Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Efeito da tecnologia de microondas nas propriedades tecnológicas dos componentes de cerâmica estrutural

O processamento térmico de materiais cerâmicos via energia de microondas, no estágio atual, vem ganhando cada dia mais importância, tendo em vista suas inúmeras aplicações, como por exemplo: aplicação de microondas na área de processamento mineral (aquecimento de minérios antes da moagem, secagem, redução carbotérmica de óxidos minerais, lixiviação, fusão, pré-tratamento de minérios e concentrados de ouro refratário, regeneração de carvão, etc. de acordo com Kigman & Rowson, 1998). Em virtude de uma série de vantagens em potencial, frente aos métodos convencionais de aquecimento, como redução no tempo de processamento; economia de energia; diminuição do diâmetro médio das partículas e melhoramento nas propriedades tecnológicas em geral, esta tecnologia vem se destacando. Neste contexto, o objetivo geral deste trabalho, é desenvolver uma pesquisa visando identificar e caracterizar novas opções de matérias-primas cerâmicas como argilas, feldspatos e caulins que sejam eficazes para definir a formulação de uma ou mais massas para produção de componentes de cerâmica estrutural com propriedades físicas, mecânicas e estéticas adequadas após passarem por sinterização convencional e por energia de microondas destacando as vantagens desta última. Além dos requisitos técnicos e de processo, as formulações apresentadas deverão atender às expectativas de preço e de logística de fornecimento. No estudo foram conformados corpos-de-prova por extrusão e prensagem, sinterizados em fornos microondas e convencional, sob ciclos de queima mais rápidos que os atualmente praticados. As matérias-primas foram caracterizadas e analisadas, utilizando as técnicas de fluorescência por raios X (FRX), difração por raios X (DRX), análise térmica diferencial (DTA), análise térmica gravimétrica (DTG), análise granulométrica (AG), microscopia eletrônica de varredura (MEV), absorção d agua (AA), massa especifica aparente (MEA), porosidade aparente (PA), retração linear (RL) e tensão de ruptura e flexão (TRF). Os resultados obtidos indicaram que as propriedades tecnológicas de Absorção de água (AA) e Tensão de Ruptura e flexão (TRF), proposto no trabalho foram adquiridos com sucesso e estão bem além do limite exigido pelas especificações das normas da ABNT NBR 15.270/05 e 15.310/09

Aditivação de pastas geopoliméricas com tetraborato de sódio e látex não iônico para cimentação de Poços de Petróleo

The development of activities in the oil and gas sector has been promoting the search for materials more adequate to oilwell cementing operation. In the state of Rio Grande do Norte, the cement sheath integrity tend to fail during steam injection operation which is necessary to increase oil recovery in reservoir with heavy oil. Geopolymer is a material that can be used as alternative cement. It has been used in manufacturing of fireproof compounds, construction of structures and for controlling of toxic or radioactive waste. Latex is widely used in Portland cement slurries and its characteristic is the increase of compressive strength of cement slurries. Sodium Tetraborate is used in dental cement as a retarder. The addition of this additive aim to improve the geopolymeric slurries properties for oilwell cementing operation. The slurries studied are constituted of metakaolinite, potassium silicate, potassium hydroxide, non-ionic latex and sodium tetraborate. The properties evaluated were: viscosity, compressive strength, thickening time, density, fluid loss control, at ambient temperature (27 ºC) and at cement specification temperature. The tests were carried out in accordance to the practical recommendations of the norm API RP 10B. The slurries with sodium tetraborate did not change either their rheological properties or their mechanical properties or their density in relation the slurry with no additive. The increase of the concentration of sodium tetraborate increased the water loss at both temperatures studied. The best result obtained with the addition of sodium tetraborate was thickening time, which was tripled. The addition of latex in the slurries studied diminished their rheological properties and their density, however, at ambient temperature, it increased their compressive strength and it functioned as an accelerator. The increase of latex concentration increased the presence of water and then diminished the density of the slurries and increased the water loss. From the results obtained, it was concluded that sodium tetraborate and non-ionic latex are promising additives for geopolymer slurries to be used in oilwell cementing operation

Sistemas de medição de desempenho para projetos de PD&I no Setor de Petróleo e Gás Natural

Organizations are seeking new ideas, tools and methods aiming to improve management process and performance. On the other hand, system performance measurement needs to portray organizational changes and provide managers with a set of true and more appropriate information for the decision-making process. This work aims to propose a performance measurement system in the academic field regarding Research, Development and Innovation (RDI) in the oil and gas industry. The research performed a bibliographic review in a descriptive exploratory manner. A field research was conducted with an expert focus group in order to gather new indicators. As for the validation of these indicators, a survey with experienced professional was also realized. The research surveyed four segments in and outside of the Federal University of Rio Grande do Norte-Brazil such as oil and gas project coordinators, staff at Academic Planning Offices, FUNPEC employees as well as coordinators from Petrobrás. The performance measuring system created from this study features three interrelated performance indicators pointed out as: process indicators, outcome indicators and global indicators. The proposal includes performance indicators that seek to establish more appropriate strategies for effective institution management. It might help policy making of university-industry interaction policies

Proposta de modelo de interação da Universidade Federal do Rio Grande do Norte e empresas do setor de petróleo

Operational procedures may negatively interfere in negotiation and execution regarding universities and business companies. In some cases it may even derail business interaction. Thus, aiming to overcome this and other barriers a university-industry interaction model was structured. The model enhances the appropriation of technological solutions on behalf of enterprises, as well as aim to improve the quality of teaching and research done at the university. In order to conduct a case study, sampling considering the Federal University of Rio Grande do Norte (UFRN) was made as well as the Oil and Gas sector. For data collection questionnaires, classroom observation, document analysis, semi-structured interviews were used. The study describes the companies as well as the internal organization of UFRN in their interaction context. The diagnosis related to past interactions as well as the expectations of the companies and the university s internal subjects regarding the university-industry relationship were also studied. Thus, specific questionnaires were applied for the three types of groups: researchers, managers and business companies. These subjects pointed out that the great deal of barriers they identified were related to issues regarding the university internal management. Given these barriers, the critical factors were then identified in order to overcome this reality. Among the nine critical factors only one belongs to the macro environment, while the remaining factors are related to organizational issues present in the university context. It was possible to formulate a university-business interaction model one the researched focused on the case study results and contribution from a theoretical framework that was enabled trough literature review. The model considers all business collaboration mechanisms; it focuses on a particular strategic productive sector and provides a co-evolution vision over time, according to the sector´s development strategy. The need for institutionalizing the relationship with the companies involved is pointed out. The proposed model considers all the critical factors identified by the research; it aims long-term relationship with the company and integrates teaching, research and extension actions. The model implementation was also considered. It was seen that it must be done in three phases. The phases will be defined by the level of maturity in the relationship between the university and the companies. Thus, a framework was developed in order to assess the interaction level regarding company institutionalization. Whilst structuring the model was a concern with replication came up. It was pointed out that this model should not only serve to this specific case study situation. So the final result is a model of university-industry relationship appropriate in the first instance, for UFRN, but has applicability, in general, to any Brazilian university

Camarão Litopenaeus vannamei: componentes de importância nutricional na carne e nos resíduos do beneficiamento

Farming of marine shrimp is growing worldwide and the Litopenaeus vannamei (L. vannamei) shrimp is the species most widely cultivated. Shrimp is an attractive food for its nutritional value and sensory aspects, being essential the maintenance of this attributes throughout storage, which takes place largely under freezing. The aim of this research was to evaluate quality characteristics of Litopenaeus vannamei shrimp, during freezing storage and to verify the effect of rosemary (Rosmarinus officinalis) adding. Considering the reutilization of processing shrimp wastes, total carotenoids analysis were conducted in waste of Litopenaeus vannamei shrimp and in the flour obtained after dryer. Monthly physicochemical and sensorial analysis were carried out on shrimp stored at 28,3 ± 3,8ºC for 180 days. Samples were placed in polyethylene bags and were categorized as whole shrimp (WS), peeled shrimp (PS), and PS with 0,5% dehydrated rosemary (RS). TBARS, pH, total carotenoid and sensorial Quantitative Descriptive Analysis (QDA) were carried out. Carotenoid total analysis was conducted in fresh wastes and processed flour (0 day) and after 60, 120 and 180 days of frozen storage. After 180 days, RS had lower pH (p = 0.001) and TBARS (p = 0.001) values and higher carotenoids (p = 0.003), while WS showed higher carotenoid losses. Sensory analysis showed that WS were firmer although rancid taste and smell were perceived with greater intensity (p = 0.001). Rancid taste was detected in RS only at 120 days at significantly lower intensity (p = 0.001) than WS and PS. Fresh wastes had 42.74μg/g of total carotenoids and processed flour 98.51μg/g. After 180 days of frozen storage, total carotenoids were significantly lower than 0 day (p<0,05). The addition of rosemary can improve sensory quality of frozen shrimp and reduce nutritional losses during storage. Shrimp wastes and flour of L. vannamei shrimp showed considerable astaxanthin content however, during storage it was observed losses in this pigment

Avaliação da eficácia de um programa de "Escola de Coluna" para lombalgia crônica inespecífica

The Back School has been used to prevent and to treat back pain since 1969, however its effectiveness still is controversy in literature. The objective of this study was to evaluate the effectiveness of a program of "Back School" in patients with nonspecific chronic low back pain, directed by rheumatologists and orthopedic doctors to Physiotherapy School Clinic of Universidade Potiguar (UnP) Natal/RN- Brazil, in period of May/2002 to December/2003. Seventy patients, with age varying from 18 to 60 years, were randomized in two groups: Experimental group (group A) with 34 patients, which was subdivided in groups with 6 to 8 components. This group participated of a theoretician and practical program of Back School with 4 lessons, one day per week, with 60 minutes of duration; to the Control group (group B), with 36 patients, was explained that the group should stay four months in a waiting list . Both groups, had been carried through three evaluations, by a blind, to patient group, independent observer: initial evaluation, after four and sixteen weeks. The following variables were analyzed: pain intensity, measured by analog visual scale (AVS), functional disability, measured by disability questionnaire of Roland and Morris and the spinal mobility measured by Schöber s method. In statistical analysis it was used variance analysis ANOVA, the test of Newman-Keuls multiple comparations, and the Pearson correlation coefficient, with significance level p<0.05. Thirteen patients (18,6%) didn t complete the evaluations, (5 from experimental group and 8 from control group). At last, 57 patients were studied, (29 from Experimental group and 28 from Control group), it was observed a significant statistical improve just for Experimental group in variables pain intensity (p=0,0001), functional disability

Estudo do perfil térmico de fornos do tipo "caipira" utilizados pelo setor de cerâmica vermelha em parelhas na região Seridó-RN

The present study aimed to characterize the thermal profile of wood fired oven used by the red ceramic industry in Parelhas, in the Seridó region/RN, aiming to propose structural interventions that can contribute to increasing productivity and product quality, optimize wood consumption and mitigate existing losses during the burning process. The study was conducted at Cerâmica Esperança in the city of Parelhas -RN, Brazil, during the period from August 2012 to September 2013. Four treatments were performed with three replicates, ie, with, a total of 12 experimental units (burnings). In the first stage 4 treatments were performed with three replicates, totaling 12 experimental units (firings). In the second stage 2 treatments were performed with three replications, totaling 6 experimental units (firings). The physical characteristics of the wood were analyzed using standard NBR 11941 and NBR 7190 for basic density and moisture, respectively. The clay was used as a reference parameter for distinguishing treatments. For both the analysis and characterization was carried out using techniques of fluorescence X (XRF) rays, X-ray diffraction (XRD) analysis, particle size analysis (FA). In the first and second stages were monitored: the time during the firing process, the amount of wood used at each firing, the number of parts enfornadas for subsequent determination of the percentages of losses, but also product quality. To characterize the thermal profile of the oven, we measured the temperature at 15 points scored in the surface charge put into the oven. Measurements were taken every 30 minutes from preheat until the end of burning, using a pyrometer laser sight sighting from preheating until the end of burning. In the second step 12 metal cylinders distributed on the oven walls, and the cylinder end walls 8 of the furnace 2 and rollers on each side walls are installed equidistant to 17 cm from the soil and the surface 30 of the wall are installed. The cylinders distributed on the front were placed 50 cm above the furnace, and the base of the oven 20 cm distant from the ground. 10 also thermocouples were installed, and five thermocouples distributed 1.77 cm above the combustion chambers, and one thermocouple on each side, and three thermocouples in front of the oven. We carried out the measurements of the temperatures every 1 hour during the burning two hours in cooling the cylinders with a pyrometer and thermocouples for dattaloger. These were fixed with depth of 30 cm from the wall. After statistical analysis it was found that: the thermal profile of the furnace surface and at different heights was heterogeneous; and the ranges of density and moisture content of wood are within recommended for use as an energy source standards. We conclude that even at low temperatures reached during firing there was a significant production of good quality products, this is due to high concentrations of iron oxide and potassium oxide found in clay, which lowers the melting point of the piece. The average burn time for each step varied 650-2100 minutes wood consumption was on average 20 m3, product quality was on average 16% of first quality, 70% second, third and 5% to 10% loss . The distance between the wire and the surface of the oven was a significant parameter for all treatments, but with different variations, meaning that the wire should not be so generic and unique form, used as a criterion for completion of the burn process. The central part of the furnace was the area that reached higher temperature, and in a unified manner, with the highest concentration of top quality products. The ideal temperature curve, which provided the highest quality of ceramic products was achieved in the central part of the furnace

Reestruturação do setor industrial e transformação do espaço urbano de Campina Grande PB : a partir dos anos 1990

The central objective of this thesis is studying the changes in the industrial sector of Campina Grande-PB, in the years 1990, about the size of that space and urban sector. The hypothesis that guides this work is that there was a reconfiguration and industrial space in recent years, the result of the restructuring of productive capital and, secondarily, public policies - economic, urban etc. - implemented in the municipality in the years 1990. This reconfiguration industrial meant thepredominance of certain productive segments of the industry and the shift towards urban-industrial areas (industrial districts). This work is guided in these two axes to explain the changes in the industrial campinense and its consequent impact on the urban development of Campina Grande. It is understood by reconfiguration industrial changes in industrial structure, namely the preponderance of one or more productive segments on the other, changing the scenario of production, employment and the number of establishments. In this study, are considered as institutional structures of support and assistance to industry, the various institutions that directly and indirectly, contribute to the development of productive activity. These structures are the first to undergo institutional changes, physical and policies because of intrinsic connection with the industry. The institutional structures contribute to the development of industrial activity and urban development. In Campina Grande, these institutions are important for facilitating the development of certain segments. In this work, sought to identify the current configuration industrial campinense, explaining how the restructuring of production transformed the industry, modifying the urban space in Campina Grande - PB, to direct itself to specific urban areas, from the early 1990

O regime constitucional da contribuição de intervenção do domínio econômico aplicável ao setor de combustíveis

The performance of the State in the economic area is only legitimized when to be given in virtue of the protection of the principles established constitutionally. Thus, the economic intervention of the State prioritizes the formation of a joust economic order and in this context, it fulfills to us to define, to the long one of this work, the contours of the intervention of the State in the economic domain in the presence of the Federal Constitution of the Republic of 05 of October of 1988, and, more specifically, in the petroliferous economic sector by means of the interventive contribution instituted after the Constitutional amendment 33/2001, with Law 10.336/2001. With the creation of this institute, in Brazil, emerged innumerable quarrels concerning its constitutional legitimacy, directing uncurling of the research to the study of the state intervention through this contribution and its constitutional limits, in the purpose to demonstrate the parameters for its institution and application. In this way, the interventive contribution in the fuel sector (CIDE-Combustíveis) shows itself as an intervention instrument on the economic domain, acting in way to finance the indirect performance of the State, specially in what concerns to the promotion of the principle of sustainable development principle. Therefore, CIDE-Combustíveis is an able instrument to concretizes the mentioned constitutional principle. Thus, the division of its incomes promotes the consolidation of the principle of the cooperative federalism. In this direction, from premises of the environmental tax law, this intends to demonstrate the utility and constitutionality of this exaction tax, primordially with regard to the realization of the basic right to the balanced environment

Os conflitos de competência normativa do estado regulador brasileiro no setor administrado pela ANP

The dissertation has by objective describe the administrative activity of regulation exercised by independent regulatory agencies, observing that this activity was already done before this structures creation, however, after a really deep administrative reform that had as objective built a Public Administration with more efficiency, it passed to be done with some own peculiarities of these new structures of regulation. The work gave especial attention to what concern the conflicts of normative competency that really often happen between ANP (Agência Nacional do Petróleo, Gás Natural e Biocombustíveis) and the legislatives organs of the Republic Federative of Brazil, because energetic area has unbelievable mater to any country, and the fact of some juridical norm be against the law and be accepted is very dangerous, it affronts the constitutional principle of the legality e may put in risk the democratic Estate of law, them, regulatory dogmatic must be scientifically knows, and developed, thought and especially there are so many doctrinaires divergences about regulation constitutionality. As a theorist point, the investigation got the Logical nocontradiction principle, according Hans Kelsen and Lourival Vilanova thought, doing a philosophical reflection about the system of positive law, in which there are many antinomies, or conflicts of norms, what include the conflicts of the administrative acts expedited by ANP and the legislation of the brazilian regulatory Estate. For a better understanding and exemplify some perplexities treated by the doctrinaire angle, this work did a lucubration about a possibility of a normative conflict between a ANP resolution and the municipal legislation in a specific case, also, brought several jurisprudences for the brazilians courts of justice, that confirm the empiric existence of normative conflicts among ANP s administrative norms and federal legislation. Finally, concludes observing that the regulation is not a legislative competency delegation to regulatory agencies, is just a new exercise of the administrative function, it is a technical specialization of the public administration, that using this know-how can acting with more efficiency, however the normative power of regulatory agencies must respect the empire of law, so in this terms, the dissertation suggests the ponderation of the constitutionals principles of efficiency and legality how form to harmonizing the democratic legitimate inherent to legal norm supremacy, with the perspective of an efficient economic and institutional development

O dumping ambiental no setor sucroalcooleiro à luz do princípio da livre concorrência

The goal of this study is to investigate about the existence or absence of environmental dumping in the production of fuel ethanol in Brazil, as well as identifying the reasons why the figure of ecological dumping is pernicious to the principles enumerated in constitutional economic order, in particular the principle of free competition. In the twenty-first century environmental issues gained momentum and importance in these terms, which was seen as a mere fallacy given the concern of governments of various countries, after all, environmental protection shows up as the only means of bringing about the maintenance of life at planet. Indeed, it is essential to halt the drastic effects of climate change, and think fast and efficient solutions. Undoubtedly, the contemporary requirements that resulted in the transition to a new economy brings with it the duty of enterprise search for sustainability, and this behavior can not be passive, otherwise it is imperative to work hard and incessant economic agents, even if initially costs are high, this step will ensure a production accountable, transparent and free from accusations of environmental degradation. It is also intended to study the importance of the sector not only as a source of economic growth, but mainly, its contribution to national development, without forgetting that this is devoted in the Constitution of 1988 as one of the objectives of the Federative Republic of Brazil. In fact, the criticism most common perceptions about the production of biofuels, said the interests of the countries producing them in large scale, will eventually generate a exhaustion of soil and a significant increase in food prices. However, the ethanol produced in Brazil is unique in that it is produced from cane sugar, a product is not intended for human or animal, not to mention that the recovery of land just to the rotation with the planting other cultures. It is expected that environmental certifications are useful to demonstrate the quality of ethanol for export and to refute unfounded criticism. Finally, this study will be analyzed further solutions for the plants to develop an economic activity without damaging the environment and in compliance with Brazilian law

Vivências de familiares do paciente internado em unidade de terapia intensiva: estudo fenomenológico

This study originated from my concerns as critical care nurse, regarding the lived experience of the family member of the patient that is hospitalized in the intensive care unit - ICU. The purpose of the study was to comprehend the experience of the family members while having a loved one interned in an ICU, and to identify the common elements of the phenomenon, based on the descriptions of their experiences. Considering that the object of study involves subjective and social questions, the study was conducted using some fundamental ideas of descriptive phenomenology as a referential and the situated phenomenon as suggested by Martins and Bicudo (1989). Ten (10) family members of patients that were interned in the ICU of private hospital in Natal, RN were interviewed using the following leading question: What is it like to have a member of your family interned in the ICU? Five thematic structural categories emerged from the comprehensive analysis of the interviews: Fear of the family member s death; Lack of humanization; Social isolation; Confidence in the ICU; and Overload to the personal life. The description of the phenomenon enabled a new look at how the care team relates to the family members of the patients interned in the ICU, providing some guidance on how to construct a humanized care that involves the family and that is based on affective human relations. This involves a rethinking of the care provided by team to the family and stimulates the reformulation of personal and social attitudes, and of hospital organizational norms

Uma proposta para preparação de pequenas e médias empresas brasileiras prestadoras de serviços ao setor de telecomunicações para implantação da metodologia Seis Sigma

The objective of this work consists of considering a script so that operating companies in the telecommunications sector, mainly small and medium-sized enterprises, can reach excellency in its operations and get, thus, conditions to compete with companies consolidated in its niche of market. The proposal intends to lead the enterprises to a level of qualification of processes that to become them apt to adopt the Six Sigma method as part of its culture. From the analysis of the essential processes of the sector, methods and tools will be suggested for guarantee the continuous improvement of these processes, without forgetting the internal peculiarities of each company

Inovação e gestão do conhecimento no setor petrolífero do RN

Este trabalho apresenta um estudo da Gestão do Conhecimento (GC) no sistema petrolífero do Rio Grande do Norte, considerando possíveis inovações resultantes dessa gestão. Inicialmente, foi feita uma abordagem com relação as características do sistema de petróleo e gás do RN, com base em conceitos disponíveis na literatura. Visou atender aos seguintes objetivos: diagnosticar a rede de empresas do setor petrolífero do RN, identificando qual o estágio de GC em que elas se encontram; identificar e avaliar as práticas de GC utilizadas internamente na Petrobras e nas suas interações dentro da aglomeração; caracterizar a ocorrência das relações entre a UFRN (Universidade Federal do Rio Grande do Norte) x Petrobras. Para alcançar tais objetivos foi desenvolvido um formulário baseado em indicadores de GC e na PINTEC2005 (IBGE), o qual foi aplicado em três grupos: PETROBRAS, Fornecedores da PETROBRAS e UFRN. Como resultados obtidos têm-se: uma análise da GC na PETROBRAS, da GC nos Fornecedores e da cooperação para inovação entre os participantes do sistema, sendo apresentado um estudo da parceria para inovação entre a UFRN x PETROBRAS. Conclui-se que o sistema é uma aglomeração e que apresenta características de um Cluster. Conclui-se ainda que a GC na PETROBRAS encontra-se em fase avançada de implantação no âmbito da corporação, e a parceria entre UFRN e Petrobras pode ser utilizada como modelo de sucesso de integração entre empresas e instituições de pesquisa. Ao final são apresentados, em especial, os resultados obtidos com relação à gestão do conhecimento para a inovação na rede de empresas que operam o sistema petrolífero no Rio Grande do Norte, objetivo principal desta dissertação