Obtenção de uma porcelana dielétrica a partir de matérias-primas do Rio Grande do Norte

The dielectric porcelain is usually obtained by mixing various raw materials proportions and is used in the production of electronic equipment for various applications, from capacitors of high and low Power to insulators for low, medium, high and extra high voltage, which are used in distribution lines and transmission of electricity.This work was directed to the s tudy of technological properties of technic porcelain, made from raw materials extracted from pegmatites found in the regions of Seridó and the Alto Oeste of Rio Grande do Norte, which are made of kaolin, quartz and feldspar, abundant and high quality in these regions. The technic ceramics were obtained by mixing in appropriate levels, kaolin, feldspar, quartz and clay, the last item from a pottery in the city of Sao Gonçalo do Amarante, Rio Grande do Norte. During the development the following characterizations correlated to raw materials were made: laser particle sizing, x-ray diffraction, DTA and TG. The compositions studied were formed by uniaxial pressing at a pressure of 50 MPa and sintered at temperatures ranging from 1150 to 1350ºC and levels (times) of sintering between 30, 60, 90 and 120 minutes. The characterization of the samples were taken from the analysis of weight loss, linear shrinkage, porosity, stoneware curve, bulk density, flexural strength of three points, SEM and X-ray diffraction, TMA, Dielectric and cross Resistivity. The studied materials can be employed in producing the objects used in electrical engineering such as: insulators for low, medium and high-voltage electrical systems, command devices, bushing insulation for transformers, power capacitors, spark plugs, receptacles for fluorescent and incandescent light bulbs and others

Otimização de vazão de poços injetores em projeto de injeção de água utilizando simulação por linhas de fluxo

Until the early 90s, the simulation of fluid flow in oil reservoir basically used the numerical technique of finite differences. Since then, there was a big development in simulation technology based on streamlines, so that nowadays it is being used in several cases and it can represent the physical mechanisms that influence the fluid flow, such as compressibility, capillarity and gravitational segregation. Streamline-based flow simulation is a tool that can help enough in waterflood project management, because it provides important information not available through traditional simulation of finite differences and shows, in a direct way, the influence between injector well and producer well. This work presents the application of a methodology published in literature for optimizing water injection projects in modeling of a Brazilian Potiguar Basin reservoir that has a large number of wells. This methodology considers changes of injection well rates over time, based on information available through streamline simulation. This methodology reduces injection rates in wells of lower efficiency and increases injection rates in more efficient wells. In the proposed model, the methodology was effective. The optimized alternatives presented higher oil recovery associated with a lower water injection volume. This shows better efficiency and, consequently, reduction in costs. Considering the wide use of the water injection in oil fields, the positive outcome of the modeling is important, because it shows a case study of increasing of oil recovery achieved simply through better distribution of water injection rates

Aspectos ambientais e sociais envolvidos na transmissão da L. chagasi no município de Parnamirim/RN

Visceral leishmaniasis hás adapted in the past 20 years to periurban and urban areas, and in Natal, Rio Grande do Norte, it became endemic. Thid study aimed to evaluate the environmental and social aspectsof Leishmania chagasi infection and its epidemiologic transmission chain in an urban, periurban and rural area of Parnamirim-RN. A study with three sections was conducted: Section 1: Sectional study of the human and canine infection by L. chagasi and its environmental and social determinants. Section 2: Observational longitudinal cohort to evaluate the dynamics of the canine infection. Section 3: Longitudinal study to evaluate the behavior of Lu. Longipalpis vector and the seasonal factors related to its dynamics. To include in the study the hauses were randomly selected and georreferenciated. Montenegro skin test was done in the human population and blood samples were collected for anti-Leishmania antibody detection. The canine population was examinated for L. chagasi infection by RIFI, ELISA and ELISA for rK39. An entomologic surveillance was monthly done with CDC light trapsin 10 houses of each locality. Quantitative and qualitative analyses was done using STATISC 6.0. Probality and prediction maps were done using ArcGis 9.0 model. In the human population L. chagasi infection was associated with the area of the hause, age, sex, population densyti, vegetation, kind of the floor of thr hause, water and resides destiny. In the canine population L. chagasi infection was associated with the breed, size, time of living in the hause, presence of dogs in the neighborhood, presence of horses and donkeys in the neighborhood, vegetation, kind of the floor and walls of the hause. The human infection was associated with canine infction only when analyzed taking into account the locality. In the prospective study, serum conversion and antibody lost observed in 30,8% and 22% of the animals examined, respectively. The human infection rate by L. chagasi was 24,6%, by the presence of anti-Leishmania antibody and 38,6% by the Montenegro skin test. The canine infection rate 32,5% by the presence of anti-Leishmania antibody. The vector Lu longipalpis showed an atypical behavior. These results indicate that environmental and social factors are important variables associated with L. chagasi infection in humans and canines, with punctual association of thr last two. Control measures of the infection on the studied points are necessary, in the aim to reduce the endemic focus of the disease in the study area. This research was carried out in a multidisciplinary involving the categories of: doctor, biologist, veterinarian, statistical, pharmaceutical and biochemical

Dores e cores nas mal traçadas linhas dos devotos do Padre Cícero: as trocas linguísticas instauradas entre o discurso eclesial e o discurso epistolar dos romeiros

This study is concerned with analyzing the letters sent by the devotees tothe religious patriarch, Father Cicero, checking as is the relationship of linguistic exchanges between the pilgrims and the Father Cicero through the issuance of letters; and, between the Church and the pilgrims, through homilies uttered these devotees, focusing on the appeals contained therein, for, then, to define a parameter between the requirements contained in the letters and the religious discourse of the Church workers in the liturgical celebrations in view of social and religious demands of the market in question. Our purposes resided in understanding the causes that lead to the production of the letters by devotees, holding us in prayers of intercession to the Father Cicero. Finally, check and understand how is the process of inter - relationship between the writing of devotee and the clerical discourse, with regard to meeting this demand, noting especially the game force a religious field, based on postulates of Pierre Bourdieu (2008), to conceive the communicative act as linguistic exchanges, surpassing the sign and therefore decipherable speech character as well as the interactive strength of the wording and voice advocated by Paul Zumthor (2010) e Bakhtin (2006). Regarding the composition of the corpus, were determined, as the universe of research, letters of pilgrims, sent to Father Cicero, deposited in his own tomb, as well as in the Church of the Horto (Gethsemane) in Juazeiro do Norte-CE (Brazil); beyond religious sermons intended for pilgrims during the massin pilgrimage time

Corpo e escrita: linhas e entrelinhas da produção de conhecimento em sala de aula

Body and writing: Lines and between-lines of production of knowledge in the classroom it is an ethnographic research, longitudinal character, based on experience while experienced educator of the Escola Municipal Professor Amadeu Araújo, located in the city of Natal-RN, from which are made reflections about texts written by students who have distorted age/education level, in the process of literacy. Here as initial goal: to discuss the production of students writing as a process body, considering the record of experiences and the impressions they have made during the teaching process. We initially by a conception of phenomenological body, by understanding it in its complexity, a phenomenon that is made from its relationship with the world and with the Other. The records examined were produced between the year 2000 and 2005 involving writings of 106 students, constituting a universe of 136 texts, from which, delimited a corpus of 27 texts. The relevance with respect to the theme and recurrence in which they were detected, were up to elements that allowed a systematization methodology, defining the following units of analysis: Body, written in everyday; body, written and sexuality; body, written and enjoyment poetics; body, writing and other stories. We used the techniques of search, participant observation, based on the actions and interactions body expressed during the experiment and the analysis of documents that consisted of students in the texts and secondary sources, among them, the records of daily class, reports and projects developed, as well as reports of my pedagogical practice, as a researcher inserted in the investigative process. The experience developed, showed a writing school able to express nuances of human complexity, showing that learning is made in the action body, crossed by various forms of language and pointing to the relevance of a pedagogical work able to articulate the dialogue between the written and registrations body of the students, as subjects of learning

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Otimizações da transmissão de imagens em redes de sensores visuais sem fio explorando a relevância de monitoramento dos nós fontes e codificação DWT

The development of wireless sensor networks for control and monitoring functions has created a vibrant investigation scenario, covering since communication aspects to issues related with energy efficiency. When source sensors are endowed with cameras for visual monitoring, a new scope of challenges is raised, as transmission and monitoring requirements are considerably changed. Particularly, visual sensors collect data following a directional sensing model, altering the meaning of concepts as vicinity and redundancy but allowing the differentiation of source nodes by their sensing relevancies for the application. In such context, we propose the combined use of two differentiation strategies as a novel QoS parameter, exploring the sensing relevancies of source nodes and DWT image coding. This innovative approach supports a new scope of optimizations to improve the performance of visual sensor networks at the cost of a small reduction on the overall monitoring quality of the application. Besides definition of a new concept of relevance and the proposition of mechanisms to support its practical exploitation, we propose five different optimizations in the way images are transmitted in wireless visual sensor networks, aiming at energy saving, transmission with low delay and error recovery. Putting all these together, the proposed innovative differentiation strategies and the related optimizations open a relevant research trend, where the application monitoring requirements are used to guide a more efficient operation of sensor networks

Um estudo de estruturas com PBG e fotônica

One of the objectives of this work is the ana1ysis of planar structures using the PBG (photonic Bandgap), a new method of controlling propagation of electromagnetic waves in devices with dielectrics. Here the basic theory of these structures will be presented, as well as applications and determination of certain parameters. In this work the analysis will be performed concerning PBG structures, including the basic theory and applications in planar structures. Considerations are made related to the implementation of devices. Here the TTL (Transverse Transmission Line) method is employed, characterized by the simplicity in the treatment of the equations that govern the propagation of electromagnetic waves in the structure. In this method, the fields in x and z are expressed in function of the fields in the traverse direction y in FTD (Fourier Transform Domain). This method is useful in the determination of the complex propagation constant with application in high frequency and photonics. In this work structures will be approached in micrometric scale operating in frequencies in the range of T erahertz, a first step for operation in the visible spectra. The mathematical basis are approached for the determination of the electromagnetic fields in the structure, based on the method L TT taking into account the dimensions approached in this work. Calculations for the determination of the constant of complex propagation are also carried out. The computational implementation is presented for high frequencies. at the first time the analysis is done with base in open microstrip lines with semiconductor substrate. Finally, considerations are made regarding applications ofthese devices in the area of telecommunications, and suggestions for future

Acoplador e linha de lâmina unilateral e bilateral com substrato fotônico

The aim of this work is to characterize and use the characteristic parameters of the planar structures constructed with fin lines looking for their applications in devices, using PBG Photonic Band Gap photonic materials as substrate, operating in the millimeter and optic wave bands.The PBG theory will be applied for the relative permittivity attainment for the PBG photonic substrate s and p polarizations. The parameters considered in the structures characterization are the complex propagation constant and the characteristic impedance of unilateral and bilateral fin lines that were obtained by the use of the TTL Transverse Transmission Line Method, together with the Method of the Moments. The final part of this work comprises studies related to the behavior of the asymmetric unilateral fin line coupler with photonic substrate. This research opens perspectives for new works in this modern area. Numerical results are shown by means of bi-dimensional and three-dimensional graphics. Conclusions and suggestions for future works are also presented

Eu não vi, eles me contaram. Uma experiência de transmissão e recepção oral no cotidiano dos sem-terra

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Sair curado para a vida e para o bem: diagramas, linhas e dispersão de forças no complexus nosoespacial do Hospital de Caridade Juvino Barreto (1909-1927)

This work has as object of study the Hospital de Caridade Juvino Barreto, nosocomial institution located in the city of Natal (RN), between the Praia de Areia Preta and the Monte Petrópolis, focusing on the period from 1909, the year in which the new hospital building was constructed and opened, and 1927, the date of the transfer of administration of the public domain to the newly created Sociedade de Assistência Hospitalar (SAH). We study the conditions of possibility of the emergence of this hospital space in the urban environment of the capital of Rio Grande do Norte, seeking to understand the different tactics and strategies implemented by the historical subjects involved in the formation of this institution nosocomial. Starting from a corpus of documents consisting of medical memories (with Dr. Januário Cicco as privileged observer), information present in newspapers (the Republic and the Christmas Journa l), photo collection and extensive administrative and legal material (Speeches, Exhibitions, Reports, Laws and Resolutions), we analyzed in detail the medical geography of HCJB, relating the discourses of medicine and geography in choosing the spatial location of the hospital as we examine the architecture of the hospital, its inner spat iality, divisions, forms of space control, and, finally, we discuss the medical practices that took place within it, leading us in this regard, from the experiences of clinical hospital chief, Dr. Januário Cicco, especially the discussion on "ethics" in hospital work. The perception of HCJB as medical nosoespaciality always on the move, incorporated under taxonomic principles based on difference and dispersion forces, led us to articulate it theoretically from the conceptual-methodological arsenal of philosopher Michel Foucault, particularly his reflections of genealogical phase, focusing on the phenomenon of power, a position that allows us to enhance our space-hospital construction, invention, product of power relations, which give the unfinished aspect nosocômio, apparent, always at stake, perpetual non-modeling possibility has previously defined array, establishing it at the field of possible, of virtuality, of power: hospital that could have been and that it was not. Indeed, the investigation of various aspects/elements of hospital space Juvino Barreto revealed us new dimensions of hospital space, far more complex than the simple and the current idea of a place to shelter patients: plasticity and fluidity of space, which is not made to circumscribe the limits of empeiria, engraving up to strength relations fought between different subject; its Constitution as a transitional space, Heterotopic, doing live inside modern elements with premoderns (professional doctors working with religious thought, skeptical of positivist medicine living with the religious faith of the nuns of Santana); the impossibility of thinking hospital space of HCJB while homogeneous unit, static, transistoric, making the spatiality, without considering the profound differences, fractures and dislocations that animated his own existence, multiplying their expressions of identity

Alterações na evocação de uma memória aversiva ao liongo do ciclo estral de ratas: influências da transmissão gabaérgica na amígdala

GABAergic neurotransmission has been implicated in many aspects of learning and memory, as well as mood and anxiety disorders. The amygdala has been one of the major focuses in this area, given its essential role in modulating emotionally relevant memories. However, studies with male subjects are still predominant in the field. Here we investigated the consequences for an aversive memory of enhancing or decreasing GABAergic transmission in the basolateral nucleus of the amygdala (BLA). Wistar female rats were trained in the plus-maze discriminative avoidance task, in which they had to learn to avoid one of the enclosed arms where an aversive stimulus consisting of a bright light and a loud noise was given (day 1). Fifteen minutes before the test session (day 2) animals received 0,2 μL infusions of either saline solution, the GABAergic agonist muscimol (0,05 mg/ml), or the GABAergic antagonist bicuculine (0,025 mg/ml) bilaterally intra-BLA. On the test day, females in proestrous or estrous presented adequate retrieval and did not extinguish the task, while females in metestrous or diestrous presented impaired retrieval. In the first group, muscimol infusion impaired retrieval and bicuculline had no effect, suggesting naturally low levels of GABAergic transmission in the BLA of proestrous and estrous females. In the second group, muscimol infusion had no effect and bicuculline reversed retrieval impairment, suggesting naturally high levels of GABAergic transmission in the BLA of metestrous and diestous females. Additionally, proestrous and estrous females presented higher anxiety levels compared to metestrous and diestrous females, which could explain better performance of this group. On the other hand, BLA GABAergic system did not interfere with the innate fear response because drug infusions had no effect in anxiety. Thus, retrieval alterations caused by the GABAergic drugs were probably related specifically to memory processes

O uso de analogias para o ensino de equilíbrio químico no ensino médio: facilitação da aprendizagem ou transmissão de erros conceituais?

The use of analogies in high school is often useful for chemistry teaching, either on textbooks or by teachers in the classroom.This use is justified by the large number of abstract concepts that rules this course. Analogies are conceptualized by several authors, which converge on the idea that these are tools that seek a way to elucidate an unknown concept by comparing it to a familiar one, relating their similar and dissimilar features. An analysis on a survey of analogies found in high school chemistry textbooks and chemical equilibrium studies is performed in order to verify whether they are leading to misconceptions for their use by students and/or for their use by teachers in the classroom, or whether they promote a learning facilitation

Uma estratégia dirigida a modelos e baseada em linguagem de descrição arquitetural para linhas de produtos de software

Model-oriented strategies have been used to facilitate products customization in the software products lines (SPL) context and to generate the source code of these derived products through variability management. Most of these strategies use an UML (Unified Modeling Language)-based model specification. Despite its wide application, the UML-based model specification has some limitations such as the fact that it is essentially graphic, presents deficiencies regarding the precise description of the system architecture semantic representation, and generates a large model, thus hampering the visualization and comprehension of the system elements. In contrast, architecture description languages (ADLs) provide graphic and textual support for the structural representation of architectural elements, their constraints and interactions. This thesis introduces ArchSPL-MDD, a model-driven strategy in which models are specified and configured by using the LightPL-ACME ADL. Such strategy is associated to a generic process with systematic activities that enable to automatically generate customized source code from the product model. ArchSPLMDD strategy integrates aspect-oriented software development (AOSD), modeldriven development (MDD) and SPL, thus enabling the explicit modeling as well as the modularization of variabilities and crosscutting concerns. The process is instantiated by the ArchSPL-MDD tool, which supports the specification of domain models (the focus of the development) in LightPL-ACME. The ArchSPL-MDD uses the Ginga Digital TV middleware as case study. In order to evaluate the efficiency, applicability, expressiveness, and complexity of the ArchSPL-MDD strategy, a controlled experiment was carried out in order to evaluate and compare the ArchSPL-MDD tool with the GingaForAll tool, which instantiates the process that is part of the GingaForAll UML-based strategy. Both tools were used for configuring the products of Ginga SPL and generating the product source code