is unavoidable during a petrol well s lifetime. The amount of produced water associated with oil varies a lot. It can reach values which account to 50% in volume up to nearly 100%, at the end of the well s economic life. It could be verified that, once the water reaches the productive wells, there must be a management of this produced water. Its destiny is defined after a precise study, after which the best option is chosen between relieving it into the environment, re-injecting it into the producing container or disposing it into non-producing formations. Whichever option is made by the involved professionals, after the necessary analysis, it shall consider, besides the technical and economical aspects, also the alternatives which entail less environmental impact. The purpose of the present research is to conduct a study about the application of the constitutional principle of efficiency on the instruments worked out by the public administration on water management, specifically the water use licence and charging for the use in the management of water resources applicable to water production at the petrol wells. In this attempt, before entering the proper approach of the efficiency of the mentioned instruments, it was necessary not only bring to light the doctrinal perception about the constitutional principle of administrative efficiency, but also make some considerations concerning to the structure of the national water resources management, set by the Federal Constitution (1988) and the federal legislation (9433/97)

Saberes e práticas etnomatemáticas na carcinicultura: o caso da Vila de Rego Moleiro-RN

This study addresses issues related to the mathematical knowledge and practices of the workers of carcinoculture (shrimp farming), associating such knowledge and practices to the conceptual aspects and the academic mathematical language. Our central aim was to investigate and discuss such knowledge and practices in order to contribute towards having the members of this group reflect upon their own working practices. The investigation took as reference the ethnographic research approach during observations and interviews, as well as the analysis and interpretation of the existing cultural aspects on the use of Mathematics in the shrimp farmers daily activities, thus composing the four chapters of this dissertation. Initially, the local-regional context was set in the area where the workers of the shrimp farm reside, also describing our methodological options. After that, the kind of work that was carried out is explained through a brief history of the shrimp-farming activity, including a short discussion on the environmental impacts that result as a consequence of shrimp-farming. We then discuss some theoretical and practical aspects of the Ethnomathematics while field of study and research. At that moment, we make a reflection upon the different kinds of Mathematics, especially stressing the kind of Mathematics being taught in Schools and that being put to practice by identifiable cultural groups. With that in mind, we show the investigated knowledge and practices e some possible systematizations accomplished during the study. In the end, we point out some conclusive propositions based on the implications of our study towards the development of an educational process within the local communities, considering a possible use of the results and conclusions of this study in the classroom activities

Gestão dos resíduos sólidos das contruções prediais na cidade do Natal-RN

The present work has the objective of presenting an investigation about the quantification, classification and destination of the waste of construction and demolition (RCD) in the city of Natal - RN, focusing the aspects of the environmental impacts and the strategic importance of the environmental administration in the earnings of productivity of the companies. Of the environmental point of view the research intends to identify and to quantify the monthly and annual production of RCD in the city, as well as to know the places of deposition of those residues. To reach the objectives of the study, an exploratory and descriptive research was accomplished, using a questionnaire with closed subjects and an open one, applied in 25 entrepreneurs of the branch of the building site, being 21 builders and 4 entrepreneurs of collection companies and removal dumps. As form of analysis of the data, the descriptive analysis was used and of crossing. The production engineering considers important the insert of best production practices and administration of the product in the companies, with views to the increase of your competitiveness, productivity earnings and improvement of the environmental aspects with views to the consumer's satisfaction, in that case the buyer of immobile. The principal results of the investigation demonstrate that there was not great variability of answers with relationship to the interviewees opinion in what he refers to the environmental practices. In your majority the building site interviewees entrepreneurs evidenced the absence of the public power, particularly the city hall of Natal, in the control, fiscalization and creation of mechanisms for a correct destination of RCD, as well as for your reuse and recycle. On the other hand also it was evident that the recycle or the reuse of RCD on the part of the companies is a rare practice and a lot of times inexistent, although the entrepreneurs' of the building site section great majority recognizes that would have won of productivity with the correct and intensive use of such measures

Envelhecimento ambiental em compósitos poliméricos à base de tecidos de reforços híbridos

The utilization of synthetic fibers for plastic reinforcement is more and more frequent and this growing interest requires that their mechanic behavior under the most variable conditions of structural applications be known. The use of such materials in the open and exposed to the elements is one of them. In this case, it becomes extremely necessary to study their mechanical properties (strength, stiffness) and the mechanism of fracture by which the environment aging them out. In order to do that, the material must be submitted to hot steam and ultraviolet radiation exposure cycles, according to periods of time determined by the norms. This study proposal deals with the investigation of accelerated environmental aging in two laminated polymeric composites reinforced by hybrid woven made up of synthetic fibers. The configurations of the laminated composites are defined as: one laminate reinforced with hybrid woven of glass fibers/E and Kevlar fibers/49 (LHVK) and the other laminate is reinforced with hybrid tissue of glass fibers/E and of carbon fibers AS4 (LHVC). The woven are plane and bidirectional. Both laminates are impregnated with a thermofix resin called Derakane 470-300 Epoxy Vinyl-Ester and they form a total of four layers. The laminates were industrially manufactured and were made through the process of hand-lay-up. Comparative analyses were carried out between their mechanical properties by submitting specimen to uniaxial loading tractions and three-point flexion. The specimen were tested both from their original state, that is, without being environmentally aging out, and after environmental aging. This last state was reached by using the environmental aging chamber

Avaliação da remoção de sulfeto de hidrogênio do gás natural em uma coluna de absorção

Natural gas, although basically composed by light hydrocarbons, also presents in its composition gaseous contaminants such as CO2 (carbon dioxide) and H2S (hydrogen sulfide). Hydrogen sulfide, which commonly occurs in oil and gas exploration and production activities, besides being among the gases that are responsible by the acid rain and greenhouse effect, can also cause serious harm to health, leading even to death, and damages to oil and natural gas pipelines. Therefore, the removal of hydrogen sulfide will significantly reduce operational costs and will result in oil with best quality to be sent to refinery, thereby resulting in economical, environmental, and social benefits. These factors highlight the need for the development and improvement of hydrogen sulfide sequestrating agents to be used in the oil industry. Nowadays there are several procedures for hydrogen sulfide removal from natural gas used by the petroleum industry. However, they produce derivatives of amines that are harmful to the distillation towers, form insoluble precipitates that cause pipe clogging and produce wastes of high environmental impact. Therefore, the obtaining of a stable system, in inorganic or organic reaction media, that is able to remove hydrogen sulfide without forming by-products that affect the quality and costs of natural gas processing, transport and distribution is of great importance. In this context, the evaluation of the kinetics of H2S removal is a valuable procedure for the treatment of natural gas and disposal of the byproducts generated by the process. This evaluation was made in an absorption column packed with Raschig ring, where natural gas with H2S passes through a stagnant solution, being the contaminant absorbed by it. The content of H2S in natural gas in column output was monitored by an H2S analyzer. The comparison between the obtained curves and the study of the involved reactions have not only allowed to determine the efficiency and mass transfer controlling step of the involved processes but also make possible to effect a more detailed kinetic study and evaluate the commercial potential of each reagent

Constribuição técnica de um sistema de emulsão inversa a base de óleos vegetais para fluidos de perfuração

The developments in formulating drilling fluids to apply in petroleum fields are based on new technologies and environmental challenges, where the technical performance of a developed drilling fluid is used to produce a minimum environmental impact, showing great economy in costs. It is well known that the potential use of oil-based drilling fluids is limited because these fluids when discharged in the sea do not disperse as much as water-based ones and may form waterproof films in the seabed, having a profound effect on plants and animals living in this environment. The current works have been made in investigating fluids called pseudofluids, which are synthetic ester-based, n-paraffin-based and other fluids formed from inverse emulsion. In this research the principal parameters involved in inverse emulsion process were studied, in laboratory scale, using esters as main component. Others commercial drilling fluids were used as comparative samples, as well as samples from laboratory and field where these drilling fluids are being applied. Concentrations of emulsifier and organophilic clay, which are viscosity donor, were varied to verify the influence of these parameters, in different oil/water ratios (55/45, 60/40, 65/35, 70/30, and 75/25). The salt concentration (NaCl) is an indicative parameter of stability and activity of an esterbased fluid. In this research the salt concentration was varied in 10,000, 20,000, and 50,000 ppm of NaCl. Some rheological properties of the produced fluids were studied, such as: initial gel, plastic viscosity, yield point, and apparent viscosity. Through the obtained rheological measures, the existence of two systems could be verified: fluid and flocculated. It could be noticed that the systems were influenced, directly, by the oil/water ratio and emulsifier, organophilic clay and NaCl concentrations. This study showed the viability to use an ester obtained from a regional vegetable product babaçu coconut oil to obtain an efficient and environmental safe drilling fluid