91 resultados para Estação ferroviária
Resumo:
The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible
Resumo:
Pipelines for the transport of crude oil from the production wells to the collecting stations are named production lines . These pipes are subjected to chemical and electrochemical corrosion according to the environment and the type of petroleum transported. Some of these lines, depending upon the composition of the fluid produced, may leak within less than one year of operation due to internal corrosion. This work aims at the development of composite pipes with an external protecting layer of high density polyurethane for use in production lines of onshore oil wells, meeting operational requirements. The pipes were manufactured using glass fibers, epoxy resin, polyester resin, quartz sand and high density polyurethane. The pipes were produced by filament winding with the deposition of high density polyurethane on the external surface and threaded ends (API 15 HR/PM-VII). Three types of pipes were manufactured: glass/epoxy, glass/epoxy with an external polyurethane layer and glass/epoxy with an intermediate layer of glass fiber, polyester, sand and with an external polyurethane layer. The three samples were characterized by Scanning Electronic Microscopy (SEM) and for the determination of constituent content. In addition, the following tests were conducted: hydrostatic test, instant rupture, shorttime failure pressure, Gardner impact, transverse stiffness and axial tension. Field tests were conducted in Mossoró RN (BRAZIL), where 1,677 meters of piping were used. The tests results of the three types of pipes were compared in two events: after two months from manufacturing of the samples and after nine months of field application. The results indicate that the glass/epoxy pipes with an intermediate layer of fiber glass composite, polyester e sand and with an external layer of high density polyurethane showed superior properties as compared to the other two and met the requirements of pressure class, axial tensile strength, transverse stiffness, impact and environmental conditions, for onshore applications as production lines
Resumo:
The production of water has become one of the most important wastes in the petroleum industry, specifically in the up stream segment. The treatment of this kind of effluents is complex and normally requires high costs. In this context, the electrochemical treatment emerges as an alternative methodology for treating the wastewaters. It employs electrochemical reactions to increase the capability and efficiency of the traditional chemical treatments for associated produced water. The use of electrochemical reactors can be effective with small changes in traditional treatments, generally not representing a significant additional surface area for new equipments (due to the high cost of square meter on offshore platforms) and also it can use almost the same equipments, in continuous or batch flow, without others high costs investments. Electrochemical treatment causes low environmental impact, because the process uses electrons as reagent and generates small amount of wastes. In this work, it was studied two types of electrochemical reactors: eletroflocculation and eletroflotation, with the aim of removing of Cu2+, Zn2+, phenol and BTEX mixture of produced water. In eletroflocculation, an electrical potential was applied to an aqueous solution containing NaCl. For this, it was used iron electrodes, which promote the dissolution of metal ions, generating Fe2+ and gases which, in appropriate pH, promote also clotting-flocculation reactions, removing Cu2+ and Zn2+. In eletroflotation, a carbon steel cathode and a DSA type anode (Ti/TiO2-RuO2-SnO2) were used in a NaCl solution. It was applied an electrical current, producing strong oxidant agents as Cl2 and HOCl, increasing the degradation rate of BTEX and phenol. Under different flow rates, the Zn2+ was removed by electrodeposition or by ZnOH formation, due the increasing of pH during the reaction. To better understand the electrochemical process, a statistical protocol factor (22) with central point was conducted to analyze the sensitivity of operating parameters on removing Zn2+ by eletroflotation, confirming that the current density affected the process negatively and the flow rate positively. For economical viability of these two electrochemical treatments, the energy consumption was calculated, taking in account the kWh given by ANEEL. The treatment cost obtained were quite attractive in comparison with the current treatments used in Rio Grande do Norte state. In addition, it could still be reduced for the case of using other alternative energy source such as solar, wind or gas generated directly from the Petrochemical Plant or offshore platforms
Resumo:
This document aims to improve the quality of the production test in vertical tanks with free water drain pipes, through a device to control the draining system. This proposal consists of an interface detector close to the tank bottle and a control valve on the pipe-drain; they are attached to a remote supervisor system, which will be minimizing the human influence in the conclusion of the test result. And for more consciousness the work shows the importance of the wells production test in the attendance and diagnosis of the productive process, informing the large number of tests executed and problems of the procedure adopted in the field today. There are many possible sources of uncertainty in this kind of test as shown in the experiments realized in the field; the object prototype of this dissertation will be made in the field, based upon the definition of parameters and characteristics of the devices proposal. For a better definition of the draining process the action results of the assessment test are shown, especially changed some for the understand ing of the real process. It shows the proposal details and the configuration that will be used in the tank of Monte Alegre s field Production Station, explaining the interface detector kind and the control system. It is the base to a pilot project now in development, named as the new project classified in the status of the new technology and production improvement of PETROBRAS in Rio Grande do Norte and Ceará. This dissertation concludes that the automation of the conventional test with the draining system will bring benefits both economically as metrologically, because it reduces the uncertainty of the test procedures with free water draining, and also decreases the number of tests with problems
Resumo:
One of the main activities in the petroleum engineering is to estimate the oil production in the existing oil reserves. The calculation of these reserves is crucial to determine the economical feasibility of your explotation. Currently, the petroleum industry is facing problems to analyze production due to the exponentially increasing amount of data provided by the production facilities. Conventional reservoir modeling techniques like numerical reservoir simulation and visualization were well developed and are available. This work proposes intelligent methods, like artificial neural networks, to predict the oil production and compare the results with the ones obtained by the numerical simulation, method quite a lot used in the practice to realization of the oil production prediction behavior. The artificial neural networks will be used due your learning, adaptation and interpolation capabilities
Resumo:
The objective of this Doctoral Thesis was monitoring, in trimestral scale, the coastal morphology of the Northeastern coast sections of Rio Grande do Norte State, in Brazil, which is an area of Potiguar Basin influenced by the oil industry activities. The studied sections compose coastal areas with intense sedimentary erosion and high environmental sensitivity to the oil spill. In order to achieve the general objective of this study, the work has been systematized in four steps. The first one refers to the evaluation of the geomorphological data acquisition methodologies used on Digital Elevation Model (DEM) of sandy beaches. The data has been obtained from Soledade beach, located on the Northeastern coast of Rio Grande Norte. The second step has been centered on the increasing of the reference geodetic infrastructure to accomplish the geodetic survey of the studied area by implanting a station in Corta Cachorro Barrier Island and by conducting monitoring geodetic surveys to understand the beach system based on the Coastline (CL) and on DEM multitemporal analysis. The third phase has been related to the usage of the methodology developed by Santos; Amaro (2011) and Santos et al. (2012) for the surveying, processing, representation, integration and analysis of Coastlines from sandy coast, which have been obtained through geodetic techniques of positioning, morphological change analysis and sediment transport. The fourth stage represents the innovation of surveys in coastal environment by using the Terrestrial Laser Scanning (TLS), based on Light Detection and Ranging (LiDAR), to evaluate a highly eroded section on Soledade beach where the oil industry structures are located. The evaluation has been achieved through high-precision DEM and accuracy during the modeling of the coast morphology changes. The result analysis of the integrated study about the spatial and temporal interrelations of the intense coastal processes in areas of building cycles and destruction of beaches has allowed identifying the causes and consequences of the intense coastal erosion in exposed beach sections and in barrier islands
Resumo:
The composition of termite assemblages was analyzed at three Caatinga sites of the Seridó Ecological Station, located in the municipality of Serra Negra do Norte, in the state of Rio Grande do Norte, Brazil. These sites have been subjected to selective logging, and cleared for pasture and farming. A standardized sampling protocol for termite assemblages (30h/person/site) was conducted between September 2007 and February 2009. At each site we measured environmental variables, such as soil granulometry, pH and organic matter, necromass stock, vegetation height, tree density, stem diameter at ankle height (DAH) and the largest and the smallest crown width. Ten species of termites, belonging to eight genera and three families, were found at the three experimental sites. Four feeding-groups were sampled: wood-feeders, soil-feeders, wood-soil interface feeders and leaf-feeders. The wood-feeders were dominant in number of species and number of encounters at all sites. In general, the sites were not significantly different in relation to the environmental variables measured. The same pattern was observed for termite assemblages, where no significant differences in species richness, relative abundance and taxonomic and functional composition were observed between the three sites. The agreement between the composition of assemblages and environmental variables reinforces the potential of termites as biological indicators of habitat quality
Resumo:
A taxonomic survey of representatives of the genus Geastrum took place during the rainy season from 2006 to 2009 in four districts in the state of Rio Grande do Norte: Parque Estadual Dunas do Natal (Atlantic Forest), Mata do Jiqui EMPARN (Atlantic Forest) and Estação Ecológica do Seridó (Caatinga). Fourteen species were recorded: G. entomophilum, G. fimbriatum, G. hirsutum, G. javanicum, G. lageniforme, G. lloydianum, G. minimum, G. morganii, G. ovalisporum, G. pectinatum, G. saccatum, G. schweinitzii, G. setiferum and G. triplex. Of these species, eleven occurred in the Atlantic Forest and six in the Caatinga. A new species has been recorded to science, G. entomophilum, other as a first record for Brazil, G. morganii, six new records for the Northeast, and ten new records for Rio Grande do Norte. The material was tumbled in the Herbarium UFRN. Additionally, a survey of the species of the genus deposited in the Herbarium UFRN was accomplished, resulting in 244 herbarium specimens belonging to thirty-three species. Of these ones, twenty-three were collected in Brazil and ten are from Czech Republic, Europe, as donation from the VZ Herbarium
Resumo:
It is estimated that the Brazilian karst areas sum about 200.000 km2. The caves, one of the main components of karst, are important windows into the biological studies on hypogean environments. In Rio Grande do Norte are known 563 caves, and 476 of them are in the municipalities of Baraúna, Felipe Guerra, Governador Dix-Sept Rosado, Apodi and Mossoró, the Western region of the State. However, like in the rest of the country, the cave fauna of the State is still poorly understood. This study used data from invertebrates harvested in 47 caves and aimed to analyze the effect of environmental change between the dry and rainy seasons in the communities of cave invertebrates, characterize these communities and evaluate the relationships between morphological and biotic variables of the caves and surroundings, and to define priority areas for conservation of cave environments of the study area from biotic parameters. Strong effects were found in the community structure of cave invertebrates due environmental changes between seasons, with values of total richness, abundance, diversity and ecological complexity significantly higher in the rainy season. It was possible to assess how the morphology of the cave and the external environment variables affect the biotic system, so that the variety of resources, forest cover in the vicinity, the area of the cave and its entrance were the variables that best explained the structure communities of cave invertebrates in the region. High values of total richness of invertebrates (36,62 ± 14,04 spp / cave) and troglomorphic species (61 species, mean 1,77 ± 2,34 spp / cave) were found and, given the biological relevance in the context of the area national and the imminent anthropogenic pressures existing, we defined four priority areas for actions aiming cave biodiversity conservation in the region.
Resumo:
The Northeast of Brazil (NEB) shows high climate variability, ranging from semiarid regions to a rainy regions. According to the latest report of the Intergovernmental Panel on Climate Change, the NEB is highly susceptible to climate change, and also heavy rainfall events (HRE). However, few climatology studies about these episodes were performed, thus the objective main research is to compute the climatology and trend of the episodes number and the daily rainfall rate associated with HRE in the NEB and its climatologically homogeneous sub regions; relate them to the weak rainfall events and normal rainfall events. The daily rainfall data of the hydrometeorological network managed by the Agência Nacional de Águas, from 1972 to 2002. For selection of rainfall events used the technique of quantiles and the trend was identified using the Mann-Kendall test. The sub regions were obtained by cluster analysis, using as similarity measure the Euclidean distance and Ward agglomerative hierarchical method. The results show that the seasonality of the NEB is being intensified, i.e., the dry season is becoming drier and wet season getting wet. The El Niño and La Niña influence more on the amount of events regarding the intensity, but the sub-regions this influence is less noticeable. Using daily data reanalysis ERAInterim fields of anomalies of the composites of meteorological variables were calculated for the coast of the NEB, to characterize the synoptic environment. The Upper-level cyclonic vortex and the South atlantic convergene zone were identified as the main weather systems responsible for training of EPI on the coastland
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
Resumo:
This Study inserts in Mathematical Education & Education that search to investigate the (self) formation of formers that gets graduation e pass to graduate others that get graduation and are formers in Mathematical Education. This Is a qualitative search in a perspective from search-formation.The work is formed of four topics. First topic talks about : The self-formation of formers. Second topic: at way of suppositions theorical-methodological from search. Third topic tells over: The life of a former life. Fouth topic A Station called Ubiratan D´Ambrosio created in his reverence and for build all the Knowledge´s Corpus developed by his studies and searches. It´s in sense of come and go from knowledge created at action by mankind to get finality of Transcendency and Survive. Look for to investigate aspects of academical, professional and personal life where are translated in language, thinking and practices oriented for one know-how holistical and transdiciplined in a reflexion, search and the critical it constitute to be a Professor, Teacher, Searcher and Etnomathematic that confered him the merit in 2005 the Prize Félix Klein, that declared Valente (2007), maximum distinction that can receive someone from Mathematical Education. The results point that the narratives of life´s stories are prominences to one re-direction of teach practical in formation´s courses of Mathematical teachers, opening spaces for what the teachers and particularly of Mathematical thinking and take position about your process of formation to be Formers. The Study also given possibilities to propose fourteen stoppages in Station that are beginnings with direction that emerge from studies and searches about the trajectory of life of Professor Ubiratan D´Ambrosio in perspective of re-signify the formative process in education and Mathematical Education
Resumo:
In the current conjuncture, the environmental factor has been changing the position of companies that are practicing or minimally adopting environmental management. Such tool has been used by companies to face the problems caused by solid waste, in particular green coconut waste, which is constantly among the material discarded by society (companies/ consumer). It is a typical tropical fruit whose fresh water is very benefic for human health, and its popularization has caused a progressive increase of its consumption. Following this stream of thought, this present work came up with an analysis of strengths, weaknesses, threats, and opportunities SWOT analysis on green coconut solid waste management at two agribusiness companies in the state of Rio Grande do Norte (RN), Brazil, aiming to know the challenges and the potentials of this kind of waste. According to the approach of the problem, this work fits a descriptive, exploratory, and qualitative research. The data collection was obtained by a questionnaire and a structured interview, in order to evaluate the strategic posture of agribusiness companies through SWOT analysis, which is an English acronym for Strengths, Weaknesses, Opportunities and Threats. The SWOT analysis is an effective tool to analyze the internal and external environment of an organization. This tool contributes to locate the company at the environment in question and when well applied it enables the detection of mistakes, the strengthening of correct procedures, the avoidance of threats, and the bet on opportunities. The studied agribusiness industries have very similar profiles, such as a long business life span, and a strategy that extends the useful life of the fruit, by using its waste for the manufacturing of new subproducts. In both, the daily quantity of waste resulted of this process reaches approximately 20 thousand units of the fruit in high season, being necessary a focus directed at use and/or treatment of these waste. Further to SWOT analysis, it was ascertained that the agribusiness company A works through a defensive marketing strategy and acts vulnerably, in other words, unable of acting before this market segment, for it has decided to stop using the waste due to a lack of equipment and technology. On the other hand, the agribusiness company B has incorporated an offensive marketing strategy because even not possessing equipments, technology, and appropriated internal installations, it still insists on use and benefits of green coconut waste in its agribusiness. Thus, it is considered that the potential of green coconut waste management for the production of several subproducts reduces the impacts produced by inappropriate placement and generates profits in a short, medium and long term. Such profits being tangible and intangible, as the interest for sustainability actions is not only a matter of obtaining return on capital, but it is an important question in order to move on into business, since it is not enough to have quality on products and process nowadays. It is necessary to establish socio-environmental practices aiming the image of the company as the prevailing role on consumers buying decision