Formulação de bloco intertravado cerâmico com adição de resíduos urbanos e industriais

The production of waste from urban and industrial activities is one of the factors of environmental contamination and has aroused attention of the scientific community, in the sense of its reuse. On the other hand, the city of Salvador/Ba, with approximately 262 channels, responsible for storm water runoff, produces every year, by the intervention of cleaning and clearing channels, a significant volume of sediments (dredged mud), and thus an appropriate methodology for their final destination. This study aims to assess the influence of incorporation of these tailings in arrays of clay for production of interlocked block ceramic, also known as ceramic paver. All the raw materials from the metropolitan region of Salvador (RMS) were characterized by x-ray fluorescence, x-ray diffraction, thermal analysis (TG and TDA), particle size analysis and dilatometry. With the use of statistical experimental planning technique, ternary diagram was defined in the study region and the analyzed formulations. The specimens were prepared with dimensions of 60x20x5mm³, by uniaxial pressing of 30 MPa and after sintering at temperatures of 900°, 1000º and 1100ºC the technological properties were evaluated: linear shrinkage, water absorption, apparent porosity, apparent specifies mass, flexural rupture and module. For the uniaxial compression strength used cylindrical probe body with Ø 50 mm. The standard mass (MP) was prepared with 90% by weight of clay and 10% by weight of Channel sediment (SCP), not being verified significant variations in the properties of the final product. With the incorporation of 10% by weight of manganese residue (PFM) and 10% by weight of the Ceramic waste (RCB) in the mass default, in addition to adjusting the plasticity due to less waste clay content, provided increased linear firing shrinkage, due the significant concentration of K2O, forming liquid phase at low temperature, contributing to decreased porosity and mechanical resistance, being 92,5 MPa maximum compressive strength verified. After extract test leachate and soluble, the piece containing 10% of the PFM, was classified as non-hazardous and inert material according to NBR10004/04 ABNT. The results showed the feasibility on using waste, SCP, RCB and PFM clay mass, at temperatures above 900ºC, paver ceramic production, according to the specifications of the technical standards, so that to exceed the 10% of the PFM, it becomes imperative to conduct studies of environmental impacts

Propriedade fotoluminescente da ZrO2: Tb+3, Eu+3, Tm+3 obtida pelo método de polimerização de complexos

Recent studies are investigating a new class of inorganic materials which arise as a promising option for high performance applications in the field of photoluminescence. Highlight for rare earth (TR +3 ) doped, which have a high luminous efficiency, long decay time and being able to emit radiation in the visible range, specific to each element. In this study, we synthesized ZrO2: Tb +3 , Eu +3 , Tm +3 nanoparticles complex polymerization method (CPM). We investigated the influences caused by the heat treatment temperature and the content of dopants in zirconia photoluminescent behavior. The particles were calcined at temperature of 400, 500 and 600 ° C for two hours and ranged in concentration of dopants 1, 2, 4 and 8 mol% TR +3 . The samples were characterized by thermal analysis, X-ray diffraction, photoluminescence of measurements and uv-visible of spectroscopies. The results of X-ray diffraction confirmed the formation of the tetragonal and cubic phases in accordance with the content of dopants. The photoluminescence spectra show emission in the region corresponding simultaneous to blue (450 nm), green (550 nm) and red (615 nm). According to the results, ZrO2 particles co-doped with rare earth ions is a promising material white emission with a potential application in the field of photoluminescence

Desenvolvimento de argamassa para restauração utilizando resíduo do polimento do porcelanato

The coatings mortars are essential elements of building structures because they execute an important role in protecting walls and are particularly exposed to aggressive action responsible for its degradation over time. The importance of wall coverings has been the subject of discussion and analysis in the conservation and rehabilitation of old buildings. Are sometimes removed and replaced with inappropriate solutions of constructive point of view or architecture. The most commonly used coatings on walls of old buildings is based on traditional hydraulic lime mortars. The present study aims at the formulation of new lime- based mortars and aerial fine aggregate, in order to contribute to a better field of conservation and restoration mortar coating of old buildings. Residue was used for polishing porcelain as fine aggregate, replacing the aggregate (sand), in percentages 05-30% by mass. We conducted a thorough evaluation of the mortar properties in fresh and hardened state by comparing the performance of the same with a reference mortar. The residue used was characterized as the density, bulk density, and particle size laser, scanning electron microscopy, X-ray diffraction and X-ray fluorescence. Formulations were produced 7, 6 with residue and one commonly used formulation, which served as a reference. In the formulations of lime mortars air (hydrated lime powder CH-I) has been adopted a stroke volume (1:3) with constant binder, was varied and the water / binder and aggregate and waste. For evaluation of mortars fresh, proceeded to consistency analysis, specific gravity, water retention and air content embedded. In the hardened state assays were performed in specific gravity, water retention, modulus of elasticity, tensile strength in bending, compressive strength, water absorption by capillary action, adhesion, tensile strength, resistance to shrinkage and salts by of crystallization trials with resources chloride solution, nitrate and sulfate all sodium in prismatic at 90 days of age, in addition to the micro structural analysis of mortars. Based on the results we can see that the mortar formulated with 10% content of waste and the reference free retraction feature more stable closer to neutrality. The composition of 10% was obtained better performance against the action of the salt crystallization. The mortar with 15% residue obtained better density, lower air content embedded and high capacity for water retention developing good workability. The replacement of 20% of waste generates a satisfactory utilization of resistance to compression, flexion and traction grip the base. And, finally, it can be seen that the mortar with 10, 15 and 20% residual show, in principle, good suitability as coatings, thus enabling a final result consistent with durability, workability and aesthetics developing therefore a material with better performance to repair or replace existing mortars in old buildings

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Síntese e caracterização de catalisadores de LaNiO3 não suportados e suportados em Al2O3 e ZrO2 para a reforma a vapor do metano

Ionic oxides with ABO3 structure, where A represents a rare earth element or an alkaline metal and B is a transition metal from group VIII of the periodic table are potential catalysts for oxidation and good candidates for steam reforming reaction. Different methods have been considered for the synthesis of the oxide materials with perovskite structure to produce a high homogeneous material with low amount of impurities and low calcination temperatures. In the current work, oxides with the LaNiO3 formula had been synthesized using the method of the polymeric precursors. The thermal treatment of the materials took place at 300 ºC for 2h. The material supported in alumina and/or zirconia was calcined at 800 ºC temperature for 4h. The samples had been characterized by the following techniques: thermogravimetry; infrared spectroscopy; X-ray diffraction; specific surface area; distribution of particle size; scanning electron microscopy and thermo-programmed reduction. The steam reforming reaction was carried out in a pilot plant using reducing atmosphere in the reactor with a mixture of 10% H2-Argon, a mass about 5g of catalyst, flowing at 50 mL.min-1. The temperature range used was 50 - 1000 oC with a heating rate of 10 oC.min-1. A thermal conductivity detector was used to analyze the gas after the water trapping, in order to permit to quantify the consumption of hydrogen for the lanthanum nickelates (LaNiO3). The results showed that lanthanum nickelate were more efficient when supported in alumina than when supported in zirconia. It was observed that the methane conversion was approximately 100% and the selectivity to hydrogen was about 70%. In all cases were verified low selectivity to CO and CO2

Aplicação da metodologia de planejamento de experimentos para formulação de massas cerâmicas para telhas

Rio Grande do Norte State stands out as one great producer of structural clay of the brazilian northeastern. The Valley Assu ceramic tiles production stands out obtained from ilitics ball clays that abound in the region under study. Ceramics formulation and the design of experiments with mixture approach, has been applied for researchers, come as an important aid to decrease the number of experiments necessary to the optimization. In this context, the objective of this work is to evaluate the effects of the formulation, temperature and heating rate in the physical-mechanical properties of the red ceramic body used for roofing tile fabrication of the Valley Assu, using design of mixture experiments. Four clays samples used in two ceramics industry of the region were use as raw material and characterized by X-ray diffraction, chemical composition, differential thermal analysis (DTA), thermogravimetric analysis (TGA), particle size distribution analysis and plasticity techniques. Afterwards, they were defined initial molded bodies and made specimens were then prepared by uniaxial pressing at 25 MPa before firing at 850, 950 and 1050 ºC in a laboratory furnace, with heating rate in the proportions of 5, 10 e 15 ºC/min. The following tecnologicals properties were evaluated: linear firing shrinkage, water absorption and flexural strength. Results show that the temperature 1050 ºC and heating rate of 5 ºC/min was the best condition, therefore presented significance in all physical-mechanical properties. The model was accepted as valid based of the production of three new formulations with fractions mass diferents of the initial molded bodies and heated with temperature at 1050 ºC and heating rate of 5 ºC/min. Considering the formulation, temperature and heating rate as variables of the equations, another model was suggested, where from the aplication of design of experiments with mixtures was possible to get a best formulation, whose experimental error is the minor in relation to the too much formulations

Avaliação da biodegradabilidade de petróleo utilizando microrganismos isolados do estuário do Rio Potengi (RN)

The oil activity in the Rio Grande do Norte State (RN) is a permanent threat to coastal ecosystems, particularly mangroves, with the possibility of oil spills. In this context, the objective of this study was to evaluate the potential resistance of the mangrove environment of a possible spill. Were selected and isolated microorganisms degrading oil by the technique of enrichment cultures and formation of a bacterial consortium. The kinetic study of the consortium was held in rotary incubator shaken at 150 rpm and 30° C. Samples were taken at intervals of 4 hours for analysis of cell concentration and surface tension. The biodegradation was monitored using two methods of respirometry: manometric (OxiTop-C ®) and conductivimetry, where the biodegradation of oil was estimated indirectly by oxygen consumption and CO2 production, respectively. Furthermore, it was used a full 2² factorial design with triplicate at central point to the runs that used the conductivimetric methodology.. The technique of enrichment cultures allowed to obtain thirteen bacterial strains. Kinetic study of the consortium, we can showed the absence of the lag phase, reaching a maximum cell concentration of 2.55 g / L at 16 h of cultivation and a reduction on surface tension. When we adopted the methodology of OxiTop-C was detected a band indicating biodegradability (1% oil v/v), however when we used the conductivimetry methodology did not observe any band that would indicate effective biodegradation. By monitoring a process of biodegradation is necessary to observe the methodology will be adopted to evaluate the biodegradation process, since for the same conditions adopted different methodologies can produce different results. The oil-degrading isolates from soils of the mangrove estuary Potengi / RN are largely to be used in bioremediation strategies of these places, in the case of a possible oil spill, or it can be used in the treatment of waste oil generated in saline environments, since they are optimized the conditions of the tests so that the efficiency of biodegradation reach the minimum level suggested by the standarts

Avaliação da biodessulfurização de 4-metildibenzotiofeno por Rhodococus rhodochrous (NRRL B-2149)

Crude oil has between 0.04 up to 5% of sulphur, the higher the oil the higher the sulphur levels. Sulphur usually gives problems such as corrosion in refinery, and once burnt produces SO2 that goes to atmosphere. This work aim to investigate the capacity of Rhodococcus rhodochrous (NRRL B-2149) to metabolize the model compound 4-methyldibenzotiophene (4-MDBT), to remove the sulphur and transform it in 2-hydroxybiphenyl (2-HBF) and sulphite using the 4S pathway. Kynetic runs were carried out in shaker at 120 rpm and 32°C. Samples were taken every 12h to assay substrate consume as well as cells production using HPLC. Results showed that R. rhodochrous NRRL B-2149 can use the 4S pathway in order to remove sulphur without change the carbon chain of the molecule as well as that cells and 4-MDBT affects the product formation. The production of 2-hydroxybiphenyl has interest for industry once it is a potent biocide. However, evaluation is necessary in order to obtain better results compatible with industry needs

Uso e disponibilidade da vegetação lenhosa em comunidades rurais no Rio Grande do Norte

The aim of this study was to test the Ecological Apparency Hypothesis comparing two rural communities in João Câmara (RN) and Remigio (PB), in the Northeast of Brazil. This hypothesis assumes that plants are perceived, known and used by human populations according to their local availability. The most used species would be the ones that are more available in the forest (apparent), and apparently suffer greater pressure of use. Communities were consulted through semi-structured interviews. In Remigio 42 people were interviewed, and 50 in João Câmara. The importance of each species was evaluated considering the distinction between citations from current and potential uses. The ethnobotanical information was associated with phytosociological parameters collected by the point-centered quarter method in forested areas, where 50 transects were distributed in each community, and 4,000 individuals sampled in total. Based on the interviews, 58 useful species were recorded, 42 genera and18 families. In the phytosociological study 30 species, 22 genera and 12 families in João Câmara, In Remígio were identified 34 species, 22 genera and nine families.The species were grouped into 11 categories of use. The ecological appearance was confirmed only in the João Câmara, which best explained the relationship between local availability and use of timber resources. Positive correlations were observed also between the technology category VUpotential and dominance. The point-centered quarter was efficient to test appearance, however, further studies through the point-centered quarter method are recommended

Influência de fatores biopsicossociais sobre a mortalidade de idosos no município de Santa Cruz/RN: um estudo prospectivo

The aging process if characterizes for a complex events network, from multidimensional nature, that encloses biological, social, psychic and functional aspects. The alteration of one or more aspects can speed up the aging process, anticipating limitations and until the death in the aged. For an adjusted confrontation of this question is necessary an interdisciplinary vision, in which the some areas of the knowledge can interact and with this to intervenes of the best possible form. Then, information derived from studies of aspects related to incidence, morbidity-mortality and transition patterns, involved in the health-illness process can more accurately identify risk groups thereby establishing links between social factors, illness, incapacity and death. Thus, this study aimed to identify, by a multidimensional vision, the risk factors of mortality in a coorth of elderly in a city in the interior of the state of Rio Grande do Norte (RN), Brazil. A prospective study carried out in Santa Cruz RN, where 310 elderly were randomly selected to form a baseline. The follow-up was 53 months. The predictive variables were divided into sociodemographic, physical health, neuropsychiatric and functional capacity. The statistical analysis carried out by bivariate analysis, survival analysis, followed by binary logistic regression and Cox regression, in the multivariate analysis, considering significant levels p < 0.05 and confidence interval (CI) of 95%. A total of 60 (19.3%) elderly died during the follow-up, where cardiovascular disease was the main cause. The survival was approximately 24.8 months. The study of general survival showed, at 12, 24, 36, and 48 months of observation, a survival rate of 97%, 54%, 31%, and 5% respectively, with a statistical difference in survival only observed for the variables of cognitive function and Basic Activities of Daily Living. In the logistic regression analysis, the risk factors identified were cognitive deficits (OR = 8.74), poor perception of health (OR = 3.89) and dependence for Basic Activities of Daily Living (OR = 3.96). In the Cox analysis, as well as dependence for Basic Activities of Daily Living (HR = 3.17), cognitive deficit (HR = 4.30) and stroke (CVA) (HR = 3.49) continued as independent risk factors for death. The risk factors found in the study can be interpreted as the primary predictors for death among elderly members of the community. Therefore, improvements in health conditions, with actions towards sustaining an autonomous life with special attention for elderly with cognitive impairment, could mean additional healthy quality of life, resulting in the reduction of premature mortality in this population

Sensibilidade da cinética do zinco e avaliação nutricional em crianças submetidas ao teste venoso de tolerância ao zinco

Objective: The purpose of this study was to investigate the kinetics of this micronutrient in schoolchildren between the ages of 6 and 9 years, of both sexes, and to verify its sensitivity in detecting alterations in body zinc status. Methods: Nutritional assessment was performed by body mass index. Food intake, venous zinc tolerance test and zinc kinetics were carried out before and after 3-month oral zinc supplementation. Results: Of the 42 children studied, 76.2% had healthy weight. Only energy, calcium and fiber intake were suboptimal before and after oral zinc supplementation. Serum zinc and total-body zinc clearance, although at normal levels, increased significantly after zinc supplementation. Conclusion: We concluded, therefore, that kinetics is a sensitive tool for detecting changes in body zinc status, even in children without a deficiency of this mineral. Furthermore, kinetics showed a positive response to supplementation and may be a sensitive parameter to evaluate the efficacy of this therapy

Níveis de homocisteína e desempenho cognitivo em uma amostra populacional de idosos da cidade do Natal-RN

The imprecision of the frontier that separates those cognitive deficits inherent to the human physiological aging process from those which represent the early signs of nervous system degenerative pathologies ,very prevalent among the elderly, has brought attention to the need of studies aiming to establish clinical and/or laboratorial criteria to allow this differentiation. Elderly people living in poor and developing countries are frequently exposed to precarious socioeconomic conditions which facilitate the development of an array of pathologies which have metabolic and nutritional dysfunctions as the established or proposed etiological agents. The levels of certain micronutrients, such as the vitamins B12 and B9 (folic acid), and of some intermediary metabolites, such as homocysteine are being thought of as etiological factors and/or as biological markers of a group of alterations which affect the normal functioning of the nervous system with important reflexes upon cognitive performance. This study aims to investigate the influence of homocysteine, B12 vitamin and folic acid levels on the cognitive performance of the low income elderly population. This transversal study took place in Natal, Rio Grande do Norte State, Brazil, and involved 205 dwelling elderly people, users of the Programa de Saúde da Família, a public healthcare program, maintained by the city s health authorities. A multidimensional questionnaire was used to assess the socio-demographic aspects and the overall health and nutrition conditions. The cognitive performance was measured by the use of the Portuguese version of the Mini Mental State Exam (MMSE). The serum levels of homocysteine, B12 vitamin and folic acid were determined by chemiluminescence. The association between the socio-demographic and serum levels of Hcy, B12 vitamin and folic acid was determined by multiple linear regression. Serum levels higher than 13.5 μmol/l, indicative of hyperhomocysteinemia (HHcy), were found on 25.4% of the sample, being more prevalent in men (p<0.05). Deficitary levels of folic acid (<5ng/mol) and of B12 vitamin (<193 pg/ml) were found on 3.9% and 10.2% of the sample respectively. A negative correlation was found between cognitive performance with both age and HHcy and a positive correlation was found between cognitive performance and schooling. The isolated HHcy R2 values were an explanation to only 4% of the variance of the MMSE scores. However, when associated with schooling and age, this model explains about 25% of this association

Interação competitiva do zinco e ferro após administração oral e venosa de zinco em crianças eutróficas

The aim of this study was to assess the acute and chronic effects of zinc in serum iron profile of children aged 6-9 years in relation to nutritional status and dietary intake. The study participants were 11 children regardless of sex, aged 6-9 years. They were selected from three public schools of the city of Natal, Brazil. Body mass index was used to assess nutritional status. In order to determine the patterns of childhood growth and ideal weight we used the standards of the World Health Organization. The dietary intake assessment was based on information from a three-day prospective food survey. The variables were energy intake, protein, lipids, carbohydrates, fiber, calcium, iron and zinc. All children underwent an intravenous administration of zinc (IVAZn) before and after oral administration of zinc (OAZn) (5 mg Zn / day) for three months. We measured serum iron, hematocrit, hemoglobin and total protein, before and after the use of oral zinc. The analysis of hematocrit, hemoglobin and total protein was performed using standard methods of clinical laboratory. Zinc levels and serum iron were measured by atomic absorption spectrophotometry. The project was evaluated and approved by the Ethics in Research Committee of Federal University of Rio Grande do Norte. Results: All children had normal weight. The consumption of energy, fat, fiber, calcium and iron were below recommended levels. However, the levels of protein and carbohydrates were high. Protein and zinc increased significantly after OAZn. Carbohydrate and protein were elevated in the blood. After OAZn, both protein and zinc increased, being statistically significant. Conclusion: The potential inhibitory effect of physiological or pharmacological doses of zinc on the profile of serum iron was observed in children with healthy weight and aged between 6 and 9 years. This negative effect of zinc did not affect the levels of hematocrit or hemoglobin, and therefore did not cause anemia. This was a multidisciplinary study, involving researchers from medicine, nutrition and pharmacy. This met the requirements of multidisciplinarity of the Post Graduate Program in Health Sciences of Federal University of Rio Grande do Norte.

Intervenção dietoterápica em portadores de lipodistrofia generalizada congênita do Rio Grande do Norte

Congenital generalized lipodystrophy is a rare genetic disease with autosomal recessive inheritance characterized by the generalized absence of subcutaneous adipose tissue and insulin resistance. The aim of our study was to determine the profile of patients with congenital generalized lipodystrophy (Berardinelli-Seip syndrome) through their clinical history, eating habits, and socioeconomic and cultural aspects; assess food consumption and nutritional status of the study group; propose and evaluate a diet therapy model associated to oral supplementation with zinc to help in the control and prevention of metabolic complications associated to the pathology. Initial assessment of food consumption indicated a voracious appetite in all the patients studied. The introduction of zinc reduced appetite, contributing to patient adherence to the food plan proposed. It was also observed that the proposed diet contributed mainly to glycidic control, specifically with respect to HbA1c. The nutritional status of the patients investigated was adequate in terms of body mass index (BMI), arm muscle circumference (AMC), arm muscle area AMA, but triceps skinfold (TSF) indicated serious malnutrition. Our study is unique in the literature and provides important information to the field of nutrition and to individuals with this pathology. Furthermore, it contemplates the interdisciplinary and multidisciplinary requirements of the Postgraduate Program in Health Sciences of the Federal University of Rio Grande do Norte (UFRN), Natal, Brazil

Dimensões da satisfação do paciente geriátrico com a assistência fisioterapêutica

Introdução: Os idosos constituem os maiores consumidores dos serviços de saúde, especialmente os de reabilitação, tornando imprescindível a avaliação da qualidade da assistência fisioterapêutica prestada. A satisfação do paciente tem sido considerada uma das melhores e mais eficazes formas de avaliar o cuidado e direcionar o provedor do serviço para suprir as necessidades e expectativas do paciente-cliente. O objetivo deste estudo foi investigar os principais aspectos (preditores) que contribuem para a satisfação do paciente geriátrico com o tratamento fisioterapêutico ambulatorial. Métodos: Trata-se de um estudo com enfoque epidemiológico, transversal e descritivo de cunho exploratório. Foi utilizado o instrumento de avaliação da satisfação do paciente com a fisioterapia, desenvolvido e validado para a população brasileira por Mendonça em 2007, com uma escala de satisfação do paciente composta por 23 itens. Os dados foram coletados na sala de espera de 29 clínicas de Fisioterapia da rede privada da capital do RN/Brasil e a amostra selecionada de forma não-probabilística constou de 221 pacientes com idade superior a 60 anos, que realizaram entre 5 e 60 sessões de fisioterapia onde os dados foram coletados, deveriam ser usuários de plano de saúde e ter condições cognitivas preservadas. Resultados: A análise fatorial indicou a existência de quatro fatores com autovalor maior que 1: interação pacienteterapeuta (7 itens) α = 0,901; acesso e atendimento de recepcionista e pessoal de apoio (8 itens) α = 0,888; ambiente físico e satisfação global (5 itens) α = 0,835; e conveniência (3 itens) α = 0,711. Os itens com maiores escores de satisfação completa foram os contemplados nos aspectos de interação paciente-terapeuta, especialmente o respeito e a gentileza do fisioterapeuta. As associações realizadas através do teste do Qui-quadrado e regressão logística binária entre a satisfação do paciente e as variáveis sócio-demográficas, percepção do estado de saúde e capacidade funcional demonstraram que a satisfação do paciente idoso associa significativamente com o sexo e estado civil. Os achados revelam que as mulheres mostram-se mais satisfeitas com a fisioterapia. Conclusão: Os aspectos interpessoais demonstraram ser preditores relevantes para assistência fisioterapêutica satisfatória, especialmente na população idosa que requer atenção além do suporte puramente técnico