Otimização da síntese de nanoferritas de nizn dopada com cobre e cobalto

Different compositions of Ni0,5-xCuxZn0,5Fe2O4 and Ni0,5-xCoxZn0,5Fe2O4 0 ≤ x ≤ 0.3 were synthesized ferrite y the citrate precursor method. The stoichiometric compositions were calcined in air at 350°C and then pressed into pellets and toroids. The pressed samples were sintered at temperatures of 1000, 1050 and 1100°C/3h in air control at the speed of heating and cooling. The calcined powders were characterized by XRD, TGA / DTG, FTIR, SEM and vibrating sample magnetometry (VSM) and the sintered samples by XRD, SEM, MAV, density and measurements of permeability and magnetic losses. There was pure phase formation ferrimagnetism applied at all temperatures except for A-I composition at all sintering temperatures and A-II only at a temperature of 1100°C. Crystallite sizes were obtained by Rietveld analysis, nanometer size from 11 to 20 nm for the calcined powders. For SEM, the sintered samples showed grain size between 1 and 10 micrometers. Bulk density (ρ) of sintered material presented to the Families almost linear behavior with increasing temperature and a tendency to decrease with increasing concentration of copper, different behavior of the B Family, where the increase in temperature decreased the density. The magnetic measurements revealed the powder characteristics of a soft ferrimagnetic material. Two processes of magnetization were considered, the superparamagnetism at low temperatures (350°C) and the formation of magnetic domains at higher temperatures. Obtaining the best parameters for P and B-II magnetic ferrites at high temperatures. The sintered material at 1000°C showed a relative permeability (μ) from 50 to 800 for the A Family and from 10 to 600 for the B Family. The samples sintered at 1100°C, B Family showed a variation from 10 to 1000 and the magnetic loss (tan δ) of A and B Families, around of 1. The frequency response of the toroidal core is in the range of 0.3 kHz. Several factors contribute to the behavior of microstructure considering the quantities μ and tan δ, such as the grain size, inter-and intragranular porosity, amount of grain boundary and the aspects of the dynamics of domain walls at high frequencies.

Análise de terrenos na porção setentrional da Província Borborema, NE do Brasil: integração de dados geológicos e gravimétricos

It is presently assumed that the Borborema Province resulted from a complex collisional process associated with the convergent movement of plates, possibly involving amalgamation and accretion of microplates. This process was consolidated at the end of the Brasiliano event. It is investigated the possible limits for the tectonostratigraphic terranes in the northern portion of the province based on an integrated study of geological and gravity data. The study area comprises the portion of the Borborema Province located north of the Patos Lineament, limited by longitudes 33º00 W and 43º29 44"W and latitudes 1º36 S and 8º00 S. A revision of the regional geology allowed to identify areas presenting contrasting geological attributes, possibly representing different terranes whose limits are always shear zones of Brasiliano-age. The Sobral-Pedro II shear zone is the only one undoubtedly presenting geological attributes of sutures zones. The other shear zones are very likely associated with a geodinymic context of accretion, involving oblique collisions (docking), transcurrent and/or transforming sutures, and deep intracrustal shear zones. The gravity data contributed as a tool to identify strong lateral contrasts of density inside the upper crust possibly associated with crustal blocks tectonically juxtaposed. The dominant long wavelength anomaly in the Bouguer anomaly map is an expressive gradient, grossly parallel to the continental margin, caused by density variation across the crust-mantle interface in the transition from the continental crust to the oceanic crust originated by the separation between South America and Africa. Medium to small wavelength anomalies are due to intracrustal heterogeneities such as different Precambrian crustal blocks, Brasiliano-age granites and Mesozoic sedimentary basins. A regional-residual separation of the Bouguer anomaly map was performed in order to enhance in the residual map the effect due to intracrustal heterogeneities. The methodology used for this separation was a robust polinomial fitting. The inversion of residual gravity field resulted in a density contrast map (Δρ), in an equivalent layer that provided more accurated anomalies contours and consolidated the model which the sources of residual anomalies are located in the upper part of the present crust. Based on the coincidence of gravity lineaments in the residual map and Brasiliano shear zones, and using additional geological information, the following shear zones are proposed as limits between terranes: Patos shear zone, Sobral-Pedro II shear zone, Picuí-João Câmara shear zone, Remígio-Pocinhos shear zone, Senador Pompeu shear zone, Tauá shear zone, and Portalegre shear zone. Based on the geological/geophysical information it is attributed a higher level of confidence to the first three proposed limits(Patos, Sobral Pedro II, and Picuí-João Câmara shear zones). From west to east, these shear zones individualize the following terranes: Northwest of Ceará terrane, Central Ceará terrane, Tauá terrane, Orós-Jaguaribe terrane, Seridó terrane, and São José de Campestre terrane. In our study, the Rio Piranhas and Patos terranes are questioned because their previously proposed limits do not present good geological and gravimetric evidences. On the other hand, the previously proposed Cearense terrane is now subdivided into Central Ceará and Tauá terranes. Two residual gravity profiles located in the Seridó belt were interpreted using 2 ½ D direct gravity modeling. The main result of the modeling process is that all anomalies, with the exception of one, can be explained by outcroppring bodies, therefore restricted to the upper part of the present crust

Orientação de falhas presentes em testemunhos de sondagens do campo de Xaréu/bacia do Ceará

A research project is being developed by PPGG/UFRN and PETROBRAS in the Xaréu Oil Field located in Ceará Basin, Northeastern Brazil. The objective of the research is to characterize a fractured carbonate reservoir, the Trairi Limestone, in order to drill a borehole with two horizontal legs taking advantage of the natural fracture system to enhance the oil recovery. The present master thesis is part of this research and its contribution is to estimate fault orientation from unoriented cores, using the method proposed by Hesthammer & Henden (2000). In order to orient a fault cutting a bed observed in the core, the bed should be previously oriented. As additional constraint to orient the bed, we use regional bedding orientation obtained from structure maps of Trairi Limestone. Because the number of cores drilled from the Trairi Limestone was too small, we analyzed all cores from the field. As geologic constraint, we admit that all faults were formed as result of the South America and Africa separation, in the context of a regional dextral strike-slip fault formation. In this context, secondary faults are manly T and R faults according Riedel s classification. We analyzed 236.5 m of cores. The dip of bedding varies from 0o to 8o, being the most frequent value equal to 2o. We interpret this result as evidence that the deformation process was manly ruptil. 77 faults were identified in the cores. These faults strike manly to NW and NE with dips, in general, inside the interval 700 - 900. We suggest that the horizontal legs of the borehole should be oriented to NW and NE in order to improve the probability of intercepting open fractures and faults

Dobramentos distensionais e a geometria da falha de Baixa Grande, Graben de Umbuzeiro, Bacia Potiguar (RN)

In spite of significant study and exploration of Potiguar Basin, easternmost Brazilian equatorial margin, by the oil industry, its still provides an interesting discussion about its origin and the mechanisms of hydrocarbon trapping. The mapping and interpretation of 3D seismic reflection data of Baixa Grande Fault, SW portion of Umbuzeiro Graben, points as responsible for basin architecture configuration an extensional deformational process. The fault geometry is the most important deformation boundary condition of the rift stata. The development of flat-ramp geometries is responsible for the formation of important extensional anticline folds, many of then hydrocarbon traps in this basin segment. The dominant extensional deformation in the studied area, marked by the development of normal faults developments, associated with structures indicative of obliquity suggests variations on the former regime of Potiguar Basin through a multiphase process. The changes in structural trend permits the generation of local transpression and transtension zones, which results in a complex deformation pattern displayed by the Potiguar basin sin-rift strata. Sismostratigraphic and log analysis show that the Baixa Grande Fault acts as listric growing fault at the sedimentation onset. The generation of a relay ramp between Baixa Grande Fault and Carnaubais Fault was probably responsible for the balance between subsidence and sedimentary influx taxes, inhibiting its growing behaviour. The sismosequences analysis s indicates that the extensional folds generation its diachronic, and then the folds can be both syn- and post-depositional

Modelagem estrutural física de semigrábens ortogonais e oblíquos à distenção regional: influência da trama do embasamento e comparação com analógicos no nordeste brasileiro

The physical structural modeling tool is being increasingly used in geology to provide information about the evolutionary stages (nucleation, growth) and geometry of geological structures at various scales. During the simulations of extensional tectonics, modeling provides a better understanding of fault geometry and evolution of the tectonic-stratigraphic architecture of rift basins. In this study a sandbox type apparatus was used to study the nucleation and development of basins influenced by previous structures within the basement, variably oriented as regards to the main extensional axis. Two types of experiments were conducted in order to: (i) simulate the individual (independent) development of half-grabens oriented orthogonal or oblique to the extension direction; (ii) simulate the simultaneous development of such half-grabens, orthogonal or oblique to the extension direction. In both cases the same materials (sand mixed with gypsum) were used and the same boundary conditions were maintained. The results were compared with a natural analogue represented by the Rio do Peixe Basin (one of the eocretaceous interior basins of Northeast Brazil). The obtained models allowed to observe the development of segmented border faults with listric geometry, often forming relay ramps, and the development of inner basins faults that affect only the basal strata, like the ones observed in the seismic sections of the natural analogue. The results confirm the importance of basement tectonic heritage in the geometry of rift depocenters

Avaliação de floculante natural à base de Moringa oleifera no tratamento de água produzida na indústria do petróleo: aplicação da técnica combinada floculação/flotação

The principal effluent in the oil industry is the produced water, which is commonly associated to the produced oil. It presents a pronounced volume of production and it can be reflected on the environment and society, if its discharge is unappropriated. Therefore, it is indispensable a valuable careful to establish and maintain its management. The traditional treatment of produced water, usualy includes both tecniques, flocculation and flotation. At flocculation processes, there are traditional floculant agents that aren’t well specified by tecnichal information tables and still expensive. As for the flotation process, it’s the step in which is possible to separate the suspended particles in the effluent. The dissolved air flotation (DAF) is a technique that has been consolidating economically and environmentally, presenting great reliability when compared with other processes. The DAF is presented as a process widely used in various fields of water and wastewater treatment around the globe. In this regard, this study was aimed to evaluate the potential of an alternative natural flocculant agent based on Moringa oleifera to reduce the amount of oil and grease (TOG) in produced water from the oil industry by the method of flocculation/DAF. the natural flocculant agent was evaluated by its efficacy, as well as its efficiency when compared with two commercial flocculant agents normally used by the petroleum industry. The experiments were conducted following an experimental design and the overall efficiencies for all flocculants were treated through statistical calculation based on the use of STATISTICA software version 10.0. Therefore, contour surfaces were obtained from the experimental design and were interpreted in terms of the response variable removal efficiency TOG (total oil and greases). The plan still allowed to obtain mathematical models for calculating the response variable in the studied conditions. Commercial flocculants showed similar behavior, with an average overall efficiency of 90% for oil removal, however it is the economical analysis the decisive factor to choose one of these flocculant agents to the process. The natural alternative flocculant agent based on Moringa oleifera showed lower separation efficiency than those of commercials one (average 70%), on the other hand this flocculant causes less environmental impacts and it´s less expensive

Uso de metamaterial em antenas de microfita com supercondutor

Metamaterials have attracted great attention in recent decades, due to their electromagnetic properties which are not found in nature. Since metamaterials are now synthesized by the insertion of artificially manufactured inclusions in a specified homogeneous medium, it became possible for the researcher to work with a wide collection of independent parameters, for example, the electromagnetic properties of the material. An investigation of the properties of ring resonators was performed as well as those of metamaterials. A study of the major theories that clearly explain superconductivity was presented. The BCS theory, London Equations and the Two-Fluid Model are theories that support the application of superconducting microstrip antennas. Therefore, this thesis presents theoretical, numerical and experimental-computational analysis using full-wave formalism, through the application of the Transverse Transmission Line – LTT method applied in the Fourier Transform Domain (FTD). The LTT is a full wave method, which, as a rule, obtains the electromagnetic fields in terms of the transverse components of the structure. The inclusion of the superconducting patch is performed using the complex resistive boundary condition. Results of resonant frequency as a function of antenna parameters are obtained. To validate the analysis, computer programs were developed using Fortran, simulations were created using the commercial software, with curves being drawn using commercial software and MATLAB, in addition to comparing the conventional patch with the superconductor as well as comparing a metamaterial substrate with a conventional one, joining the substrate with the patch, observing what improves on both cas

Simulação da destilação molecular de filme descendente para o petróleo

The heavy part of the oil can be used for numerous purposes, e.g. to obtain lubricating oils. In this context, many researchers have been studying alternatives such separation of crude oil components, among which may be mentioned molecular distillation. Molecular distillation is a forced evaporation technique different from other conventional processes in the literature. This process can be classified as a special distillation case under high vacuum with pressures that reach extremely low ranges of the order of 0.1 Pascal. The evaporation and condensation surfaces must have a distance from each other of the magnitude order of mean free path of the evaporated molecules, that is, molecules evaporated easily reach the condenser, because they find a route without obstacles, what is desirable. Thus, the main contribution of this work is the simulation of the falling-film molecular distillation for crude oil mixtures. The crude oil was characterized using UniSim® Design and R430 Aspen HYSYS® V8.5. The results of this characterization were performed in spreadsheets of Microsoft® Excel®, calculations of the physicochemical properties of the waste of an oil sample, i.e., thermodynamic and transport. Based on this estimated properties and boundary conditions suggested by the literature, equations of temperature and concentration profiles were resolved through the implicit finite difference method using the programming language Visual Basic® (VBA) for Excel®. The result of the temperature profile showed consistent with the reproduced by literature, having in their initial values a slight distortion as a result of the nature of the studied oil is lighter than the literature, since the results of the concentration profiles were effective allowing realize that the concentration of the more volatile decreases and of the less volatile increases due to the length of the evaporator. According to the transport phenomena present in the process, the velocity profile tends to increase to a peak and then decreases, and the film thickness decreases, both as a function of the evaporator length. It is concluded that the simulation code in Visual Basic® language (VBA) is a final product of the work that allows application to molecular distillation of petroleum and other similar mixtures.

Buraco negros, correspondência AdS/BCFT e fluido/gravidade

Einstein’s equations with negative cosmological constant possess the so-called anti de Sitter space, AdSd+1, as one of its solutions. We will later refer to this space as to the "bulk". The holographic principle states that quantum gravity in the AdSd+1 space can be encoded by a d−dimensional quantum field theory on the boundary of AdSd+1 space, invariant under conformal transformations, a CFTd. In the most famous example, the precise statement is the duality of the type IIB string theory in the space AdS5 × S 5 and the 4−dimensional N = 4 supersymmetric Yang-Mills theory. Another example is provided by a relation between Einstein’s equations in the bulk and hydrodynamic equations describing the effective theory on the boundary, the so-called fluid/gravity correspondence. An extension of the "AdS/CFT duality"for the CFT’s with boundary was proposed by Takayanagi, which was dubbed the AdS/BCFT correspondence. The boundary of a CFT extends to the bulk and restricts a region of the AdSd+1. Neumann conditions imposed on the extension of the boundary yield a dynamic equation that determines the shape of the extension. From the perspective of fluid/gravity correspondence, the shape of the Neumann boundary, and the geometry of the bulk is sourced by the energy-momentum tensor Tµν of a fluid residing on this boundary. Clarifying the relation of the Takayanagi’s proposal to the fluid/gravity correspondence, we will study the consistence of the AdS/BCFT with finite temperature CFT’s, or equivalently black hole geometries in the bulk.

Desenvolvimento da célula base de microestruturas periódicas de compósitos sob otimização topológica

This thesis develops a new technique for composite microstructures projects by the Topology Optimization process, in order to maximize rigidity, making use of Deformation Energy Method and using a refining scheme h-adaptative to obtain a better defining the topological contours of the microstructure. This is done by distributing materials optimally in a region of pre-established project named as Cell Base. In this paper, the Finite Element Method is used to describe the field and for government equation solution. The mesh is refined iteratively refining so that the Finite Element Mesh is made on all the elements which represent solid materials, and all empty elements containing at least one node in a solid material region. The Finite Element Method chosen for the model is the linear triangular three nodes. As for the resolution of the nonlinear programming problem with constraints we were used Augmented Lagrangian method, and a minimization algorithm based on the direction of the Quasi-Newton type and Armijo-Wolfe conditions assisting in the lowering process. The Cell Base that represents the composite is found from the equivalence between a fictional material and a preescribe material, distributed optimally in the project area. The use of the strain energy method is justified for providing a lower computational cost due to a simpler formulation than traditional homogenization method. The results are presented prescription with change, in displacement with change, in volume restriction and from various initial values of relative densities.

O emprego do imalt como solução interpretativo-composicional em 3 obras autorais para violão

The task of expression undertaken by the performer falls largely on the right hand of guitarist. Aware of this fact, past and present masters have left their contributions to the development of right hand technique. It is clear, with rare exceptions, that educational and interpretative proposals, so far, have addressed the attack on the strings from the flexion of the fingers. This work, however, presents a technical resource called imalt, including in the attack action, the extension movement. Some techniques used in specific circumstances, such as the dedillo, the alzapúa, the tremulo and the rasgueado also use extension movements in the attack. They are put in perspective with the imalt providing a panoramic view of their individual characteristics. The use of imalt in the traditional guitar repertoire is exemplified in Villa Lobos, Ponce and Brouwer. Three pieces were composed for this work: Shravana, Alegoria and Vandana. Compositional techniques such as melodic contour applying and ostinato have been reviewed and used in the preparation of these compositions. A detailed record of compositional trajectory is presented. Therefore, the Model for the Compositional Process Accompaniment according Silva (2007) is used. Some events that have left the imalt in evidence are reported, as the launch and distribution of the Compact Disc (CD) Imalt, publishing scores and interviews. Finally is presented concluding comments, pointing possibilities opened up by this work.

Utilização de um aplicativo de simulação computacional na avaliação de desempenho térmico de protótipo de habitação de interesse social (his)

This Masters Degree dissertation seeks to make a comparative study of internal air temperature data, simulated through the thermal computer application DesignBuilder 1.2, and data registered in loco through HOBO® Temp Data Logger, in a Social Housing Prototype (HIS), located at the Central Campus of the Federal University of Rio Grande do Norte UFRN. The prototype was designed and built seeking strategies of thermal comfort recommended for the local climate where the study was carried out, and built with panels of cellular concrete by Construtora DoisA, a collaborator of research project REPESC Rede de Pesquisa em Eficiência Energética de Sistemas Construtivos (Research Network on Energy Efficiency of Construction Systems), an integral part of Habitare program. The methodology employed carefully examined the problem, reviewed the bibliography, analyzing the major aspects related to computer simulations for thermal performance of buildings, such as climate characterization of the region under study and users thermal comfort demands. The DesignBuilder 1.2 computer application was used as a simulation tool, and theoretical alterations were carried out in the prototype, then they were compared with the parameters of thermal comfort adopted, based on the area s current technical literature. Analyses of the comparative studies were performed through graphical outputs for a better understanding of air temperature amplitudes and thermal comfort conditions. The data used for the characterization of external air temperature were obtained from the Test Reference Year (TRY), defined for the study area (Natal-RN). Thus the author also performed comparative studies for TRY data registered in the years 2006, 2007 and 2008, at weather station Davis Precision Station, located at the Instituto Nacional de Pesquisas Espaciais INPE-CRN (National Institute of Space Research), in a neighboring area of UFRN s Central Campus. The conclusions observed from the comparative studies performed among computer simulations, and the local records obtained from the studied prototype, point out that the simulations performed in naturally ventilated buildings is quite a complex task, due to the applications limitations, mainly owed to the complexity of air flow phenomena, the influence of comfort conditions in the surrounding areas and climate records. Lastly, regarding the use of the application DesignBuilder 1.2 in the present study, one may conclude that it is a good tool for computer simulations. However, it needs some adjustments to improve reliability in its use. There is a need for continued research, considering the dedication of users to the prototype, as well as the thermal charges of the equipment, in order to check sensitivity

Efeitos da dieta hipoprotéica na formação e composição de estruturas dentárias: estudo experimental em ratos Wistar

Protein and caloric malnutrition has been considered one of the most concerned endemic diseases in Brazil and in the world. It has been known that depletion or reduction of proteins as far as meals are concerned can steer irreversible damages upon several organic systems. This study had as aim evaluate the effects the low-protein diet had over the formation and composition of the teeth components. 18 females and 6 males were used for the experiment. 12 from the 18 females had undertaken the low-protein diet (DH) for 03 weeks and the other 6, which remained, and those males had undertaken a controlled diet (DC) for the same period. All animals had the diets during their mating, pregnancy and lactation cycle. As soon as the offsprings had been born, 10 young males and females of each group faced a disease hood analysis to check the teeth germs of their lower fore teeth. The rest of the group had their lactation cycle normally 60 days. Then they were put to death and had their lower fore teeth removed both to be analyzed through a scanning electronic microscopy (SEM) of the structure alterations and to have their calcium checked by an atomic absorption of the phosphorus vanadate-molibdate method and by other minerals EDX method. The animals livers were removed to have their hepatic proteins analyzed as well. The histopatologic study showed that at first day of birth, all animals had their lower fore teeth come out. It was verified that 90% of the animals teeth were in an apposition and calcification period and it was possible to observe the dentin formation from 60% of the 90% already mentioned. Through the SEM method it could be realized that 90% of the animals of the DH group had their lower fore teeth easily broken and no definite shape. In this same group itself, it was also observed long micro fissures 369,66 nm ± 3,45 while the DC group had fissures of 174 nm ± 5,72. Now regarding the calcium and phosphorus concentration, it could be noticed that there was a great reduction of these components and other minerals in the DH group. Almost all minerals, except for the Cl and K, presented higher levels in the DC group enamel.The reduction of the protein input greatly influenced the offsprings´ weight and height. However the hepatic proteins had no important difference between the groups what can make one believe that those animals suffered from protein malnutrition of marasmic kind

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials