Modelagem de máquina de indução trifásica sem mancais com bobinado dividido

This work presents a model of bearingless induction machine with divided winding. The main goal is to obtain a machine model to use a simpler control system as used in conventional induction machine and to know its behavior. The same strategies used in conventional machines were used to reach the bearingless induction machine model, which has made possible an easier treatment of the involved parameters. The studied machine is adapted from the conventional induction machine, the stator windings were divided and all terminals had been available. This method does not need an auxiliary stator winding for the radial position control which results in a more compact machine. Another issue about this machine is the variation of inductances array also present in result of the rotor displacement. The changeable air-gap produces variation in magnetic flux and in inductances consequently. The conventional machine model can be used for the bearingless machine when the rotor is centered, but in rotor displacement condition this model is not applicable. The bearingless machine has two sets of motor-bearing, both sets with four poles. It was constructed in horizontal position and this increases difficulty in implementation. The used rotor has peculiar characteristics; it is projected according to the stator to yield the greatest torque and force possible. It is important to observe that the current unbalance generated by the position control does not modify the machine characteristics, this only occurs due the radial rotor displacement. The obtained results validate the work; the data reached by a supervisory system corresponds the foreseen results of simulation which verify the model veracity

Indução de morte celular em células de adenocarcinoma cervical humano (HeLa) pela lectina da esponja Cinachyrella apion (CaL)

Cancer is a term used to represent a set of more than 100 diseases, including malignant tumors from different locations. The malignancies are the second leading cause of death in the population, representing approximately 17% of deaths of known cause. Strategies that induce differentiation have had limited success in the treatment of established cancers. In this work, a lectin purified from the marine sponge Cinachyrella apion (CaL) was evaluated due to its hemolytic, cytotoxic and antiproliferative properties, besides the ability to induce cell death via apoptosis in tumor cells. The antiproliferative activity of CaL was tested against cell lines, with the highest inhibition of tumor growth for HeLa, reducing cell growth at a dose dependent manner, with a concentration of 10 μg/mL. The hemolytic activity and toxicity against peripheral blood cells were tested using the concentration of IC50 for both trials and twice the IC50 for analysis in flow cytometry, indicating that CaL is not toxic to these cells. To assess the mechanism of cell death caused by CaL in HeLa cells, we performed flow cytometry and western blotting. The results showed the lectin probably induces cell death by apoptosis activation by pro-apoptotic protein Bax, promoting mitochondrial membrane permeabilization, cell cycle arrest in S phase, with accumulation of cells of approximately 57% in this phase, and acting as both dependent and/or independent of caspases pathway. These results suggest that CaL has the potential to be used as drug treatment against cancer.

Análise de agrupamentos dos dados de DFA oriundos de perfis elétricos de indução de poços de petróleo

The main objective of this study is to apply recently developed methods of physical-statistic to time series analysis, particularly in electrical induction s profiles of oil wells data, to study the petrophysical similarity of those wells in a spatial distribution. For this, we used the DFA method in order to know if we can or not use this technique to characterize spatially the fields. After obtain the DFA values for all wells, we applied clustering analysis. To do these tests we used the non-hierarchical method called K-means. Usually based on the Euclidean distance, the K-means consists in dividing the elements of a data matrix N in k groups, so that the similarities among elements belonging to different groups are the smallest possible. In order to test if a dataset generated by the K-means method or randomly generated datasets form spatial patterns, we created the parameter Ω (index of neighborhood). High values of Ω reveals more aggregated data and low values of Ω show scattered data or data without spatial correlation. Thus we concluded that data from the DFA of 54 wells are grouped and can be used to characterize spatial fields. Applying contour level technique we confirm the results obtained by the K-means, confirming that DFA is effective to perform spatial analysis

Sistema de sensoriamento eletromagnético utilizado para detecção da contaminação do óleo isolante do motor no método de elevação artificial do tipo bombeio centrífugo submerso

In the artificial lift method by Electrical Submersible Pump (ESP), the energy is transmitted for the well´s deep through a flat electric handle, where it is converted into mechanical energy through an engine of sub-surface, which is connected to a centrifugal pump. This transmits energy to the fluid under the pressure form, bringing it to the surface In this method the subsurface equipment is basically divided into: pump, seal and motor. The main function of the seal is the protect the motor, avoiding the motor´s oil be contaminated by oil production and the consequent burning of it. Over time, the seal will be wearing and initiates a contamination of motor oil, causing it to lose its insulating characteristics. This work presents a design of a magnetic sensor capable of detecting contamination of insulating oil used in the artificial lift method of oil-type Electrical Submersible Pump (ESP). The objective of this sensor is to generate alarm signal just the moment when the contamination in the isolated oil is present, enabling the implementation of a predictive maintenance. The prototype was designed to work in harsh conditions to reach a depth of 2000m and temperatures up to 150°C. It was used a simulator software to defined the mechanical and electromagnetic variables. Results of field experiments were performed to validate the prototype. The final results performed in an ESP system with a 62HP motor showed a good reliability and fast response of the prototype.

Avaliação do desempenho funcional de crianças com paralisia cerebral de acordo com níveis de comprometimento motor

Contextualization: Several studies have examined the mobility of this group of children, however little is known about the impact of motor function in activities of daily living, considering the seriousness of their neuromotor damage. Objective: Identify the functional differences of children with Cerebral Palsy with different levels of motor dysfunction and correlate these differences with the areas of mobility, self-care and social function in functional ability and caregiver´s assistance of these children. Methods: An l analytical cross-section search was developed, which were part 70 children / families aged from 4 to 7.5 years, in the Rehabilitation Center for Children. As tools were used the Pediatric Evaluation Disability Inventory (PEDI) and the Gross Motor Function Classification System (GMFCS). Data analysis was performed by ANOVA and Pearson's correlation tests. Results: The results show the functional variability of children CP in different severity levels of motor disfunction This variation was observed in the areas of mobility, self-care and social function. The results also showed a strong correlation between the domains mobility and self-care, mobility and social function. Conclusions: The variability shown by the children with CP, suggests the use of PEDI and GMFCS as this association appears to increase the understanding of how the gross motor functions are related to activities of daily living, describing the best commitments and their degree of impact on functional activities. This correlation demonstrates how mobility is crucial to evaluate the performance and guide the therapeutic practice, to develop the children´s potencial, and guide the caregiver in stimulation

Estado nutricional, desempenho motor e marcadores dermatoglíficos em escolares púberes

A fase da puberdade é o período em que ocorrem as maiores transformações características da adolescência. Por essa razão, este estudo objetivou identificar o estado nutricional, desempenho motor e marcadores dermatoglíficos em 2363 escolares púberes selecionados de forma estratificada, de ambos os sexos, com idades variando de 6 a 15 anos, matriculados no Ensino Fundamental (2ª a 9ª Séries) do ensino público no estado do Rio Grande do Norte. Foram avaliados o estado nutricional (Índice de Massa Corporal); as qualidades físicas básicas ( testes de coordenação, equilíbrio, agilidade, flexibilidade, força e velocidade); o potencial genético (método da dermatoglifia) e o estágio maturacional (auto avaliação de Tanner); Com relação ao estado nutricional observou-se que escolares acima do peso apresentam valores mais baixos em relação ao seu desempenho motor sendo esses valores, mais significativos nos meninos. No que se refere à maturação sexual, os resultados apontaram que os meninos atingem os estágios maturacionais primeiro que as meninas, não tendo encontrado correlação entre o potencial genético e os demais indicadores o que nos permite concluir que os escolares do estado do Rio Grande do Norte, principalmente os do sexo masculino sofrem influência significativa de seu estado nutricional e seu estágio maturacional no que diz respeito ao seu desempenho motor. Essa dissertação apresenta relação de interdisciplinaridade, tendo o seu conteúdo uma aplicação nos campos da Educação Física, Nutrição, Medicina e Enfermagem.

Controle vetorial de velocidade de uma máquina de indução sem mancais trifásica com bobinado dividido utilizando estimação neural de fluxo

This work describes the study and the implementation of the vector speed control for a three-phase Bearingless induction machine with divided winding of 4 poles and 1,1 kW using the neural rotor flux estimation. The vector speed control operates together with the radial positioning controllers and with the winding currents controllers of the stator phases. For the radial positioning, the forces controlled by the internal machine magnetic fields are used. For the radial forces optimization , a special rotor winding with independent circuits which allows a low rotational torque influence was used. The neural flux estimation applied to the vector speed controls has the objective of compensating the parameter dependences of the conventional estimators in relation to the parameter machine s variations due to the temperature increases or due to the rotor magnetic saturation. The implemented control system allows a direct comparison between the respective responses of the speed and radial positioning controllers to the machine oriented by the neural rotor flux estimator in relation to the conventional flux estimator. All the system control is executed by a program developed in the ANSI C language. The DSP resources used by the system are: the Analog/Digital channels converters, the PWM outputs and the parallel and RS-232 serial interfaces, which are responsible, respectively, by the DSP programming and the data capture through the supervisory system

Uma proposta de regulador nebuloso para geradores eólicos de indução

This work presents a proposal for a voltage and frequency control system for a wind power induction generator. It has been developed na experimental structure composes basically by a three phase induction machine, a three phase capacitor and a reactive static Power compensator controlled by histeresys. lt has been developed control algorithms using conventional methods (Pl control) and linguistic methods (using concepts of logic and fuzzy control), to compare their performances in the variable speed generator system. The control loop was projected using the ADJDA PCL 818 model board into a Pentium 200 MHz compu ter. The induction generator mathematical model was studied throught Park transformation. It has been realized simulations in the Pspice@ software, to verify the system characteristics in transient and steady-state situations. The real time control program was developed in C language, possibilish verify the algorithm performance in the 2,2kW didatic experimental system

Aplicação de sistemas multi-classificadores no diagnóstico de falhas em motores de indução trifásicos

Equipment maintenance is the major cost factor in industrial plants, it is very important the development of fault predict techniques. Three-phase induction motors are key electrical equipments used in industrial applications mainly because presents low cost and large robustness, however, it isn t protected from other fault types such as shorted winding and broken bars. Several acquisition ways, processing and signal analysis are applied to improve its diagnosis. More efficient techniques use current sensors and its signature analysis. In this dissertation, starting of these sensors, it is to make signal analysis through Park s vector that provides a good visualization capability. Faults data acquisition is an arduous task; in this way, it is developed a methodology for data base construction. Park s transformer is applied into stationary reference for machine modeling of the machine s differential equations solution. Faults detection needs a detailed analysis of variables and its influences that becomes the diagnosis more complex. The tasks of pattern recognition allow that systems are automatically generated, based in patterns and data concepts, in the majority cases undetectable for specialists, helping decision tasks. Classifiers algorithms with diverse learning paradigms: k-Neighborhood, Neural Networks, Decision Trees and Naïves Bayes are used to patterns recognition of machines faults. Multi-classifier systems are used to improve classification errors. It inspected the algorithms homogeneous: Bagging and Boosting and heterogeneous: Vote, Stacking and Stacking C. Results present the effectiveness of constructed model to faults modeling, such as the possibility of using multi-classifiers algorithm on faults classification

Implementação experimental de filtro ativo paralelo de potência com aplicação a gerador de indução trifásico

This work describes the experimental implementation of a shunt active power filter applied to a three-phase induction generator. The control strategy of active filter turned to the excitation control of the machine and to decrease the harmonics in the generator output current. Involved the implementation of a digital PWM switching, and was made a comparison of two techniques for obtaining the reference currents. The first technique is based on the synchronous dq reference method and the second on the theory of instantaneous power. The comparison is performed via simulation and experimental results. To obtain the experimental results, was mounted a bench trial and the control and communications needed were implemented using DSP - MS320F2812. The simulation results and experimental data proved the efficiency of the filter to apply, highlighting the technique of instantaneous power

Controlador adaptativo por posicionamento de pólos e estrutura variável aplicado ao controle de geradores eólicos baseados em máquina de indução duplamente alimentada

In the last decade, the renewable energy sources have present a major propulsion in the world due to several factors: political, environmental, financial and others. Within this context, we have in particular the energy obtained through wind, wind energy - that has highlighted with rapid growth in recent years, including in Brazil, mostly in the Northeast, due to it s benefit-cost between the clean energies. In this context, we propose to compare the variable structure adaptive pole placement control (VS-APPC) with a traditional control technique proportional integral controller (PI), applied to set the control of machine side in a conversion system using a wind generator based on Double-Fed Induction Generator (DFIG). Robustness and performance tests were carried out to the uncertainties of the internal parameters of the machine and variations of speed reference.

Mecanismos de desgaste, história térmica e ciclo de vida de componentes de um motor de combustão interna de aeromodelo

We developed an assay methodology that considered the temperature variation and the scanning electron microscopy as a method to quantify and characterize respectively the consumption evolution in three 46 LA machines, with internal combustion and two-stroke engines, 7.64 cm3 cylinder capacity, 23.0 millimeters diameter and 18.4 millimeters course, RPM service from 2.000 to 16.000 rpm, 1.2 HP power, and 272 grams weight. The investigated engines components were: (1) head of the engine (Al-Si alloy), (2) piston (Al-Si alloy) and (3) piston pin (AISI 52100 steel). The assays were carried out on a desktop; engines 1 and 2 were assayed with no load, whereas in two assays of engine 3 we added a fan with wind speed that varied from 8.10 m/s to 11.92 m/s, in order to identify and compare the engine dynamic behavior as related to the engines assayed with no load. The temperatures of the engine s surface and surroundings were measured by two type K thermopairs connected to the assay device and registered in a microcomputer with data recording and parameters control and monitoring software, throughout the assays. The consumed surface of the components was analyzed by scanning electron microscopy (SEM) and microanalysis-EDS. The study was complemented with shape deformation and mass measurement assays. The temperature variation was associated with the oxides morphology and the consumption mechanisms were discussed based on the relation between the thermal mechanical effects and the responses of the materials characterization

Análise da indução de fluxo de ar por convecção livre em chaminé solar

Experiments were performed to study the effect of surface properties of a vertical channel heated by a source of thermal radiation to induce air flow through convection. Two channels (solar chimney prototype) were built with glass plates, forming a structure of truncated pyramidal geometry. We considered two surface finishes: transparent and opaque. Each stack was mounted on a base of thermal energy absorber with a central opening for passage of air, and subjected to heating by a radiant source comprises a bank of incandescent bulbs and were performed field tests. Thermocouples were fixed on the bases and on the walls of chimneys and then connected to a data acquisition system in computer. The air flow within the chimney, the speed and temperature were measured using a hot wire anemometer. Five experiments were performed for each stack in which convective flows were recorded with values ranging from 17 m³ / h and 22 m³ / h and air flow velocities ranging from 0.38 m / s and 0.56 m / s for the laboratory tests and air velocities between 0.6 m/s and 1.1m/s and convective airflows between 650 m³/h and 1150 m³/h for the field tests. The test data were compared to those obtained by semi-empirical equations, which are valid for air flow induced into channels and simulated data from 1st Thermodynamics equation. It was found that the chimney with transparent walls induced more intense convective flows than the chimney with matte finish. Based on the results obtained can be proposed for the implementation of prototype to exhaust fumes, mists, gases, vapors, mists and dusts in industrial environments, to help promote ventilation and air renewal in built environments and for drying materials, fruits and seeds

Estudo da influência de pré-tratamentos de dois resíduos lignocelulósicos (bagaço do pedúnculo de caju e casca de coco) utilizados como substrato na indução à síntese de enzimas celulolíticas

Nowadays generation ethanol second, that t is obtained from fermentation of sugars of hydrolyses of cellulose, is gaining attention worldwide as a viable alternative to petroleum mainly for being a renewable resource. The increase of first generation ethanol production i.e. that obtained from sugar-cane molasses could lead to a reduction of lands sustainable for crops and food production. However, second generation ethanol needs technologic pathway for reduce the bottlenecks as production of enzymes to hydrolysis the cellulose to glucose i.e. the cellulases as well as the development of efficient biomass pretreatment and of low-cost. In this work Trichoderma reesei ATCC 2768 was cultivated under submerged fermentation to produce cellulases using as substrates waste of lignocellulosic material such as cashew apple bagasse as well as coconut bagasse with and without pretreatment. For pretreatment the bagasses were treated with 1 M NaOH and by explosion at high pressure. Enzyme production was carried out in shaker (temperature of 27ºC, 150 rpm and initial medium pH of 4.8). Results showed that T.reesei ATCC 2768 showed the higher cellulase production when the cashew apple bagasse was treated with 1M NaOH (2.160 UI/mL of CMCase and 0.215 UI/mL of FPase), in which the conversion of cellulose, in terms of total reducing sugars, was of 98.38%, when compared to pretreatment by explosion at high pressure (0.853 UI/mL of CMCase and 0.172 UI/mL of Fpase) showing a conversion of 47.39% of total reducing sugars. Cellulase production is lower for the medium containing coconut bagasse treated with 1M NaOH (0.480 UI/mL of CMcase and 0.073 UI/mL of FPase), giving a conversion of 49.5% in terms of total reducing sugars. Cashew apple bagasse without pretreatment showed cellulase activities lower (0.535 UI/mL of CMCase and 0,152 UI/mL of FPase) then pretreated bagasse while the coconut bagasse without pretreatment did not show any enzymatic activity. Maximum cell concentration was obtained using cashew nut bagasse as well as coconut shell bagasse treated with 1M NaOH, with 2.92 g/L and 1.97 g/L, respectively. These were higher than for the experiments in which the substrates were treated by explosion at high pressure, 1.93 g/L and 1.17 g/L. Cashew apple is a potential inducer for cellulolytic enzymes synthysis showing better results than coconut bagasse. Pretreatment improves the process for the cellulolytic enzyme production

Interpretação e análise do problema da indução sob uma visão fundamentada em teorias de conjuntos e teoria de probabilidades

The following work is to interpret and analyze the problem of induction under a vision founded on set theory and probability theory as a basis for solution of its negative philosophical implications related to the systems of inductive logic in general. Due to the importance of the problem and the relatively recent developments in these fields of knowledge (early 20th century), as well as the visible relations between them and the process of inductive inference, it has been opened a field of relatively unexplored and promising possibilities. The key point of the study consists in modeling the information acquisition process using concepts of set theory, followed by a treatment using probability theory. Throughout the study it was identified as a major obstacle to the probabilistic justification, both: the problem of defining the concept of probability and that of rationality, as well as the subtle connection between the two. This finding called for a greater care in choosing the criterion of rationality to be considered in order to facilitate the treatment of the problem through such specific situations, but without losing their original characteristics so that the conclusions can be extended to classic cases such as the question about the continuity of the sunrise