51 resultados para Companhias de navegação
Resumo:
Spacecraft move with high speeds and suffer abrupt changes in acceleration. So, an onboard GPS receiver could calculate navigation solutions if the Doppler effect is taken into consideration during the satellite signals acquisition and tracking. Thus, for the receiver subject to such dynamic cope these shifts in the frequency signal, resulting from this effect, it is imperative to adjust its acquisition bandwidth and increase its tracking loop to a higher order. This paper presents the changes in the GPS Orion s software, an open architecture receiver produced by GEC Plessey Semiconductors, nowadays Zarlink, in order to make it able to generate navigation fix for vehicle under high dynamics, especially Low Earth Orbit satellites. GPS Architect development system, sold by the same company, supported the modifications. Furthermore, it presents GPS Monitor Aerospace s characteristics, a computational tool developed for monitoring navigation fix calculated by the GPS receiver, through graphics. Although it was not possible to simulate the software modifications implemented in the receiver in high dynamics, it was observed that the receiver worked in stationary tests, verified also in the new interface. This work also presents the results of GPS Receiver for Aerospace Applications experiment, achieved with the receiver s participation in a suborbital mission, Operation Maracati 2, in December 2010, using a digital second order carrier tracking loop. Despite an incident moments before the launch have hindered the effective navigation of the receiver, it was observed that the experiment worked properly, acquiring new satellites and tracking them during the VSB-30 rocket flight.
Resumo:
Several methods of mobile robot navigation request the mensuration of robot position and orientation in its workspace. In the wheeled mobile robot case, techniques based on odometry allow to determine the robot localization by the integration of incremental displacements of its wheels. However, this technique is subject to errors that accumulate with the distance traveled by the robot, making unfeasible its exclusive use. Other methods are based on the detection of natural or artificial landmarks present in the environment and whose location is known. This technique doesnt generate cumulative errors, but it can request a larger processing time than the methods based on odometry. Thus, many methods make use of both techniques, in such a way that the odometry errors are periodically corrected through mensurations obtained from landmarks. Accordding to this approach, this work proposes a hybrid localization system for wheeled mobile robots in indoor environments based on odometry and natural landmarks. The landmarks are straight lines de.ned by the junctions in environments floor, forming a bi-dimensional grid. The landmark detection from digital images is perfomed through the Hough transform. Heuristics are associated with that transform to allow its application in real time. To reduce the search time of landmarks, we propose to map odometry errors in an area of the captured image that possesses high probability of containing the sought mark
Resumo:
No espaço tridimensional, um corpo rígido qualquer pode efetuar translações e ou rotações em relação a cada um de seus eixos. Identificar com precisão o deslocamento realizado por um corpo é fundamental para alguns tipos de sistemas em engenharia. Em sistemas de navegação inercial tradicionais, utilizam-se acelerômetros para reconhecer a aceleração linear e giroscópios para reconhecer a velocidade angular registrada durante o deslocamento. O giroscópio, entretanto, é um dispositivo de custo mais elevado e com alto consumo de energia quando comparado a um acelerômetro. Essa desvantagem deu origem a pesquisas a respeito de sistemas e unidades de medidas inerciais que não utilizam giroscópios. A ideia de utilizar apenas acelerômetros para calcular o movimento linear e angular surgiu no início da década de 60 e vem se desenvolvendo através de modelos que variam no número de sensores, na maneira como estes são organizados e no modelo matemático que é utilizado para derivar o movimento do corpo. Esse trabalho propõe um esquema de configuração para construção de uma unidade de medida inercial que utiliza três acelerômetros triaxiais. Para identificar o deslocamento de um corpo rígido a partir deste esquema, foi utilizado um modelo matemático que utiliza apenas os nove sinais de aceleração extraídos dos três sensores. A proposta sugere que os sensores sejam montados e distribuídos em formato de L . Essa disposição permite a utilização de um único plano do sistema de coordenadas, facilitando assim a instalação e configuração destes dispositivos e possibilitando a implantação dos sensores em uma única placa de circuito integrado. Os resultados encontrados a partir das simulações iniciais demonstram a viabilidade da utilização do esquema de configuração proposto
Resumo:
We propose in this work a software architecture for robotic boats intended to act in diverse aquatic environments, fully autonomously, performing telemetry to a base station and getting this mission to be accomplished. This proposal aims to apply within the project N-Boat Lab NatalNet DCA, which aims to empower a sailboat navigating autonomously. The constituent components of this architecture are the memory modules, strategy, communication, sensing, actuation, energy, security and surveillance, making these systems the boat and base station. To validate the simulator was developed in C language and implemented using the graphics API OpenGL resources, whose main results were obtained in the implementation of memory, performance and strategy modules, more specifically data sharing, control of sails and rudder and planning short routes based on an algorithm for navigation, respectively. The experimental results, shown in this study indicate the feasibility of the actual use of the software architecture developed and their application in the area of autonomous mobile robotics
Resumo:
Navigation based on visual feedback for robots, working in a closed environment, can be obtained settling a camera in each robot (local vision system). However, this solution requests a camera and capacity of local processing for each robot. When possible, a global vision system is a cheapest solution for this problem. In this case, one or a little amount of cameras, covering all the workspace, can be shared by the entire team of robots, saving the cost of a great amount of cameras and the associated processing hardware needed in a local vision system. This work presents the implementation and experimental results of a global vision system for mobile mini-robots, using robot soccer as test platform. The proposed vision system consists of a camera, a frame grabber and a computer (PC) for image processing. The PC is responsible for the team motion control, based on the visual feedback, sending commands to the robots through a radio link. In order for the system to be able to unequivocally recognize each robot, each one has a label on its top, consisting of two colored circles. Image processing algorithms were developed for the eficient computation, in real time, of all objects position (robot and ball) and orientation (robot). A great problem found was to label the color, in real time, of each colored point of the image, in time-varying illumination conditions. To overcome this problem, an automatic camera calibration, based on clustering K-means algorithm, was implemented. This method guarantees that similar pixels will be clustered around a unique color class. The obtained experimental results shown that the position and orientation of each robot can be obtained with a precision of few millimeters. The updating of the position and orientation was attained in real time, analyzing 30 frames per second
Resumo:
With the increasing industrialization of the planet caused by globalization, it has become increasingly common to search for highly resistant and durable materials for many diverse branches of activities. Thus, production and demand for materials that meet these requirements have constantly increased with time. In view of this, stainless steel is presented as one of the materials which are suitable applications, due to many features that are interesting for several segments of the industry. Concerns of oil companies over heavy oil reservoirs have grown steadily for the last decades. Rheological properties of these oils impair their transport in conventional flow systems. This problem has created the need to develop technologies to improve flow and transport, reducing operation costs so as to enable oil production in the reservoir. Therefore, surfactant-based chemical systems are proposed to optimize transport conditions, effected by reduction of interfacial tensions, thereby enhancing the flow of oil in ducts and reducing load losses by friction. In order to examine such interactions, a study on the wettability of metallic surfaces has been undertaken, represented by measuring of contact angle of surfactant solutions onto flat plates of 304 stainless steel. Aqueous solutions of KCl, surfactants and mixtures of surfactants, with linear and aromatic hydrocarbon chain and ethoxylation degrees ranging between 20 to 100, have been tested. The wettability was assessed by means of a DSA 100 krüss goniometer. The influence of roughness on the wettability was also investigated by machining and polished the stainless steel plates with sandpapers of references ranging between 100 of 1200. The results showed that sanding and polishing plates result in decrease of wettability. As for the solutions, they have provided better wettability of the stainless steel than the KCl solutions tested. It was also been concluded that surfactant mixtures is an option to be considered, since they promote interactions that generate satisfactory contact angles for a good wettability on the stainless steel plate. Another conclusion refers to the influence of the ethoxylation degree of the nonionic surfactant molecules on wettability. It has been observed that contact angles decrease with decreasing ethoxylation degrees. This leads us to conclude that molecules with higher ethoxylation degree, being more hydrophobic, decrease the interaction of water with the ducts, thereby reducing friction and improving the flow
Resumo:
Dengue fever is an infectious disease that causes thousands of deaths each year in Brazil and other tropical countries. This work demonstrates that the irregularity in the supply of water by public water supply systems is a major factor that contributes to the proliferation of breeding sites of the mosquito that transmits dengue, due to the impossibility of removing water storage tanks. 31 points in the water supply network in thirteen districts of Natal, Brazil, were monitored by the installation of pressure gauges type Datalogger. The data about pressure showed deficiency in water supplies in many neighborhoods, forcing residents to accumulate water in tanks at ground level. In addition, It was observed that in neighborhoods with regular water supply, Infestation Index per type of container (ITR) of type A2 (Deposit ground level) was 0.00% and where there were failures in the supply of water , the ITR was high (above 50%). We believe that policies to combat dengue in Brazil should be reassessed so that more resources can be directed to the improvement of water supply systems and supply companies should be blamed for the problem too
Resumo:
The ability to predict future rewards or threats is crucial for survival. Recent studies have addressed future event prediction by the hippocampus. Hippocampal neurons exhibit robust selectivity for spatial location. Thus, the activity of hippocampal neurons represents a cognitive map of space during navigation as well as during planning and recall. Spatial selectivity allows the hippocampus to be involved in the formation of spatial and episodic memories, including the sequential ordering of events. On the other hand, the discovery of reverberatory activity in multiple forebrain areas during slow wave and REM sleep underscored the role of sleep on the consolidation of recently acquired memory traces. To this date, there are no studies addressing whether neuronal activity in the hippocampus during sleep can predict regular environmental shifts. The aim of the present study was to investigate the activity of neuronal populations in the hippocampus during sleep sessions intercalated by spatial exploration periods, in which the location of reward changed in a predictable way. To this end, we performed the chronic implantation of 32-channel multielectrode arrays in the CA1 regions of the hippocampus in three male rats of the Wistar strain. In order to activate different neuronal subgroups at each cycle of the task, we exposed the animals to four spatial exploration sessions in a 4-arm elevated maze in which reward was delivered in a single arm per session. Reward location changed regularly at every session in a clockwise manner, traversing all the arms at the end of the daily recordings. Animals were recorded from 2-12 consecutive days. During spatial exploration of the 4-arm elevated maze, 67,5% of the recorded neurons showed firing rate differences across the maze arms. Furthermore, an average of 42% of the neurons showed increased correlation (R>0.3) between neuronal pairs in each arm. This allowed us to sort representative neuronal subgroups for each maze arm, and to analyze the activity of these subgroups across sleep sessions. We found that neuronal subgroups sorted by firing rate differences during spatial exploration sustained these differences across sleep sessions. This was not the case with neuronal subgroups sorted according to synchrony (correlation). In addition, the correlation levels between sleep sessions and waking patterns sampled in each arm were larger for the entire population of neurons than for the rate or synchrony subgroups. Neuronal activity during sleep of the entire neuronal population or subgroups did not show different correlations among the four arm mazes. On the other hand, we verified that neuronal activity during pre-exploration sleep sessions was significantly more similar to the activity patterns of the target arm than neuronal activity during pre-exploration sleep sessions. In other words, neuronal activity during sleep that precedes the task reflects more strongly the location of reward than neuronal activity during sleep that follows the task. Our results suggest that neuronal activity during sleep can predict regular environmental changes
Resumo:
Natural selection shapes body and behavior of each species. For primates, the social environment constituted one of the greatest selective pressure for the development of their cognition. When we consider gender differences, we see that sexual selection also operates through different selective pressures for men and women not only in physical terms but in terms of cognitive skills. Among these, the primary cognitive abilities - that emerge naturally - and secondary - that rely on an artificial environment for learning - develop differently for each sex, making them suitable for specific tasks in different capacities. Previous studies utilized the Wason Selection Test a conditional logic tool - to measure, among several other things, the ability to recognize violation of rules in abstract contexts and social contexts. Subjects generally had better performance in the latter, however, in these studies possible differences motivated by learning in formal logic or genre were not considered. Our study investigated these two variables, as well as the time spent to solve each task. Furthermore, we used an index to take into account the rights and wrongs of the participants in tasks. We realized that although learning in formal logic does not bring significant differences in solving tests, the gender differences are strongly observed when we consider the social contexts and abstract. Women perform better in social tasks. This can be explained due to different sexual selective pressures for this gender in terms of one-on-one relationships within the group. Men are better at tasks of abstract context and this is probably due to the same reason. Their capabilities for territory defense, habitat navigation and forming coalitions depends on primary cognitive abilities that support secondary cognitive skills of abstraction. Thus, gender differences are a factor to be taken into account in controlling future experiments with the same tool
Resumo:
Numerous studies discuss the issue of adolescent in conflict with the law from the adolescent that committed infraction or from his perceptions. Taking into account the importance of the family in the life of all subject in development, this study sought the look of the families about the infraction of their adolescents under socio-educative measures. For this purpose, semi-open interviews were conducted with 20 families, ten of the boys and equal number of the girls. The institutions where the measures are applied in Natal / RN gave space for most family members to be interviewed. The data collected were arranged in tables and analyzed qualitatively following the socio-historical perspective. The survey revealed that the meanings attributed to the time of conflict with the law of the adolescents differ between the boys families and the girls . Most of the boys families see the infraction as a consequence of the influence of bad company, as a minor provocative of changes in the family s relations, left justified in a context marked by violence. Now for most part of the girls families, the infraction is seen as their responsibility, as generator of transformations within the family both emotional and economic , and inaugurates a search movement for conflicts resolutions. Through the testimonies of these families, it became evident that there was a family reality structured also by a conflicting social, economic and community context. Thus, before there is an infraction that demarcates the conflict in adolescence, there is a family in conflict.
Resumo:
The World Wide Web has been consolidated over the last years as a standard platform to provide software systems in the Internet. Nowadays, a great variety of user applications are available on the Web, varying from corporate applications to the banking domain, or from electronic commerce to the governmental domain. Given the quantity of information available and the quantity of users dealing with their services, many Web systems have sought to present recommendations of use as part of their functionalities, in order to let the users to have a better usage of the services available, based on their profile, history navigation and system use. In this context, this dissertation proposes the development of an agent-based framework that offers recommendations for users of Web systems. It involves the conception, design and implementation of an object-oriented framework. The framework agents can be plugged or unplugged in a non-invasive way in existing Web applications using aspect-oriented techniques. The framework is evaluated through its instantiation to three different Web systems
Resumo:
The widespread growth in the use of smart cards (by banks, transport services, and cell phones, etc) has brought an important fact that must be addressed: the need of tools that can be used to verify such cards, so to guarantee the correctness of their software. As the vast majority of cards that are being developed nowadays use the JavaCard technology as they software layer, the use of the Java Modeling Language (JML) to specify their programs appear as a natural solution. JML is a formal language tailored to Java. It has been inspired by methodologies from Larch and Eiffel, and has been widely adopted as the de facto language when dealing with specification of any Java related program. Various tools that make use of JML have already been developed, covering a wide range of functionalities, such as run time and static checking. But the tools existent so far for static checking are not fully automated, and, those that are, do not offer an adequate level of soundness and completeness. Our objective is to contribute to a series of techniques, that can be used to accomplish a fully automated and confident verification of JavaCard applets. In this work we present the first steps to this. With the use of a software platform comprised by Krakatoa, Why and haRVey, we developed a set of techniques to reduce the size of the theory necessary to verify the specifications. Such techniques have yielded very good results, with gains of almost 100% in all tested cases, and has proved as a valuable technique to be used, not only in this, but in most real world problems related to automatic verification
Resumo:
Created on 3 december 1997, the REMPLAC (Program for Assessment of Mineral Potencial of the Continental Shelf), this porgram aimed to make the basic survey, systematic geological and geophysical continental shelf, detail, at an appropriate scale, sites geo-economic, and perform the analysis and evaluation of mineral deposits. The REMPLAC should continue the efforts of Global Recognition Program of the Brazilian Continental Margin REMAC closed in 1978, the operations Geophysical Sea (GEOMAR) developed by the Directorate of Hydrography and Navigation and the various initiatives of the Program of Marine Geology and Geophysics (PGGM). Despite the high interest on the Amazon platform, there is little information o their morphology and sediment characterization, and in order to fill this gap, the present work samples sedimentological point followed by seismic acquisition. And the studies were to characterize the possible area of interest as being directly influence by tides, which sediments are reworked throughout the platform featuring grain angle with sharp corners, and the carbonate content increases as it approaches the breakdown the platform, and the bodies found outside the foraminifera and mollusks. However, diverging with organic matter that reduces its concentration as it moves away from the coast. The seismic profiles do not get satisfactory results because of low visibility, however, to correlate with the spot samples, of sediment were possible morphological characterization of the area.
Resumo:
The correct distance perception is important for executing various interactive tasks such as navigation, selection and manipulation. It is known, however, that, in general, there is a significant distance perception compression in virtual environments, mainly when using Head-Mounted Displays - HMDs. This perceived distance compression may bring various problems to the applications and even affect in a negative way the utility of those applications that depends on the correct judgment of distances. The scientific community, so far, have not been able to determine the causes of the distance perception compression in virtual environments. For this reason, it was the objective of this work to investigate, through experiments with users, the influence of both the field-of-view - FoV - and the distance estimation methods on this perceived compression. For that, an experimental comparison between the my3D device and a HMD, using 32 participants, seeking to find information on the causes of the compressed perception, was executed. The results showed that the my3D has inferior capabilities when compared to the HMD, resulting in worst estimations, on average, in both the tested estimation methods. The causes of that are believed to be the incorrect stimulus of the peripheral vision of the user, the smaller FoV and the smaller immersion sense, as described by the participants of the experiment.
Resumo:
The objective of the current piece of research presents was draw up a list of recommendations for the site of the Instituto do Cérebro da Universidade Federal do Rio Grande do Norte, with an emphasis on fault identification in usability and information architecture, through the application of design techniques with users of the institution. From the use of the following techniques: Cardsorting, applied to a group of six people as target public, such as professor, administrative technicians and graduate student of the institution; Interviews, carried out with the director of the Instituto do Cérebro, secretaries of the undergraduate and graduate courses; Cooperative Evaluation applied in two ways: in group and individually. The evaluation in group was fulfilled in four sessions that occurred with a group composed of six people who are part of the technical staff of the Instituto do Cérebro. In the Individual Cooperative Evaluation, eight users (graduate students and administrative technicians of the Instituto do Cérebro da UFRN) performed tasks which are frequently fulfilled by users from the public target in the site of the Instituto do Cérebro. After each session of the Individual Cooperative Evaluation, a questionnaire of the user´s satisfaction was used about his or her perception in regard to the site usability and utility of the mentioned institute site. Therefore, it was concluded that, by means of the analysis of the results and the triangulation of the obtained data in each one of the techniques applied with the users, in the present piece of research, problems were verified, among others; all related to the unsuitable use of the interface elements, navigation, labeling of some menu terms, and still, the lack of search space and integration with the social networks – besides the lack, positioning and inappropriate formatting of information that would be of high relevance to the users. Finally, a list of recommendations is presented and this can be used in a future interface redesign with the goal to improve the information architecture and the usability of the site of the Instituto do Cérebro da Universidade Federal do Rio Grande do Norte.